Magnesium substitution in the structure of orthopedic nanoparticles: A comparison between amorphous magnesium phosphates, calcium magnesium phosphates, and hydroxyapatites

Improved protective properties of Mg alloy AZ31 using bis-[triethoxysilylpropyl] tetrasulfide silane films modified with nano TiO2 by electrochemically assisted deposition

Magnesium (Mg) and its alloys were favored by biomedical practitioners thanks to availability of bioactivity and degradability. However, the mismatch between the degradation properties of Mg alloys and the rate of osteogenesis often led to implant failure and bacterial infections within the desired period. The goal of this study was to improve the corrosion resistance of Mg alloys, providing theoretical guidance for solving the problems of implantable Mg-based materials. In this experiment, we prepared a dense and uniform BTESPT/TiO2 film layer on the surface of Mg substrate by electrochemically assisted deposition. The BTESPT/TiO2 film layer provided a physical barrier to avoid direct contact between AZ31 and the corrosive medium. When the addition amount was 2 g/L TiO2, the coating had the best corrosion resistance behavior, its corrosion current density could be up to 9.973×10-8 A/cm2. The BTESPT/TiO2 revealed good cell viability as well as osteogenic differentiation potential on MC3T3-E1 cells.

An injectable porous bioactive magnesium phosphate bone-cement foamed with calcium carbonate and citric acid for periodontal bone regeneration

Magnesium phosphate cement (MPC) has been evaluated as a novel bone substitute owing to its favorable biocompatibility, plasticity, and osteogenic potential. However, the low porosity of MPC prevents growth factors and osteoblasts from fully growing into the material, thereby limiting its clinical use. In this study, different concentrations (0-5%) of calcium carbonate and citric acid (CA) were used as foaming agents to prepare porous MPC. The MPC containing 3% CaCO₃/CA exhibited the best physicochemical properties, including greater porosity, improved injectability, extended setting time, and decreased hydration temperature. The proliferation and adhesion of cells on 3%CaCO₃/CA-MPC were higher than those on MPC alone. To explore its osteogenesis in vivo, 3% CaCO₃/CA-MPC and Bio-Oss® bone powder were implanted into periodontal bone defects in rats for 4 weeks and 12 weeks, respectively. Micro-CT and histological analysis demonstrated the improved bone regeneration of 3%CaCO₃/CA-MPC compared to the blank group (P < 0.05); it had slightly lower bone regeneration than the Bio-Oss® group but no statistical difference. The results indicated that porous MPC foamed with calcium carbonate and CA improved its physicochemical properties and enhanced its biocompatibility, making it a promising material for bone regeneration.

3D-printed MgO nanoparticle loaded polycaprolactone β-tricalcium phosphate composite scaffold for bone tissue engineering applications: In-vitro and in-vivo evaluation

Magnesium (Mg) plays an important role in controlling bone apatite structure and density and is a potential bioactive material in repairing critical-sized bone defects. In this study, we aimed to evaluate the effect of adding NanoMgO to polycaprolactone/beta-tricalcium phosphate (PCL/β-TCP) scaffolds on bone regeneration. Novel 3D-printed porous PCL/β-TCP composite scaffolds containing 10% nanoMgO were fabricated by fused deposition modeling (FDM) and compared with PCL/β-TCP (1:1) scaffolds (control). The morphology and physicochemical properties of the scaffolds were characterized by ATR-FTIR, XRD, scanning electron microscope-energy dispersive X-ray analysis (SEM-EDX), transmission-electron-microscopy (TEM), water contact angle, and compressive strength tests and correlated to its cytocompatibility and osteogenic capacity in-vitro. To evaluate in-vivo osteogenic capacity, bone-marrow-derived stem cell (BMSC)-loaded scaffolds were implanted into 8 mm rat critical-sized calvarial defects for 12 weeks. The hydrophilic scaffolds showed 50% porosity (pore size = 504 μm). MgO nanoparticles (91.5 ± 27.6 nm) were homogenously dispersed and did not adversely affect BMSCs' viability and differentiation. Magnesium significantly increased elastic modulus, pH, and degradation. New bone formation (NBF) in Micro-CT was 30.16 ± 0.31% and 23.56 ± 1.76% in PCL/β-TCP/nanoMgO scaffolds with and without BMSCs respectively, and 19.38 ± 2.15% and 15.75 ± 2.24% in PCL/β-TCP scaffolds with and without BMSCs respectively. Angiogenesis was least remarkable in PCL/β-TCP compared with other groups (p < .05). Our results suggest that the PCL/β-TCP/nanoMgO scaffold is a more suitable bone substitute compared to PCL/β-TCP in critical-sized calvarial defects.

