Diamine crosslinked anion exchange membranes based on poly(vinyl benzyl methylpyrrolidinium) for alkaline water electrolysis

Development and Evaluation of Butyl Norbornene Based Cross-Linked Anion Exchange Membranes for Enhanced Nonaqueous Redox Flow Battery Efficiency

Nonaqueous redox flow batteries (NARFBs) have been plagued by the lack of appropriate separators to prevent crossover. In this article, the synthesis and characterization of poly(norbornene) (PNB) anion-exchange membranes (AEMs) were studied. PNB is a copolymer of butyl norbornene (BuNB) and bromobutyl norbornene (BrBuNB) with varying amounts of tetramethyl hexadiamine cross-linker. The performance of the AEMs was investigated in nonaqueous redox flow batteries under ideal conditions. Performance evaluation encompassed several key factors, including durability in a nonaqueous solvent, charge-carrying ions permeability, electric cell resistance, crossover of redox-active molecules, and mechanical properties. The BuNB-based AEMs outperformed the commercial Fumasep membrane in battery cycling tests, showcasing their superior performance characteristics. Long-term performance tests showed that the top performing PNB membrane exhibited an impressive 83% total capacity retention over 1000 charge/discharge cycles. The low loss was primarily due to minimal crossover. In contrast, the FAPQ-375 commercial membrane experienced significantly lower capacity retention, measuring only 28%, due to high crossover.

Poly(Dibenzothiophene-Terphenyl Piperidinium) for High-Performance Anion Exchange Membrane Water Electrolysis

The anion exchange membrane water electrolysis is widely regarded as the next-generation technology for producing green hydrogen. The OH- conductivity of the anion exchange membrane plays a key role in the practical implementation of this device. Here, we present a series of Z-S-x membranes with dibenzothiophene groups. These membranes contain sulfur-enhanced hydrogen bond networks that link surrounding surface site hopping regions, forming continuous OH- conducting highways. Z-S-20 has a high through-plane OH- conductivity of 182±28 mS cm-1 and ultralong stability of 2650 h in KOH solution at 80 °C. Based on rational design, we achieved a high PGM-free alkaline water electrolysis performance of 7.12 A cm-2 at 2.0 V in a flow cell and demonstrated durability of 650 h at 2 A cm-2 at 40 °C with a cell voltage increase of 0.65 mV/h.

Translating the Optimized Durability of Co-Based Anode Catalyst into Sustainable Anion Exchange Membrane Water Electrolysis

Development of robust electrocatalysts for the oxygen evolution reaction (OER) underpins the efficient production of green hydrogen via anion exchange membrane water electrolysis (AEMWE). This study elucidates the factors contributing to the degradation of cobalt-based (Co-based) OER catalysts synthesized via electrodeposition, thus establishing strategic approaches to enhance their longevity. Systematic variations in the electroplating process and subsequent heat treatment reveal a delicate balance between catalytic activity and durability, substantiated by comprehensive electrochemical assessments and material analyses. Building upon these findings, the Co-based anode is successfully optimized in the AEMWE single-cell configuration, showcasing an average degradation rate of 0.07 mV h-1 over a continuous operation for 1500 h at a current density of 1 A cm-2.

Realizing the Tailored Catalytic Performances on Atomic Pt-Promoted Transition Metal Moieties Implanted Layered Double Hydroxides for Water Electrolysis

High-performance production of green hydrogen gas is necessary to develop renewable energy generation technology and to safeguard the living environment. This study reports a controllable engineering approach to tailor the structure of nickel-layered double hydroxides via doped and absorbed platinum single atoms (PtSA) promoted by low electronegative transition metal (Mn, Fe) moieties (PtSA-Mn,Fe-Ni LDHs). We explore that the electron donation from neighboring transition metal moieties results in the well-adjusted d-band center with the low valence states of PtSA(doped) and PtSA(ads.), thus optimizing adsorption energy to effectively accelerate the H2 release. Meanwhile, a tailored local chemical environment on transition metal centers with unique charge redistribution and high valence states functions as the main center for H2O catalytic dissociation into oxygen. Therefore, the PtSA-Mn,Fe-Ni LDH material possesses a small overpotential of 42 and 288 mV to reach 10 mA·cm-2 for hydrogen and oxygen evolution, respectively, superior to most reported LDH-based catalysts. Additionally, the mass activity of PtSA-Mn,Fe-Ni LDHs proves to be 15.45 times higher than that of commercial Pt-C. The anion exchange membrane electrolyzer stack of PtSA-Mn,Fe-Ni LDHs(+,-) delivers a cell voltage of 1.79 V at 0.5 A·cm-2 and excellent durability over 600 h. This study presents a promising electrocatalyst for a practical water splitting process.

