ZIF-8 particle size effects on reverse osmosis performance of polyamide thin-film nanocomposite membranes: Importance of particle deposition

A signal amplifying MOF-based probe:on-site and ultrasensitive dual-channel portable detection of Hg2+ in groundwater through a fluorimetrically and RGB-based sensing assay

Mercury (II) ions (Hg2+) are a significant source of heavy metal contamination in groundwater, posing a serious threat to human health and the environment. Therefore, there is an urgent need for the development of a new detection technique with high sensitivity for monitoring Hg2+ in contaminated groundwater. Here, we developed a signal amplifying MOF-based probe (NXS@ZIF-8) for on-site and ultrasensitive dual-channel portable detection of Hg2+ in groundwater. The successful grafting of the fluorescent probe (NXS) onto ZIF-8 effectively enhanced the enrichment of the NXS probe, thereby amplifying the detection signal for Hg2+. Upon exposure to Hg2+, NXS@ZIF-8 quickly emits fluorescent signals, which can be easily detected using portable laser-induced fluorescence spectrometers (LIFs) with a low detection limit of 0.30 ppb. Importantly, the platform enables on-site detection of Hg2+ in groundwater samples and direct on-site and in-situ detection of Hg2+ in contaminated groundwater, achieving acceptable results. Furthermore, NXS@ZIF-8 was fabricated as a paper-based sensor and integrated into a portable smartphone device for visual detection of Hg2+ in contaminated groundwater. This work presents an approach for on-site, in-situ and highly sensitive portable detection of heavy metals in contaminated groundwater, eliminating the need for access to specialized laboratory equipment.

Polydopamine-Coated Copper-Doped Mesoporous Silica/Gelatin-Waterborne Polyurethane Composite: A Multifunctional GBR Membrane Bone Defect Repair

Guided bone regeneration (GBR) membrane has proven to be a fundamental tool in the realm of bone defect repair. In this study, we develop a mussel-inspired composite biomaterial through polydopamine-assisted, combining gelatin-WPU matrix with the ion-release behavior of Cu-MSNs for augmented bone regeneration. The optimized composite membrane exhibits enhanced mechanical stability, demonstrating a tensile strength of 11.23 MPa (representing a 2.3-fold increase compared to Bio-Gide®), coupled with significantly slower degradation kinetics that retained 73.3% structural integrity after 35-day immersion in physiological solution. Copper ions act as angiogenic agents to promote blood vessel growth and as antimicrobial agents to prevent potential infections. The combined effect of these components creates a biomimetic environment that is ideal for cell adhesion, growth, and differentiation. This research significantly contributes to the development of advanced biomaterials that combine regeneration and infection-prevention functions. It provides a versatile and effective solution for treating bone injuries and defects, offering new hope for patients in need.

Coarse-Grained Modeling of a Metal-Organic Framework/Polymer Composite and Its Gas Adsorption at the Nanoparticle Level

Simulations have acted as a cornerstone to understand the MOF/polymer interface structure; however, no molecular-level simulation has yet been performed at the nanoparticle scale. In this work, a hybrid MARTINI/force matching (FM) force field was developed and successfully implemented to model the ZIF-8/PVDF composite at a coarse-grained resolution. Interphase interactions were modeled using FM potentials, which strive to reasonably reproduce the forces from an atomistic benchmark model, while intraphase interactions were modeled using the general-purpose MARTINI potentials. Systems made of a ZIF-8 nanoparticle embedded into a PVDF matrix were considered to evaluate the effect of nanoparticle size and morphology in the polymer structuration and in the CO2 adsorption. Results show that simulations at the nanoparticle level are crucial for depicting polymer penetration. Notably, the smallest nanoparticle exhibited the least extent of polymer penetration, while the cubic nanoparticle exhibited the highest amount. Polymer conformation and local density values change following the same trend in all ZIF-8/PVDF systems depending on whether the polymer lies inside or outside the nanoparticle domain. All composite models present more significant CO2 adsorption in the nanoparticle domain than in the PVDF phase, in agreement with experiments. More remarkably, the small rhombic dodecahedron ZIF-8/PVDF system presents a larger equilibrium amount of gas adsorbed at ambient conditions compared to the other two systems, in alignment with the observed polymer penetration trend. On the other hand, comparison of CO2 adsorption capacities in cubic and rhombic dodecahedron ZIF-8 nanoparticles of similar sizes reveals that the former is more advantageous for CO2 adsorption.

