Selective adsorption of Mo(VI) ions from aqueous solution using a surface-grafted Mo(VI) ion imprinted polymer

Targeted elimination of molybdenum ions from a leaching solution with the ability of radiated grafting GMA-PAN nanofibers

In this study, electrospun polyacrylonitrile nanofibers were effectively functionalized for enhanced molybdenum ion adsorption through a multi-step approach. Initially, glycidyl methacrylate was grafted onto the nanofibers via irradiation-induced grafting polymerization, followed by chemical modification with various amino groups, with triethylamine identified as the optimal modifier. The impacts of key synthesis parameters and reaction conditions on grafting level and adsorption capacity were thoroughly investigated, with a focus on achieving maximum efficiency. The resulting nanofibers were characterized using FTIR, SEM, and BET techniques, confirming the successful modification and structural features conducive to adsorption. Furthermore, a comprehensive experimental design, incorporating a central composite design, yielded optimal conditions for molybdenum adsorption, with key parameters including monomer concentration, irradiation dose, adsorbent mass, initial concentration, time, pH, temperature, and amine concentration. The adsorption kinetics were effectively described by the pseudo-second-order model, while the Langmuir isotherm model provided valuable insight into the adsorption behavior. Impressively, the adsorbent exhibited exceptional adsorption efficiency, surpassing 98% even after six adsorption-desorption cycles using 0.5 M HCl. Thermodynamic analysis revealed the exothermic nature of the adsorption process, along with decreased entropy and overall spontaneity, underlining the favorable conditions for molybdenum adsorption. Notably, the synthesized adsorbent demonstrated notable selectivity for molybdenum and achieved an impressive adsorption capacity of 109.79 mg/g, highlighting its potential for practical applications in molybdenum removal from aqueous solutions.

Construction of amino-thiol functionalized ion-imprinted chitosan for lead (II) ion removal

Ion-imprinting technique was used to create a lead ion-imprinted sorbent from an amino-thiol chitosan derivative (Pb-ATCS). First, 3-Nitro-4-sulfanylbenzoic acid (NSB) unit's amidized the chitosan, and then the -NO₂-residues were selectively reduced to -NH₂. Imprinting was accomplished by cross-linking with epichlorohydrin and removing the Pb (II) ions from the across-linked polymeric complex formed from the amino-thiol chitosan polymer ligand (ATCS) and Pb (II) ions. The synthetic steps have been investigated by nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FTIR), and the sorbent was tested for its ability to selectively bind Pb (II) ions. The produced Pb-ATCS sorbent had a maximum capacity of roughly 300 mg/g, and it showed a greater affinity for the Pb (II) ions than the control NI-ATCS sorbent particle. The pseudo-2nd-order equation was also consistent with the adsorption kinetics of the sorbent, which were quite rapid. This demonstrated that metal ions were chemo-adsorbed onto the Pb-ATCS and NI-ATCS solid surfaces via coordination with the introduced amino-thiol moieties.

Adsorption Removal of Mo(VI) from an Aqueous Solution by Alumina with the Subsequent Regeneration of the Adsorbent

Industrial wastewater is the main source of an excessive amount of molybdenum (Mo) in natural ecosystems. It is necessary to remove Mo from wastewater before it is discharged into the environment. Molybdate ion(VI) is the most common form of Mo in natural reservoirs and industrial wastewater. In this work, the sorption removal of Mo(VI) from an aqueous medium was evaluated using aluminum oxide. The influence of such factors as the pH of the solution and the temperature was evaluated. Three adsorption isotherms, namely, Langmuir, Freundlich and Temkin, were used to describe the experimental results. It was found that the pseudo-first order kinetic model better fits the kinetic data of the adsorption process, and the maximum Mo(VI) adsorption capacity was 31 mg/g at 25 °C and pH 4. The thermodynamic parameters indicated that the process of Mo(VI) adsorption on Al₂O₃ was exothermic and spontaneous. It was shown that the adsorption of Mo strongly depends on pH. The most effective adsorption was observed at pH values below 7. Experiments on adsorbent regeneration showed that Mo(VI) can be effectively desorbed from the aluminum oxide surface into a phosphate solution in a wide range of pH values. After the desorption of Mo(VI) in a phosphate solution, alumina was found to be suitable for repeating the procedure at least five times.

