Use of (modified) natural adsorbents for arsenic remediation: A review

Arsenic and antimony desorption in water treatment processes: Scaling up challenges with emerging adsorbents

The metalloids arsenic (As) and antimony (Sb) belong to the pnictogen group of the periodic table; they share many characteristics, including their toxic and carcinogenic properties; and rank as high-priority pollutants in the United States and the European Union. Adsorption is one of the most effective techniques for removing both elements and desorption, for further reuse, is a part of the process to make adsorption more sustainable and feasible. This review presents the current state of knowledge on arsenic and antimony desorption from exhausted adsorbents previously used in water treatment, that has been reported in the literature. The application of different types of eluents to desorb As and Sb and their desorption performance are described. The regeneration of saturated adsorbents and adsorbate recovery techniques are outlined, including the fate of spent media and possible alternatives for waste disposal of exhausted materials. Future research directions are discussed, as well as current issues including the lack of environmental impact analysis of emerging adsorbents.

Gestational α-ketoglutarate supplementation ameliorates arsenic-induced hepatic lipid deposition via epigenetic reprogramming of β-oxidation process in female offspring

Inorganic trivalent arsenic (iAsⅢ) at environmentally relevant levels has been found to cause developmental toxicity. Maternal exposure to iAsⅢ leads to enduring hepatic lipid deposition in later adult life. However, the exact mechanism in iAsⅢ induced hepatic developmental hazards is still unclear. In this study, we initially found that gestational exposure to iAsⅢ at an environmentally relevant concentration disturbs lipid metabolism and reduces levels of alpha-ketoglutaric acid (α-KG), an important mitochondrial metabolite during the citric acid cycle, in fetal livers. Further, gestational supplementation of α-KG alleviated hepatic lipid deposition caused by early-life exposure to iAsⅢ. This beneficial effect was particularly pronounced in female offspring. α-KG partially restored the β-oxidation process in hepatic tissues by hydroxymethylation modifications of carnitine palmitoyltransferase 1a (Cpt1a) gene during fetal development. Insufficient β-oxidation capacities probably play a crucial role in hepatic lipid deposition in adulthood following in utero arsenite exposure, which can be efficiently counterbalanced by replenishing α-KG. These results suggest that gestational administration of α-KG can ameliorate hepatic lipid deposition caused by iAsⅢ in female adult offspring partially through epigenetic reprogramming of the β-oxidation pathway. Furthermore, α-KG shows potential as an interventive target to mitigate the harmful effects of arsenic-induced hepatic developmental toxicity.

How Fe-bearing materials affect soil arsenic bioavailability to rice: A meta-analysis

Arsenic (As) contamination is widespread in soil and poses a threat to agricultural products and human health due to its high susceptibility to absorption by rice. Fe-bearing materials (Fe-Mat) display significant potential for reducing As bioavailability in soil and bioaccumulation in rice. However, the remediation effect of various Fe-Mat is often inconsistent, and the response to diverse environmental factors is ambiguous. Here, we conducted a meta-analysis to quantitatively assess the effects of As in soils, rice roots, and grains based on 673, 321, and 305 individual observations from 67 peer-reviewed articles, respectively. On average, Fe-Mat reduced As bioavailability in soils, rice roots, and grains by 28.74 %, 33.48 %, and 44.61 %, respectively. According to the analysis of influencing factors, the remediation efficiency of Fe-Mat on As-contaminated soil was significantly enhanced with increasing Fe content in the material, in which the industry byproduct was the most effective in soils (-42.31 %) and rice roots (-44.57 %), while Fe-biochar was superior in rice grains (-54.62 %). The efficiency of Fe-Mat in minimizing soil As mobility was negatively correlated with soil Fe content, CEC, and pH. In addition, applying Fe-Mat in alkaline soils with higher silt, lower clay and available P was more effective in reducing As in rice grains. A higher efficiency of applying Fe-Mat under continuous flooding conditions (27.39 %) compared with alternate wetting and drying conditions (23.66 %) was also identified. Our results offer an important reference for the development of remediation strategies and methods for various As-contaminated paddy soils.

The potential of zeolite nanocomposites in removing microplastics, ammonia, and trace metals from wastewater and their role in phytoremediation

Nanocomposites are emerging as a new generation of materials that can be used to combat water pollution. Zeolite-based nanocomposites consisting of combinations of metals, metal oxides, carbon materials, and polymers are particularly effective for separating and adsorbing multiple contaminants from water. This review presents the potential of zeolite-based nanocomposites for eliminating a range of toxic organic and inorganic substances, dyes, heavy metals, microplastics, and ammonia from water. The review emphasizes that nanocomposites offer enhanced mechanical, catalytic, adsorptive, and porosity properties necessary for sustainable water purification techniques compared to individual composite materials. The adsorption potential of several zeolite-metal/metal oxide/polymer-based composites for heavy metals, anionic/cationic dyes, microplastics, ammonia, and other organic contaminants ranges between approximately 81 and over 99%. However, zeolite substrates or zeolite-amended soil have limited benefits for hyperaccumulators, which have been utilized for phytoremediation. Further research is needed to evaluate the potential of zeolite-based composites for phytoremediation. Additionally, the development of nanocomposites with enhanced adsorption capacity would be necessary for more effective removal of pollutants.

Facile preparation of maghemite based on iron sludge for arsenic removal from water

In this study, we demonstrated the effective acquisition of magnetic iron oxide (MIO) for As(V) adsorption by high-temperature pyrolysis of waste iron sludge from the water treatment plant under a confined environment without adding extra chemical reagents. The operating temperature and time in the pyrolysis process were optimized to improve the yield of MIO and its As(V) adsorption capacity. MIO500-2(500 °C, 2 h) had both relatively high yield and arsenic adsorption efficiency, which was characterized by XRD and XPS as mainly γ-Fe2O3 with small particle size (100-900 nm), significant mesopore (12.43 nm), high specific surface area (65.25 m2/g), and effective saturation magnetization intensity (14.45 emu/g). The maximum adsorption capacity was 14.2 ± 0.4 mg/g, and the removal rate could still reach about 80 % after five times of adsorbent regeneration. Considering this facile preparation route and its high yield, large-scale production of MIO from waste iron sludge is feasible, which is expected to provide a low-cost and efficient adsorbent for the treatment of arsenic-containing water in less economically developed areas.

