Surface-enhanced Raman scattering detection of silver nanoparticles in environmental and biological samples

Development of a portable SERS tool to evaluate the effectiveness of washing methods to remove pesticide residue from fruit surface

BACKGROUND

Pesticides are widely used in agriculture to control pests and enhance crop yields. However, post-harvest, there are growing concerns about the potential health risks posed by pesticide residues on produce surfaces. Analyzing these residues is challenging due to their typically low concentrations and the potential interference from the complex matrix of the produce's surface. The problem addressed in this study is the need for a sensitive, rapid, and on-site capable method to detect and quantify pesticide residues on agricultural products.

RESULTS

We developed a portable surface-enhanced Raman spectrometer (SERS)-based approach that offers a rapid 10-min turnaround, simplified protocol, on-site capability, and high sensitivity. Using the new analytical method, we evaluated pesticide residues on fruit surfaces after household or industrial postharvest washing, specifically the efficacy in removing the fungicide ferbam from peach surfaces. The limit of detection (LOD) for our method was determined to be 0.012 mg/kg, significantly lower than the U.S. Environmental Protection Agency's regulated limit of 7 mg/kg for ferbam on peaches. Our data shows that soaking in tap water for 1 min is the least effective method for removing ferbam, with insignificant difference from the control group. In contrast, soaking in a vinegar-water or NaHCO3-water solution for 5 min, as well as in a sodium hypochlorite solution (12 % available chlorine) for 1 or 5 min, proved to be the most effective methods. Extended soaking improved pesticide removal for tap water, vinegar, and NaHCO3, while in the chlorine groups, the effect was insignificant. SERS analysis revealed negligible penetration of ferbam into peach flesh and the inner surface of the skin.

SIGNIFICANCE

This study introduces an innovative method for measuring pesticide residues, significantly enhancing our understanding of pesticide removal and penetration. This new analytical approach is crucial for effectively detecting pesticides and mitigating their exposure through food sources.

Adhesive surface-enhanced Raman scattering Cu-Au nanoassembly for the sensitive analysis of particulate matter

Surface-enhanced Raman scattering (SERS) has been used in atmospheric aerosol detection as it enables the high-resolution analysis of particulate matter. However, its use in the detection of historical samples without damaging the sampling membrane while achieving effective transfer and the high-sensitivity analysis of particulate matter from sample films remains challenging. In this study, a new type of SERS tape was developed, consisting of Au nanoparticles (NPs) on an adhesive double-sided Cu film (DCu). The enhanced electromagnetic field generated by the coupled resonance of the local surface plasmon resonances of AuNPs and DCu led to an enhanced SERS signal with an experimental enhancement factor of 10⁷. The AuNPs were semi-embedded and distributed on the substrate, and the viscous DCu layer was exposed, enabling particle transfer. The substrates exhibited good uniformity and favorable reproducibility with relative standard deviations of 13.53% and 9.74% respectively, and the substrates could be stored for 180 days with no signs of signal weakening. The application of the substrates was demonstrated by the extraction and detection of malachite green and ammonium salt particulate matter. The results demonstrated that SERS substrates based on AuNPs and DCu are highly promising in real-world environmental particle monitoring and detection.

Rapid Detection of Ag(I) via Size-Induced Photoluminescence Quenching of Biocompatible Green-Emitting, l-Tryptophan-Scaffolded Copper Nanoclusters

