The optimum zinc content in set calcium phosphate cement for promoting bone formation in vivo

MgO-enhanced β-TCP promotes osteogenesis in both in vitro and in vivo rat models

Allogeneic bone grafts are used to treat bone defects in orthopedic surgery, but the osteogenic potential of artificial bones remains a challenge. In this study, we developed a β-tricalcium phosphate (β-TCP) formulation containing MgO, ZnO, SrO, and SiO2 and compared its bone-forming ability with that of β-TCP without biological elements. We prepared β-TCP discs with 60% porosity containing 1.0 wt% of these biological elements. β-TCP scaffolds were loaded with bone marrow-derived mesenchymal stem cells (BMSC) from 7-week-old male rats and cultured for 2 weeks. ALP activity and mRNA expression of osteogenic markers were evaluated. In addition, scaffolds were implanted subcutaneously in rats and analyzed after 7 weeks. In vitro, the MgO group showed lower Ca concentrations and higher osteogenic marker expression compared to controls. In vivo, the MgO group showed higher ALP activity compared to controls, and RT-qPCR analysis showed significant expression of BMP2 and VEGF. Histopathology, fluorescent immunostaining, and micro-CT also showed relatively better bone formation in the MgO group. β-TCP with MgO may enhance bone morphology in vitro and in vivo and improve the prognosis of patients with substantial and refractory bone defects.

Proteomics as a tool to study the osteoimmunomodulatory role of metallic ions in a sol-gel coating

The success of bone implants depends on the osteoimmunomodulatory (OIM) activity of the biomaterials in the interactions with the periimplantary tissues. Many in vitro tests have been conducted to evaluate the osteoimmunology effects of biomaterials. However, results of these tests have often been inconclusive. This study examines the properties of newly developed sol-gel coatings doped with two metal ions associated with bone regeneration, Ca and Zn. The study uses both proteomic methods and traditional in vitro assays. The results demonstrate that proteomics is an effective tool to scrutinize the OIM properties of the materials. Moreover, sol-gel coatings offer excellent base materials to evaluate the effects of metal ions on these properties. The obtained data highlight the highly tunable nature of sol-gel materials; studying the materials with different doping levels supplies valuable information on the interactions between the immune and bone-forming processes.

Calcium Phosphate Cements as Carriers of Functional Substances for the Treatment of Bone Tissue

Interest in calcium phosphate cements as materials for the restoration and treatment of bone tissue defects is still high. Despite commercialization and use in the clinic, the calcium phosphate cements have great potential for development. Existing approaches to the production of calcium phosphate cements as drugs are analyzed. A description of the pathogenesis of the main diseases of bone tissue (trauma, osteomyelitis, osteoporosis and tumor) and effective common treatment strategies are presented in the review. An analysis of the modern understanding of the complex action of the cement matrix and the additives and drugs distributed in it in relation to the successful treatment of bone defects is given. The mechanisms of biological action of functional substances determine the effectiveness of use in certain clinical cases. An important direction of using calcium phosphate cements as a carrier of functional substances is the volumetric incorporation of anti-inflammatory, antitumor, antiresorptive and osteogenic functional substances. The main functionalization requirement for carrier materials is prolonged elution. Various release factors related to the matrix, functional substances and elution conditions are considered in the work. It is shown that cements are a complex system. Changing one of the many initial parameters in a wide range changes the final characteristics of the matrix and, accordingly, the kinetics. The main approaches to the effective functionalization of calcium phosphate cements are considered in the review.

Enhanced osteogenesis and angiogenesis of biphasic calcium phosphate scaffold by synergistic effect of silk fibroin coating and zinc doping

Biphasic calcium phosphate (BCP) scaffold has been widely applied to bone regeneration because of its good biocompatibility and bone conduction property. However, the low mechanical strength and the lack of angiogenic and osteogenic induction properties have restricted its application in bone tissue regeneration. In this study, we combined zinc (Zn²⁺) doping and silk fibroin (SF) coating with expectation to enhance compressive strength, osteogenesis and angiogenesis of BCP scaffolds. The phase composition, morphology, porosity, compressive strength, in vitro degradation and cell behaviors were investigated systematically. Results showed that the scaffold coated with SF exhibited almost 3 times of compressive strength without compromising its porosity compared with the uncoated scaffold. Zn²⁺ doping and SF coating synergistically enhanced the alkaline phosphatase activity and osteogenesis-related genes expression of mouse bone mesenchymal stem cells (mBMSCs). Furthermore, SF coating notably improved the proliferation, cell viability and in vitro angiogenesis of human umbilical vein endothelial cells (HUVECs). This work provides a novel way to modify BCP scaffolds simultaneously with enhancing mechanical strength and biological properties.