Engineering ZIF-8@Ag core-satellite superstructures through solvent-induced tunable self-assembly for surface-enhanced Raman spectroscopy

Metal-organic framework (MOF) based substrates have great potential for quantitative analysis of hazardous substances using surface-enhanced Raman spectroscopy (SERS) due to their significant signal enhancement, but face challenges like complex preparation, and lack of tunability. Here, we have successfully prepared a well-defined core-satellite superstructure (ZIF-8@Ag) through solvent-induced assembly of silver nanoparticles (Ag NPs) on truncated rhombic dodecahedral ZIF-8. By wisely selecting toluene as the solvent, the assembly process can be easily initiated through ultrasonic treatment and it allows for precise morphological adjustments to build a range of superstructures with different assembly densities of Ag NPs via feed ratio tuning. The as-prepared ZIF-8@Ag substrate leverages the high-density distribution of Ag NPs and the exceptional adsorption capabilities of ZIF-8. This combination makes it an outstanding SERS substrate for the detection of crystal violet (CV) and methylene blue (MB), achieving a concentration as low as 1 × 10-10 M and 1 × 10-9 M, respectively. Moreover, the Raman analytical enhancement factor (AEF) of this ZIF-8@Ag substrate can reach 1.35 × 107, and the Raman signals exhibited high homogeneity. These findings are essential for constructing complex structures and achieving better performance in SERS enhancement substrates, which can broaden the application of this technology in other fields.

Controllable Design of Polyamide Composite Membrane Separation Layer Structures via Metal-Organic Frameworks: A Review

Optimizing the structure of the polyamide (PA) layer to improve the separation performance of PA thin-film composite (TFC) membranes has always been a hot topic in the field of membrane preparation. As novel crystalline materials with high porosity, multi-functional groups, and good compatibility with membrane substrate, metal-organic frameworks (MOFs) have been introduced in the past decade for the modification of the PA structure in order to break through the separation trade-off between permeability and selectivity. This review begins by summarizing the recent progress in the control of MOF-based thin-film nanocomposite (TFN) membrane structures. The review also covers different strategies used for preparing TFN membranes. Additionally, it discusses the mechanisms behind how these strategies regulate the structure and properties of PA. Finally, the design of a competent MOF material that is suitable to reach the requirements for the fabrication of TFN membranes is also discussed. The aim of this paper is to provide key insights into the precise control of TFN-PA structures based on MOFs.

Nanomaterials-modified reverse osmosis membranes: a comprehensive review

Because of its great efficiency and widespread application, reverse osmosis (RO) is a popular tool for water desalination and purification. However, traditional RO membranes have a short lifespan due to membrane fouling, deterioration, decreased salt rejection rate, and the low water flux with aging. As a result, membrane modification has received a lot of attention recently, with nanomaterials being extensively researched to improve membrane efficacy and lifespan. Herein, we present an in-depth analysis of recent advances of RO membranes modification utilizing nanomaterials. An overview of the various nanomaterials used for membrane modification, including metal oxides, zeolites, and carbon nanomaterials, is provided. The synthesis techniques and methods of integrating these nanomaterials into RO membranes are also discussed. The impacts of nanomaterial change on the performance of RO membranes are addressed. The underlying mechanisms responsible for RO membrane enhancements by nanomaterials, such as improved surface hydrophilicity, reduced membrane fouling via surface repulsion and anti-adhesion properties, and enhanced structural stability, are discussed. Furthermore, the review provides a critical analysis of the challenges and limitations associated with the use of nanomaterials to modify RO membranes. Overall, this review provides valuable insights into the modification of RO membranes with nanomaterials, providing a full grasp of the benefits, challenges, and future prospects of this challenging topic.

Thin Film Nanocomposite Membranes Based on Zeolitic Imidazolate Framework-8/Halloysite Nanotube Composites

Thin film nanocomposite (TFN) membranes have proven their unrivaled value, as they can combine the advantages of different materials and furnish membranes with improved selectivity and permeability. The development of TFN membranes has been severely limited by the poor dispersion of the nanoparticles and the weak adhesion between the nanoparticles and the polymer matrix. In this study, to address the poor dispersion of nanoparticles in TFN membranes, we proposed a new combination of m-ZIF-8 and m-HNTs, wherein the ZIF-8 and HNTs were modified with poly (sodium p-styrenesulfonate) to enhance their dispersion in water. Furthermore, the hydropathic properties of the membranes can be well controlled by adjusting the content of m-ZIF-8 and m-HNTs. A series of modified m-ZIF-8/m-HNT/PAN membranes were prepared to modulate the dye/salt separation performance of TFN membranes. The experimental results showed that our m-ZIF-8/m-HNT/PAN membranes can elevate the water flux significantly up to 42.6 L m-2 h-1 MPa-1, together with a high rejection of Reactive Red 49 (more than 80%). In particular, the optimized NFM-7.5 membrane that contained 7.5 mg of HNTs and 2.5 mg of ZIF-8 showed a 97.1% rejection of Reactive Red 49 and 21.3% retention of NaCl.

PolyMOF nanoparticles constructed from intrinsically microporous polymer ligand towards scalable composite membranes for CO2 separation

Integrating different modification strategies into a single step to achieve the desired properties of metal-organic frameworks (MOFs) has been very synthetically challenging, especially in developing advanced MOF/polymer mixed matrix membranes (MMMs). Herein, we report a polymer-MOF (polyMOF) system constructed from a carboxylated polymer with intrinsic microporosity (cPIM-1) ligand. This intrinsically microporous ligand could coordinate with metals, leading to ~100 nm-sized polyMOF nanoparticles. Compared to control MOFs, these polyMOFs exhibit enhanced ultramicroporosity for efficient molecular sieving, and they have better dispersion properties in casting solutions to prepare MMMs. Ultimately, integrating coordination chemistries through the cPIM-1 and polymer-based functionality into porous materials results in polyMOF/PIM-1 MMMs that display excellent CO2 separation performance (surpassing the CO2/N2 and CO2/CH4 upper bounds). In addition to exploring the physicochemical and transport properties of this polyMOF system, scalability has been demonstrated by converting the developed MMM material into large-area (400 cm2) thin-film nanocomposite (TFN) membranes.

