Cesium removal in freshwater using potassium cobalt hexacyanoferrate-impregnated fibers

Cesium ion adsorption and desorption on electrospun mesoporous silica nanofibers immobilized with Prussian blue

To fabricate an efficient Cs ion adsorbent and prevent unexpected loss of Prussian blue (PB) colloidal particles during use, PB was immobilized on the surface of electrospun mesoporous silica nanofibers (MSFs) via a newly developed method of double exposure to Fe (III) ions. To introduce PB on MSFs, the MSFs were functionalized with ethylenediamine moiety to bind to Fe (III) ions, which would firmly anchor PB. MSFs were pretreated with Fe (III) ions and exposed to K₄ [Fe(II) (CN)₆] to form PB. We found that this process did not provide a sufficient PB amount on the MSFs. To increase the PB amount, after initial PB formation, the MSFs were treated with Fe (III) ions again so that the unreacted K₄ [Fe(II) (CN)₆] remaining on the MSFs could become PB. An investigation of the adsorption isotherms and kinetics of the nanofibrous adsorbent indicated that monolayer chemisorption had occurred. The maximum Cs ion adsorption capacity using the method of double exposure to Fe (III) ions was determined to be 14.66 mg/g, which was higher by a factor of 2.24 than the case that was not prepared by this method. Cs ions were selectively adsorbed over other cations and could be removed in both acidic and basic conditions, presumably because of the robust MSFs.

Sorption methods in marine radiochemistry

The review presents the general methodology of using sorption methods to solve problems of marine radiochemistry, including sampling, preconcentration and radiochemical preparation and methods for measuring the activity of radionuclides. The possible methodological errors at various stages of sampling and sample concentration are discussed. The most widely used artificial (90Sr, 134Cs, 137Cs, 239Pu, 240Pu), natural (210Pb, 210Po; radium quartet: 223Ra, 224Ra, 226Ra, 228Ra; thorium isotopes, mainly 234Th) and cosmogenic (7Be, 32P, 33P) radiotracers are considered. The sorption of uranium from seawater is not addressed, since its concentration in seawater is usually calculated from the known dependence of uranium concentration on seawater salinity.

The bibliography includes 200 references.

A comparative study of immobilizing ammonium molybdophosphate onto cellulose microsphere by radiation post-grafting and hybrid grafting for cesium removal

Ammonium molybdophosphate (AMP) exhibits high selectivity towards Cs but it cannot be directly applied in column packing, so it is necessary to prepare AMP-based adsorbents into an available form to improve its practicality. This work provided two AMP immobilized cellulose microspheres (MCC@AMP and MCC-g-AMP) as adsorbents for Cs removal by radiation grafting technique. MCC-g-AMP was prepared by radiation graft polymerization of GMA on microcrystalline cellulose microspheres (MCC) followed by reaction with AMP suspension, and MCC@AMP was synthesized by radiation hybrid grafting of AMP and GMA onto MCC through one step. The different structures and morphologies of two adsorbents were characterized by FTIR and SEM. The adsorption properties of two adsorbents against Cs were investigated and compared in batch and column experiments under different conditions. Both adsorbents were better obeyed pseudo-second-order kinetic model and Langmuir model. MCC-g-AMP presented faster adsorption kinetic and more stable structure, whereas MCC@AMP presented more facile synthesis and higher adsorption capacity. MCC@AMP was pH independent in the range of pH 1-12 but MCC-g-AMP was sensitive to pH for Cs removal. The saturated column adsorption capacities of MCC@AMP and MCC-g-AMP were 5.4 g-Cs/L-ad and 0.75 g-Cs/L-ad in column adsorption experiments at SV 10 h-1. Both adsorbents exhibited very high radiation stability and can maintain an adsorption capacity of >85% even after 1000 kGy γ-irradiation. On the basis, two AMP-loaded adsorbents possessed promising application in removal of Cs from actual contaminated groundwater. These findings provided two efficient adsorbents for treatment of Cs in radioactive waste disposal.

Natural and anthropogenic radionuclides in water and wastewater: Sources, treatments and recoveries

Water-energy nexus in the context of changing climate amplifies the importance of comprehending the transport, fate and recovery of radioisotope. While countries have been more interested for zero/low greenhouse gas emission technologies, energy production from nuclear power plant (NPP) can be a prominent solution. Moreover, radioisotopes are also used for other benefits such as in medical science, industrial activities and many more. These radionuclides are blended accidently or intentionally with water or wastewater because of inefficacious management of the nuclear waste; and therefore, it is an imperative task to manage nuclear waste so that the harmful consequences of the waste on environment, ecology and human health can be dispelled. Due to generation of significant amount of waste throughout its utilization, a noticeable number of physical, chemical and biological processes has been introduced as remediation processes although mechanisms of optimum removal process are still under investigation. Removal mechanisms and influencing factors for radionuclide removal are elucidated in this review so that, further, operation and process development can be promoted. Again, resource recovery, opportunities and challenges are also discussed for elevating the removal rates and minimizing the knowledge gaps existing in development and applications of novel decontamination processes.