Capture gaseous arsenic in flue gas by amorphous iron manganese oxides with high SO2 resistance

In non-ferrous metal smelting, the problem of gaseous arsenic in high-sulfur flue gas is difficult to solve. Now we have developed oxygen-enriched amorphous iron manganese oxide (AFMBO) based on the unique superiority of iron-manganese oxide for arsenic capture to realize the effective control of gaseous arsenic in the non-ferrous smelting flue gas. The experimental results show that the arsenic adsorption capacity of AFMBO is up to 102.7 mg/g, which has surpassed most of the current adsorbents. In particular, AFMBO can effectively capture gaseous arsenic even at 12% v/v SO2 concentrations (88.45 mg/g). Moreover, the spent AFMBO possesses pronounced magnetic characteristics that make it easier to separate from dust, which is conducive to reducing the secondary environmental risk of arsenic. In terms of mechanism study, various characterization methods are used to explain the important role of lattice oxygen and adsorbed oxygen in the capture process of gaseous arsenic. Moreover, the reason for the efficient arsenic removal performance of AFMBO is also reasonably explained at the microscopic level. This study provides ideas and implications for gaseous arsenic pollution control research.

Effects of Fe(II) concentration on the biosynthesis of schwertmannite by Acidithiobacillus ferrooxidans and the As(III) removal capacity of schwertmannite

The effect of Fe(II) concentrations on schwertmannite bio-synthesis and the As(III) removal capacity of schwertmannite were investigated in this study. Acidithiobalillus ferrooxidans (A. ferrooxidans) were inoculated into five FeSO4 systems with initial concentrations of 50, 100, 200, 300, and 400 mmol/L, respectively, to bio-synthesize schwertmannite. The Fe(II) of the systems were almost completely oxidised at 48, 72, 120, 168, and 192 h, respectively, and the bio-schwertmannite yield was 1.99, 3.81, 9.36, 12.42, and 21.60 g/L. The results of this study indicate that all minerals harvested from the different systems are schwertmannite. As the initial Fe(II) concentration increases, the effect of the minerals removing As(III) decreases; moreover, the structure and extracellular polymeric substance (EPS) of schwertmannite may regulate the As(III) removal process. The EPS generated by the A. ferrooxidans can absorb As(III). The outcomes of this study provide fresh insights into the bio-synthetic regulation of schwertmannite and play a significant role in treating As-containing groundwater.

The effectiveness of sewage sludge biochar amendment with Boehmeria nivea L. in improving physicochemical properties and rehabilitating microbial communities in mine tailings

Biochar amendment can be adopted to improve soil substrate, in turn facilitated phytoremediation. However, improvements to the properties of tailings following different feedstocks of biochar amendment in phytoremediation, particularly the impacts on nitrogen cycle and the related nitrogen-fixing microorganisms remain unclear. In this study, a 100-day pot experiment was designed to determine the co-effects of different combinations of woody and non-woody biochar, namely hibiscus cannabinus core biochar (HB), sewage sludge biochar (SB), chicken manure biochar (MB) and two crops (Cassia alata L., Boehmeria nivea L.). It was found that, on the one hand, biochar amendment directly immobilized heavy metal (loid) contamination in the tailings; on the other hand, biochar amendment, particularly non-woody SB, improved soil properties (i.e., the combination of SB with crops increased the total nitrogen content by 4.7-7.5 times). This indirectly improved phytostabilization (i.e., SB increased crop height 1.5-1.8 fold, root length 3.3-3.7 fold, decreased NH4NO3-extractable Pb, Cu, Cd and also increased the relative abundance of nitrogen-fixing bacteria such as Mesorhizobium, Bradyrhizobium, and Rhizobium). Besides this, redundant analysis shown that the carbon, nitrogen sources, and pH provided by the biochar were identified as the key factors associated with the nitrogen-fixing bacteria. Through the comprehensive evaluation of different biochar amendment in phytoremediation, it was found that the non-woody SB got higher comprehensive score (3.1-3.6) in biochar amendment in phytoremediation, especially in Boehmeria nivea L. Thus, the combination of non-woody SB and Boehmeria nivea L. improved microbial function, while the microorganisms in turn promoted crop growth. Our results revealed the prospect of using non-woody SB assisted Boehmeria nivea L. for phytoremediation in multi-metal mine tailings.

Preparation of basic magnesium carbonate nanosheets modified pumice and its adsorption of heavy metals

Heavy metal pollution in wastewater poses a grave danger to the environment and the human body. Pumice is a mineral with abundant reserves and low prices, and its prospect of heavy metal adsorbent is very broad. In this work, we modified pumice with basic magnesium carbonate nanosheets by a convenient hydrothermal synthesis. The adsorption capacity of heavy metals is greatly improved. The effects of different pH and adsorption dosages are investigated. All the optimum pH values for Cu2+, Pb2+, and Cd2+ are 5. The adsorption of three kinds of ions conforms to the quasi-second-order adsorption kinetics model. The theoretical adsorption capacities of Cu2+, Pb2+, and Cd2+, which are calculated by the Langmuir model, are 235.29 mg/L, 595.24 mg/L, and 370.34 mg/L, respectively. The adsorption of Cu2+ and Cd2+ fit the Langmuir model better. The Freundlich model is fitted well with the adsorption of Pb2+. In the experiment simulating real wastewater, the adsorption capacity of heavy metals is not affected. It also shows good reusability in three regeneration cycles. And Mg5(CO3)4(OH)2·4H2O@pumice adsorption column showed the good removal efficiency of three heavy metals at different concentrations and different spatial velocities in the column experiment. Thus, it is believed that the Mg5(CO3)4(OH)2·4H2O@pumice is a promising adsorbent for the efficient removal of heavy metals.

A comprehensive review of coconut-based porous materials for wastewater treatment and CO2 capture

For several decades, water pollution has become a major threat to aquatic and non-aquatic species, including humans. Different treatment techniques have already been proposed and implemented depending on wastewater characteristics. But many of these treatment techniques are expensive and inefficient. Adsorption-based techniques have shown impressive performances as an inexpensive treatment method previously. Coconut-based resources have been considered as adsorbents for wastewater treatment because of their abundance, low cost, and favorable surface properties. However, over the last decade, no comprehensive study has been published regarding biochar from coconut-based materials for wastewater treatment and CO2 capture. This review discusses biochar production technology for coconut-based materials, its modification and characterization, its utilization as an adsorbent for removing metals and organics from wastewater, and the associated removal mechanisms and the economic aspects of coconut-based biochar. Coconut-based materials are cheap and effective for removing various organic compounds such as pesticides, hormones, phenol, and phenolic compounds from solutions and capturing CO2 from air mainly through the pore-filling mechanism. Utilizing coconut-based biochars in a hybrid system that combines adsorption and other techniques, such as biotechnology or chemical coagulation is a promising way to increase their performance as an adsorbent in wastewater treatment.