A review on artificial water channels incorporated polyamide membranes for water purification: Transport mechanisms and performance

While thin-film composite (TFC) polyamide (PA) membranes are advanced for removing salts and trace organic contaminants (TrOCs) from water, TFC PA membranes encounter a water permeance-selectivity trade-off due to PA layer structural characteristics. Drawing inspiration from the excellent water permeance and solute rejection of natural biological channels, the development of analogous artificial water channels (AWCs) in TFC PA membranes (abbreviated as AWCM) promises to achieve superior mass transfer efficiency, enabling breaking the upper bound of water permeance and selectivity. Herein, we first discussed the types and structural characteristics of AWCs, followed by summarizing the methods for constructing AWCM. We discussed whether the AWCs acted as the primary mass transfer channels in AWCM and emphasized the important role of the AWCs in water transport and ion/TrOCs rejection. We thoroughly summarized the molecular-level mechanisms and structure-performance relationship of water molecules, ions, and TrOCs transport in the confined nanospace of AWCs, which laid the foundation for illustrating the enhanced water permeance and salt/TrOCs selectivity of AWCM. Finally, we discussed the challenges encountered in the field of AWCM and proposed future perspectives for practical applications. This review is expected to offer guidance for understanding the transport mechanisms of AWCM and developing next-generation membrane for effective water treatment.

High performance forward osmosis membrane with ultrathin hydrophobic nanofibrous interlayer

The novel thin film composite (TFC) forward osmosis (FO) membrane with electrospinning nanofibers as support layer can alleviate internal concentration polarization (ICP). While the macropores of the nanofiber support layer cause defects in the polyamide (PA) layer. Therefore, hydrophobic polyvinylidene fluoride (PVDF) fine nanofibers were used as an interlayer to modulate the process of interfacial polymerization (IP) in this study. The results showed that the introduction of the interlayer improved the hydrophobicity of the support layer for achieving uniform, thin and defect-free selective polyamide (PA) layer. The water flux of TFC-PVDF was 58.26 LMH in the FO mode of 2 M NaCl, which was two times higher than that of the unmodified FO membrane. Lower reverse salt flux (4.91 gMH) and structural parameter (179.43 μm) alleviated the ICP. In addition, TFC-PVDF membrane showed good anti-fouling performance for SA (flux recovery ratio of 93.97%) due to high hydrophilicity, low zeta potential and low roughness. This study provides an easy and promising method to prepare defect-free PA selective layer on the macropores nanofiber support layer. The novel FO membrane shows high desalination performance and anti-fouling properties.

Surface Treatment of Polymer Membranes for Effective Biofouling Control

Membrane biofouling is the consequence of the deposition of microorganisms on polymer membrane surfaces. Polymeric membranes have garnered more attention for filtering and purifying water because of their ease of handling, low cost, effortless surface modification, and mechanical, chemical, and thermal properties. The sizes of the pores in the membranes enable micro- and nanofiltration, ultrafiltration, and reverse osmosis. Commonly used polymers for water filter membranes are polyvinyl chloride (PVA), polyvinylidene fluoride (PVDF), polyamide (PA), polyethylene glycol (PEG), polyethersulfone (PES), polyimide (PI), polyacrylonitrile (PAN), polyvinyl alcohol (PA), poly (methacrylic acid) (PMAA), polyaniline nanoparticles (PANI), poly (arylene ether ketone) (PAEK), polyvinylidene fluoride polysulfone (PSF), poly (ether imide) (PEI), etc. However, these polymer membranes are often susceptible to biofouling because of inorganic, organic, and microbial fouling, which deteriorates the membranes and minimizes their lives, and increases operating costs. Biofouling infection on polymer membranes is responsible for many chronic diseases in humans. This contamination cannot be eliminated by periodic pre- or post-treatment processes using biocides and other chemicals. For this reason, it is imperative to modify polymer membranes by surface treatments to enhance their efficiency and longevity. The main objective of this manuscript is to discuss application-oriented approaches to control biofouling on polymer membranes using various surface treatment methods, including nanomaterials and fouling characterizations utilizing advanced microscopy and spectroscopy techniques.