PEEK for Oral Applications: Recent Advances in Mechanical and Adhesive Properties

Polyetheretherketone (PEEK) is a thermoplastic material widely used in engineering applications due to its good biomechanical properties and high temperature stability. Compared to traditional metal and ceramic dental materials, PEEK dental implants exhibit less stress shielding, thus better matching the mechanical properties of bone. As a promising medical material, PEEK can be used as implant abutments, removable and fixed prostheses, and maxillofacial prostheses. It can be blended with materials such as fibers and ceramics to improve its mechanical strength for better clinical dental applications. Compared to conventional pressed and CAD/CAM milling fabrication, 3D-printed PEEK exhibits excellent flexural and tensile strength and parameters such as printing temperature and speed can affect its mechanical properties. However, the bioinert nature of PEEK can make adhesive bonding difficult. The bond strength can be improved by roughening or introducing functional groups on the PEEK surface by sandblasting, acid etching, plasma treatment, laser treatment, and adhesive systems. This paper provides a comprehensive overview of the research progress on the mechanical properties of PEEK for dental applications in the context of specific applications, composites, and their preparation processes. In addition, the research on the adhesive properties of PEEK over the past few years is highlighted. Thus, this review aims to build a conceptual and practical toolkit for the study of the mechanical and adhesive properties of PEEK materials. More importantly, it provides a rationale and a general new basis for the application of PEEK in the dental field.

Physicochemical degradation of calcium magnesium phosphate (stanfieldite) based bone replacement materials and the effect on their cytocompatibility

Regenerative bone implants should be completely replaced by new bone within a period of time corresponding to the growth rate of native bone. To meet this requirement, suitable biomaterials must be biodegradable and promote osteogenesis. The combination of slowly degrading but osteoconductive calcium phosphates (CPs) with rapidly degrading and mechanically more resilient magnesium phosphates represents a promising material class for this purpose. In order to create the best possible conditions for optimal implant integration, microporous calcium magnesium phosphate (CMP) cements were processed using 3D powder printing. This technique enables the production of a defect-adapted implant with an optimal fit and a high degree of open porosity to promote bone ingrowth. Four different compositions of 3D printed CMP ceramics were investigated with regard to essential properties of bone implants, including chemical composition, porosity, microstructure, mechanical strength, and cytocompatibility. The ceramics consisted of farringtonite (Mg₃(PO₄)₂) and stanfieldite (Ca₄Mg₅(PO₄)₆), with either struvite (NH₄MgPO₄·6H₂O) or newberyite (MgHPO₄·3H₂O) and brushite (CaHPO₄·2H₂O) as additional phases. The CMP materials showed open porosities between 13 and 28% and compressive strengths between 11 and 17 MPa, which was significantly higher, as compared with clinically established CP. The cytocompatibility was evaluated with the human fetal osteoblast cell line hFOB 1.19 and was proven to be equal or to even exceed that of tricalcium phosphate. Furthermore, a release of 4-8 mg magnesium and phosphate ions per mg scaffold material could be determined for CMPs over a period of 21 d. In the case of struvite containing CMPs the chemical dissolution of the cement matrix was combined with a physical degradation, which resulted in a mass loss of up to 3.1 wt%. In addition to its beneficial physical and biological properties, the proven continuous chemical degradation and bioactivity in the form of CP precipitation indicate an enhanced bone regeneration potential of CMPs.

Magnesium for Implants: A Review on the Effect of Alloying Elements on Biocompatibility and Properties

An attempt is made to cover the whole of the topic of biodegradable magnesium (Mg) alloys with a focus on the biocompatibility of the individual alloying elements, as well as shed light on the degradation characteristics, microstructure, and mechanical properties of most binary alloys. Some of the various work processes carried out by researchers to achieve the alloys and their surface modifications have been highlighted. Additionally, a brief look into the literature on magnesium composites as also been included towards the end, to provide a more complete picture of the topic. In most cases, the chronological order of events has not been particularly followed, and instead, this work is concentrated on compiling and presenting an update of the work carried out on the topic of biodegradable magnesium alloys from the recent literature available to us.

Magnesium Phosphate Bioceramics for Bone Tissue Engineering

Magnesium phosphate (MgP) is a family of newly developed resorbable bioceramics for bone tissue engineering. Although calcium phosphates (CaP) are the most commonly used bioceramics, low solubility, and slow degradation, when implanted in vivo, are their main drawbacks. Magnesium (Mg) is an essential element in the human body as it plays important role in bone metabolism, DNA stabilization, and skeletal development. Recent research on magnesium phosphates has established their higher degradability, in vitro, and in vivo biocompatibility. Compared to CaP, very limited research work has been found in the area of MgP. The prime goal of this review is to bring out the importance of magnesium phosphate ceramics for biomedical applications. In this review, we have discussed the synthesis methods, mechanical properties, in vitro and in vivo biocompatibility of MgP bioceramics. Moreover, we have highlighted the recent developments in metal ion-doped MgPs and MgP scaffolds for bone tissue engineering.

Antibacterial amorphous magnesium phosphate/graphene oxide for accelerating bone regeneration