Adsorption of heavy metals on natural zeolites: A review

Water pollution has jeopardized human health, and a safe supply of drinking water has been recognized as a worldwide issue. The increase in the accumulation of heavy metals in water from different sources has led to the search for efficient and environmentally friendly treatment methods and materials for their removal. Natural zeolites are promising materials for removing heavy metals from different sources contaminating the water. It is important to know the structure, chemistry, and performance of the removal of heavy metals from water, of the natural zeolites to design water treatment processes. This review focuses on critical analyses of the application of distinct natural zeolites for the adsorption of heavy metals from water, specifically, arsenic (As(III), As(V)), cadmium (Cd(II)), chromium (Cr(III), Cr(VI)), lead (Pb(II)), mercury(Hg(II)) and nickel (Ni(II)). The reported results of heavy-metal removal by natural zeolites are summarized, and the chemical modification of natural zeolites by acid/base/salt reagent, surfactants, and metallic reagents has been analyzed, compared, and described. Furthermore, the adsorption/desorption capacity, systems, operating parameters, isotherms, and kinetics for natural zeolites were described and compared. According to the analysis, clinoptilolite is the most applied natural zeolite to remove heavy metals. It is effective in removing As, Cd, Cr, Pb, Hg, and Ni. Additionally, an interesting fact is a variation between the natural zeolites from different geological origins regarding the sorption properties and capacities for heavy metals suggesting that natural zeolites from different regions of the world are unique.

A mini-review on arsenic remediation techniques from water and future trends

Arsenic contamination is a severe issue because of its toxicity and related health risks. This review article presents an overview of the sources, health hazards, and treatment options for arsenic pollution. Conventional approaches to achieving the permitted level of 10 ppb set by the WHO, such as chemical oxidation, biological oxidation, and coagulation-flocculation, are ineffective and time-consuming. The paper analyses the advantages and disadvantages of various advanced treatment technologies, including membrane filtration, ion exchange, advanced oxidation, phytoremediation, and adsorption. This paper summarized the effectiveness of hybrid arsenic remediation techniques in removing arsenic and its operating conditions. This study is a helpful tool for putting remediation strategies into practice. This article describes arsenic pollution's damaging effects on human health, underscoring the necessity for careful treatment. The article addresses numerous treatment technologies, each with advantages and disadvantages preventing widespread use. Due to these limitations, deciding the best technique for arsenic remediation is difficult. As a result, hybrid treatment systems are urgently needed, with photocatalysis-adsorption being the most popular approach. The relevance of adaptable, user-friendly, low-maintenance hybrid technologies that are versatile, easy to use, and provide affordable arsenic removal options, especially for poor populations, is highlighted by prospects.

Biochar modification to enhance arsenic removal from water: a review

Arsenic (As) contamination is a major threat to drinking water quality throughout the world, and the development of appropriate remediation methods is critical. Adsorption is considered the most effective method for remediation of As-contaminated water. Biochar is a promising adsorbent and widely discussed for As removal due to its potential low cost and environmental friendliness. However, pristine biochar generally exhibited relatively low adsorption capacity for As mainly due to the electrostatic repulsion between the negatively charged biochar and As. Biochar modification, especially metal modification, was developed to boost the adsorption capacity for As. A systematic analysis of As removal as affected by biochar properties and modification will be of great help for As removal. This paper presents a comprehensive review on As removal by biochars from different feedstock, preparation procedures, and modification methods, with a major focus on the possible mechanisms of interaction between As and biochar. Biochar derived from sewage sludge exhibited relatively high adsorption capacity for As. Considering energy conservation, biochars prepared at 401-500 °C were more favorable in adsorbing As. Fe-modified biochar was the most popular modified biochar for As remediation due to its low cost and high efficiency. In addition, the limitations of the current studies and future perspectives are presented. The aim of this review is to provide guidance for the preparation of low-cost, environmentally friendly, and high efficiency biochar for the remediation of As-contaminated water.

Valorization of Fibrous Plant-Based Food Waste as Biosorbents for Remediation of Heavy Metals from Wastewater-A Review

Mobilization of heavy metals in the environment has been a matter of concern for several decades due to their toxicity for humans, environments, and other living organisms. In recent years, use of inexpensive and abundantly available biosorbents generated from fibrous plant-based food-waste materials to remove heavy metals has garnered considerable research attention. The aim of this review is to investigate the applicability of using fibrous plant-based food waste, which comprises different components such as pectin, hemicellulose, cellulose, and lignin, to remove heavy metals from wastewater. This contribution confirms that plant-fiber-based food waste has the potential to bind heavy metals from wastewater and aqueous solutions. The binding capacities of these biosorbents vary depending on the source, chemical structure, type of metal, modification technology applied, and process conditions used to improve functionalities. This review concludes with a discussion of arguments and prospects, as well as future research directions, to support valorization of fibrous plant-based food waste as an efficient and promising strategy for water purification.

A review on arsenic in the environment: bio-accumulation, remediation, and disposal

Arsenic is a widespread serious environmental pollutant as a food chain contaminant and non-threshold carcinogen. Arsenic transfer through the crops-soil-water system and animals is one of the most important pathways of human exposure and a measure of phytoremediation. Exposure occurs primarily from the consumption of contaminated water and foods. Various chemical technologies are utilized for As removal from contaminated water and soil, but they are very costly and difficult for large-scale cleaning of water and soil. In contrast, phytoremediation utilizes green plants to remove As from a contaminated environment. A large number of terrestrial and aquatic weed flora have been identified so far for their hyper metal removal capacity. In the panorama presented herein, the latest state of the art on methods of bioaccumulation, transfer mechanism of As through plants and animals, and remediation that encompass the use of physicochemical and biological processes, i.e., microbes, mosses, lichens, ferns, algae, and macrophytes have been assessed. Since these bioremediation approaches for the clean-up of this contaminant are still at the initial experimental stages, some have not been recognized at full scale. Nonetheless, extensive research on these primitive plants as bio-accumulators can be instrumental in controlling arsenic exposure and rehabilitation and may result in major progress to solve the problem on a worldwide scale.