Adsorption properties and recognition mechanisms of a novel surface imprinted polymer for selective removal of Cu(II)-citrate complexes

Cu(II)-citrate (Cu(II)-CA) complex, as one of the components in plating solutions, increases the difficulty of Cu(II) treatment due to its stable structure and high mobility. In this work, a novel surface imprinted polymer (Cu-CA-SIP) for selective removal of Cu(II)-CA complex from aqueous solution is synthesized by using polyethyleneimine (PEI) grafted onto chloromethylated polystyrene (CMP) microspheres. Cu(II)-CA anions are successfully imprinted with the molar ration of 1:1 by Cu-CA-SIP at initial pH 4.0. Nearly 100% removal rate can be achieved even at low Cu(II)-CA concentration (0.5 mmol/L), and the maximum Cu(II) uptake of Cu-CA-SIP reaches 1.38 mmol/g at 303 K. In Cu(II)/Fe(III)-CA, Cu(II)/Ni(II)-CA, Cu(II)/Zn(II)-CA and Cu(II)/Cd(II)-CA systems, the relative selectivity coefficients of Cu-CA-SIP for Cu(II)-CA are 9.66, 2.32, 1.40 and 44.55, respectively. Moreover, Cu-CA-SIP can be retrieved with negligible loss of adsorption capacity after six times of reuse. The Cu-CA-SIP column can effectively treat the actual electroplating wastewater within 114 BV, and can still reach 104 BV after three dynamic cycles. Therefore, an innovative imprinted material is designed for the first time on the basis of coordination-configuration recognition mechanism for the treatment of electroplating wastewater, providing a new insight in developing surface imprinted polymer in environmental remediation.

Polypyrrole-Bentonite composite as a highly efficient and low cost anionic adsorbent for removing hexavalent molybdenum from wastewater

The aim of current study was to develop a new material for the fast and efficient removal of hexavalent molybdenum (Mo(VI)) from contaminated water. In this work, a novel adsorbent was synthesized through the polypyrrole intercalation modification of bentonite (PPy-BT) via in-situ chemical polymerization method for effectively removal of Mo(VI) from aqueous solution. The surface morphology and chemical composition of PPy-BT composites were investigated by X-ray diffraction, energy-dispersive X-ray spectroscopy, Fourier transform infrared spectrometer, scanning electron microscopy techniques and X-ray photoelectron spectroscopy. PPy and BT could well resist the aggregation of each other, and therefore resulted in a loose-packed structure and good exposure of active sites. Using materials for the adsorption of Mo(VI) revealed has a maximum adsorption capacity of 100.17 mg/g at 25 °C and pH 4.0 by the Langmuir model. The adsorption kinetics and isotherm data are found to be well elucidated through pseudo-second-order and Langmuir models. Moreover, high regeneration ability (>89.3%) of PPy-BT was noted for five consecutive adsorption-desorption cycles. These findings highlight the potential of PPy-BT for practical water treatment applications. The intercalation material of PPy-BT could provide a new strategy to develop cost-effective clay-based nanomaterials for wastewater treatment.

Preparation of chitosan crosslinked with metal-organic framework (MOF-199)@aminated graphene oxide aerogel for the adsorption of formaldehyde gas and methyl orange

Chitosan crosslinked with metal-organic framework (MOF-199)@aminated graphene oxide aerogel (MOF-199@AFGO/CS) were prepared to adsorb formaldehyde and methyl orange. The prepared MOF-199@AFGO/CS aerogel was well characterized via SEM, EDX, FT-IR, XRD and XPS to reveal the microstructure and composition. Besides, the mechanical property and the stability of MOF-199@AFGO/CS aerogel were investigated. The results showed that MOF-199@AFGO/CS aerogel had good stability in water, compression resilience and thermostability. The study on the ability to adsorb formaldehyde gas and methyl orange showed that the adsorption capacity of MOF-199@AFGO/CS aerogel was related to the pore size and the surface functional groups of MOF-199@AFGO/CS aerogel. When the pore size is moderate, as the amino group and MOF-199 on the aerogel increased, the adsorption capacity of formaldehyde gas (197.89 mg/g) and methyl orange (412 mg/g) can reach the maximum. Furthermore, the adsorption process at equilibrium followed the Freundlich isotherm model. The kinetic behavior was well fitted by the pseudo-second-order model, indicating chemisorption as the rate-determining step. This work can provide a reliable basis for the adsorbent to remove pollutants in different forms at the same time, and has potential application in simultaneously adsorbing liquid pollutants and gas pollutants.