Magnesium phosphates (MgP)s have attracted interest as an alternative biomaterial compared to the calcium phosphate (CaP)s compounds in the bone regeneration application in terms of their prominent biodegradability, lack of cytotoxicity, and ability of bone repair stimulation. Among them, amorphous magnesium phosphates (AMP)s indicated a higher rate of resorption, while preserving high osteoblasts viability and proliferation, which is comparable to their CaP peers. However, fast degradation of AMP leads to the initial fast release of Mg²⁺ ions and adverse effects on its excellent biological features. It seems that the addition of graphene oxide (GO) to magnesium phosphate can moderate its degradation rate. Hence, a novel in situ synthesized AMP powders containing 0.05, 0.25, 0.5, and 1 wt% of graphene oxide (AMP/GO) were developed to achieve a favorable degradation rate, desirable antibacterial properties against both Escherichia coli (E. coli), Staphylococcus aureus (S. aureus) accompanying with proper cell viability and proliferation. The incorporation of 0.5 wt% of graphene oxide into the AMP ceramic led to reduce the release of Mg²⁺ ions from 571.2 ± 12.9 mg/L to 372.8 ± 14.7 mg/L and P ions from 354.8 ± 11.9 mg/L to 245.3 ± 9.9 mg/L, at day 10 of immersion in PBS. Besides, AMP/0.5 GO bioceramics were capable of eradicating all bacterial colonies of both strains. On the other hand, MG63 cells viability went up from 143.46% ± 7.54 to 184.46% ± 11.54 on the 7th day of culture in the presence of 0.5 wt% of GO compared to pure AMP ceramic. Furthermore, alizarin red staining and alkaline phosphatase (ALP) activity demonstrated the ability of AMP/GO to maintain the osteogenic phenotype of MG63 cells during 7 days culture. Therefore, it can be concluded that well distributed and in situ synthesized AMP/0.5GO powders can be a promising biomaterial for bone tissue regeneration.

Latest Trends in Surface Modification for Dental Implantology: Innovative Developments and Analytical Applications

An increase in the world population and its life expectancy, as well as the ongoing concern about our physical appearance, have elevated the relevance of dental implantology in recent decades. Engineering strategies to improve the survival rate of dental implants have been widely investigated, focusing on implant material composition, geometry (usually guided to reduce stiffness), and interface surrounding tissues. Although efforts to develop different implant surface modifications are being applied in commercial dental prostheses today, the inclusion of surface coatings has gained special interest, as they can be tailored to efficiently enhance osseointegration, as well as to reduce bacterial-related infection, minimizing peri-implantitis appearance and its associated risks. The use of biomaterials to replace teeth has highlighted the need for the development of reliable analytical methods to assess the therapeutic benefits of implants. This literature review considers the state-of-the-art strategies for surface modification or coating and analytical methodologies for increasing the survival rate for teeth restoration.

Biodegradable magnesium phosphates in biomedical applications

As an essential element, magnesium is involved in a variety of physiological processes. Magnesium is the second most abundant cation in cells and the fourth most abundant cation in living...

Biocompatible magnesium-doped biphasic calcium phosphate for bone regeneration

Autologous bone grafting remains the gold standard for almost all bone void-filling orthopedic surgery. However, autologous bone grafting has several limitations, thus scientists are trying to identify an ideal synthetic material as an alternative bone graft substitute. Magnesium-doped biphasic calcium phosphate (Mg-BCP) has recently been in the spotlight and is considered to be a potential bone substitute. The Mg-BCP is a mixture of two bioceramics, that is, hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP), doped with Mg2+ , and can be synthesized through chemical wet-precipitation, sol-gel, single diffusion gel, and solid state reactions. Regardless of the synthesis routes, it is found that the Mg2+ preferentially accommodates in β-TCP lattice instead of the HA lattice. The addition of Mg2+ to BCP leads to desirable physicochemical properties and is found to enhance the apatite-forming ability as compared to pristine BCP. In vitro results suggest that the Mg-BCP is bioactive and not toxic to cells. Implantation of Mg-BCP in in vivo models further affirmed its biocompatibility and efficacy as a bone substitute. However, like the other bioceramics, the optimum physicochemical properties of the Mg-BCP scaffold have yet to be determined. Further investigations are required regarding Mg-BCP applications in bone tissue engineering.

Modification of polyetheretherketone implants: From enhancing bone integration to enabling multi-modal therapeutics

Polyetheretherketone (PEEK) is a popular thermoplastic material widely used in engineering applications due to its favorable mechanical properties and stability at high temperatures. With the first implantable grade PEEK being commercialized in 1990s, the use of PEEK has since grown exponentially in the biomedical field and has rapidly transformed a large section of the medical devices landscape. Nowadays, PEEK is a standard biomaterial used across a wide range of implant applications, however, its bioinertness remains a limitation for bone repair applications. The increasing demand for enhanced treatment efficacy/improved patient quality of life, calls for next-generation implants that can offer fast bone integration as well as other desirable therapeutic functions. As such, modification of PEEK implants has progressively shifted from offering desirable mechanical properties, enhancing bioactivity/fast osteointegration, to more recently, tackling post-surgery bacterial infection/biofilm formation, modulation of inflammation and management of bone cancers. Such progress is also accompanied by the evolution of the PEEK manufacturing technologies, to meet the ever increasing demand for more patient specific devices. However, no review has comprehensively covered the recently engaged application areas to date. This paper provides an up-to-date review on the development of PEEK-based biomedical devices in the past 10 years, with particularly focus on modifying PEEK for multi-modal therapeutics. The aim is to provide the peers with a timely update, which may guide and inspire the research and development of next generation PEEK-based healthcare products. STATEMENT OF SIGNIFICANCE: Significant progress has been made in PEEK processing and modification techniques in the past decades, which greatly contributed to its wide applications in the biomedical field. Despite the high volume of published literature on PEEK implant related research, there is a lack of review on its emerging applications in multi-modal therapeutics, which involve bone regeneration, anti-bacteria/anti-inflammation, and cancer inhibition, etc. This timely review covers the state-of-the-art in these exciting areas and provides the important guidance for next generation PEEK based biomedical device research and development.