Magnetite interaction with arsenic during sorptive removal from groundwater: a mechanistic study

A magnetic mixed iron oxide, magnetite (Fe₃O₄), was synthesized in the laboratory and characterized before its use as sorbent for arsenic removal. The characterization techniques used were X-ray diffraction (XRD), specific surface area, zeta potential and particle size measurements. The sorbent was applied for arsenic removal, without any pre or post treatment, from groundwater. The efficiency of sorption can only be improved by understanding the sorbent-sorbate interaction. For onsite monitoring of the sorbent-sorbate interaction, an electrochemical investigation using cyclic voltammetry (CV) measurement was developed. The study confirmed that the sorption of As(III) on Fe₃O₄ is dynamic (reversible) whereas that of As(V) is static (irreversible) in nature. Detailed investigation after the sorption was carried out utilizing X-ray photoelectron spectroscopy (XPS) measurement. The complexation of As(III)-Fe₃O₄ and As(V)-Fe₃O₄ without any redox transformation was evident from the XPS data. By careful examination of the results, a mechanism of arsenic removal by Fe₃O₄ was proposed.

Comparative study for sorption of arsenic on peanut shell biochar and modified peanut shell biochar

In this study, arsenite [As(III)] and arsenate [As(V)] removal efficiency of peanut shell biochar (PSB) and modified peanut shell biochar (MPSB) was compared in aqueous solutions. The modification was carried out with KMnO₄ and KOH. Sorption efficiency of MPSB was relatively higher than PSB at pH 6 for As(III) (86%) and for As(V) (91.26%) for initial concentration of 1 mg/L, adsorbent dose of 0.5 g/L and 240 min equilibrium time at 100 rpm. Freundlich isotherm and pseudo-second order kinetic model suggested possible multilayer chemisorption. Fourier transform infrared spectroscopy showed that -OH, C-C, CC and C-O-C groups contributed significantly in adsorption for both PSB and MPSB. Thermodynamic study showed that the adsorption process was spontaneous and endothermic. Regeneration studies revealed that PSB and MPSB can be successfully used for three cycles. This study established that peanut shell is a low-cost, environment friendly and efficient biochar for removal of arsenic from water.

FeSx@MOF-808 composite for efficient As(III) removal from wastewater: behavior and mechanism

Arsenic is extremely toxic to humans with water as its carrier. One challenge for arsenic control is the complete elimination of As(III) due to its high toxicity, mobility, and solubility. Herein, an active FeS_x@MOF-808 composite was fabricated to enhance the As(III) removal for wastewater remediation. The FeS_x@MOF-808 showed better As(III) adsorptive performance (Q_e = 73.60 mg/g) compared with Fe₂S₃ (Q_e=12.38 mg/g), MOF-808 (Q_e = 27.85 mg/g), and Fe@MOF-808 (Q_e=34.26 mg/g). This can be attributed to an improved porous structure provided by MOF-808 and abundant reactive sites provided by FeS_x. Calculated by the Langmuir model (R² =0.9965), the maximum adsorption capacity (Q_max) of FeS_x@MOF-808 for As(III) removal at 298 K and pH = 7 was 203.28 ± 6.43 mg/g, which is beyond most of the traditional materials and MOFs. Additionally, FeS_x@MOF-808 exhibited good stability in a wide pH range (1-13). Results also showed that the different Fe/S ratios (1:0-1:8) and FeS_x loading amount (0.00625-0.25 mmol) have effects on the FeS_x@MOF-808 performance. By kinetics studies, XPS, and DFT calculation, the mechanisms for arsenic by FeS_x@MOF-808 were proposed. Multiple reaction mechanisms combine the adsorption by the MOF-808 support, the co-precipitation of iron oxides via hydroxyl (Fe-OH) groups, and most importantly, the precipitation through the break of Fe-S and the bond of As-S.

Waste bamboo framework decorated with α-FeOOH nanoneedles for effective arsenic (V/III) removal

Arsenic pollution of water is one of the severest environmental challenges for human health, and adsorption is the most often used technique in investigations of selective As removal. However, the development of low-cost and easily recoverable adsorbent for aqueous arsenic adsorption remains a challenge. In this work, the α-FeOOH-decorated monolith bamboo composites (α-FeOOH/MB) were fabricated via directly decorating α-FeOOH nanoneedles on the waste bamboo framework without pre‑carbonization. As expected, the as-prepared α-FeOOH/MB exhibits considerably increased adsorption capacity for aqueous arsenic over pure α-FeOOH nanoneedles, with increases of 1.88 and 1.52 times for As(V) and As(III), respectively. Meanwhile, the α-FeOOH/MB composites exhibit positive reusability (recovering 89.73 % and 80.17 % adsorption capacity for As(V) and As(III) after 5 cycles) and are easy to separate after water treatment. Furthermore, the α-FeOOH/MB composites exhibit high arsenic adsorption selectivity even in the presence of competing anions. Overall, the as-obtained α-FeOOH/MB composites, reuse of waste bamboo, are a kind of favorable candidate for arsenic decontamination in practical application owing to the high adsorption capacity, low-cost and facile separation features.

Recyclable Magnetic Iron Immobilized onto Chitosan with Bridging Cu Ion for the Enhanced Adsorption of Methyl Orange

Chitosan (CS) is a natural and low-cost adsorbent for capturing metal ions and organic compounds. However, the high solubility of CS in acidic solution would make it difficult to recycle the adsorbent from the liquid phase. In this study, the CS/Fe₃O₄ was prepared via Fe₃O₄ nanoparticles immobilized onto a CS surface, and the DCS/Fe₃O₄-Cu was further fabricated after surface modification and the adsorption of Cu ions. The meticulously tailored material displayed the sub-micron size of an agglomerated structure with numerous magnetic Fe₃O₄ nanoparticles. During the adsorption of methyl orange (MO), the DCS/Fe₃O₄-Cu delivered a superior removal efficiency of 96.4% at 40 min, which is more than twice the removal efficiency of 38.7% for pristine CS/Fe₃O₄. At an initial MO concentration of 100 mg L^-1, the DCS/Fe₃O₄-Cu exhibited the maximum adsorption capacity of 144.60 mg g^-1. The experimental data were well explained by the pseudo-second-order model and Langmuir isotherm, suggesting the dominant monolayer adsorption. The composite adsorbent still maintained a large removal rate of 93.5% after five regeneration cycles. This work develops an effective strategy to simultaneously achieve high adsorption performance and convenient recyclability for wastewater treatment.