The Development Tendency of 3D-Printed Bioceramic Scaffolds for Applications Ranging From Bone Tissue Regeneration to Bone Tumor Therapy

Three-dimensional (3D) printing concept has been successfully employed in regenerative medicine to achieve individualized therapy due to its benefit of a rapid, accurate, and predictable production process. Traditional biocomposites scaffolds (SCF) are primarily utilised for bone tissue engineering; nevertheless, over the last few years, there has already been a dramatic shift in the applications of bioceramic (BCR) SCF. As a direct consequence, this study focused on the structural, degeneration, permeation, and physiological activity of 3D-printed BCR (3DP-B) SCF with various conformations and work systems (macros, micros, and nanos ranges), as well as their impacts on the mechanical, degeneration, porosity, and physiological activities. In addition, 3DP-B SCF are highlighted in this study for potential uses applied from bone tissue engineering (BTE) to bone tumor treatment. The study focused on significant advances in practical 3DP-B SCF that can be utilized for tumor treatment as well as bone tissue regeneration (BTR). Given the difficulties in treating bone tumors, these operational BCR SCF offer a lot of promise in mending bone defects caused by surgery and killing any remaining tumor cells to accomplish bone tumor treatment. Furthermore, a quick assessment of future developments in this subject was presented. The study not only summarizes recent advances in BCR engineering, but it also proposes a new therapeutic strategy focused on the extension of conventional ceramics' multifunction to a particular diagnosis.

Improved cytocompatibility and antibacterial properties of zinc-substituted brushite bone cement based on β-tricalcium phosphate

For bone replacement materials, osteoconductive, osteoinductive, and osteogenic properties are desired. The bacterial resistance and the need for new antibacterial strategies stand among the most challenging tasks of the modern medicine. In this work, brushite cements based on powders of Zinc (Zn) (1.4 wt%) substituted tricalcium phosphate (β-TCP) and non-substituted β-TCP were prepared and investigated. Their initial and final phase composition, time of setting, morphology, pH evolution, and compressive strength are reported. After soaking for 60 days in physiological solution, the cements transformed into a mixture of brushite and hydroxyapatite. Antibacterial activity of the cements against Enterococcus faecium, Escherichia coli, and Pseudomonas aeruginosa bacteria strains was attested. The absence of cytotoxicity of cements was proved for murine fibroblast NCTC L929 cells. Moreover, the cell viability on the β-TCP cement containing Zn²⁺ ions was 10% higher compared to the β-TCP cement without zinc. The developed cements are perspective for applications in orthopedics and traumatology.

Silicate/zinc-substituted strontium apatite coating improves the osteoinductive properties of β-tricalcium phosphate bone graft substitute

Background

β-Tricalcium phosphate (β-TCP) is a popular synthetic bone graft substitute with excellent osteoconductive properties and bioabsorbability. However, its osteoinductive properties are inferior to those of autologous or allogeneic bone. Trace elements such as strontium (Sr), silica (Si), and zinc (Zn) have been reported to promote osteogenesis in materials. In this study, we aimed to determine whether a Si/Zn-substituted Sr apatite coating of β-TCP could enhance osteoinductive properties.

Methods

The apatite-coated β-TCP disks were prepared using nanoparticle suspensions of silicate-substituted Sr apatite (SrSiP) or silicate- and Zn-co-substituted Sr apatite (SrZnSiP).

Bone marrow mesenchymal cells (BMSCs) from rat femur were cultured and subsequently seeded at a density of 1.0 × 10⁶/cm² onto apatite-coated and non-coated β-TCP disks.

In vitro, the β-TCP disks were then placed in osteogenic medium, and lactate dehydrogenase (LDH) activity was measured from supernatants after culture for 2 days. Additionally, after culture for 14 days, the mRNA expression of genes encoding osteocalcin (OC), alkaline phosphatase (ALP), bone morphogenetic protein-2 (BMP-2), and vascular endothelial growth factor (VEGF) was evaluated by qRT-PCR. In vivo, the β-TCP disks were transplanted subcutaneously into rats that were sacrificed after 4 weeks. Then, the harvested disks were evaluated biochemically (ALP activity, OC content, mRNA expression of OC, ALP, BMP-2, and VEGF measured by qRT-PCR), radiologically, and histologically.

Results

Significantly higher mRNA expression of almost all evaluated osteogenic and angiogenic genes was observed in the SrZnSiP and SrSiP groups than in the non-coated group, with no significant cytotoxicity elicited by the apatite coating in vitro. Moreover, in vivo, the SrZnSiP and SrSiP groups showed significantly higher osteogenic and angiogenic gene expression and higher ALP activity and OC content than the non-coated group (P < 0.05). Radiological and histopathological findings revealed abundant bone formation in the apatite-coated group.

Conclusions

Our findings indicate that apatite coating of β-TCP improves osteoinductive properties without inducing significant cytotoxicity.

A Novel Fast-Setting Strontium-Containing Hydroxyapatite Bone Cement With a Simple Binary Powder System