Enhanced Desulfurization Performance of ZIF-8/PEG MMMs: Effect of ZIF-8 Particle Size

Constructing efficient and continuous transport pathways in membranes is a promising and challenging way to achieve the desired performance in the pervaporation process. The incorporation of various metal-organic frameworks (MOFs) into polymer membranes provided selective and fast transport channels and enhanced the separation performance of polymeric membranes. Particle size and surface properties are strongly related to the random distribution and possible agglomeration of MOFs particles, which may lead to poor connectivity between adjacent MOFs-based nanoparticles and result in low-efficiency molecular transport in the membrane. In this work, ZIF-8 particles with different particle sizes were physically filled into PEG to fabricate mixed matrix membranes (MMMs) for desulfurization via pervaporation. The micro-structures and physi-/chemical properties of different ZIF-8 particles, along with their corresponding MMMs, were systematically characterized by SEM, FT-IR, XRD, BET, etc. It was found that ZIF-8 with different particle sizes showed similar crystalline structures and surface areas, while larger ZIF-8 particles possessed more micro-pores and fewer meso-/macro-pores than did the smaller particles. ZIF-8 showed preferential adsorption for thiophene rather than n-heptane molecules, and the diffusion coefficient of thiophene was larger than that of thiophene in ZIF-8, based on molecular simulation. PEG MMMs with larger ZIF-8 particles showed a higher sulfur enrichment factor, but a lower permeation flux than that found with smaller particles. This might be ascribed to the fact that larger ZIF-8 particles provided more and longer selective transport channels in one single particle. Moreover, the number of ZIF-8-L particles in MMMs was smaller than the number of smaller ones with the same particle loading, which might weaken the connectivity between adjacent ZIF-8-L nanoparticles and result in low-efficiency molecular transport in the membrane. Moreover, the surface area available for mass transport was smaller for MMMs with ZIF-8-L particles due to the smaller specific surface area of the ZIF-8-L particles, which might also result in lower permeability in ZIF-8-L/PEG MMMs. The ZIF-8-L/PEG MMMs exhibited enhanced pervaporation performance, with a sulfur enrichment factor of 22.5 and a permeation flux of 183.2 g/(m^-2·h^-1), increasing by 57% and 389% compared with the results for pure PEG membrane, respectively. The effects of ZIF-8 loading, feed temperature, and concentration on desulfurization performance were also studied. This work might provide some new insights into the effect of particle size on desulfurization performance and the transport mechanism in MMMs.

Correlating the Role of Nanofillers with Active Layer Properties and Performance of Thin-Film Nanocomposite Membranes

Thin-film nanocomposite (TFN) membranes are emerging water-purification membranes that could provide enhanced water permeance with similar solute removal over traditional thin-film composite (TFC) membranes. However, the effects of nanofiller incorporation on active layer physico-chemical properties have not been comprehensively studied. Accordingly, we aimed to understand the correlation between nanofillers, active layer physico-chemical properties, and membrane performance by investigating whether observed performance differences between TFN and control TFC membranes correlated with observed differences in physico-chemical properties. The effects of nanofiller loading, surface area, and size on membrane performance, along with active layer physico-chemical properties, were characterized in TFN membranes incorporated with Linde Type A (LTA) zeolite and zeolitic imidazole framework-8 (ZIF-8). Results show that nanofiller incorporation up to ~0.15 wt% resulted in higher water permeance and unchanged salt rejection, above which salt rejection decreased 0.9-25.6% and 26.1-48.3% for LTA-TFN and ZIF-8-TFN membranes, respectively. Observed changes in active layer physico-chemical properties were generally unsubstantial and did not explain observed changes in TFN membrane performance. Therefore, increased water permeance in TFN membranes could be due to preferential water transport through porous structures of nanofillers or along polymer-nanofiller interfaces. These findings offer new insights into the development of high-performance TFN membranes for water/ion separations.

Nanostructured Material and its Application in Membrane Separation Technology

Abstract:

Nanomaterials are classified with their at least one dimension in the range of 1-100 nm, which offers new innovative solutions for membrane development. These are included as nanosized adsorbents, nanomembranes, nanocomposites, photocatalysts, nanotubes, nanoclays, etc. Nanomaterials are promising, exceptional properties for one of the opportunity is to prevent the global water crisis with their extraordinary performance as their usage for membrane development, particularly for water treatment process. Nanomaterial based membranes that include nanoparticles, nanofibers, 2D layered materials, and their nanostructured composites which provide superior permeation characteristics besides their antifouling, antibacterial and photodegradation properties. They are enable for providing the extraordinary properties to be used as ultrafast and ultimately selective membranes for water purification. In this review, recently developed nanomaterial based membranes and their applications for water treatment process were summarized. The main attention is given to the nanomaterial based membrane structure design. The variety in terms of constituent structure and alterations provide nanomaterial based membranes which will be expected to be a perfect separation membrane in the future.