Atomically precise metal nanoclusters capped with small molecules like amino acids are highly favored due to their specific interactions and easy incorporation into biological systems. However, they are rarely explored due to the challenge of surface functionalization of nanoclusters with small molecules. Herein, we report the synthesis of a green-emitting (λex = 380 nm, λem = 500 nm), single-amino-acid (l-tryptophan)-scaffolded copper nanocluster (Trp-Cu NC) via a one-pot route under mild reaction conditions. The synthesized nanocluster can be used for the rapid detection of a heavy metal, silver (Ag(I)), in the nanomolar concentration range in real environmental and biological samples. The strong green photoluminescence intensity of the nanocluster quenched significantly upon the addition of Ag(I) due to the formation of bigger nanoparticles, thereby losing its energy quantization. A notable color change from light yellow to reddish-brown can also be observed in the presence of Ag(I), allowing its visual colorimetric detection. Portable paper strips fabricated with the Trp-Cu NC can be reliably used for on-site visual detection of Ag(I) in the micromolar concentration range. The Trp-Cu NC possesses excellent biocompatibility, making it a suitable nanoprobe for cell imaging; thus, it can act as an in vivo biomarker. The nanocluster showed a significant spectral overlap with anticancer drug doxorubicin and thus can be used as an effective fluorescence resonance energy transfer (FRET) pair. FRET results can reveal important information regarding the attachment of the drug to the nanocluster and hence its role as a potential drug carrier for targeted drug delivery within the human body.

Surface-enhanced Raman spectroscopy for environmental monitoring using gold clusters anchored on reduced graphene oxide

Surface-enhanced Raman spectroscopy is a strong and sensitive analysis tool that can realize single-molecule level detection and provide the fingerprint information of molecules, which has been widely applied in analysing chemistry and biomolecules and monitoring environment. However, it is still a challenge to design and prepare SERS substrates with high enhancement factor, simple synthesis, stability and reproducibility. Here, we synthesized gold clusters anchored on reduced graphene oxide (Au clusters@rGO) using co-reduction method to achieve high SERS enhancement. The substrate of gold clusters anchored on reduced graphene oxide combines the chemical enhancement of reduced graphene oxide and the electromagnetic enhancement of gold clusters, leading to an ultrahigh enhancement factor of 3.5 × 10⁷. The efficient SERS was ascribed to the high localized surface plasmon resonance (LSPR) of aggregations of gold clusters, the synergistic effect of gold clusters and reduced graphene oxide, and the charge transfer between graphene and the molecules. This research will provide an invaluable strategy to design and prepare superior-property SERS substrates.

Surface-enhanced Raman spectroscopy for studying the interaction of N-propyl substituted imidazole compound with salmon sperm DNA

BACKGROUND

Surface Enhanced Raman Spectroscopy (SERS) is a very promising and fast technique for studying drugs and for detecting chemical nature of a molecule and DNA interaction. In the current study, SERS is employed to check the interaction of different concentrations of n-propyl imidazole derivative ligand with salmon sperm DNA using silver nanoparticles as SERS substrates.

OBJECTIVES

Multivariate data analysis technique like principal component analysis (PCA) and partial least squares-discriminant analysis (PLS-DA) are employed for the detailed analysis of the SERS spectral features associated with the mode of action of the imidazole derivative ligand with DNA.

METHODOLOGY

Silver nanoparticles were used as a SERS substrate in DNA-drug interaction. Five different concentrations of ligands were interacted with DNA and mix with Ag-NPs as substrate. The SERS spectra of were acquired for all seven samples and processed using MATLAB. Additionally, PCA and PLS-DA were used to assessed the ability SERS to differentiate interaction of DNA-drug.

RESULTS

Differentiating SERS features having changes in their peak position and intensities are observed including 629, 655, 791, 807, 859, 1337, 1377 and 1456 cm^-1. These SERS features reveal that binding of ligand with DNA is electrostatic in nature, and have specificity to major groove where it forms GC-CG interstrand cross-linking with the DNA double helix.

CONCLUSIONS

SERS give significant information regarding to Drug-DNA interaction mechanism, SERS spectra inferred the mode of action of anticancer compound that are imidazole in nature.