Fused Filament Fabrication (Three-Dimensional Printing) of Amorphous Magnesium Phosphate/Polylactic Acid Macroporous Biocomposite Scaffolds

The ultimate goal of this paper is to develop novel ceramic-polymer-based biocomposite orthopedic scaffolds with the help of additive manufacturing. Specifically, we incorporate a bioceramic known as amorphous magnesium phosphate (AMP) into polylactic acid (PLA) with the help of the melt-blending technique. Magnesium phosphate (MgP) was chosen as the bioactive component as previous studies have confirmed its favorable biomaterial properties, especially in orthopedics. Special care was taken to develop constant diameter AMP-PLA composite filaments, which would serve as feedstock for a fused filament fabrication (FFF)-based three-dimensional (3D) printer. Before the filaments were used for FFF, a thorough set of characterization protocols comprising of phase analysis, microstructure evaluations, thermal analysis, rheological analysis, and in vitro degradation determinations was performed on the biocomposites. Scanning electron microscopy (SEM) results confirmed a homogenous dispersion of AMP particles in the PLA matrix. Rheological studies demonstrated good printability behavior of the AMP-PLA filaments. In vitro degradation studies indicated a faster degradation rate in the case of AMP-PLA filaments as compared to the single phase PLA filaments. Subsequently, the filaments were fed into an FFF setup, and tensile bars and design-specific macroporous AMP-PLA scaffolds were printed. The biocomposite exhibited favorable mechanical properties. Furthermore, in vitro cytocompatibility results revealed higher pre-osteoblast cell attachment and proliferation on AMP-PLA scaffolds as compared to single-phase PLA scaffolds. Altogether, this study provides a proof of concept that design-specific bioactive AMP-PLA biocomposite scaffolds fabricated by FFF can be potential candidates as medical implants in orthopedics.

Magnesium-alloy rods reinforced bioglass bone cement composite scaffolds with cortical bone-matching mechanical properties and excellent osteoconductivity for load-bearing bone in vivo regeneration

Various therapeutic platforms have been developed for repairing bone defects. However, scaffolds possess both cortical bone-matching mechanical properties and excellent osteoconductivity for load-bearing bone defects repair is still challenging in the clinic. In this study, inspired by the structure of the ferroconcrete, a high-strength bifunctional scaffold has been developed by combining surface-modified magnesium alloy as the internal load-bearing skeleton and bioglass-magnesium phosphate bone cement as the osteoconductive matrix. The scaffold combines the high mechanical strength and controllable biodegradability of surface-modified magnesium alloy with the excellent biocompatibility and osteoconductivity of bioglass-magnesium phosphate bone cement, thus providing support for load-bearing bone defects and subsequently bone regeneration. The scaffolds generate hydroxyapatite (HA) during the degrading in simulated body fluid (SBF), with the strength of the scaffold decreasing from 180 to 100 MPa in 6 weeks, which is still sufficient for load-bearing bone. Moreover, the scaffolds showed excellent osteoconductivity in vitro and in vivo. In a New Zealand White Rabbit radius defect model, the scaffolds degrade gradually and are replaced by highly matured new bone tissues, as assessed by image-based analyses (X-ray and Micro-CT) and histological analyses. The bone formation-related proteins such as BMP2, COL1a1 and OCN, all showed increased expression.

Surface Modified Techniques and Emerging Functional Coating of Dental Implants

Dental implants are widely used in the field of oral restoration, but there are still problems leading to implant failures in clinical application, such as failed osseointegration, marginal bone resorption, and peri-implantitis, which restrict the success rate of dental implants and patient satisfaction. Poor osseointegration and bacterial infection are the most essential reasons resulting in implant failure. To improve the clinical outcomes of implants, many scholars devoted to modifying the surface of implants, especially to preparing different physical and chemical modifications to improve the osseointegration between alveolar bone and implant surface. Besides, the bioactive-coatings to promote the adhesion and colonization of ossteointegration-related proteins and cells also aim to improve the osseointegration. Meanwhile, improving the anti-bacterial performance of the implant surface can obstruct the adhesion and activity of bacteria, avoiding the occurrence of inflammation related to implants. Therefore, this review comprehensively investigates and summarizes the modifying or coating methods of implant surfaces, and analyzes the ossteointegration ability and anti-bacterial characteristics of emerging functional coatings in published references.