Task-specific polymeric membranes to achieve high gas-liquid mass transfer

In the current study, Polyimide (P84)-based polymeric membranes were fabricated and used as spargers in the bubble column reactor (BCR) to get a high gas-liquid mass transfer (GL-MT) rate of oxygen in water. Different polymeric membranes were fabricated by incorporating polyvinyl pyrrolidone (PVP) as a porogen and a Zeolitic Imidazolate Framework (ZIF-8) to induce high porosity and hydrophobicity in the membranes. The GL-MT efficiency of membranes was evaluated by measuring the overall volumetric mass transfer coefficient (k_La) of oxygen in air. The k_La of O₂ (in air) was measured by supplying the gas through a fixed membrane surface area of 11.94 cm² at a fixed gas flow rate of 3L/min under atmospheric pressure. The results revealed that adding porogen and ZIF-8 increased the porosity of the membranes compared to the pure polymeric membranes. In comparison, the ZIF-8 (3 wt%) based membrane showed the highest porosity (80%), hydrophobicity (95° contact angle) and k_La of oxygen in air (241.2 h^-1) with 78% saturation in only 60 s. ZIF-8 based membranes showed the potential to increase the amount of dissolved oxygen in BCR by reducing the bubble size, increasing the number of bubbles, and improving the hydrophobicity. The study showed that ZIF-8 based membrane diffusers are expected to produce high GL-MT in microbial syngas fermentation. To the best of our knowledge, this is the first study on the fabrication and application of polymeric membranes for GL-MT applications. Further research should be conducted under real fermentation conditions to assess the practicality of the system to support substrate utilization, microbial growth, and product formation.

Study of Membranes with Nanotubes to Enhance Osmosis Desalination Efficiency by Using Machine Learning towards Sustainable Water Management

Water resources management is one of the most important issues nowadays. The necessity of sustainable management of water resources, as well as finding a solution to the water shortage crisis, is a question of our survival on our planet. One of the most important ways to solve this problem is to use water purification systems for wastewater resources, and one of the most necessary reasons for the research of water desalination systems and their development is the problem related to water scarcity and the crisis in the world that has arisen because of it. The present study employs a carbon nanotube-containing nanocomposite to enhance membrane performance. Additionally, the rise in flow brought on by a reduction in the membrane's clogging surface was investigated. The filtration of brackish water using synthetic polyamide reverse osmosis nanocomposite membrane, which has an electroconductivity of 4000 Ds/cm, helped the study achieve its goal. In order to improve porosity and hydrophilicity, the modified raw, multi-walled carbon nanotube membrane was implanted using the polymerization process. Every 30 min, the rates of water flow and rejection were evaluated. The study's findings demonstrated that the membranes have soft hydrophilic surfaces, and by varying concentrations of nanocomposite materials in a prescribed way, the water flux increased up to 30.8 L/m²h, which was notable when compared to the water flux of the straightforward polyamide membranes. Our findings revealed that nanocomposite membranes significantly decreased fouling and clogging, and that the rejection rate was greater than 97 percent for all pyrrole-based membranes. Finally, an artificial neural network is utilized to propose a predictive model for predicting flux through membranes. The model benefits hyperparameter tuning, so it has the best performance among all the studied models. The model has a mean absolute error of 1.36% and an R² of 0.98.

Molecular modeling of thin-film nanocomposite membranes for reverse osmosis water desalination

The scarcity of freshwater resources is a major global challenge causedby population and economic growth. Water desalination using a reverse osmosis (RO) membrane is a promising technology to supply potable water from seawater and brackish water. The advancement of RO desalination highly depends on new membrane materials. Currently, the RO technology mainly relies on polyamide thin-film composite (TFC) membranes, which suffer from several drawbacks (e.g., low water permeability, permeability-selectivity tradeoff, and low fouling resistance) that hamper their real-world applications. Nanoscale fillers with specific characteristics can be used to improve the properties of TFC membranes. Embedding nanofillers into TFC membranes using interfacial polymerization allows the creation of thin-film nanocomposite (TFNC) membranes, and has become an emerging strategy in the fabrication of high-performance membranes for advanced RO water desalination. To achieve optimal design, it is indispensable to search for reliable methods that can provide fast and accurate predictions of the structural and transport properties of the TFNC membranes. However, molecular understanding of permeability-selectivity characteristics of nanofillers remains limited, partially due to the challenges in experimentally exploring microscopic behaviors of water and salt ions in confinement. Molecular modeling and simulations can fill this gap by generating molecular-level insights into the effects of nanofillers' characteristics (e.g., shape, size, surface chemistry, and density) on water permeability and ion selectivity. In this review, we summarize molecular simulations of a diverse range of nanofillers including nanotubes (carbon nanotubes, boron nitride nanotubes, and aquaporin-mimicking nanochannels) and nanosheets (graphene, graphene oxide, boron nitride sheets, molybdenum disulfide, metal and covalent organic frameworks) for water desalination applications. These simulations reveal that water permeability and salt rejection, as the major factors determining the desalination performance of TFNC membranes, significantly depend on the size, topology, density, and chemical modifications of the nanofillers. Identifying their influences and the physicochemical processes behind, via molecular modeling, is expected to yield important insights for the fabrication and optimization of the next generation high-performance TFNC membranes for RO water desalination.