In recent years, strontium-substituted calcium phosphate bone cement (Sr-CPC) has attracted more and more attentions in the field of bone tissue repair due to its comprehensive advantages of both traditional CPC and Sr ions. In this study, a crucial Sr-containing α-Ca_{3 - x} Sr _x (PO₄)₂ salt has been synthesized using a simplified one-step method at lower synthesis temperature. A novel Sr-CPC has been developed based on the simple binary Sr-containing α-Ca_{3 - x} Sr _x (PO₄)₂/Ca₄(PO₄)₂O cement powder. The physicochemical properties and hydration mechanism of this Sr-CPC at various Sr contents were intensively investigated. The setting product of this Sr-CPC after a set for 72 h is a single-phase Sr-containing hydroxyapatite, and its compressive strength slightly decreased and its setting time extended with the increase of Sr content. The hydration process included the initial formation of the medium product CaHPO₄⋅2H₂O (30 min∼1 h), the following complete hydration of Ca₄(PO₄)₂O and the initially formed CaHPO₄⋅2H₂O (2∼6 h), and the final self-setting of α-Ca_{3 - x} Sr _x (PO₄)₂ (6 h∼). The compressive strength of Sr-CPC, which was closely related to the transformation rate of Sr-containing hydroxyapatite, tended to increase with the extension of hydration time. In addition, Sr-CPC possessed favorable cytocompatibility and the effect of Sr ions on cytocompatibility of Sr-CPC was not obvious at low Sr contents. The present study suggests α-Ca_{3 - x} Sr _x (PO₄)₂ is a kind of vital Sr-containing salt source which is useful to develop some novel Sr-containing biomaterials. In addition, the new Sr-containing cement system based on this simple binary α-Ca_{3 - x} Sr _x (PO₄)₂/Ca₄(PO₄)₂O cement powder displayed an attractive clinical application potential in orthopedics.

Synthesis and properties of Sr2+ doping α-tricalcium phosphate at low temperature

Strontium has been widely used in bone repair materials due to its roles in promoting osteoclast apoptosis and enhancing osteoblast proliferation. In this work, synthesis and the effects of Sr²⁺ doping α-tricalcium phosphate at low-temperature was studied. The setting time and the mechanical properties of α-tricalcium phosphate were controlled by varying the content of Sr²⁺. The synthesized compounds were evaluated by XRD, SEM, XPS, setting time, compressive strength, SBF immersion, and colorimetric CCK-8 assay. The results showed that Sr²⁺ can improve the compressive strength and cell activity of calcium phosphate bone cement.

Is Zinc an Important Trace Element on Bone-Related Diseases and Complications? A Meta-analysis and Systematic Review from Serum Level, Dietary Intake, and Supplementation Aspects

Bone-related diseases are very common problems, especially in the elderly population. Zinc takes part in the growth and maintenance of healthy bones. This meta-analysis aims to evaluate the effects of zinc supplementation or dietary zinc intake on serum zinc levels and bone turnover markers. A systematical research was performed with 2899 articles in PubMed, WoS, and Scopus for relevant articles in English which have mean/standard deviation values of serum zinc levels, dietary zinc intake/zinc supplementation (mg/day), and bone turnover markers up to February 2020. In the overall analysis, serum zinc level was significantly lower in patients with osteoporosis compared with controls (p 0.0002). Dietary zinc intake decreased in the fracture group compared with controls according to subgroup analysis patients with fracture (p 0.02). Zinc supplementation was effective on the femoral neck (p < 0.0001) and lumbar spine (p 0.05) bone mineral density (BMD). In the correlation analysis of the data obtained from all of the included studies, serum osteocalcin (p 0.0106, r - 0.9148) correlated with serum zinc level. In conclusion, serum zinc level and dietary zinc intake could have an essential role in preventing osteoporosis. Zinc supplementation might improve bone turnover markers for bone formation such as serum osteocalcin and serum alkaline phosphatase and also, BMD at the site of the femoral neck.

Zn-doping of silicate and hydroxyapatite-based cements: Dentin mechanobiology and bioactivity

The objective was to state zinc contribution in the effectiveness of novel zinc-doped dentin cements to achieve dentin remineralization, throughout a literature or narrative exploratory review. Literature search was conducted using electronic databases, such as PubMed, MEDLINE, DIMDI, Embase, Scopus and Web of Science. Both zinc-doping silicate and hydroxyapatite-based cements provoked an increase of both bioactivity and intrafibrillar mineralization of dentin. Zinc-doped hydroxyapatite-based cements (oxipatite) also induced an increase in values of dentin nano-hardness, Young's modulus and dentin resistance to deformation. From Raman analyses, it was stated higher intensity of phosphate peaks and crystallinity as markers of dentin calcification, in the presence of zinc. Zinc-based salt formations produced low microleakage and permeability values with hermetically sealed tubules at radicular dentin. Dentin treated with oxipatite attained preferred crystal grain orientation with polycrystalline lattices. Thereby, oxipatite mechanically reinforced dentin structure, by remineralization. Dentin treated with oxipatite produced immature crystallites formations, accounting for high hydroxyapatite solubility, instability and enhanced remineralizing activity.

Bioinorganic supplementation of calcium phosphate-based bone substitutes to improve in vivo performance: a systematic review and meta-analysis of animal studies

Supplementation of CaP-based bone graft substitutes with bioinorganics such as strontium, zinc or silicon is an interesting approach to increase the biological performance in terms of bone regenerative potential of calcium phosphate (CaP)-based bone substitutes. However, the in vivo efficacy of this approach has not been systematically analyzed, yet. Consequently, we performed a systematic review using the available literature regarding the effect of bioinorganic supplementation in CaP-based biomaterials on new bone formation and material degradation in preclinical animal bone defect models and studied this effect quantitatively by performing a meta-analysis. Additional subgroup analyses were used to study the effect of different bioinorganics, animal model, or phase category of CaP-based biomaterial on bone formation or material degradation. Results show that bioinorganic supplementation increases new bone formation (standardized mean difference [SMD]: 1.43 SD, confidence interval [CI]: 1.13-1.73). Additional subgroup analysis showed that strontium, magnesium and silica significantly enhanced bone formation, while zinc did not have any effect. This effect of bioinorganic supplementation on new bone formation was stronger for DCPD or β-TCP and biphasic CaPs than for HA or α-TCP (p < 0.001). In general, material degradation was slightly hindered by bioinorganic supplementation (mean difference [MD]: 0.84%, CI: 0.01-1.66), with the exception of strontium that significantly enhanced degradation. Overall, bioinorganic supplementation represents an effective approach to enhance the biological performance of CaP-based bone substitutes.