Arsenic removal from aqueous solution: A comprehensive synthesis with meta-data

Removal of arsenic from drinking water is one of the most important global concerns. Among the various techniques, adsorptive removal of arsenic is considered as a viable most effective method. However, limited attention is given to understand the overall relative sorption capacity of different sorbents (e.g., biocomposite, biochar and nano-composite etc.) since various factors influence the sorption capacity. The aim of this study is to assess the effectiveness of various adsorbents with quantitative estimation (Langmuir adsorption maxima, Qmax) as well as to evaluate the influence of experimental conditions on the achievement of maximum adsorption. A number of analyses including meta-analysis, analysis of variance (ANOVA), scientometric and regression were performed. The results revealed that among the sorbents, nanoparticles show the greatest sorption capacity while pre-doped biochar performed the best among different biochars. Average across all sorbents, As (V) removal efficacy was higher than As (III). As expected, a high point of zero charge (PZC) and higher positive surface charge favored adsorption. The relative contribution of different mechanisms was also discussed. Our scientometric analyses revealed that, research should focus on the development of low-cost adsorbents and increase their reusability, safe disposal of adsorbed arsenic. Altogether, our findings provide a molecular understanding of arsenic sorption to different sorbents with implications for tailoring a good sorbent for arsenic removal from drinking water.

Efficient separation of arsenic species of oxyanion As (III) and As (V) by using effective polymer inclusion membranes (PIM)

The heavy metal contaminant arsenic exist in the form of arsenite (As(III)) and arsenate (As(V)) ions. These ions are highly carcinogenic that are usually present in the ground water. To date, most of the designed polymer inclusion membrane (PIM) involved only about separation without differentiating the oxidation states. Thus, there is a research gap on separation of element with different oxidation states. Thus, this study addresses such research gap which have been not explored previously. To extract such ions from water, the present study involves fabrication of PIM by varying the compositions of the base polymer, carrier and plasticizer. Also effect of the strip solution, and transport properties were studied. High performance membrane was obtained with 50% (w/w) Aliquat 336 and 50% (w/w) Cellulose triacetate (CTA). The production of 1 m² of PIM may cost approximately 0.08-0.16$. Also, we have combined the separation capacity of polymer inclusion membrane (PIM) with the sensitivity and elemental detection using atomic absorption spectrometry (AAS) to detect and separate As(III) and As(V). AAS is limited to detecting only elemental arsenic (As) and does not distinguish between As(III) and As(V). Further, to address such limitations in this current study we were able to separate As(V) from As(III) within 5 h. In addition, to provide sole solution a device was fabricated to extract As(V) in the field studies which displayed outstanding efficiency of 99.7 ± 0.2%. The extracted samples was tested in AAS to differentiate between oxidation states of the arsenic species and these important results are supportive in finding out the redox potential of water and for other geochemical explorations.

Remediation of Acid Mine Drainage (AMD) Using Steel Slag: Mechanism of the Alkalinity Decayed Process

Steel slag has been proven to be an effective environment remediation media for acid neutralization, and a potential aid to mitigate acid mine drainage (AMD). Yet its acid neutralization capacity (ANC) is frequently inhibited by precipitate after a period of time, while the characteristics of the precipitate formation process are unclear yet. In this study, ANC for basic oxygen steel slag was conducted by neutralization experiments with dilute sulfuric acid (0.1 M) and real AMD. Some partially neutralized steel slag samples were determined by X-ray diffraction (XRD), scanning electron microscopy combined with an energy dispersive spectrometer (SEM-EDS), and N2 adsorption tests to investigate the potential formation process of the precipitate. The results indicated that Ca-bearing constitutes leaching and sulfate formation were two main reactions throughout the neutralization process. A prominent transition turning point from leaching to precipitate was at about 40% of the neutralization process. Tricalcium silicate (Ca3SiO5) played a dominant role in the alkalinity-releasing stage among Ca-bearing components, while the new-formed well crystalline CaSO4 changed the microstructure of steel slag and further hindered alkaline components releasing. For steel slag of 200 mesh size, the ANC value for the steel slag sample was 8.23 mmol H+/g when dilute sulfate acid was used. Neutralization experiments conducted by real AMD confirmed that the steel slag ANC was also influenced by the high contaminants, such as Fe2+, due to the hydroxides precipitate reactions except for sulfate formation reactions.

A data-driven modeling approach for the sustainable remediation of persistent arsenic (As) groundwater contamination in a fractured rock aquifer through a groundwater recirculation well (IEG-GCW®)

Persistent arsenic (As) pollution sources from anthropogenic activities pose a serious threat to groundwater quality. This work aims to illustrate the application of an innovative remediation technology to remove As from a heavily contaminated fractured aquifer at a historically polluted industrial site. Groundwater circulation well (GCW) technology was tested to significantly increase and accelerate the mobilization and removal of As in the source area. The GCW extracts and re-injects groundwater at different depths of a vertical circulation well. By pumping out and reinjecting in different screen sections of the well, the resulting vertical hydraulic gradients create recirculation cells and affect and mobilize trapped contaminants that cannot be influenced by traditional pumping systems. The first 45-m deep IEG-GCW® system was installed in 2020, equipped with 4 screen sections at different depths and with an above-ground As removal system by oxidation and filtration on Macrolite (Enki). A geomodeling approach supports both remediation and multi-source data interpretation. The first months of operation demonstrate the hydraulic effectiveness of the IEG-GCW® system in the fractured rock aquifer and the ability to significantly enhance As removal compared to conventional pumping wells currently feeding a centralized treatment system. The recirculation flow rate amounts to about 2 m³/h. Water pumped and treated by the GCW system is reintroduced with As concentrations reduced by an average of 20%-60%. During the pilot test, the recirculating system removed 23 kg As whilst the entire central pump-and-treat (P&T) system removed 129 kg, although it treated 100 times more water volume. The P&T plant removed 259 mg As per m³ of pumped and treated groundwater while the GCW removed 4814 mg As per m³ of the treated groundwater. The results offer the opportunity for a more environmentally sustainable remediation approach by actively attacking the contamination source rather than containing the plume.