Enhanced Separation Performance of Polyamide Thin-Film Nanocomposite Membranes with Interlayer by Constructed Two-Dimensional Nanomaterials: A Critical Review

Thin-film composite (TFC) polyamide (PA) membrane has been widely applied in nanofiltration, reverse osmosis, and forward osmosis, including a PA rejection layer by interfacial polymerization on a porous support layer. However, the separation performance of TFC membrane is constrained by the trade-off relationship between permeability and selectivity. Although thin-film nanocomposite (TFN) membrane can enhance the permeability, due to the existence of functionalized nanoparticles in the PA rejection layer, the introduction of nanoparticles leads to the problems of the poor interface compatibility and the nanoparticles agglomeration. These issues often lead to the defect of PA rejection layers and reduction in selectivity. In this review, we summarize a new class of structures of TFN membranes with functionalized interlayers (TFNi), which promises to overcome the problems associated with TFN membranes. Recently, functionalized two-dimensional (2D) nanomaterials have received more attention in the assembly materials of membranes. The reported TFNi membranes with 2D interlayers exhibit the remarkable enhancement on the permeability, due to the shorter transport path by the "gutter mechanism" of 2D interlayers. Meanwhile, the functionalized 2D interlayers can affect the diffusion of two-phase monomers during the interfacial polymerization, resulting in the defect-free and highly crosslinked PA rejection layer. Thus, the 2D interlayers enabled TFNi membranes to potentially overcome the longstanding trade-off between membrane permeability and selectivity. This paper provides a critical review on the emerging 2D nanomaterials as the functionalized interlayers of TFNi membranes. The characteristics, function, modification, and advantages of these 2D interlayers are summarized. Several perspectives are provided in terms of the critical challenges for 2D interlayers, managing the trade-off between permeability, selectivity, and cost. The future research directions of TFNi membranes with 2D interlayers are proposed.

Facile monomer interlayered MOF based thin film nanocomposite for efficient arsenic separation

The thin film nanocomposites (TFN) based membranes are sensitive to the synergy between the polymer and nanoparticles. TFN incorporating metal-organic frameworks (MOFs) have shown tremendous enhancement in permeability. This study investigates alternate MOF positioning during TFC fabrication for a highly selective membrane. Co-Zn-based mixed metal-organic framework (mMOF) was interlayered between m-phenylenediamine (MPD) and trimesoyl chloride (TMC) to form a polyamide (PA) selective layer. The practiced method conveniently allowed exact loading of mMOF and thus prevented the loss. Owing to the mMOF's placement between MPD and TMC, an increase in PA cross-linking was observed. The mMOF-MPD monomer compatibility allowed homogeneous distribution and formation of a defect-free PA layer. The surface morphology showed a more pronounced formation of leaves-like features due to interfacial degassing. Neutral solute-based filtration tests determined mean pore size, probability distribution, and MWCO. The incorporation of mMOF led to formation of additional nanochannels in the membrane surface. The perm-selectivity studies performed on a dead-end filtration unit resulted in 94% As⁵⁺ retention with 2.5 times higher permeance than the control. The current study pronounced the viability of the monomer interlayer method to form a highly selective TFN for water separation and related applications.

Fabrication of Thin Film Composite Membranes on Nanozeolite Modified Support Layer for Tailored Nanofiltration Performance

Thin-film composite (TFC) structure has been widely employed in polymeric membrane fabrication to achieve superior performance for desalination and water treatment. In particular, TFC membranes with a thin active polyamide (PA) selective layer are proven to offer improved permeability without compromising salt rejection. Several modifications to TFCs have been proposed over the years to enhance their performance by altering the selective, intermediate, or support layer. This study proposes the modification of the membrane support using nanozeolites prepared by a unique ball milling technique for tailoring the nanofiltration performance. TFC membranes were fabricated by the interfacial polymerization of Piperazine (PIP) and 1,3,5-Benzenetricarbonyl trichloride (TMC) on Polysulfone (PSf) supports modified with nanozeolites. The nanozeolite concentration in the casting solution varied from 0 to 0.2%. Supports prepared with different nanozeolite concentrations resulted in varied hydrophilicity, porosity, and permeability. Results showed that optimum membrane performance was obtained for supports modified with 0.1% nanozeolites where pure water permeance of 17.1 ± 2.1 Lm^-2 h^-1 bar^-1 was observed with a salt rejection of 11.47%, 33.84%, 94%, and 95.1% for NaCl, MgCl₂, MgSO_4, and Na₂SO₄ respectively.

Growth Pattern Control and Nanoarchitecture Engineering of Metal-Organic Framework Single Crystals by Confined Space Synthesis

The nanoarchitecture engineering of metal-organic frameworks (MOFs) is a fascinating but intellectually challenging concept that opens up avenues for both tailoring the properties of MOFs and expanding their applications. Herein, we report the confined growth of ZIF-8 single crystals in a three-dimensionally ordered (3DO) macroporous polystyrene replica and reveal that their growth patterns, morphologies, and nanoarchitectures can be highly engineered using the concentration of the precursor. Impressively, the favorable in situ confined growth enables the successful fabrication of 3DO sphere-assembled ZIF-8 single crystals or 3DO single-crystalline ZIF-8 sphere arrays when a low- or high-concentration precursor solution, respectively, is used as the feedstock. Furthermore, our strategy can be extended to the preparation of other 3DO MOF single crystals, including ZIF-67 and HKUST-1, with similar controllable hierarchical nanoarchitectures. With the successful preparation of a series of diameter-tunable ZIF-8 single-crystalline spheres, we further unravel their interesting size-performance relationship in the Knoevenagle reaction between benzaldehyde and malononitrile, wherein the smallest spheres show the fastest first-order reaction kinetics. This study not only develops a general strategy for engineering the nanoarchitectures of MOF single crystals but also provides fundamental knowledge of the mechanism for the growth of hierarchical single crystals under confined spaces.