Biomimetic trace metals improve bone regenerative properties of calcium phosphate bioceramics

The bone regenerative capacity of synthetic calcium phosphates (CaPs) can be enhanced through the enrichment with selected metal trace ions. However, defining the optimal elemental composition required for bone formation is challenging due to many possible concentrations and combinations of these elements. We hypothesized that the ideal elemental composition exists in the inorganic phase of the bone extracellular matrix (ECM). To study our hypothesis, we first obtained natural hydroxyapatite through the calcination of bovine bone, which was then investigated its reactivity with acidic phosphates to produce CaP cements. Bioceramic scaffolds fabricated using these cements were assessed for their composition, properties, and in vivo regenerative performance and compared with controls. We found that natural hydroxyapatite could react with phosphoric acid to produce CaP cements with biomimetic trace metals. These cements present significantly superior in vivo bone regenerative performance compared with cements prepared using synthetic apatite. In summary, this study opens new avenues for further advancements in the field of CaP bone biomaterials by introducing a simple approach to develop biomimetic CaPs. This work also sheds light on the role of the inorganic phase of bone and its composition in defining the regenerative properties of natural bone xenografts.

Zinc Supplementation Increased Bone Mineral Density, Improves Bone Histomorphology, and Prevents Bone Loss in Diabetic Rat

Diabetic osteoporosis (DOP) is a complication of diabetes, with the characteristics of bone mineral density (BMD) reduction and bone structure destruction. Zinc was reported has a benefit effect on postmenopausal osteoporosise, it was also has hypoglycemic effect, whether zinc was beneficial on diabetes-induced osteoporosis has not been reported. So in the present study, we established a diabetic rat model by streptozotocin injection (60 mg/kg), and administered zinc sulfate by oral gavage to investigate the protective effects of zinc on DOP and the underline possible mechanism. Thirty six Sprague Dawley rats were divided into T1DM group (diabetic rats), control group (vehicle treatment), and T1DM-Zinc group (diabetic rats administered zinc sulfate 0.25 mg/kg by oral gavage). The bone histomorphological parameters, serum bone metabolism markers (including ALP, OPG, RUNX 2, and RANKL), BMD, and bone marrow adipocyte numbers were detected after eight weeks of zinc sulfate treatment. The results showed zinc sulfate administration (0.25 mg/kg/d) decreased blood glucose, increased the BMD, decreased serum ALP, and RANKL, increased serum OPG and RUNX 2 levels, as well as OPG/RANKL ratio of T1DM rats. Meanwhile, the bone histomorphological parameters, bone marrow adipocytes numbers were returned to be normal. The RUNX 2, and OPG mRNA expression levels in bone tissues of T1DM-Zinc group rats were increased after zinc sulfate treatment compared with the diabetic rats (P < 0.05). Those indicating that zinc sulfate can prevent DOP, the protective mechanism were mainly related to its hypoglycemic effect, bone marrow lipogenesis inhibition effect, OPG/RANKL ratio and RUNX 2 up-regulation effect.

Zn-HA/Bi-HA biphasic coatings on Titanium: Fabrication, characterization, antibacterial and biological activity

Hydroxyapatite (HA) coatings have been of important as biocompatible coatings for dental and bone tissue engineering application. However, the poor antibacterial performance and weak biological activity of HA coatings limited their clinical applications. As a strategy to improve the antibacterial performance and biological activity of HA, Zinc and bismuth ions were incorporated into HA lattice by substituting Ca²⁺ ions, respectively, and thus zinc substituted hydroxyapatite/bismuth substituted hydroxyapatite (Zn-HA/Bi-HA) biphasic coatings on titanium plates with various ratios were fabricated via sol-gel and dip-coating processes. The purity of the Zn-HA and Bi-HA phase was confirmed by X-ray diffraction (XRD) test. The biphasic coatings showed slower dissolution rate than pure HA coating. Furthermore, the Zn-HA/Bi-HA coatings reveal good biomineralization activity in simulated body fluid (SBF) by forming regular spherical apatite agglomerates. Moreover, the biphasic Zn-HA/Bi-HA coatings exhibited that improved antimicrobial activity against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) as compared to pure HA coatings. The CCK-8 assays demonstrate Zn-HA/Bi-HA coatings showed no toxicity to MG63 cells, and the Zn-HA/Bi-HA2 (Zn-HA:Bi-HA=64:1) coating is more effective to enhance the proliferation of MG63 cells compared to other coatings. This finding suggests Zn-HA/Bi-HA biphasic coatings are promising candidates for biomedical applications.