Adsorption and desorption characteristics of arsenic in calcareous soils as a function of time; equilibrium and thermodynamic study

Irrigation of carbonate-rich agricultural soils with arsenic (As)-contaminated water leads to the accumulation of As in these soils. In this regard, there is an opportunity to adsorb and fix the As in soil and decrease the As transportation to the plants and subsequently the human food chain. So, the present study aimed to investigate the adsorption-desorption characteristics of As in calcareous soils and the potential of As fixation over time. First, to achieve this purpose, 53 soil samples were gathered from the study site and after the laboratory analysis, the soils were categorized into four groups based on their physicochemical properties. Then, four representative samples of these groups were selected, namely soil 1, soil 2, soil 3, and soil 4. Afterward, the As adsorption-desorption was investigated in a lab-scale batch experiment. Next, the effect of age was assessed by incubating the As-adsorbed soils for 60 days, and to study the impact of temperature, the adsorption was performed at four temperature levels (10, 20, 30, and 40 °C). Finally, the isotherm models were fitted to experimental data, and the amount of loosely and tightly held As was quantified. Results revealed that the As adsorption isotherms were L-type, in which As adsorption increased with the increase of As loading. The double-site Langmuir (DSL) estimated that a limited amount of As was adsorbed on high-energy surfaces and a large amount of As was adsorbed on low-energy surfaces. Desorption results showed that a significant amount of As desorbed immediately; however, the desorption significantly decreased with the increase of age, especially at low equilibrium concentrations. By aging the loosely held As transformed into non-labile forms so that in soils 1, 2, 3, and 4, the fraction of As adsorbed on high-energy surfaces increased from 72.5, 93.2, 63.2, and 123 mg/kg to 167, 141, 70.6, and 196 mg/kg, respectively, and the fraction of As adsorbed on low-energy surfaces decreased from 397, 256, 202, and 317 mg/kg to 182, 238, 173, and 172 mg/kg, respectively (after aging for 60 days). Aging proved to be a promising solution for decreasing As transport into the human food chain and could be employed for crops with longer irrigation cycles. ΔH_ad values were positive and varied from 9.26 to 13.0 kJ/mol, confirming the endothermic nature of adsorption. ΔG_ad values were negative and varied from - 18.8 to - 22.8 kJ/mol at all temperatures, demonstrating the spontaneous nature of adsorption.

Modified biochar: synthesis and mechanism for removal of environmental heavy metals

With social progress and industrial development, heavy metal pollution in water and soils environment is becoming more serious. Although biochar is a low-cost and environmentally friendly adsorbent for heavy metal ions, its adsorption and immobilization efficiency still need to be improved. As an upgraded version of biochar, modified biochar has attracted extensive attention in the scientific community. This review summarized the recent research progress on the treatment methods on heavy metal pollutants in water and soils using biochar. The features and advantages of biochar modification techniques such as physical modification, chemical modification, biological modification and other categories of biochar were discussed. The mechanism of removing heavy metals from soil and water by modified biochar was summarized. It was found that biochar had better performance after modification, which provided higher surface areas and more functional groups, and had enough binding sites to combine heavy metal ions. Biochar is a very promising candidate for removing heavy metals in environment. Furthermore, some high valent metal ions could be reduced to low valent metals, such as Cr(VI) reduction to Cr(III), and form precipitates on biochar by in-situ sorption-reduction-precipitation strategy. However, it is still the direction of efforts to develop high-efficiency modified biochar with low-cost, high sorption capacity, high photocatalytic performance, environmentally friendly and no secondary pollution in future.

Preparation of Mannitol-Modified Loofah and Its High-Efficient Adsorption of Cu(II) Ions in Aqueous Solution

Adsorption is considered the most favorable method for heavy metal removal. In this paper, a low-cost, high-efficiency heavy metal adsorbent, mannitol-modified loofah (MML) was prepared. Some characterization methods are used to characterize the structure of MML, such as Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The adsorption behavior of MML for Cu(II) ions was explored under different conditions, such as the amount of adsorbent, pH, initial concentration of Cu(II) ions, and adsorption time. The results indicated that the adsorption capacity of MML for Cu(II) ions was greatly improved. When the initial concentration of Cu(II) ions was 900 mg/L and the pH is 5.0, the adsorption capacity (Q_e) was 888.9 mg/g at 298K, which was significantly higher than that of some other modified cellulose adsorbents. Isothermal adsorption results showed that the adsorption process was consistent with the Freundlich model. The adsorption kinetics conformed to the pseudo-second-order equation. Furthermore, the regeneration capability of MML indicates that MML is a cheap and excellent adsorbent for Cu(II) ions removal in wastewater treatment.

Jute Fibers Synergy with nZVI/GO: Superficial Properties Enhancement for Arsenic Removal in Water with Possible Application in Dynamic Flow Filtration Systems

Groundwater is one of the primary sources of water for both drinking and industrial use in northeastern Mexican territory, around 46% of the total, due to the lack of precipitation during the year and solar radiation index. The presence of arsenic in brackish soil and groundwater is a severe health issue, specifically in semi-arid and arid regions in the north of Mexico. Additionally, it represents the only source of drinking water in communities far from big cities, mainly due to the absence of hydric infrastructure. This work presents a new approach to treating polluted water with arsenic. The system based on activating jute fiber with nanoparticles of zero-valent iron immobilized over graphene oxide will allow nZVI particles to preserve their unique qualities for water sanitization. A dynamic flow test was designed to determine the effectivity of activated jute fibers as a water sanitation system. The results showed a reduction in the total arsenic content from 350 ppb to 34 ppb with a filtrate flow of 20 mL/min. The above represents 90% adsorption by the activated fiber. The analyzed sample corresponds to contaminated groundwater taken from Coahuila, Mexico. This sanitation system could be applied to low-income populations lacking robust infrastructure, such arsenic treatment plants.