Highly tunable bioactive fiber-reinforced hydrogel for guided bone regeneration

One of the most damaging pathologies that affects the health of both soft and hard tissues around the tooth is periodontitis. Clinically, periodontal tissue destruction has been managed by an integrated approach involving elimination of injured tissues followed by regenerative strategies with bone substitutes and/or barrier membranes. Regrettably, a barrier membrane with predictable mechanical integrity and multifunctional therapeutic features has yet to be established. Herein, we report a fiber-reinforced hydrogel with unprecedented tunability in terms of mechanical competence and therapeutic features by integration of highly porous poly(ε-caprolactone) fibrous mesh(es) with well-controlled 3D architecture into bioactive amorphous magnesium phosphate-laden gelatin methacryloyl hydrogels. The presence of amorphous magnesium phosphate and PCL mesh in the hydrogel can control the mechanical properties and improve the osteogenic ability, opening a tremendous opportunity in guided bone regeneration (GBR). Results demonstrate that the presence of PCL meshes fabricated via melt electrowriting can delay hydrogel degradation preventing soft tissue invasion and providing the mechanical barrier to allow time for slower migrating progenitor cells to participate in bone regeneration due to their ability to differentiate into bone-forming cells. Altogether, our approach offers a platform technology for the development of the next-generation of GBR membranes with tunable mechanical and therapeutic properties to amplify bone regeneration in compromised sites. STATEMENT OF SIGNIFICANCE: In this study, we developed a fiber-reinforced hydrogel platform with unprecedented tunability in terms of mechanical competence and therapeutic features for guided bone regeneration. We successfully integrated highly porous poly(ε-caprolactone) [PCL] mesh(es) into amorphous magnesium phosphate-laden hydrogels. The stiffness of the engineered hydrogel was significantly enhanced, and this reinforcing effect could be modulated by altering the number of PCL meshes and tailoring the AMP concentration. Furthermore, the fiber-reinforced hydrogel showed favorable cellular responses, significantly higher rates of mineralization, upregulation of osteogenic-related genes and bone formation. In sum, these fiber-reinforced membranes in combination with therapeutic agent(s) embedded in the hydrogel offer a robust, highly tunable platform to amplify bone regeneration not only in periodontal defects, but also in other craniomaxillofacial sites.

Microwave processing of calcium phosphate and magnesium phosphate based orthopedic bioceramics: A state-of-the-art review

The main theme of this paper is to review microwave-assisted synthesis and processing of calcium and magnesium phosphate bioceramics. Microwave processing of advanced materials has been an active field of research for the last three decades and has been already reviewed in the literature. Microwave processing of bioceramics is being pursued for almost the same period of time. Unfortunately, to the best of our knowledge, we are not aware of any comprehensive review in the literature. Our group has been a significant contributor to the field, and we feel that it is an appropriate time for reviewing the state-of-the-art of the field. The paper is divided into several sections. After rationalizing the motivation behind writing this paper in the introduction, the second section builds on some fundamental aspects of microwave-matter interactions. The third section, representing the synthesis aspects, is subdivided into five sub-sections focusing on various calcium and magnesium phosphates in both crystalline and amorphous forms. The fourth section focuses on magnesium phosphate-based bioceramics. The fifth and the sixth section describe results on the utility of microwave assistance in developing multi-functional coatings on medical implants and orthopedic cements respectively. The subsequent section reviews results on microwave sintering of calcium and magnesium phosphates. The paper concludes with remarks on unresolved issues and future directions of research. It is expected that this comprehensive review on the interdisciplinary topic will further propel the exploration of other novel applications of microwave technology in processing biomaterials by a diverse group of scientists and engineers. STATEMENT OF SIGNIFICANCE: 1. This review highlights the broad-spectrum capabilities of microwave applications in processing orthopedic bioceramics. 2. The article covers "processing" in the broadest sense of the word, comprising of material synthesis, sintering, coating formation, and setting of orthopedic cements. It also expands beyond conventional calcium phosphates to include the emergent family of magnesium phosphates. 3. In vitro/in vivo responses of microwave-processed bioceramics are discussed thus providing an integral understanding of biological aspects of these materials. 4. The comprehensive review on this interdisciplinary topic will help researchers in various disciplines to appreciate the significance and usefulness of microwaves in biomaterials processing. Further, we also believe that it will propel the exploration of other novel applications of microwave technology in the biomaterials sector.

Bioactive amorphous magnesium phosphate-polyetheretherketone composite filaments for 3D printing

OBJECTIVE

The aim of this study was to develop bioactive and osseointegrable polyetheretherketone (PEEK)-based composite filaments melt-blended with novel amorphous magnesium phosphate (AMP) particles for 3D printing of dental and orthopedic implants.

MATERIALS AND METHODS

A series of materials and biological analyses of AMP-PEEK were performed. Thermal stability, thermogravimetric and differential scanning calorimetry curves of as-synthesized AMP were measured. Complex viscosity, elastic modulus and viscous modulus were determined using a rotational rheometer. In vitro bioactivity was analyzed using SBF immersion method. SEM, EDS and XRD were used to study the apatite-forming ability of the AMP-PEEK filaments. Mouse pre-osteoblasts (MC3T3-E1) were cultured and analyzed for cell viability, proliferation and gene expression. For in vivo analyses, bare PEEK was used as the control and 15AMP-PEEK was chosen based on its in vitro cell-related results. After 4 or 12 weeks, animals were euthanized, and the femurs were collected for micro-computed tomography (μ-CT) and histology.

RESULTS

The collected findings confirmed the homogeneous dispersion of AMP particles within the PEEK matrix with no phase degradation. Rheological studies demonstrated that AMP-PEEK composites are good candidates for 3D printing by exhibiting high zero-shear and low infinite-shear viscosities. In vitro results revealed enhanced bioactivity and superior pre-osteoblast cell function in the case of AMP-PEEK composites as compared to bare PEEK. In vivo analyses further corroborated the enhanced osseointegration capacity for AMP-PEEK implants.

SIGNIFICANCE

Collectively, the present investigation demonstrated that AMP-PEEK composite filaments can serve as feedstock for 3D printing of orthopedic and dental implants due to enhanced bioactivity and osseointegration capacity.

