Analysis of high performing graphene oxide nanosheets based non-damaging drilling fluids through rheological measurements and CFD studies

Pore-scale flow simulation of supercritical CO2 and oil flow for simultaneous CO2 geo-sequestration and enhanced oil recovery

Recently, carbon capture, utilization, and storage (CCUS) with enhanced oil recovery (EOR) have gained a significant traction in an attempt to reduce greenhouse gas emissions. Information on pore-scale CO₂ fluid behavior is vital for efficient geo-sequestration and EOR. This study scrutinizes the behavior of supercritical CO₂ (sc-CO₂) under different reservoir temperature and pressure conditions through computational fluid dynamics (CFD) analysis, applying it to light and heavy crude oil reservoirs. The effects of reservoir pressure (20 MPa and 40 MPa), reservoir temperature (323 K and 353 K), injection velocities (0.005 m/s, 0.001 m/s, and 0.0005 m/s), and in situ oil properties (835.3 kg/m³ and 984 kg/m³) have been considered as control variables. This study couples the Helmholtz free energy equation (equation of state) to consider the changes in physical properties of sc-CO₂ owing to variations in reservoir pressure and temperature conditions. It has been found that the sc-CO₂ sequestration is more efficient in the case of light oil than heavy oil reservoirs. Notably, an increase in temperature and pressure does not affect the trend of sc-CO₂ breakthrough or oil recovery in the case of a reservoir bearing light oil. For heavy oil reservoirs with high pressures, sc-CO₂ sequestration or oil recovery was higher due to the significant increase in density and viscosity of sc-CO₂. Quantitative analysis showed that the stabilizing factor (ε) appreciably varies for light oil at low velocities while higher sensitivity was displayed for heavy oil at high velocities.

Nanofluid Formulations Based on Two-Dimensional Nanoparticles, Their Performance, and Potential Application as Water-Based Drilling Fluids

The development of sustainable, cost-efficient, and high-performance nanofluids is one of the current research topics within drilling applications. The inclusion of tailorable nanoparticles offers the possibility of formulating water-based fluids with enhanced properties, providing unprecedented opportunities in the energy, oil, gas, water, or infrastructure industries. In this work, the most recent and relevant findings related with the development of customizable nanofluids are discussed, focusing on those based on the incorporation of 2D (two-dimensional) nanoparticles and environmentally friendly precursors. The advantages and drawbacks of using 2D layered nanomaterials including but not limited to silicon nano-glass flakes, graphene, MoS₂, disk-shaped Laponite nanoparticles, layered magnesium aluminum silicate nanoparticles, and nanolayered organo-montmorillonite are presented. The current formulation approaches are listed, as well as their physicochemical characterization: rheology, viscoelastic properties, and filtration properties (fluid losses). The most influential factors affecting the drilling fluid performance, such as the pH, temperature, ionic strength interaction, and pressure, are also debated. Finally, an overview about the simulation at the microscale of fluids flux in porous media is presented, aiming to illustrate the approaches that could be taken to supplement the experimental efforts to research the performance of drilling muds. The information discussed shows that the addition of 2D nanolayered structures to drilling fluids promotes a substantial improvement in the rheological, viscoelastic, and filtration properties, additionally contributing to cuttings removal, and wellbore stability and strengthening. This also offers a unique opportunity to modulate and improve the thermal and lubrication properties of the fluids, which is highly appealing during drilling operations.