Zinc doping induced differences in the surface composition, surface morphology and osteogenesis performance of the calcium phosphate cement hydration products

In order to investigate the influence of Zn on the hydration reaction of calcium phosphate cement (CPC), the incompletely hydrated CPC tablets were kept soaking in varying zinc-containing tris-(hydroxymethyl)-aminomethane/hydrochloric acid (Zn-Tris-HCl) buffers. It was found that Zn could retard the CPC hydration, the inhibitory effect was in direct proportional to the Zn content in the Zn-Tris-HCl buffer, and overhigh concentration of Zn (≧800 μM) caused the CPC hydration products having different phase composition and surface morphology. Cell culture experimental results revealed the CPC tablets which were soaked in the Zn-Tris-HCl buffer containing relative low Zn content (≦320 μM) favored the mouse bone mesenchymal stem cells (mBMSCs) spreading. When Zn-doped CPC tablets released 10.91 to 27.15 μM of zinc ions into the cell culture medium, it greatly contributed to the improvement of the proliferation ability and the alkaline phosphatase (ALP) activity of the mBMSCs. In the same case, the expression of osteogenesis related genes such as collagen I and runt-related transcription factor 2 was remarkably up-regulated as well. However, the release of high concentration of Zn (128.58 μM) would significantly reduce the ALP activity of the mBMSCs. Therefore, Zn not only facilitates osteogenesis but also affects the CPC hydration behavior, and the CPC with suitable Zn dosage concentration has great potentials to be used for clinical bone repairing.

Electrospun polycaprolactone membranes with Zn-doped bioglass for nasal tissues treatment

In this work, composite membranes were investigated as future components of a layered implant for the reconstruction of nasal septum. Incorporation of zinc ions into nasal implants could potentially provide antibacterial properties to decrease or eliminate bacterial infections and subsequent surgical complications. Two types of membranes were prepared using an electrospinning method: PCL with bioglass and PCL with bioglass doped with Zn. The aim of this work was to investigate the influence of bioglass addition on the morphology, fiber diameter and composition of the membranes. The apatite-forming ability was examined in Simulated Body Fluid (SBF). The cytotoxicity of the membranes, ALP activity and in vitro mineralization were evaluated in cell culture. The mineralization and ALP activity was higher for polycaprolactone membranes modified with Zn doped bioglass than compared to pure PCL membranes or control material. The results proved that the presence of Zn²⁺ in the electrospun membranes = influence the osteogenic differentiation of cells.

3D-printed bioceramic scaffolds: From bone tissue engineering to tumor therapy

Toward the aim of personalized treatment, three-dimensional (3D) printing technology has been widely used in bone tissue engineering owing to its advantage of a fast, precise, and controllable fabrication process. Conventional bioceramic scaffolds are mainly used for bone tissue engineering; however, there has been a significant change in the application of bioceramic scaffolds during the past several years. Therefore, this review focuses on 3D-printed bioceramic scaffolds with different compositions and hierarchical structures (macro, micro, and nano scales), and their effects on the mechanical, degradation, permeability, and biological properties. Further, this review highlights 3D-printed bioceramic scaffolds for applications extending from bone tissue regeneration to bone tumor therapy. This review emphasizes recent developments in functional 3D-printed bioceramic scaffolds with the ability to be used for both tumor therapy and bone tissue regeneration. Considering the challenges in bone tumor therapy, these functional bioceramic scaffolds have a great potential in repairing bone defects induced by surgery and kill the possibly residual tumor cells to achieve bone tumor therapy. Finally, a brief perspective regarding future directions in this field was also provided. The review not only gives a summary of the research developments in bioceramic science but also offers a new therapy strategy by extending multifunctions of traditional biomaterials toward a specific disease.

STATEMENT OF SIGNIFICANCE

This review outlines the development tendency of 3D-printed bioceramic scaffolds for applications ranging from bone tissue regeneration to bone tumor therapy. Conventional bioceramic scaffolds are mainly used for bone tissue engineering; however, there has been a significant change in the application of bioceramic scaffolds during the past several years. Therefore, this review focuses on 3D-printed bioceramic scaffolds with different compositions and hierarchical structures (macro, micro, and nano scales), and their effects on the mechanical, degradation, permeability, and biological properties. Further, this review highlights 3D-printed bioceramic scaffolds for applications extending from bone tissue regeneration to bone tumor therapy. This review emphasizes recent developments in the functional 3D-printed bioceramic scaffolds with the ability to be used for both bone tumor therapy and bone tissue regeneration.

3D printed β-TCP bone tissue engineering scaffolds: Effects of chemistry on in vivo biological properties in a rabbit tibia model

In this study the effects of 3D printed SiO2 and ZnO doped tricalcium phosphate (TCP) scaffolds with interconnected pores were evaluated on the in vivo bone formation and healing properties of a rabbit tibial defect model. Pure and doped TCP scaffolds were fabricated by a ceramic powder-based 3D printing technique and implanted into critical sized rabbit tibial defects for up to 4 months. In vivo bone regeneration was evaluated using chronological radiological examination, histological evaluations, SEM micrographs and fluorochrome labeling studies. Radiograph results showed that Si/Zn doped samples had slower degradation kinetics than the pure TCP samples. 3D printing of TCP scaffolds improved bone formation. The addition of dopants in the TCP scaffolds improved osteogenic capabilities when compared to the pure scaffolds. In summary, our findings indicate that addition of dopants to the TCP scaffolds enhanced bone formation and in turn leading to accelerated healing.