Nanostructured electrochemical sensor applied to the electrocoagulation of arsenite in WWTP effluent

A sensitive electroanalytical method for the determination of arsenite, based on a heterostructure of aminated multiwalled carbon nanotubes and gold nanoparticles, was applied in an electrocoagulation (EC) treatment for the elimination of arsenite. A sensitive quantitative response was obtained in the determination of As³⁺ in a secondary effluent from a wastewater treatment plant from Santiago (Chile). The preconcentration stage was optimized through a Central Composite Face design, and the most sensitive peak current was obtained at 200 s and -600 mV of time and accumulation potential, respectively, after a differential pulse voltammetry sweep. Electroanalytical determination was possible in an interval between 42.89 and 170.00 μg L^-1 with a detection limit of 0.39 μg L^-1, obtaining recoveries over 99.1%. The developed method was successfully applied in an electrocoagulation treatment to remove 250 μg L^-1 of arsenite from a polluted effluent in a batch system. Complete arsenite removal was achieved using a steel EC system with a current density of 6.0 mA cm^-2 in less than 3 min of treatment.

Column optimization of adsorption and evaluation of bed parameters-based on removal of arsenite ion using rice husk

The objective of this study deals with column optimization of adsorption-based on removal of arsenite ion using rice husk. The parameters affecting the column adsorption study, i.e., influent-concentration, bed depth, and flow rate, were optimized. The range of parameters, i.e., influent-concentration (15-50 mg/L), flow rate (20, 35, 45, and 60 mL/min), and bed depth (15-60 mm), were studied experimentally. Kinetics models Bohart-Adams and Hutchins were studied to measure the amount adsorbed, depth of mass transfer zone, saturated concentration, and time observed at 10% & 90% breakthrough. The percentage amount adsorbed q_m enhanced with enhancement in bed depth but got reduced with influent ions concentration and volumetric flow rate. Established model Bohart-Adams and Hutchins equations were used for calculation of mass transfer zone which came out to be 51 mm. An adsorption capacity (q_m) of 4.5 mg/g for arsenite ions was achieved at optimum parameter values of 60 mm of bed depth, 20 mL/min volumetric flow rate, and 50 mg/L of influent ions concentration. The adsorption bed parameters were also evaluated using Hutchins and Michaels equations. The column study proved rice husk to be a potential adsorbent for the adsorption of arsenite.

Removal efficiency of As(III) from aqueous solutions using natural and Fe(III) modified bentonites

Contamination of water with arsenic is a major global health problem. The use of adsorbent materials for the removal of As from aqueous systems is a plausible solution to this problem. In this work, the use of commercial bentonites (purified and modified with iron (III)) for the removal of As from water was studied. The samples were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier Transformed Infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and nitrogen adsorption/desorption isotherms to determine their physicochemical properties. The arsenic removal capacities of adsorbent materials were studied from 1 mg/L solutions of As (III) using the colorimetric technique of molybdenum blue. High adsorption capacity (0.33 mg/g) of As (III) was obtained in aqueous systems after 1 h of treatment with unmodified bentonite. The incorporation of iron improved the removal performance in short times. The obtained results could be the starting point for the development of a low-cost filtration system that contributes to solve the problem of arsenic in water.

Removal of Arsenic from Wastewater by Using Nano Fe3O4/Zinc Organic Frameworks

Efficient removal of arsenic in wastewater is of fundamental importance due to the increasingly severe arsenic pollution. In this study, a new composite adsorbent (Fe₃O₄@ZIF-8) for As(V) removal from wastewater was synthesized by encapsulating magnetic Fe₃O₄ nanoparticles into metal organic frameworks. In order to evaluate the feasibility of Fe₃O₄@ZIF-8 as an adsorbent for As(V) removal, the adsorption properties of Fe₃O₄@ZIF-8 were systematically explored by studying the effects of dosage, pH, adsorption isotherm, kinetics, and thermodynamics. Additionally, the characterization of Fe₃O₄@ZIF-8 before and after adsorption was analyzed thoroughly using various tests including SEM-EDS, XPS, BET, XRD, TG, FTIR, and the properties and arsenic removal mechanism of the Fe₃O₄@ZIF-8 were further studied. The results showed that the Fe₃O₄@ZIF-8 has a specific surface area of 316 m²/g and has excellent adsorption performance. At 25 °C, the initial concentration of arsenic was 46.916 mg/L, and pH 3 was the optimum condition for the Fe₃O₄@ZIF-8 to adsorb arsenic. When the dosage of the Fe₃O₄@ZIF-8 was 0.60 g/L, the adsorption of arsenic by the Fe₃O₄@ZIF-8 can reach 76 mg/g, and the removal rate can reach 97.20%. The adsorption process of arsenic to the Fe₃O₄@ZIF-8 can be well described by the Langmuir isotherm model and the second-order kinetic equation. At pH 3 and temperature 298 K, the maximum adsorption capacity of arsenic by the Fe₃O₄@ZIF-8 was 116.114 mg/g. Through the analysis of thermodynamic parameters, it is proved that the adsorption process of arsenic by the Fe₃O₄@ZIF-8 is a spontaneous endothermic reaction. The Fe₃O₄@ZIF-8 has broad prospects for removing As(V) pollution in wastewater, because of its strong adsorption capacity, good water stability, and easy preparation.

Remediation of heavy metal polluted waters using activated carbon from lignocellulosic biomass: An update of recent trends

The use of a cheap and effective adsorption approach based on biomass-activated carbon (AC) to remediate heavy metal contamination is clearly desirable for developing countries that are economically disadvantaged yet have abundant biomass. Therefore, this review provides an update of recent works utilizing biomass waste-AC to adsorb commonly-encountered adsorbates like Cr, Pb, Cu, Cd, Hg, and As. Various biomass wastes were employed in synthesizing AC via two-steps processing; oxygen-free carbonization followed by activation. In recent works related to the activation step, the microwave technique is growing in popularity compared to the more conventional physical/chemical activation method because the microwave technique can ensure a more uniform energy distribution in the solid adsorbent, resulting in enhanced surface area. Nonetheless, chemical activation is still generally preferred for its ease of operation, lower cost, and shorter preparation time. Several mechanisms related to heavy metal adsorption on biomass wastes-AC were also discussed in detail, such as (i) - physical adsorption/deposition of metals, (ii) - ion-exchange between protonated oxygen-containing functional groups (-OH, -COOH) and divalent metal cations (M²⁺), (iii) - electrostatic interaction between oppositely-charged ions, (iv) - surface complexation between functional groups (-OH, O^2-, -CO-NH-, and -COOH) and heavy metal ions/complexes, and (v) - precipitation/co-precipitation technique. Additionally, key parameters affecting the adsorption performance were scrutinized. In general, this review offers a comprehensive insight into the production of AC from lignocellulosic biomass and its application in treating heavy metals-polluted water, showing that biomass-originated AC could bring great benefits to the environment, economy, and sustainability.