Rationalization of the X-ray photoelectron spectroscopy of aluminium phosphates synthesized from different precursors

The aim of this paper is to clarify the assignments of X-ray photoelectron spectra of aluminium phosphate materials prepared from the reaction of phosphoric acid with three different aluminium precursors [Al(OH)₃, Al(NO₃)₃ and AlCl₃] at different annealing temperatures. The materials prepared have been studied by X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (XRD), infrared spectroscopy and high-resolution solid-state ³¹P NMR spectroscopy. A progressive polymerization from orthophosphate to metaphosphates is observed by XRD, ATR-FTIR and solid state ³¹P NMR, and on this basis the oxygen states observed in the XP spectra at 532.3 eV and 533.7 eV are assigned to P–O–Al and P–O–P environments, respectively. The presence of cyclic polyphosphates at the surface of the samples is also evident.

Using NMR, XRD and FTIR we clarify the assignment of XP spectra of aluminium phosphates prepared from three different aluminium precursors [Al(OH)₃, Al(NO₃)₃ and AlCl₃] at different annealing temperatures.

Biological behavior of magnesium-substituted hydroxyapatite during bone repair

The aim of this study was to analyze the biological behavior and osteogenic potential of magnesium (Mg) substituted hydroxyapatite (HA) microspheres, implanted in a critical bone defect, considering that this ion is of great clinical interest, since it is closely associated with homeostasis and bone mineralization. For the purpose of this study, 30 rats were used to compose three experimental groups: GI - bone defect filled with HA microspheres; GII - bone defect filled with HA microspheres replaced with Mg; GIII - empty bone defect; evaluated at biological points of 15 and 45 days. The histological results, at 15 days, showed, in all the groups, a discrete chronic inflammatory infiltrate; biomaterials intact and surrounded by connective tissue; and bone neoformation restricted to the borders. At 45 days, in the GI and GII groups, an inflammatory response of discrete granulomatous chronic type was observed, and in the GIII there was a scarce presence of mononuclear inflammatory cells; in GI and GII, the microspheres were seen to be either intact or fragmented, surrounded by fibrous connective tissue rich in blood vessels; and discrete bone neoformation near the edges and surrounding some microspheres. In GIII, the mineralization was limited to the borders and the remaining area was filled by fibrous connective tissue. It was concluded that the biomaterials were biocompatible and osteoconductive, and the percentage of Mg used as replacement ion in the HA did not favor a greater bone neoformation in relation to the HA without the metal.

Injectable Magnesium-Zinc Alloy Containing Hydrogel Complex for Bone Regeneration

Gelatin methacryloyl (GelMA) has been widely used in bone engineering. It can also be filled into the calvarial defects with irregular shape. However, lack of osteoinductive capacity limits its potential as a candidate repair material for calvarial defects. In this study, we developed an injectable magnesium-zinc alloy containing hydrogel complex (Mg-IHC), in which the alloy was fabricated in an atomization process and had small sphere, regular shape, and good fluidity. Mg-IHC can be injected and plastically shaped. After cross-linking, it contents the elastic modulus similar to GelMA, and has inner holes suitable for nutrient transportation. Furthermore, Mg-IHC showed promising biocompatibility according to our evaluations of its cell adhesion, growth status, and proliferating activity. The results of alkaline phosphatase (ALP) activity, ALP staining, alizarin red staining, and real-time polymerase chain reaction (PCR) further indicated that Mg-IHC could significantly promote the osteogenic differentiation of MC3T3-E1 cells and upregulate the genetic expression of collagen I (COL-I), osteocalcin (OCN), and runt-related transcription factor 2 (RUNX2). Finally, after applied to a mouse model of critical-sized calvarial defect, Mg-IHC remarkably enhanced bone formation at the defect site. All of these results suggest that Mg-IHC can promote bone regeneration and can be potentially considered as a candidate for calvarial defect repairing.

Three-dimensional Printed Mg-Doped β-TCP Bone Tissue Engineering Scaffolds: Effects of Magnesium Ion Concentration on Osteogenesis and Angiogenesis In Vitro

Background

Three-dimensional (3D) printed bone tissue engineering scaffolds have been widely used in research and clinical applications. β-TCP is a biomaterial commonly used in bone tissue engineering to treat bone defects, and its multifunctionality can be achieved by co-doping different metal ions. Magnesium doping in biomaterials has been shown to alter physicochemical properties of cells and enhance osteogenesis.

Methods

A series of Mg-doped TCP scaffolds were manufactured by using cryogenic 3D printing technology and sintering. The characteristics of the porous scaffolds, such as microstructure, chemical composition, mechanical properties, apparent porosity, etc., were examined. To further study the role of magnesium ions in simultaneously inducing osteogenesis and angiogenesis, human bone marrow mesenchymal stem cells (hBMSCs) and human umblical vein endothelial cells (HUVECs) were cultured in scaffold extracts to investigate cell proliferation, viability, and expression of osteogenic and angiogenic genes.

Results

The results showed that Mg-doped TCP scaffolds have the advantages of precise design, interconnected porous structure, and similar compressive strength to natural cancellous bone. hBMSCs and HUVECs exhibit high proliferation rate, cell morphology and viability in a certain amount of Mg²⁺. In addition, this concentration of magnesium can also increase the expression levels of osteogenic and angiogenic biomarkers.