Calcium phosphate cements for bone engineering and their biological properties

Calcium phosphate cements (CPCs) are frequently used to repair bone defects. Since their discovery in the 1980s, extensive research has been conducted to improve their properties, and emerging evidence supports their increased application in bone tissue engineering. Much effort has been made to enhance the biological performance of CPCs, including their biocompatibility, osteoconductivity, osteoinductivity, biodegradability, bioactivity, and interactions with cells. This review article focuses on the major recent developments in CPCs, including 3D printing, injectability, stem cell delivery, growth factor and drug delivery, and pre-vascularization of CPC scaffolds via co-culture and tri-culture techniques to enhance angiogenesis and osteogenesis.

Promotive Effect of Zinc Ions on the Vitality, Migration, and Osteogenic Differentiation of Human Dental Pulp Cells

Zinc is an essential trace element for proper cellular function and bone formation. However, its exact role in the osteogenic differentiation of human dental pulp cells (hDPCs) has not been fully clarified before. Here, we speculated that zinc may be effective to regulate their growth and osteogenic differentiation properties. To test this hypothesis, different concentrations (1 × 10^-5, 4 × 10^-5, and 8 × 10^-5 M) of zinc ions (Zn²⁺) were added to the basic growth culture medium and osteogenic inductive medium. Cell viability and migration were measured by cell counting kit-8 (CCK-8) and transwell migration assay in the basic growth culture medium, respectively. The reverse transcription-quantitative polymerase chain reaction (RT-qPCR) was used to detect the gene expression levels of selective osteogenic differentiation markers and zinc transporters. Alkaline phosphatase (ALP) activity analysis and alizarin red S staining were used to investigate the mineralization of hDPCs. Exposure of hDPCs to Zn²⁺ stimulated their viability and migration capacity in a dose- and time-dependent manner. RT-qPCR assay revealed elevated expression levels of osteogenic differentiation-related genes and zinc transporters genes in various degrees. ALP activity was also increased with elevated Zn²⁺ concentrations and extended culture periods, but enhanced matrix nodules formation were observed only in 4 × 10^-5 and 8 × 10^-5 M Zn²⁺ groups. These findings suggest that specific concentrations of Zn²⁺ could potentiate the vitality, migration, and osteogenic differentiation of hDPCs. We may combine optimum zinc element into pulp capping materials to improve their biological performance.

IGF-loaded silicon and zinc doped brushite cement: physico-mechanical characterization and in vivo osteogenesis evaluation

Dopants play critical roles in controlling the physical, mechanical, degradation kinetics, and in vivo properties of calcium phosphates. The aim of the present study was to evaluate the effects of silicon (Si) and zinc (Zn) dopants on the physico-mechanical and in vivo osteogenesis properties of brushite cements (BrCs) alone and in combination with insulin like growth factor 1 (IGF-1). Addition of 0.5 wt% Si did not alter the setting time, β-TCP content, and compressive strength of BrCs significantly; however, 0.25 wt% Zn incorporation was accompanied by a significant decrease in mechanical strength from 4.78 ± 0.21 MPa for pure BrC to 3.78 ± 0.59 MPa and 3.28 ± 0.22 MPa for Zn-BrC and Si/Zn-BrC, respectively. The in vivo bone regeneration properties of doped BrCs alone and in combination with IGF-1 were assessed and compared using chronological radiography, histology, scanning electron microscopy and fluorochrome labeling at 2 and 4 months post implantation in a rabbit femoral defect model. Based on in vivo characterization focusing on osteogenesis and vasculogenesis, Si-BrC and Si/Zn-BrC showed the best performance followed by Zn-BrC and pure BrCs. Addition of IGF-1 further improved bone regeneration. Our findings confirm that addition of Si and/or Zn alters the physico-mechanical properties of BrCs and promotes the early stage in vivo osseointegration and bone remodeling properties.

Composites of gellan gum hydrogel enzymatically mineralized with calcium-zinc phosphate for bone regeneration with antibacterial activity

Gellan gum hydrogels functionalized with alkaline phosphatase were enzymatically mineralized with phosphates in mineralization medium containing calcium (Ca) and zinc (Zn) to improve their suitability as biomaterials for bone regeneration. The aims of the study were to endow mineralized hydrogels with antibacterial activity by incorporation of Zn in the inorganic phase, and to investigate the effect of Zn incorporation on the amount and type of mineral formed, the compressive modulus of the mineralized hydrogels and on their ability to support adhesion and growth of MC3T3-E1 osteoblast-like cells. Mineralization medium contained glycerophosphate (0.05 m) and three different molar Ca:Zn ratios, 0.05:0, 0.04:0.01 and 0.025:0.025 (all mol/dm³ ), hereafter referred to as A, B and C, respectively. FTIR, SAED and TEM analysis revealed that incubation for 14 days caused the formation of predominantly amorphous mineral phases in sample groups A, B and C. The presence of Zn in sample groups B and C was associated with a drop in the amount of mineral formed and a smaller mineral deposit morphology, as observed by SEM. ICP-OES revealed that Zn was preferentially incorporated into mineral compared to Ca. Mechanical testing revealed a decrease in compressive modulus in sample group C. Sample groups B and C, but not A, showed antibacterial activity against biofilm-forming, methicillin-resistant Staphylococcus aureus. All sample groups supported cell growth. Zn incorporation increased the viable cell number. The highest values were seen on sample group C. In conclusion, the sample group containing the most Zn, i.e. group C, appears to be the most promising. Copyright © 2015 John Wiley & Sons, Ltd.