Reduction of Ionic Silver by Sulfur Dioxide as a Source of Silver Nanoparticles in the Environment

The natural formation of silver nanoparticles (AgNPs) via biotic and abiotic pathways in water and soil media contributes to the biogeochemical cycle of silver metal in the environment. However, the formation of AgNPs in the atmosphere has not been reported. Here, we describe a previously unreported source of AgNPs via the reduction of Ag(I) by SO₂ in the atmosphere, especially in moist environments, using multipronged advanced analytical and surface techniques. The rapid reduction of Ag(I) in the atmospheric aqueous phase was mainly caused by the sulfite ions formed from the dissolution of SO₂ in water, which contributed to the formation of AgNPs and was consistent with the Finke-Watzky model with a major contribution of the reduction-nucleation process. Sunlight irradiation excited SO₂ to form triplet SO₂, which reacted with water to form H₂SO₃ and greatly enhanced Ag(I) reduction and AgNP formation. Different pH values affected the speciation of Ag(I) and S(IV), which were jointly involved in the reduction of Ag(I). The formation of AgNPs was also observed in the atmospheric gas phase via direct reduction of Ag(I) by SO₂(gas), which occurred even in 50 ppbv SO₂(gas). The natural occurrence of AgNPs in the atmosphere may also be involved in silver corrosion, AgNP transformation and regeneration, detoxification of gaseous pollutants, and the sulfur cycle in the environment.

Incidence of metal-based nanoparticles in the conventional wastewater treatment process

Metal-based nanoparticles (NPs) can be found in wastewater streams, which are significant pathways for the release of NPs to the environment. Determination of the NPs concentration in wastewater streams is important for performing appropriate ecotoxicological evaluations. The aim of this work was to determine the incidence of NPs from 13 different elements throughout the wastewater treatment process by using single particle inductively coupled plasma mass spectrometry (spICP-MS). The incidence was determined in samples of the influent, post-primary treatment and effluent of the activated sludge process, as well as in the reclaimed water of a full-scale wastewater treatment plant (WWTP). In addition, concentration of NPs was determined in the waste activated sludge and in the anaerobic digester. The concentration of metal-based NPs in the influent wastewater were between 1,600 and 10,700 ng/L for elements such as Ti, Fe, Ce, Mg, Zn and Cu, while that for Ni, Al, Ag, Au, Co and Cd was below 100 ng/L. Concentrations in reclaimed water ranged between 0.6 and 721 ng/L, ranked as Mg > Ti > Fe > Cu > Ni > Ce > Zn > Mn > Al  > Co > Ag > Cd  > Au. Results indicated that the activated sludge process and reclaimed water system removed 84-99% of natural and engineered metal-based NPs from influent to reclaimed water, except for Mg, Ni and Cd where the removal ranged from 70 to 78%. The highest concentrations of NPs were found in the waste activated sludge and anaerobic sludge, ranging from 0.5 to 39,900 ng/L. The size distribution of NPs differed in different wastewater streams within the WWTP, resulting in smaller particles in the effluent (20-180 nm) than in the influent (23-233 nm) for most elements. Conversely, NPs were notably larger in the waste activated sludge samples than in the anaerobic sludge or wastewater, since conditions in the secondary treatment lead to precipitation of several metal-based NPs. The incidence of metal-based NPs from 13 elements in wastewater decreased significatively after the conventional wastewater treatment train. However, anaerobic digesters store high NPs concentrations. Hence, the disposal of sludge needs to take this into account to evaluate the risk of the release of NPs to the environment.

Surface Enhanced Raman Spectroscopy in environmental analysis, monitoring and assessment