Selective and rapid removal of Mo(VI) from water using functionalized Fe3O4-based Mo(VI) ion-imprinted polymer

Fe₃O₄ nanoparticles-based magnetic Mo(VI) surface ion-imprinted polymer (Mo(VI)-MIIP) was elaborated employing 4-vinyl pyridine as a functional monomer. The adsorbent preparation was confirmed by Fourier-transform infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray spectrometry, X-ray diffraction, vibrating sample magnetometer, thermogravimetric analysis, and surface area analysis. Batch adsorption experiments showed that the maximum adsorption capacity of Mo(VI)-MIIP was 296.40 mg g^-1 at pH 3, while that of the magnetic non-imprinted polymer (MNIP) was only 147.10 mg g^-1. The adsorption isotherm model was well fitted by the Langmuir isotherm model. The adsorption experiments revealed that Mo(VI)-MIIP reached adsorption equilibrium within 30 min, and the kinetics data fitting showed that the pseudo-second-order kinetics model suitably described the adsorption process. Mo(VI)-MIIP exhibited an excellent adsorption selectivity to Mo(VI) in binary mixtures of Mo(VI)/Cr(VI), Mo(VI)/Cu(II), Mo(VI)/H₂PO4₄^-, Mo(VI)/Zn(II), and Mo(VI)/I^-, with relative selectivity coefficients toward MNIP of 13.71, 30.27, 20.01, 23.53, and 15.89, respectively. After six consecutive adsorption-desorption cycles, the adsorption capacity of Mo(VI)-MIIP decreased by 9.5% (from 228.4 mg g^-1 to 206.7 mg g^-1 at initial Mo(VI) concentration of 250 mg L^-1), demonstrating its reusability.

A Critical Review on the Synthesis and Application of Ion-Imprinted Polymers for Selective Preconcentration, Speciation, Removal and Determination of Trace and Essential Metals from Different Matrices

The presence of toxic trace metals and high concentrations of essential elements in the environment presents a serious threat to living organism. Various methods have been used for the detection, preconcentration and remediation of these metals from biological, environmental and food matrices. Owing to the complexicity of samples, methods with high selectivity have been used for detection, preconcentration and remediation of these trace metals. These methods are achieved by the use of ion-imprinted polymers (IIPs) due to their impressive properties such as selectivity, high extraction efficiency, speciation capability and reusability. Because of the increase of toxic trace and essential metals in the environment, IIPs have attracted great use in analytical chemistry. This review, provide a brief background on IIPs and polymerization method that are used for their preparation. Recent applications of IIPs as adsorbents for preconcentration, removal, speciation and electrochemical detection of trace and essential metal is also discussed.

PEGylated Thermo-Sensitive Bionic Magnetic Core-Shell Structure Molecularly Imprinted Polymers Based on Halloysite Nanotubes for Specific Adsorption and Separation of Bovine Serum Albumin

Novel PEGylated thermo-sensitive bionic magnetic core-shell structure molecularly imprinted polymers (PMMIPs) for the specific adsorption and separation of bovine serum albumin (BSA) were obtained via a surface-imprinting technique. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), vibrating sample magnetometry (VSM), fourier transform infrared spectrometry (FT-IR), thermal gravimetric analysis (TGA), and specific surface area (BET), were adopted to demonstrate that novel PMMIPs were successfully synthesized. Subsequently, the prepared PMMIPs were used as the extractor for BSA and were combined with magnetic solid-phase extraction. The concentrations of BSA were detected by UV-vis spectrophotometry at 278 nm. The maximum adsorption capacity of the PMMIPs was 258 mg g⁻¹, which is much higher than that of non-imprinted polymer (PMNIPs). PMMIPs showed favorable selectivity for BSA against reference proteins, i.e., bovine hemoglobin, ovalbumin and lysozyme. PMMIPs were further used to recognize BSA in protein mixtures, milk, urine and sewage, these results revealed that approximately 96% of the ideal-state adsorption capacity of PMMIPs for BSA was achieved under complicated conditions. Regeneration and reusability studies demonstrated that adsorption capacity loss of the PMMIPs was not obvious after recycling for four times. Facile synthesis, excellent adsorption property and efficient selectivity for BSA trapping are features that highlight PMMIPs as an attractive candidate for biomacromolecular purification.