Preparation and in vitro cell-biological performance of sodium alginate/nano-zinc silicate co-modified calcium silicate bioceramics

We have prepared a (Zn, Na)-containing layer on the surface of calcium silicate bioceramics, which are spin-coated with sodium alginate and nano-zinc silicate.

Effects of zinc-substituted nano-hydroxyapatite coatings on bone integration with implant surfaces

OBJECTIVE

The purpose of this study was to investigate the effects of a zinc-substituted nano-hydroxyapatite (Zn-HA) coating, applied by an electrochemical process, on implant osseointegraton in a rabbit model.

METHODS

A Zn-HA coating or an HA coating was deposited using an electrochemical process. Surface morphology was examined using field-emission scanning electron microscopy. The crystal structure and chemical composition of the coatings were examined using an X-ray diffractometer (XRD) and Fourier transform infrared spectroscopy (FTIR). A total of 78 implants were inserted into femurs and tibias of rabbits. After two, four, and eight weeks, femurs and tibias were retrieved and prepared for histomorphometric evaluation and removal torque (RTQ) tests.

RESULTS

Rod-like HA crystals appeared on both implant surfaces. The dimensions of the Zn-HA crystals seemed to be smaller than those of HA. XRD patterns showed that the peaks of both coatings matched well with standard HA patterns. FTIR spectra showed that both coatings consisted of HA crystals. The Zn-HA coating significantly improved the bone area within all threads after four and eight weeks (P<0.05), the bone to implant contact (BIC) at four weeks (P<0.05), and RTQ values after four and eight weeks (P<0.05).

CONCLUSIONS

The study showed that an electrochemically deposited Zn-HA coating has potential for improving bone integration with an implant surface.

Zinc in calcium phosphate mediates bone induction: in vitro and in vivo model

Zinc-containing tricalcium phosphate (Zn-TCP) was synthesized to investigate the role of zinc in osteoblastogenesis, osteoclastogenesis and in vivo bone induction in an ectopic implantation model. Zinc ions were readily released in the culture medium. Zn-TCP with the highest zinc content enhanced the alkaline phosphatase activity of human bone marrow stromal cells and tartrate-resistant acid phosphatase activity, as well as multinuclear giant cell formation of RAW264.7 monocyte/macrophages. RAW264.7 cultured with different dosages of zinc supplements in medium with or without zinc-free TCP showed that zinc could influence both the activity and the formation of multinuclear giant cells. After a 12-week implantation in the paraspinal muscle of canines, de novo bone formation and bone incidence increased with increasing zinc content in Zn-TCP - up to 52% bone in the free space. However, TCP without zinc induced no bone formation. Although the observed bone induction cannot be attributed to zinc release alone, these results indicate that zinc incorporated in TCP can modulate bone metabolism and render TCP osteoinductive, indicating to a novel way to enhance the functionality of this synthetic bone graft material.

Understanding of dopant-induced osteogenesis and angiogenesis in calcium phosphate ceramics

General trends in synthetic bone grafting materials are shifting towards approaches that can illicit osteoinductive properties. Pharmacologics and biologics have been used in combination with calcium phosphate (CaP) ceramics, however, they have recently become the target of scrutiny over safety. The importance of trace elements in natural bone health is well documented. Ions, for example, lithium, zinc, magnesium, manganese, silicon, strontium, etc., have been shown to increase osteogenesis and neovascularization. Incorporation of dopants (trace metal ions) into CaPs can provide a platform for safe and efficient delivery in clinical applications where increased bone healing is favorable. This review highlights the use of trace elements in CaP biomaterials, and offers an insight into the mechanisms of how metal ions can enhance both osteogenesis and angiogenesis.

Long-term biocompatibility evaluation of 0.5 % zinc containing hydroxyapatite in rabbits

This study investigates the long-term biocompatibility of 0.5 % zinc-containing hydroxyapatite compared with hydroxyapatite. Spheres (425 < ∅ < 550) of both materials were produced by extrusion of ceramic slurry in calcium chloride and characterized by FTIR, XRD, XRF and SEM. Fifteen White New Zealand rabbits were submitted to general anesthesia, and an perforation (2 mm), was made in each tibia, one for zinc-containing hydroxyapatite sphere implantation and one for hydroxyapatite sphere implantation. After 26, 52 and 78 weeks, the animals were euthanized, and the fragment containing the biomaterial was harvested. A 30-50 μm section was obtained for histological analysis in bright field and polarized light. SEM images revealed similar morphologies between the tested biomaterials. Histological analysis showed that there was no difference between the test groups. The morphometric analysis, however, indicates that there was a greater absorption. The materials are biocompatible, promote osteogenesis and that the zinc-containing hydroxyapatite microspheres were absorbed more quickly.

Calcium phosphate cements as drug delivery materials

Calcium phosphate cements are used as synthetic bone grafts, with several advantages, such as their osteoconductivity and injectability. Moreover, their low-temperature setting reaction and intrinsic porosity allow for the incorporation of drugs and active principles in the material. It is the aim of the present work to: a) provide an overview of the different approaches taken in the application of calcium phosphate cements for drug delivery in the skeletal system, and b) identify the most significant achievements. The drugs or active principles associated to calcium phosphate cements are classified in three groups, i) low molecular weight drugs; ii) high molecular weight biomolecules; and iii) ions.