Environmental pollution is usually monitored via mass spectrometry-based approaches. Such techniques are extremely sensitive but have several disadvantages. The instruments themselves are expensive, require specialized training to use and usually cannot be taken into the field. Samples also usually require extensive pre-treatment prior to analysis which can affect the final result. The development of analytical methods that matched the sensitively of mass spectrometry but that could be deployed in the field and require minimal sample processing would be highly advantageous for environmental monitoring. One method that may meet these criteria is Surface Enhanced Raman Spectroscopy (SERS). This is a surface-sensitive technique that enhances Raman scattering by molecules adsorbed on rough nanostructure surfaces such as gold or silver nanoparticles. SERS gives selective spectral enhancement such that increases in sensitivity of 10¹⁰ to 10¹⁴ have been reported. While this means SERS is, theoretically at least, capable of single molecule detection such a signal enhancement is hard to achieve in practice. In this review the background of SERS is introduced for the environmental scientist and the recent literature on the detection of several classes of environmental pollutants using this technique is discussed. For heavy metals the lowest limit of detection reported was 0.45 μg/L for Mercury; for pharmaceuticals, 2.4 μg/L for propranolol; for endocrine disruptors, 0.35 μg/L for 17β-estradiol; for perfluorinated compounds, 500 μg/L for perfluorooctanoic acid and for inorganic pollutants, 37g/L for general pesticide markers. The signal enhancements achieved in each case show great promise for the detection of pollutants at environmentally relevant concentrations and, although it does not yet routinely match the sensitivity of mass spectrometry. Further work to develop SERS methods and apply them for the detection of contaminants could be of wide benefit for environmental science.

Silver nanoparticles in dye effluent treatment: A review on synthesis, treatment methods, mechanisms, photocatalytic degradation, toxic effects and mitigation of toxicity

The current scenario of water resources shows the dominance of pollution caused by the draining of industrial effluents. The polluted waters have resulted in severe health and environmental hazards urging for a suitable alternative to resolve the implications. Various physical and chemical treatment steps currently in use for dye effluent treatment are more time consuming, cost-intensive, and less effective. Alternatively, nanoparticles due to their excellent surface properties and chemical reactivity have emerged as a better solution for dye removal and degradation. In this regard, the potential of silver nanoparticles in dye effluent treatment was greatly explored. Efforts were taken to unravel the kinetics and statistical optimization of the treatment conditions for the efficient removal of dyes. In addition, the role of silver nanocomposites has also experimented with colossal success. On the contrary, studies have also recognized the mechanisms of silver nanoparticle-mediated toxicity even at deficient concentrations and their deleterious biological effects when present in treated water. Hence, the fate of the silver nanoparticles released into the treated water and sludge, contaminating the soil, aquatic environment, and underground water is of significant concern. This review summarizes the current state of knowledge regarding the use of silver nanoparticles and silver-based nanocomposites in effluent treatment and comprehends the recent research on mitigation of silver nanoparticle-induced toxicity.

SERS using two-photon polymerized nanostructures for mycotoxin detection

Improved chemical- and bio-sensing with Surface Enhanced Raman Spectroscopy (SERS) requires nanostuctures that can be flexibly designed and fabricated with different physical and optical properties. Here, we present nano-pillar arrays ranging from 200 nm to 600 nm as SERS substrates for mycotoxin detection that are fabricated by means of two-photon polymerization. We built a nominal shape and a voxel-based model for simulating the enhancement of the electric field of the nano-pillar arrays using the Finite-Difference Time-Domain (FDTD) method. A new model was built based on the Atomic Force Microscopy (AFM) data obtained from the fabricated nanostructures and introduced into a FDTD model. We demonstrated the enhancement behavior by measuring the Raman spectrum of Rhodamine B solutions. Both the simulations and experimental results suggest that the 200 nm nano-pillar array has the highest Enhancement Factor (EF). Besides, we determined the limit of detection of the 200 nm pillar array by performing Raman measurements on Rhodamine B solutions with different concentrations. The detection limit of our 200 nm nano-pillar array is 0.55 μM. Finally we discriminated 1 ppm deoxynivalenol and 1.25 ppm fumonisin b1 in acetonitrile solutions by our SERS substrate in combination with principal component analysis. This versatile approach for SERS substrates fabrication gives new opportunities for material characterization in chemical and biological applications.

Nano-pillar arrays are presented ranging from 200 nm to 600 nm as SERS substrates for mycotoxin detection, fabricated by two-photon polymerization. This versatile approach gives new opportunities for material characterization in chemical and biological applications.