Separators and Membranes for Advanced Alkaline Water Electrolysis

Traditionally, alkaline water electrolysis (AWE) uses diaphragms to separate anode and cathode and is operated with 5-7 M KOH feed solutions. The ban of asbestos diaphragms led to the development of polymeric diaphragms, which are now the state of the art material. A promising alternative is the ion solvating membrane. Recent developments show that high conductivities can also be obtained in 1 M KOH. A third technology is based on anion exchange membranes (AEM); because these systems use 0-1 M KOH feed solutions to balance the trade-off between conductivity and the AEM's lifetime in alkaline environment, it makes sense to treat them separately as AEM WE. However, the lifetime of AEM increased strongly over the last 10 years, and some electrode-related issues like oxidation of the ionomer binder at the anode can be mitigated by using KOH feed solutions. Therefore, AWE and AEM WE may get more similar in the future, and this review focuses on the developments in polymeric diaphragms, ion solvating membranes, and AEM.

Biobased Interpenetrating Polymer Network Membranes for Sustainable Molecular Sieving

There is an urgent need for sustainable alternatives to fossil-based polymer materials. Through nanodomain engineering, we developed, without using toxic cross-linking agents, interpenetrating biopolymer network membranes from natural compounds that have opposing polarity in water. Agarose and natural rubber latex were consecutively self-assembled and self-cross-linked to form patchlike nanodomains. Both nano-Fourier transform infrared (nano-FTIR) spectroscopy and computational methods revealed the biopolymers' molecular-level entanglement. The membranes exhibited excellent solvent resistance and offered tunable molecular sieving. We demonstrated control over separation performance in the range of 227-623 g mol-1 via two methodologies: adjusting the molecular composition of the membranes and activating them in water. A carcinogenic impurity at a concentration of 5 ppm, which corresponds to the threshold of toxicological concern, was successfully purged at a negligible 0.56% pharmaceutical loss. The biodegradable nature of the membranes enables an environmentally friendly end-of-life phase; therefore, the membranes have a sustainable lifecycle from cradle to grave.

Ion Resource Recovery via Electrodialysis Fabricated with Poly(Arylene Ether Sulfone)-Based Anion Exchange Membrane in Organic Solvent System

Ion resource recovery from organic wastewater is beneficial for achieving emission peaks and carbon neutrality targets. Advanced organic solvent-resistant anion exchange membranes (AEMs) for treating organic wastewater via electrodialysis (ED) are of significant interest. Herein, a kind of 3D network AEM based on poly(arylene ether sulfone) cross-linked with a flexible cross-linker (DBH) for ion resource recovery via ED in organic solvent system is reported. Investigations demonstrate that the as-prepared AEMs show excellent dimensional stability in 60% DMSO (aq.), 60% ethanol (aq.), and 60% acetone (aq.), respectively. For example, the optimized AEM shows very low swelling ratios of 1.04-1.10% in the organic solvents. ED desalination ratio can reach 99.1% after exposure of the AEM to organic solvents for 30 days, and remain > 99% in a mixture solution containing organic solvents and 0.5 m NaCl. Additionally, at a current density of 2.5 mA cm-2, the optimized AEM soaked in organic solvents for 30 days shows a high perm-selectivity (Cl-/SO4 2-) of 133.09 (vs 13.11, Neosepta ACS). The superior ED performance is attributed to the stable continuous sub-nanochannels within AEM confirmed by SAXS, rotational energy barriers, etc. This work shows the potential application of cross-linked AEMs for resource recovery in organic wastewater.

