Integral hollow fiber membrane with chemical cross-linking for pressure retarded osmosis operated in the orientation of active layer facing feed solution

Harvesting Blue Energy Based on Salinity and Temperature Gradient: Challenges, Solutions, and Opportunities

Greenhouse gas emissions associated with power generation from fossil fuel combustion account for 25% of global emissions and, thus, contribute greatly to climate change. Renewable energy sources, like wind and solar, have reached a mature stage, with costs aligning with those of fossil fuel-derived power but suffer from the challenge of intermittency due to the variability of wind and sunlight. This study aims to explore the viability of salinity gradient power, or "blue energy", as a clean, renewable source of uninterrupted, base-load power generation. Harnessing the salinity gradient energy from river estuaries worldwide could meet a substantial portion of the global electricity demand (approximately 7%). Pressure retarded osmosis (PRO) and reverse electrodialysis (RED) are more prominent technologies for blue energy harvesting, whereas thermo-osmotic energy conversion (TOEC) is emerging with new promise. This review scrutinizes the obstacles encountered in developing osmotic power generation using membrane-based methods and presents potential solutions to overcome challenges in practical applications. While certain strategies have shown promise in addressing some of these obstacles, further research is still required to enhance the energy efficiency and feasibility of membrane-based processes, enabling their large-scale implementation in osmotic energy harvesting.

Fluidics for energy harvesting: from nano to milli scales

A large amount of untapped energy sources surrounds us. In this review, we summarize recent works of water-based energy harvesting systems with operation scales ranging from miniature systems to large scale attempts. We focus particularly on the triboelectric energy, which is produced when a liquid and a solid come into contact, and on the osmotic energy, which is released when salt water and fresh water are mixed. For both techniques we display the state of the art understanding (including electrical charge separation, electro-osmotic currents and induced currents) and the developed devices. A critical discussion of present works confirms the significant progress of these water-based energy harvesting systems in all scales. However, further efforts in efficiency and performance amelioration are expected for these technologies to accelerate the industrialization and commercialization procedure.

Modification of Thin Film Composite Pressure Retarded Osmosis Membrane by Polyethylene Glycol with Different Molecular Weights

An investigation of the effect of the molecular weight of polyethylene glycol (PEG) on thin-film composite (TFC) flat sheet polysulfone membrane performance was conducted systematically, for application in forward osmosis (FO) and pressure retarded osmosis (PRO). The TFC flat sheet PSf-modified membranes were prepared via a non-solvent phase-separation technique by introducing PEGs of different molecular weights into the dope solution. The TFC flat sheet PSf-PEG membranes were characterized by SEM, FTIR and AFM. The PSf membrane modified with PEG 600 was found to have the optimum composition. Under FO mode, this modified membrane had a water permeability of 12.30 Lm-2h-1 and a power density of 2.22 Wm-2, under a pressure of 8 bar in PRO mode, using 1 M NaCl and deionized water as the draw and feed solutions, respectively. The high water permeability and good mechanical stability of the modified TFC flat sheet PSF-PEG membrane in this study suggests that this membrane has great potential in future osmotically powered generation systems.

Development of layer-by-layer assembled polyamide-imide membranes for oil sands produced water treatment

The sustainable expansion of steam-assisted gravity drainage, as one of the most popular enhanced oil recovery methods, strongly depends on the proper management of the produced water. The strict environmental regulations have forced the oil sands industry to treat and reuse the produced water for oil extraction. Membrane separation as a single-step water treatment technique has played an important role in removing multiple-sized contaminants from wastewater. However, fouling limits the widespread application of this technology if the membrane is not modified properly to achieve antifouling propensities. Herein, we used the layer-by-layer assembly technique to sequentially coat the hydrophilic poly(diallyl dimethylammonium chloride) and polyacrylic acid on the surface of the polyamide-imide porous membrane to improve its fouling resistance. The effect of the number of bilayers on fouling and permeation properties was examined. The membrane with the highest fouling resistance and reasonable hydrodynamic permeability of 5.2 LMH/psi was achieved by coating four bilayers. This membrane exhibited a low flux decline of 50.2% and a high flux recovery ratio of 100%, while these numbers for the pristine PAI membrane were 75.9% and 97.8% under similar test conditions. The enhanced antifouling characteristics of the modified membranes indicate the viability of these membranes for oil sands produced water treatment with an easy cleaning procedure. The key parameter that contributed to the enhanced fouling resistance of the bilayer-coated membranes was the improved surface hydrophilicity, which manifests through the reduction of water contact angle from 62° ± 3° for the pristine membrane to 52° ± 2° for surface-modified membranes.

Thermal associated pressure-retarded osmosis processes for energy production: A review

Climate change is an existential threat to global environments and human life. To achieve global mean temperature rise of below 1.5 °C, increasing utilization of renewable energy and minimizing CO₂ emission from fossil fuel industries have been emphasized by the United Nations. Pressure-retarded osmosis (PRO) has displayed its technical feasibility in capturing renewable energy from the salinity gradient of two streams through a semipermeable membrane. Towards achieving economic feasible PRO, process optimization, waste stream/heat utilization, and hybrid PRO processes have been attempted by theoretically modelling and experimental examination. Among these efforts, the thermal associated PRO processes have received great attention due to their improved power generation. In this paper, we aim to provide a comprehensive review on thermal associated PRO processes, focusing on the role of thermal behaviour in both stand-alone PRO and hybrid PRO processes (e.g. PRO-membrane distillation, PRO-thermosiphon, PRO-solar pond). Meanwhile, thermal associated draw solution development has been highlighted. Finally, a combination of PRO with high temperature/high pressure geothermal waste gas as draw solution is proposed and its technical and economic feasibility is discussed, especially under Icelandic scenario.

Forward Osmosis: A Critical Review

The use of forward osmosis (FO) for water purification purposes has gained extensive attention in recent years. In this review, we first discuss the advantages, challenges and various applications of FO, as well as the challenges in selecting the proper draw solution for FO, after which we focus on transport limitations in FO processes. Despite recent advances in membrane development for FO, there is still room for improvement of its selective layer and support. For many applications spiral wound membrane will not suffice. Furthermore, a defect-free selective layer is a prerequisite for FO membranes to ensure low solute passage, while a support with low internal concentration polarization is necessary for a high water flux. Due to challenges affiliated to interfacial polymerization (IP) on non-planar geometries, we discuss alternative approaches to IP to form the selective layer. We also explain that, when provided with a defect-free selective layer with good rejection, the membrane support has a dominant influence on the performance of an FO membrane, which can be estimated by the structural parameter (S). We emphasize the necessity of finding a new method to determine S, but also that predominantly the thickness of the support is the major parameter that needs to be optimized.