Recent progress in nanomaterial-based electrochemical biosensors for pathogenic bacteria

This review (with 118 refs.) discusses the progress made in electroanalytical methods based on the use of organic and inorganic nanomaterials for the determination of bacteria, specifically of E. coli, Salmonella, Staphylococcus, Mycobacterium, Listeria and Klebsiella species. We also discuss advantages and limitations of electrochemical methods. Strategies based on the use of aptamers, DNA and antibodies are covered. Following an introduction into electrochemical biosensing, a first large section covers methods for pathogen detection using metal nanoparticles, with subsections on silver nanoparticles, gold nanoparticles, magnetic nanoparticles and carbon-based nanomaterials. A second large section covers methods based on the use of organic nanocomposites, graphene and its derivatives. Other nanoparticles are treated in a final section. Several tables are presented that give an overview on the wealth of methods and materials. A concluding section summarizes the current status, addresses challenges, and gives an outlook on potential future trends. Graphical abstract This review demonstrates the progress made in electroanalytical methods based on the use of organic and inorganic nanomaterials for the detection and determination of pathogenic bacteria. We also discuss advantages and limitations of electrochemical methods. Strategies based on the use of aptamers, DNA and antibodies are covered.

Incidence and persistence of silver nanoparticles throughout the wastewater treatment process

While the predicted or observed concentrations of Ag NPs in wastewater treatment plants (WWTPs) have ranged from μg/L to ng/L, there is still uncertainty with regards to the realistic concentration range of Ag NPs in WWTPs. In addition, the persistence, removal, and size of Ag NPs throughout WWTP process is also not well investigated, particularly in real operating conditions. In this study, the incidence and persistence of Ag NPs in the wastewater process were studied by using single particle inductively coupled plasma mass spectrometry (sp-ICP-MS). The incidence of Ag NPs was determined in samples collected at the influent and effluent of the conventional process, as well as reclaimed and backwash waters of the ultrafiltration (UF) system in a WWTP (Santa Barbara, CA), showing a concentration of 13.5, 3.2, 0.5 and 9.8 ng/L, respectively, with relative standard deviations (RSDs) < 5%. Total Ag concentration (Ag NP and Ag⁺) ranged from 40 to 70 ng/L, in line with lower predicted values. Most of the Ag NPs detected were below 100 nm, with a few above 100 nm in the conventional effluent. Biological and physical processes in the secondary treatment removed 76.3% of the colloidal Ag fraction, while with the tertiary treatment (UF) the WWTP achieved a removal of 96.3% of the colloidal fraction. Persistence of Ag NPs in various water matrixes, including a synthetic wastewater (SWW), was determined by spiking 300 ng/L of Ag NPs (40 nm) and monitoring the concentrations and size change for 15 days. The persistence of Ag NPs in suspension was Influent > Effluent > Reclaimed > SWW. Partial dissolution of NPs in all waters was observed from time 0 h. Although the current concentrations in the outlet flows from WWTP (effluent and reclaimed waters) were low, the presence of small and stable Ag NPs may raise ecotoxicological concerns via bioaccumulation.

A field-deployable surface-enhanced Raman scattering (SERS) method for sensitive analysis of silver nanoparticles in environmental waters

The proliferation of silver nanoparticles (AgNPs) in the environment and resultant transport into aquatic systems have raised concerns regarding their potential toxicity to various organisms. These environmental and ecological concerns demand reliable AgNP detection methods which can measure environmentally relevant quantities of AgNPs in real aquatic systems. This study developed a method that couples a rapid vacuum filtration technique with a portable Raman spectrometer to achieve on-site detection of ultra-low levels of AgNPs in typical and complex aquatic systems. To extract and detect AgNPs, aluminum chloride and ferbam were added for AgNP aggregation and labelling, respectively. The AgNP aggregates were filtered through a membrane, and their presence and quantity were determined based upon the surface-enhanced Raman scattering (SERS) peak intensity of ferbam. Under the optimized conditions, the extraction efficiencies are 99 ± 0.001% in ultrapure water and 98 ± 0.025% in marine water for 1 mg/L AgNPs. This method enables simple volume adjustment and improves the consistency of AgNP distribution on the membrane. The performance of the method was evaluated in different environmental waters, including marine water, fresh waters (pond water, river water, and reservoir outlet water) and drinking waters (municipal tap water and well water), with highest signal intensity in marine water and lowest signals in fresh waters. The signal intensity difference was suggested to be caused by the amount of natural organic matter (NOM) in these environmental waters. Using pond water as an example, the interference was minimized by changing the aggregating salt from AlCl₃ to MgCl₂, and AgNPs as low as 5 μg/L were reliably detected with a volume of 100 mL. At the same volume, the developed method was sensitive enough to detect 1 μg/L AgNPs in marine water and also holds promise for assessing the time-dependent transformation of AgNPs.