Capillary-Assisted Fabrication of Thin-Film Nanocomposite Membranes for Improved Solute-Solute Separation

Efficient separation of harmful contaminants (e.g., per- and polyfluoroalkyl substances, PFASs) from valuable components (water and nutrients) is essential to the resource recovery from domestic wastewater for agricultural purposes. Such selective recovery requires precise separation at the angstrom scale. Although nanofiltration (NF) has the potential to achieve solute-solute separation, the state-of-the-art polyamide (PA) membranes are typically constrained by limited precision of solute-solute selectivity and their well-documented permeability-selectivity trade-off. Herein, we present a novel capillary-assisted interfacial polymerization (CAIP) approach to generate metal-organic framework (MOF)-PA nanocomposite membranes with reduced surface charges and more uniform pore sizes that favor solute selectivity by enhanced size exclusion. By uniquely regulating the PA-MOF interactions using the capillary force, CAIP results in effective exposure of MOF nanochannels on the membrane surface and a PA matrix with a high cross-linking gradient in the vertical direction, both of which contribute to an exceptional water permeance of ∼18.7 LMH/bar and an unprecedentedly high selectivity between nutrient ions and PFASs. Our CAIP approach breaks new ground for utilizing nanoparticles with nanochannels in fabricating the next-generation, fit-for-purpose NF membranes for improved solute-solute separations.

Surface Modification of Matrimid® 5218 Polyimide Membrane with Fluorine-Containing Diamines for Efficient Gas Separation

Polyimide membranes have been widely investigated in gas separation applications due to their high separation abilities, excellent processability, relatively low cost, and stabilities. Unfortunately, it is extremely challenging to simultaneously achieve both improved gas permeability and selectivity due to the trade-off relationship in common polymer membranes. Diamine modification is a simple strategy to tune the separation performance of polyimide membranes, but an excessive loss in permeability is also generally observed. In the present work, we reported the effects of diamine type (i.e., non-fluorinated and fluorinated) on the physicochemical properties and the corresponding separation performance of a modified membrane using a commercial Matrimid® 5218 polyimide. Detailed spectroscopic, thermal, and surface analyses reveal that the bulky fluorine groups are responsible for the balanced chain packing modes in the resulting Matrimid membranes compared to the non-fluorinated diamines. Consequently, the modified Matrimid membranes using fluorinated diamines exhibit both higher gas permeability and selectivity than those of pristine Matrimid, making them especially effective for improving the separation performance towards H2/CH4 and CO2/CH4 pairs. The results indicate that the use of fluorinated modifiers may offer new opportunities to tune the gas transport properties of polyimide membranes.

Desalination Characteristics of Cellulose Acetate FO Membrane Incorporated with ZIF-8 Nanoparticles

Forward osmosis membranes have a wide range of applications in the field of water treatment. However, the application of seawater desalination is restricted, so the research of forward osmosis membranes for seawater desalination poses new challenges. In this study, zeolitic imidazolate framework-8 (ZIF-8) was synthesized by a mechanical stirring method, and its crystal structure, surface morphology, functional group characteristics, thermochemical stability, pore size distribution and specific surface area were analyzed. The cellulose acetate (CA)/ZIF-8 mixed matrix forward osmosis membrane was prepared by using the synthesized ZIF-8 as a modified additive. The effects of the additive ZIF-8 content, coagulation bath temperature, mixing temperature and heat treatment temperature on the properties of the CA/ZIF-8 forward osmosis membrane were systematically studied, and the causes were analyzed to determine the best membrane preparation parameters. The structure of the CA membrane and CA/ZIF-8 mixed matrix forward osmosis membranes prepared under the optimal conditions were characterized by Fourier Transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), contact angle and Atomic force microscope (AFM). Finally, the properties of the HTI membrane (Membrane manufactured by Hydration Technology Innovations Inc.), CA forward osmosis membrane and CA/ZIF-8 mixed matrix forward osmosis membrane were compared under laboratory conditions. For the CA membrane, the water flux and reverse salt flux reached 48.85 L·m-2·h-1 and 3.4 g·m-2·h-1, respectively. The reverse salt flux and water flux of the CA/ZIF-8 membrane are 2.84 g·m-2·h-1 and 50.14 L·m-2·h-1, respectively. ZIF-8 has a promising application in seawater desalination.