N-Methylquinuclidinium-Based Anion Exchange Membrane with Ultrahigh Alkaline Stability

Anion-exchange-membrane (AEM) water electrolysis is a promising technology for hydrogen production from renewable energy sources. However, the bottleneck of its development is the poor comprehensive performance of AEM, especially the stability at highly concentrated alkaline condition and temperature. Herein, a new cationic group N-methylquinuclidinium with enhanced alkaline stability is proposed and hereby a full-carbon chain poly(aryl quinuclidinium) AEM is prepared. Compared with reported AEMs, it shows ultrahigh comprehensive alkaline stability (no chemical decomposition, no decay of conductivity) in 10 m NaOH aqueous solution at 80 °C for more than 1800 h, excellent dimensional stability (swelling ratio: <10% in pure water, <2% in 10 m NaOH) in OH- form at 80 °C, high OH- conductivity (≈139.1 mS cm-1 at 80 °C), and high mechanical properties (tensile strength: 41.5 MPa, elongation at break: 50%). The water electrolyzer using the AEM exhibits a high current density (1.94 A cm-2 at 2.0 V) when assembled with nickel-alloy foam electrodes, and high durability when assembled with nickel foam electrodes.

Tuning Alkaline Anion Exchange Membranes through Crosslinking: A Review of Synthetic Strategies and Property Relationships

Alkaline anion exchange membranes (AAEMs) are an enabling component for next-generation electrochemical devices, including alkaline fuel cells, water and CO2 electrolyzers, and flow batteries. While commercial systems, notably fuel cells, have traditionally relied on proton-exchange membranes, hydroxide-ion conducting AAEMs hold promise as a method to reduce cost-per-device by enabling the use of non-platinum group electrodes and cell components. AAEMs have undergone significant material development over the past two decades; however, challenges remain in the areas of durability, water management, high temperature performance, and selectivity. In this review, we survey crosslinking as a tool capable of tuning AAEM properties. While crosslinking implementations vary, they generally result in reduced water uptake and increased transport selectivity and alkaline stability. We survey synthetic methodologies for incorporating crosslinks during AAEM fabrication and highlight necessary precautions for each approach.

Crosslinked Polynorbornene-Based Anion Exchange Membranes with Perfluorinated Branch Chains

To investigate the effect of perfluorinated substituent on the properties of anion exchange membranes (AEMs), cross-linked polynorbornene-based AEMs with perfluorinated branch chains were prepared via ring opening metathesis polymerization, subsequent crosslinking reaction, and quaternization. The crosslinking structure enables the resultant AEMs (CFnB) to exhibit a low swelling ratio, high toughness, and high water uptake, simultaneously. In addition, benefiting from the ion gathering and side chain microphase separation caused by their flexible backbone and perfluorinated branch chain, these AEMs had high hydroxide conductivity up to 106.9 mS cm^-1 at 80 °C even at low ion content (IEC < 1.6 meq g^-1). This work provides a new approach to achieve improved ion conductivity at low ion content by introducing the perfluorinated branch chains and puts forward a referable way to prepare AEMs with high performance.

Pyrrolidinium-Based Hyperbranched Anion Exchange Membranes with Controllable Microphase Separated Morphology for Alkaline Fuel Cells

It is well acknowledged that the microphase-separated morphology of anion exchange membranes (AEMs) is of vital importance for membrane properties utilized in alkaline fuel cells. Herein, a rigid macromolecule poly(methyldiallylamine) (PMDA) is incorporated to regulate the microphase morphology of hyperbranched AEMs. As expected, the hyperbranched poly(vinylbenzyl chloride) (HB-PVBC) is guided to distribute along PMDA chains, and longer PMDA cha leads to a more distinct microphase morphology with interconnected ionic channels. Consequently, high chloride conductivity of 10.49 mS cm^-1 at 30 °C and suppressed water swelling ratio lower than 30% at 80 °C are obtained. Furthermore, the β-H of pyrrolidinium cations in the non-antiperiplanar position increases the energy barrier of β-H elimination, leading to conformationally disfavored Hofmann elimination and increased alkaline stability. This strategy is anticipated to provide a feasible way for preparing hyperbranched AEMs with clear microphase morphology and good overall properties for alkaline fuel cells.

Anion-exchange membrane water electrolyzers and fuel cells

The key components, working management, and operating techniques of anion-exchange membrane water electrolyzers and fuel cells are reviewed for the first time.