Biosynthesized Silver Nanoparticle (AgNP) From Pandanus odorifer Leaf Extract Exhibits Anti-metastasis and Anti-biofilm Potentials

Cancer and the associated secondary bacterial infections are leading cause of mortality, due to the paucity of effective drugs. Here, we have synthesized silver nanoparticles (AgNPs) from organic resource and confirmed their anti-cancer and anti-microbial potentials. Microwave irradiation method was employed to synthesize AgNPs using Pandanus odorifer leaf extract. Anti-cancer potential of AgNPs was evaluated by scratch assay on the monolayer of rat basophilic leukemia (RBL) cells, indicating that the synthesized AgNPs inhibit the migration of RBL cells. The synthesized AgNPs showed MIC value of 4-16 μg/mL against both Gram +ve and Gram -ve bacterial strains, exhibiting the anti-microbial potential. Biofilm inhibition was recorded at sub-MIC values against Gram +ve and Gram -ve bacterial strains. Violacein and alginate productions were reduced by 89.6 and 75.6%, respectively at 4 and 8 μg/mL of AgNPs, suggesting anti-quorum sensing activity. Exopolysaccharide production was decreased by 61-79 and 84% for Gram -ve and Gram +ve pathogens respectively. Flagellar driven swarming mobility was also reduced significantly. Furthermore, In vivo study confirmed their tolerability in mice, indicating their clinical perspective. Collective, we claim that the synthesized AgNPs have anti-metastasis as well as anti-microbial activities. Hence, this can be further tested for therapeutic options to treat cancer and secondary bacterial infections.

Surface-enhanced Raman spectroscopy of microorganisms: limitations and applicability on the single-cell level

Detection and characterization of microorganisms is essential for both clinical diagnostics and environmental studies. An emerging technique to analyse microbes at single-cell resolution is surface-enhanced Raman spectroscopy (surface-enhanced Raman scattering: SERS). Optimised SERS procedures enable fast analytical read-outs with specific molecular information, providing insight into the chemical composition of microbiological samples. Knowledge about the origin of microbial SERS signals and parameter(s) affecting their occurrence, intensity and/or reproducibility is crucial for reliable SERS-based analyses. In this work, we explore the feasibility and limitations of the SERS approach for characterizing microbial cells and investigate the applicability of SERS for single-cell sorting as well as for three-dimensional visualization of microbial communities. Analyses of six different microbial species (an archaeon, two Gram-positive bacteria, three Gram-negative bacteria) showed that for several of these organisms distinct features in their SERS spectra were lacking. As additional confounding factor, the physiological conditions of the cells (as influenced by e.g., storage conditions or deuterium-labelling) were systematically addressed, for which we conclude that the respective SERS signal at the single-cell level is strongly influenced by the metabolic activity of the analysed cells. While this finding complicates the interpretation of SERS data, it may on the other hand enable probing of the metabolic state of individual cells within microbial populations of interest.