Membrane bioreactors for hospital wastewater treatment: recent advancements in membranes and processes

Discharged hospital wastewater contains various pathogenic microorganisms, antibiotic groups, toxic organic compounds, radioactive elements, and ionic pollutants. These contaminants harm the environment and human health causing the spread of disease. Thus, effective treatment of hospital wastewater is an urgent task for sustainable development. Membranes, with controllable porous and nonporous structures, have been rapidly developed for molecular separations. In particular, membrane bioreactor (MBR) technology demonstrated high removal efficiency toward organic compounds and low waste sludge production. To further enhance the separation efficiency and achieve material recovery from hospital waste streams, novel concepts of MBRs and their applications are rapidly evolved through hybridizing novel membranes (non hydrophilic ultrafiltration/microfiltration) into the MBR units (hybrid MBRs) or the MBR as a pretreatment step and integrating other membrane processes as subsequent secondary purification step (integrated MBR-membrane systems). However, there is a lack of reviews on the latest advancement in MBR technologies for hospital wastewater treatment, and analysis on its major challenges and future trends. This review started with an overview of main pollutants in common hospital waste-water, followed by an understanding on the key performance indicators/criteria in MBR membranes (i.e., solute selectivity) and processes (e.g., fouling). Then, an in-depth analysis was provided into the recent development of hybrid MBR and integrated MBR-membrane system concepts, and applications correlated with wastewater sources, with a particular focus on hospital wastewaters. It is anticipated that this review will shed light on the knowledge gaps in the field, highlighting the potential contribution of hybrid MBRs and integrated MBR-membrane systems toward global epidemic prevention.

2D Metal-Organic Framework-Based Thin-Film Nanocomposite Membranes for Reverse Osmosis and Organic Solvent Nanofiltration

Metal-organic frameworks (MOFs) are promising candidates for membrane-based liquid separations due to their intrinsic microporosity, but many are limited by their insufficient stability. In this work, a copper-benzoquinoid (Cu-THQ) MOF was synthesized and demonstrated structural stability in water and organic solvents. After incorporation into the polyamide layer, the hydrophilicity of the membranes was enhanced. The resultant thin-film nanocomposite (TFN) membranes broke the permeability-selectivity tradeoff by showing 242 % increase in water permeance and slightly enhanced salt rejection at MOF loading of 0.0192 mg cm^-2 . The underlying mechanism was probed by different chemical and morphological characterizations. The membranes also showed improved tolerance to chlorine oxidation. With their excellent stability, the Cu-THQ MOF-based membranes further demonstrated impressive performance in organic solvent nanofiltration involving dimethylformamide.

Influence of Substitutional Defects in ZIF-8 Membranes on Reverse Osmosis Desalination: A Molecular Dynamics Study

In this study, molecular dynamics simulation is used to investigate the effects of water-based substitutional defects in zeolitic imidazolate frameworks (ZIF)-8 membranes on their reverse osmosis (RO) desalination performance. ZIF-8 unit cells containing up to three defect sites are used to construct the membranes. These substitutional defects can either be Zn defects or linker defects. The RO desalination performance of the membranes is assessed in terms of the water flux and ion rejection rate. The effects of defects on the interactions between the ZIF-8 membranes and NaCl are investigated and explained with respect to the radial distribution function (RDF) and ion density distribution. The results show that ion adsorption on the membranes occurs at either the nitrogen atoms or the defect sites. Complete NaCl rejection can be achieved by introducing defects to change the size of the pores. It has also been discovered that the presence of linker defects increases membrane hydrophilicity. Overall, molecular dynamics simulations have been used in this study to show that water-based substitutional defects in a ZIF-8 structure reduce the water flux and influence its hydrophilicity and ion adsorption performance, which is useful in predicting the type and number of defect sites per unit cell required for RO applications. Of the seven ZIF-8 structures tested, pristine ZIF-8 exhibits the best RO desalination performance.

A Comprehensive Review on Membrane Fouling: Mathematical Modelling, Prediction, Diagnosis, and Mitigation

Membrane-based separation has gained increased popularity over the past few decades, particularly reverse osmosis (RO). A major impediment to the improved performance of membrane separation processes, in general, is membrane fouling. Fouling has detrimental effects on the membrane’s performance and integrity, as the deposition and accumulation of foulants on its surface and/or within its pores leads to a decline in the permeate flux, deterioration of selectivity, and permeability, as well as a significantly reduced lifespan. Several factors influence the fouling-propensity of a membrane, such as surface morphology, roughness, hydrophobicity, and material of fabrication. Generally, fouling can be categorized into particulate, organic, inorganic, and biofouling. Efficient prediction techniques and diagnostics are integral for strategizing control, management, and mitigation interventions to minimize the damage of fouling occurrences in the membranes. To improve the antifouling characteristics of RO membranes, surface enhancements by different chemical and physical means have been extensively sought after. Moreover, research efforts have been directed towards synthesizing membranes using novel materials that would improve their antifouling performance. This paper presents a review of the different membrane fouling types, fouling-inducing factors, predictive methods, diagnostic techniques, and mitigation strategies, with a special focus on RO membrane fouling.