Conclusion

A certain concentration of magnesium ions plays an important role in new bone regeneration and reconstruction. It can be used as a simple and effective method to enhance the osteogenesis and angiogenesis of bioceramic scaffolds, and support the development of biomaterials and bone tissue engineering scaffolds.

Single-Phase, Antibacterial Trimagnesium Phosphate Hydrate Coatings on Polyetheretherketone (PEEK) Implants by Rapid Microwave Irradiation Technique

This Article reports the fabrication and evaluation of single-phase, silver-doped trimagnesium phosphate hydrate (Ag-TMPH) nanosheet coatings on polyetheretherketone (PEEK), a well-known material used to fabricate orthopedic and spinal implants. While PEEK has better biomechanical compatibility with bone compared to metallic implants, it is also quite inert. Therefore, it is a common practice to coat PEEK implants with conventional calcium phosphates (CaPs) to enhance cell attachment, proliferation and differentiation. As opposed to well-studied CaP compounds, relatively less-explored magnesium phosphates (MgPs) are also becoming interesting orthopedic biomaterials and is the prime focus in this research. The novel aspects of this paper are as follows. First, we report developing TMPH coatings within minutes with the help of microwave irradiation technology. Microwave irradiation plays an important role in the coating formation with accelerated kinetics. Scanning electron microscopy (SEM) confirmed the fabrication of approximately 650 nm thick TMPH coatings. The coatings resulted in submicron level surface roughness and in vitro cell studies confirmed enhanced MC3T3 cell adhesion within 4 h on such surfaces. The coatings also resulted in significant apatite formation after immersing in simulated body fluid for 7 days. Second, multifunctionality was achieved by doping TMPH coatings with Ag, thus rendering the coatings antibacterial. The antibacterial properties were evaluated against two most common infection-causing bacterial strains-Gram-negative Escherichia coli and Gram-positive Staphylococcus aureus. The results indicated good bacterial resistance and bactericidal properties of the Ag-TMPH coatings. Third, in spite of Ag doping, the single-phase nature of the coatings were retained (without forming composite systems) with the help of the low-processing temperature of the microwave irradiation. The inductive coupled plasma technique confirmed that the doped single-phase TMPH coatings supported a uniform and controlled release of Ag⁺ ions over a period of 3 weeks. MTT assay evaluations and SEM micrographs confirmed no signs of cytotoxicity and healthy proliferation of cells in all cases. Quantitative real time PCR (qRT-PCR) indicated a significant rise in collagen (Col1) and osteocalcin (OCN) gene expression levels in the case of TMPH coated PEEK. Thus, microwave irradiation was successfully employed in forming multifunctional, that is, bioactive, cytocompatible, and antibacterial MgP coatings on PEEK.

Effect of DC Plasma Electrolytic Oxidation on Surface Characteristics and Corrosion Resistance of Zirconium

Zr is a valve metal, the biocompatibility of which is at least on par with Ti. Recently, numerous attempts of the formation of bioactive coatings on Zr by plasma electrolytic oxidation (PEO) in solutions that were based on calcium acetate and calcium β-glycerophosphate were made. In this study, the direct current (DC) PEO of commercially pure zirconium in the solutions that contained Ca(H₂PO₂)₂, Ca(HCOO)₂, and Mg(CH₃COO)₂ was investigated. The treatment was conducted at 75 mA/cm² up to 200, 300, or 400 V. Five process stages were discerned. The treatment at higher voltages resulted in the formation of oxide layers that had Ca/P or (Mg+Ca)/P ratios that were close to that of hydroxyapatite (Ca/P = 1.67), determined by SEM/EDX. The corrosion resistance studies were performed using electrochemical impedance spectroscopy (EIS) and DC polarization methods. R(Q[R(QR)]) circuit model was used to fit the EIS data. In general, the coatings that were obtained at 200 V were the most corrosion resistant, however, they lacked the porous structure, which is typical for PEO coatings, and is sought after in the biomedical applications. The treatment at 400 V resulted in the formation of the coatings that were more corrosion resistant than those that were obtained at 300 V. This was determined mainly by the prevailing plasma regime at the given process voltage. The pitting resistance of Zr was also improved by the treatment, regardless of the applied process conditions.

The Formation Mechanism and Corrosion Resistance of a Composite Phosphate Conversion Film on AM60 Alloy

Magnesium alloy AM60 has high duc and toughness, which is expected to increase in demand for automotive applications. However, it is too active, and coatings have been extensively studied to prevent corrosion. In this work, a Ba-containing composite phosphate film has been prepared on the surface of AM60. The composition and formation mechanism of the film have been investigated using a scanning electronic microscope equipped with energy dispersive X-ray spectroscopy, Fourier transform infrared, X-ray photoelectron spectroscopy, and X-ray diffractometry tests. The corrosion resistance of the film has been measured by electrochemical and immersion tests. The results show that the deposition film has fully covered the substrate but there are some micro-cracks. The structure of the film is complex, and consists of MgHPO₄·3H₂O, MnHPO₄·2.25H₂O, BaHPO₄·3H₂O, BaMg₂(PO₄)₂, Mg₃(PO₄)₂·22H₂O, Ca₃(PO₄)₂·xH₂O, and some amorphous phases. The composite phosphate film has better anticorrosion performance than the AM60 and can protect the bare alloy from corrosion for more than 12 h in 0.6 M NaCl.