Research progress on the effects of nanoparticles on gas hydrate formation

Gas hydrate has great application potential in gas separation, energy storage, seawater desalination, etc. However, the intensity of mass and heat transfer is not enough to meet the needs of efficient hydrate synthesis. Nanoparticles, different from other liquid chemical additives, are considered as effective additives to promote hydrate formation due to their rich specific surface area and excellent thermal conductivity. This work summarizes the effect of the nanoparticles on the thermodynamics and kinetics of hydrate formation. And also, this work probes into the mechanism of the effect of the nanoparticles on the formation of hydrate as well as provides some suggestions for future research. It is found that it's difficult for nanoparticles to effectively promote the formation of the gas hydrate without the use of surfactants, because the adhesion characteristics of the nanoparticles make them easily agglomerate or even agglomerate in solution. In addition, at present, the research on the influence of nanoparticles on the formation and decomposition of natural gas hydrate is still very fragmented, and the micro mechanism of the influence is not clear, which requires more systematic and specific research in the future. At the same time, the development of nanoparticles that can promote the formation of natural gas hydrate should also become the focus of future research.

The use of nanoparticles and their effects on thermodynamics and kinetics during the hydrate formation process is summarized. For their application in drilling fluid and cement slurry, it is found nanoparticles must be used in conjunction with surfactants to be effective.

A comparative study between two novel silicone/graphene-based nanostructured surfaces for maritime antifouling

Two novel superhydrophobic nanocomposite series of polydimethylsiloxane (PDMS) enriched with reduced graphene oxide (RGO) and graphene oxide/boehmite nanorods (GO-γ-AlOOH) nanofillers were synthesized as maritime fouling-release (FR) surfaces. Controlling the nanofillers' structures and distribution in the silicone matrix influenced the self-cleaning and antifouling properties. γ-AlOOH nanorods had a single crystallinity with an average diameter of 10-20 nm and < 200 nm length. A hydrothermal method was used to prepare RGO, while the chemical deposition method was used to synthesis GO-γ-AlOOH nanocomposites for use as fouling-release coating materials. For studying the synergetic effects of graphene-based materials on the surface, mechanical, and FR features, these nanofillers were dispersed in the silicone matrix using the solution casting method. The hydrophobicity and antifouling properties of the surface were studied using water contact angle (WCA), scanning electron, and atomic force microscopes (SEM and AFM). Coatings' roughness, superhydrophobicity, and surface mechanical properties all improved for the homogeneity of the dispersion of the nanocomposite. Laboratory assessments were carried out for 30 days using selected microorganisms to determine the antifouling effects of the coating systems. PDMS/GO-γ-AlOOH nanorod composite had better antibacterial activity than PDMS/RGO nanocomposite against different bacterial strains. This is caused by the high surface area and stabilizing effects of the GO-γ-AlOOH hybrid nanofillers. The PDMS/GO-γ-AlOOH nanorod composite (3 wt%) had the lowest biodegradability percentage (1.6%) and the microbial endurability percentages for gram-positive, gram-negative, and fungi were 86.42%, 97.94%, and 85.97%, respectively. A field trial in natural seawater was conducted to confirm the coatings' FR performance based on the screening process and image analysis for 45 days in a tropical area. The most profound superhydrophobic antifouling nanostructured coating was the homogeneity of the GO-γ-AlOOH (3 wt%) dispersion, which had a WCA of 151° and a rough surface.

Utilization of Eco-Friendly Waste Generated Nanomaterials in Water-Based Drilling Fluids; State of the Art Review

An important aspect of hydrocarbon drilling is the usage of drilling fluids, which remove drill cuttings and stabilize the wellbore to provide better filtration. To stabilize these properties, several additives are used in drilling fluids that provide satisfactory rheological and filtration properties. However, commonly used additives are environmentally hazardous; when drilling fluids are disposed after drilling operations, they are discarded with the drill cuttings and additives into water sources and causes unwanted pollution. Therefore, these additives should be substituted with additives that are environmental friendly and provide superior performance. In this regard, biodegradable additives are required for future research. This review investigates the role of various bio-wastes as potential additives to be used in water-based drilling fluids. Furthermore, utilization of these waste-derived nanomaterials is summarized for rheology and lubricity tests. Finally, sufficient rheological and filtration examinations were carried out on water-based drilling fluids to evaluate the effect of wastes as additives on the performance of drilling fluids.