Effects of silica and zinc oxide doping on mechanical and biological properties of 3D printed tricalcium phosphate tissue engineering scaffolds

OBJECTIVES

To evaluate the effects of silica (SiO(2)) (0.5 wt%) and zinc oxide (ZnO) (0.25 wt%) dopants on the mechanical and biological properties of tricalcium phosphate (TCP) scaffolds with three dimensionally (3D) interconnected pores.

METHODS

Scaffolds were created with a commercial 3D printer. Post sintering phase analysis was determined by X-ray diffraction. Surface morphology of the scaffolds was examined by field emission scanning electron microscopy (FESEM). Mechanical strength was evaluated with a screw driven universal testing machine. MTT assay was used for cellular proliferation characteristics and cellular morphology was examined by FESEM.

RESULTS

Addition of dopants into TCP increased the average density of pure TCP from 90.8 ± 0.8% to 94.1 ± 1.6% and retarded the β to α phase transformation at high sintering temperatures, which resulted in up to 2.5 fold increase in compressive strength. In vitro cell-materials interaction studies, carried out using hFOB cells, confirmed that the addition of SiO(2) and ZnO to the scaffolds facilitated faster cell proliferation when compared to pure TCP scaffolds.

SIGNIFICANCE

Addition of SiO(2) and ZnO dopants to the TCP scaffolds showed increased mechanical strength as well as increased cellular proliferation.

Synthesis and characterization of hierarchically macroporous and mesoporous CaO-MO-SiO(2)-P(2)O(5) (M=Mg, Zn, Sr) bioactive glass scaffolds

Mg-, Zn- and Sr-doped hierarchically macroporous and mesoporous CaO-MO-SiO(2)-P(2)O(5) (M=Mg, Zn or Sr) bioactive glass (HMMBG) scaffolds were synthesized using the non-ionic block copolymer EO(20)PO(70)EO(20) and polyurethane sponges as cotemplates. The Mg-, Zn- or Sr-doped HMMBG scaffolds showed no distinct difference in phase composition, macroporous structure or pore volume from the HMMBG scaffolds without Mg, Zn or Sr. The Mg-, Zn- and Sr-doped HMMBG scaffolds showed no cytotoxicity. The gradual release of Ca, P, Si, Mg, Zn and Sr into the culture medium from these scaffolds contributed to the enhancement of the proliferation and ALP activity of mesenchymal stem cells (MSCs). The Mg-, Zn- and Sr-doped HMMBG scaffolds may be used as bone substitute materials.

Ionic substitutions in calcium phosphates synthesized at low temperature

Ionic substitutions have been proposed as a tool to improve the biological performance of calcium phosphate based materials. This review provides an overview of the recent results achieved on ion-substituted calcium phosphates prepared at low temperature, i.e. by direct synthesis in aqueous medium or through hydrolysis of more soluble calcium phosphates. Particular attention is focused on several ions, including Si, Sr, Mg, Zn and Mn, which are attracting increasing interest for their possible biological role, and on the recent trends and developments in the applications of ion-substituted calcium phosphates in the biomedical field.

Zinc-containing apatite layers on external fixation rods promoting cell activity

Zinc-containing apatite layers were successfully formed on commercially available anodically oxidized Ti external fixation rods using ZnCl(2)-containing supersaturated calcium phosphate solutions. With an increase in concentration of ZnCl(2) in the supersaturated calcium phosphate solutions, the amounts of zinc that precipitated on the Ti external fixation rods increased (from 0 to 0.195 + or - 0.020 microg cm(-2)); meanwhile, the amounts of calcium and phosphorus that precipitated on the Ti external fixation rods decreased (from 11.2 + or - 1.5 and 4.8 + or - 0.5 microg cm(-2) to 2.9 + or - 1.6 and 1.3 + or - 0.9 microg cm(-2), respectively). The zinc-containing apatite layers precipitated on the Ti external fixation rods caused a significant increase in fibroblastic proliferation, osteoblastic proliferation and differentiation in vitro. The Ti external fixation rods coated with zinc-containing apatite layers are expected to be more effective in accelerating the tissue regeneration around the surgical site than those coated with an apatite layer.

Brushite-Forming Mg-, Zn- and Sr-Substituted Bone Cements for Clinical Applications

Calcium phosphate cements have been in clinical use for the last 10 years. Their most salient features include good biocompatibility, excellent bioactivity, self-setting characteristics, low setting temperature, adequate stiffness, and easy shaping to accomodate any complicated geometry. They are commonly used in filling bone defects and trauma surgeries as mouldable paste-like bone substitute materials. Substitution of trace elements, such as Mg, Sr and Zn ions, into the structure of calcium phosphates is the subject of widespread investigation nowadays, because of their impending role in the biological process. Subtle differences in composition and structure of these materials may have a profound effect on their in vivo behaviour. Therefore, the main goal of this paper is to provide a simple, but comprehensive overview of the present achievements relating to brushite-forming cements doped with Mg, Zn and Sr, and to identify new developments and trends. In particular, the influence of ionic substitution on the chemical, physical and biological properties of these materials is discussed.