Magnesium-based bioceramics in orthopedic applications

Magnesium ions are directly involved in numerous biological mechanisms; for example, they play an important part in the regulation of ion channels, DNA stabilization, enzyme activation and stimulation of cell growth and proliferation. This alkaline earth metal has gained great popularity in orthopedic applications in recent years. Magnesium-based bioceramics include a large group of magnesium containing compounds such as oxides, phosphates and silicates, that are involved in orthopedic applications like bone cements, bone scaffolds or implant coatings. This article aims to give a comprehensive review on different magnesium-based bioceramics, e.g. magnesium phosphates (MgO-P₂O₅), calcium magnesium phosphates (CaO-MgO-P₂O₅), and magnesium glasses (SiO₂-MgO) with a strong focus on the chemistry and properties of magnesium phosphate containing cements as the main application form. In addition, the processing of magnesium phosphate minerals into macroporous scaffolds for tissue engineering applications by either using traditional porogens or by additive manufacturing approaches are reflected. Finally, the biological in vitro and in vivo properties of magnesium phosphates for bone regeneration are summarized, which show promising results regarding the application as bone replacement material, but still lack in terms of testing in large animal models, load-bearing application sites and clinical data.

STATEMENT OF SIGNIFICANCE

Though bone substitutes from calcium phosphates have been investigated for a long time, a new trend is visible in the biomaterials sector: magnesium based bioceramics from magnesium phosphates and silicates due to the special biological significance of magnesium ions in enzymatic activation, cell growth and proliferation, etc. In contrast to pure magnesium implants, such formulations do not release hydrogen during degradation. As with calcium based bioceramics, magnesium based bioceramics are used for the development of diverse applications such as cements, macroporous scaffolds and coatings. From this perspective, we present a systematic overview on diverse kinds of magnesium based bioceramics, their processing regimes for different clinical purposes and their behavior both in vitro and in vivo.

Nanosized strontium substituted hydroxyapatite prepared from egg shell for enhanced biological properties

The fabrication and application of bioactive hydroxyapatite has always been a research hot spot in the fields of orthopaedics. Now it is common to use calcium (Ca) salt as Ca²⁺ source to synthesise hydroxyapatite. And egg shell could be another promising raw material as Ca²⁺ source, which is not only economical but also biogenic. In this study, egg shell (ES)-hydroxyapatite was prepared by using egg shells via hydrothermal method. Furthermore, ES-Sr hydroxyapatite was synthesized by incorporation of bioactive element strontium (Sr²⁺) into ES-hydroxyapatite. The in vitro experiment showed that compared with hydroxyapatite, ES-hydroxyapatite showed better biological performances, which could be attributed to the trace elements in egg shell, such as magnesium (Mg). And the incorporation of Sr²⁺ could further enhance the bioactivity. These results indicated that apatite with high biological activity, which had great application prospects in orthopedics, could be produced by egg shells and the incorporation of Sr²⁺.

Ionic Substitutions in Non-Apatitic Calcium Phosphates

Calcium phosphate materials (CaPs) are similar to inorganic part of human mineralized tissues (i.e., bone, enamel, and dentin). Owing to their high biocompatibility, CaPs, mainly hydroxyapatite (HA), have been investigated for their use in various medical applications. One of the most widely used ways to improve the biological and physicochemical properties of HA is ionic substitution with trace ions. Recent developments in bioceramics have already demonstrated that introducing foreign ions is also possible in other CaPs, such as tricalcium phosphates (amorphous as well as α and β crystalline forms) and brushite. The purpose of this paper is to review recent achievements in the field of non-apatitic CaPs substituted with various ions. Particular attention will be focused on tricalcium phosphates (TCP) and "additives" such as magnesium, zinc, strontium, and silicate ions, all of which have been widely investigated thanks to their important biological role. This review also highlights some of the potential biomedical applications of non-apatitic substituted CaPs.

Effects of sintering temperature on surface morphology/microstructure, in vitro degradability, mineralization and osteoblast response to magnesium phosphate as biomedical material

Magnesium phosphate (MP) was fabricated using a chemical precipitation method, and the biological performances of MP sintered at different temperatures as a biomedical material was investigated. The results indicated that the densification and crystallinity of MP increased as the sintering temperature increased. As the sintering temperature increased, the degradability of MP in PBS decreased, and the mineralization ability in SBF significantly increased. In addition, the MP sintered at 800 °C (MP8) possessed the lowest degradability and highest mineralization ability. Moreover, the positive response of MG63 cells to MP significantly increased as the sintering temperature increased, and MP8 significantly promoted the cell spreading, proliferation, differentiation and expressions of osteogenic differentiation-related genes. Faster degradation of MP0 resulted in higher pH environments and ion concentrations, which led to negative responses to osteoblasts. However, the appropriate degradation of MP8 resulted in suitable pH environments and ion concentrations, which led to positive responses to osteoblasts. This study demonstrated that the sintering temperature substantially affected the surface morphology/microstructure, degradability and mineralization, and osteoblasts response to magnesium phosphate.