CAESIUM RETENTION CHARACTERISTICS OF KNIFC-PAN RESIN FROM RIVER WATER

The caesium retention characteristics of a potassium-nickel hexacyanoferrate resin in a polyacrylnitrile (KNiFC-PAN) matrix were tested in fresh water over the range of 2.5-400 mL min-1. The experimental setup used 2 mL resin and 4-L aliquots of freshwater samples. The results showed nearly 100% retention at speeds below 10 mL min-1, above 80% up to 100 mL min-1, and approached 50% at 400 mL min-1. Using 100 mL min-1 flow rate and KNiFC-PAN resin in a well-type HPGe detector, the minimum detectable concentration was reduced to 3 mBq kg-1 for 4-L aliquots of water samples from the previous 15 mBq kg-1 achieved by Powdex ion-exchange resin and a planar type HPGe detector.

Stabilization of Prussian blue using copper sulfate for eliminating radioactive cesium from a high pH solution and seawater

Prussian blue (PB), an adsorbent for the selective elimination of radioactive cesium from water, is highly versatile due to its unique crystal structure. However, PB crystals quickly decompose in an alkaline solution, generating hazardous cyanide contamination. In this research, the alkaline susceptibility of PB was remedied by incorporating copper sulfate as a protector. A stability assessment was conducted at several environmental conditions, such as high pH and temperatures from 10 °C to 50 °C, in seawater, artificial seawater, and river water. The crystalline and chemical stability of PB in the new class of composite was extremely high, even at a pH value of 11.2, as confirmed using XRD and total cyanide analysis. A comprehensive mechanism study revealed that, at high pH, the copper ions that cover the PB react with hydroxide ions to form copper hydroxide and shielding inner crystals. To decontaminate radioactive cesium, the first step was to immobilize nano PB on a cellulose nanofiber, followed by copper sulfate stabilization. Then, a spongiform adsorbent was made using polyurethane as the precursor. The new stabilized PB showed promising adsorption efficiency. Thus, this research will open a new range of applications for all existing and emerging PB-based adsorbents.

Prussian blue nanocubes decorated on nitrogen-doped hierarchically porous carbon network for efficient sorption of radioactive cesium

Eliminating the radioactive ¹³⁷Cs from nuclear waste is critical to the human health and environment. Prussian blue (PB)-based materials are considered as promising adsorbents for the removal of cesium. Herein, we demonstrate a facile strategy to achieve controllable synthesis of PB nanocrystals decorated on nitrogen-doped hierarchically porous carbon (NHPC) derived from cattle bone as adsorbent to remove cesium. The PB nanocrystals with a nanocube morphology are well distributed on NHPC, which is beneficial to increase the reachable surface area during adsorption. The resulting adsorbent exhibits a remarkable adsorption performance with a capacity of 125.31 mg g^-1, a superior recyclability with 87 % of initial capacity retained after 5 cycles, and an outstanding adsorption selectivity for cesium. X-ray diffraction, X-ray photoelectron spectroscopy combined with ⁵⁷Fe Mössbauer spectroscopy results reveal that cesium ions are inserted into the crystal channels of PB to generate a new phase (CsFe₂(CN)₆·3H₂O) after adsorption. Moreover, the adsorption process is spontaneous and endothermic which can be described by the Langmuir isotherm and pseudo-second-order kinetic models. This strategy for synthesis of PB/carbon adsorbents offers efficient candidate for removal of ¹³⁷Cs from wastewater.

Chemically bound Prussian blue in sodium alginate hydrogel for enhanced removal of Cs ions

A new approach for efficient removal of radioactive ¹³⁷Cs was developed using a sodium alginate hydrogel beads-based adsorbent containing chemically bound Prussian blue (PB). Sodium alginate was crosslinked with Fe (III) ions to form hydrogel beads, in which Fe (III) had a dual function; it served as a crosslinking agent and also led to PB formation via reaction with hexacyanoferrate. Fe (III) ions, an unusual crosslinking agent for sodium alginate gel, led to stable, homogeneous distribution of PB inside the beads. The amount of embedded PB in the composite beads was more than two times larger than in the conventional sodium alginate-PB composite beads, resulting in an adsorption capacity for Cs ions that was two to five times higher, mainly because of a higher PB contents and because of the microporosity of the sodium alginate hydrogel.

Enhanced cesium removal from real matrices by nickel-hexacyanoferrate modified activated carbons

After nuclear disasters, radioactive cesium partitions to soils and surface water, where it decays slowly. Hexacyanoferrates (HCFs) have excellent cesium removal properties but their structure is typically powdery. Many carrier materials, such as biomass or magnetic particles, have been used to provide a suitable substrate for HCFs that can be used in filters. This research uses the sorption properties of activated carbon (AC) to incorporate Ni-HCF, resulting in good structural properties of the hybrid material. These HCF-modified ACs show drastically improved sorption properties towards Cs after one, two and three HCF impregnation cycles. The activated carbon from brewer's spent grain with one modification cycle removes more than 80% of 1 mg L^-1 Cs in a sea water solution and more than 98% of 1 mg L^-1 Cs from surface water at a low AC dosage (0.5 g L^-1). Iron and nickel leaching is studied and found to be dependent on the type of modified AC used and the leaching solution. Iron leaching can be problematic in surface and seawater, whereas nickel leaching is especially pronounced in seawater.