Plasmonic Sensor Based on Interaction between Silver Nanoparticles and Ni2+ or Co2+ in Water

Silver nanoparticles capped with 3-mercapto-1propanesulfonic acid sodium salt (AgNPs-3MPS), able to interact with Ni²⁺ or Co²⁺, have been prepared to detect these heavy metal ions in water. This system works as an optical sensor and it is based on the change of the intensity and shape of optical absorption peak due to the surface plasmon resonance (SPR) when the AgNPs-3MPS are in presence of metals ions in a water solution. We obtain a specific sensitivity to Ni²⁺ and Co²⁺ up to 500 ppb (part per billion). For a concentration of 1 ppm (part per million), the change in the optical absorption is strong enough to produce a colorimetric effect on the solution, easily visible with the naked eye. In addition to the UV-VIS characterizations, morphological and dimensional studies were carried out by transmission electron microscopy (TEM). Moreover, the systems were investigated by means of dynamic light scattering (DLS), Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and high-resolution X-ray photoelectron spectroscopy (HR-XPS). On the basis of the results, the mechanism responsible for the AgNPs-3MPS interaction with Ni²⁺ and Co²⁺ (in the range of 0.5⁻2.0 ppm) looks like based on the coordination compounds formation.

Analytical Nanoscience and Nanotechnology: Where we are and where we are heading

The main aim of this paper is to offer an objective and critical overview of the situation and trends in Analytical Nanoscience and Nanotechnology (AN&N), which is an important break point in the evolution of Analytical Chemistry in the XXI century as they were computers and instruments in the second half of XX century. The first part of this overview is devoted to provide a general approach to AN&N by describing the state of the art of this recent topic, being the importance of it also emphasized. Secondly, particular but very relevant trends in this topic are outlined: the analysis of the nanoworld, the so "third way" in AN&N, the growing importance of bioanalysis, the evaluation of both nanosensors and nanosorbents, the impact of AN&N in bioimaging and in nanotoxicological studies, as well as the crucial importance of reliability of the nanotechnological processes and results for solving real analytical problems in the frame of Social Responsibility (SR) of science and technology. Several reflections are included at the end of this overview written as a bird's eye view, which is not an easy task for experts in AN&N.

Quantitative Proteomics Reveals Ecophysiological Effects of Light and Silver Stress on the Mixotrophic Protist Poterioochromonas malhamensis

Aquatic environments are heavily impacted by human activities including climate warming and the introduction of xenobiotics. Due to the application of silver nanoparticles as bactericidal agent the introduction of silver into the environment strongly has increased during the past years. Silver ions affect the primary metabolism of algae, in particular photosynthesis. Mixotrophic algae are an interesting test case as they do not exclusively rely on photosynthesis which may attenuate the harmful effect of silver. In order to study the effect of silver ions on mixotrophs, cultures of the chrysophyte Poterioochromonas malhamensis were treated in a replicate design in light and darkness with silver nitrate at a sub-lethal concentration. At five time points samples were taken for the identification and quantitation of proteins by mass spectrometry. In our analysis, relative quantitative protein mass spectrometry has shown to be a useful tool for functional analyses in conjunction with transcriptome reference sequences. A total of 3,952 proteins in 63 samples were identified and quantified, mapping to 4,829 transcripts of the sequenced and assembled transcriptome. Among them, 720 and 104 proteins performing various cellular functions were differentially expressed after eight days in light versus darkness and after three days of silver treatment, respectively. Specifically pathways of the energy and primary carbon metabolism were differentially affected by light and the utilization of expensive reactions hints to an energy surplus of P. malhamensis under light conditions. The excess energy is not invested in growth, but in the synthesis of storage metabolites. The effects of silver were less explicit, observable especially in the dark treatments where the light effect could not mask coinciding but weaker effects of silver. Photosynthesis, particularly the light harvesting complexes, and several sulphur containing enzymes were affected presumably due to a direct interference with the silver ions, mainly affecting energy supply.

Ultra-sensitive determination of silver nanoparticles by surface-enhanced Raman spectroscopy (SERS) after hydrophobization-mediated extraction

An innovative and ultra-sensitive SERS method that uses a triple-functional surfactant ligand for nanoparticle surface binding, phase transfer and SERS signal reporting was developed for silver nanoparticle (AgNP) detection.