A Combined CFD-Response Surface Methodology Approach for Simulation and Optimization of Arsenic Removal in a Fixed Bed Adsorption Column

An experimentally validated CFD model was developed for lab-scale arsenic (As) fixed-bed columns using COMSOL Multiphysics. The effects of key factors such as the adsorbent bed depth, the feed flow rate, and the initial As concentration (conc.) on the overall As removal performance were investigated. Subsequently, the CFD was combined with response surface methodology (RSM) to optimize process conditions and examine main and interaction effects of these factors on model responses, i.e., the As removal efficiency and the bed saturation time. The ANOVA results suggested that quadratic regression models were highly significant for both responses. The established regression model equations predicted the response values closer to CFD measurements. It was found that, compared with the initial As conc. and the feed flow rate, the effect of the bed depth was more significant. Moreover, both the As removal efficiency and the bed saturation time were increased reasonably with the increasing bed depth and decreased with the increasing feed flow rate and initial As conc. The optimum conditions for the As removal process were obtained as the bed height of 80 cm, the initial As concentration of 2.7 mmol/m3, and the feed flow rate of 1 L/min. The present combined CFD−RSM approach is a useful guideline in overall design and optimization of various lab-scale and industrial applications for removal of As from wastewater.

Uptake of arsenic(V) using iron and magnesium functionalized highly ordered mesoporous MCM-41 (Fe/Mg-MCM-41) as an effective adsorbent

Mesoporous silica (MCM-41) is widely used as a supporting material due to its large specific surface area and good stability, but it cannot remove heavy metals due to the lack of adsorption active sites. In this study, the MCM-41 (a mesoporous SiO₂ material) decorated with iron and magnesium oxide (Fe/Mg-MCM-41) was found to be an excellent adsorbent to remove arsenic(V) from water. FTIR, BET, TEM-EDS, XRD, XPS, etc. were applied for characterization analysis. Adsorption isotherms were fitted well by the Langmuir model and the experimental maximum adsorption capacity of Fe/Mg₄-MCM-41 (magnesium accounts for 4%) was 71.53 mg/g at pH = 3. Thermodynamics analysis suggested exothermic nature of adsorption behavior. Kinetic process was well described by the pseudo-second-order model and adsorption rate was controlled by intraparticle diffusion and film diffusion. Moreover, the adsorption behavior of As(V) onto Fe/Mg₄-MCM-41 was investigated under different reaction conditions, such as pH, temperature, Mg-doping and competing ions. The results showed that loading a certain amount of magnesium can significantly improve arsenic removal efficiency. Additionally, Fe/Mg₄-MCM-41 exhibits high arsenic(V) removal in the wide pH range of 3-10. The Fe/Mg₄-MCM-41 can be regenerated and used after four consecutive cycles. The high arsenic(V) sorption capacity, wide range of pH applications, ability to regenerate, and reusability of Fe/Mg₄-MCM-41 confirmed that this adsorbent is promising for treating As-contaminated wastewater.

The research trend on arsenic pollution in freshwater: a bibliometric review

We conducted a quantitative and qualitative bibliometric analysis based on 8740 research articles from the Web of Science Core Collection published in the last 20 years (2000-2020) for a better understanding of the research progress and development trend of arsenic pollution in freshwater (FAP). The results showed a significant increase in the number of publications from 2007 to 2020, especially after 2015. Four of the top 10 productive authors are from China. Two of the top three research institutions are from China, and the publications of Chinese Academy of Sciences accounted for 5.40% of the total. China is also the center of the national cooperation network, indicating a greater influence of China in this scientific research field. The top three journals included Science of the Total Environmental, Environmental Science Technology, and Journal of Hazardous Materials. Besides arsenic, the high-frequency keywords in this field included adsorption, contamination, groundwater, removal, detection, and geochemistry. The researchers mainly focused on the groundwater environment, as well as the pollution hazards of arsenic in water bodies, remediation techniques, detection, migration, and transformation. Studies should pay more attention to the application and development of phytoremediation technology in the field of FAP in the future.

Spatial and temporal distribution of arsenic contamination in groundwater of Nawalparasi-West, Nepal: an investigation with suggested countermeasures for South Asian Region

Nawalparasi-West/Parasi is one of the severely affected districts in the Terai lowlands of Nepal by arsenic (As) contamination in groundwater, exceeding standards of 10 ppb (WHO) and 50 ppb (Nepal Drinking Water Standard). This study presents the spatial and temporal distribution of As across 6 km × 10 km region in Parasi via meteorological, hydrogeological, physio-chemical, and sedimentological investigations in 31 communities for about 5 years. In this study, water balance analysis was carried out for understanding the groundwater dynamics in the study area and its contribution to As elution. Gentle flow gradient and little to no infiltration was observed in the central region with relatively impervious silty clayey flood plain, where higher As concentrations were obtained compared to the northern Siwalik foothills and southern parts with coarser sediments. Similarly, higher As concentration (1048 ppb) was recorded in the drier pre-monsoon season than the wet season (529 ppb). The aquifer at 12 to 23 m depth feeding 73% wells in the study area exhibited higher As concentration in reduced environment as opposed to the oxidizing state at 5- to 6-m and 30- to 50-m deep aquifers. Other constituents such as Fe, B, and Cr and their relation with As were analyzed. The results of GERAS model analysis done for health risk assessment are also presented which show that under long-term exposure, the residents in Parasi were undertaking intolerable cancer risk of 1.1 to 6.4 × 10^-3. This study further incorporates socio-economic sentiments vital to analyze, and propose sustainable and cheap countermeasures for immediate implementation to reduce As exposure and health risk in Nepal, which is also highly applicable for other affected regions in South Asian Region.

Efficient removal of arsenic from aqueous solution by continuous adsorption onto iron-coated cork granulates

The search for low-cost technologies for arsenic removal from water is in high demand due to its human toxicity, even at low concentrations. Adsorption can be a cost-effective water treatment technique if applied with inexpensive materials. Arsenic continuous removal by adsorption onto an alternative modified biosorbent, iron-coated cork granulates (ICG), was investigated in this work. Results showed that most experimental parameters of breakthrough curves (BTC) depend on flow rate, bed height, pH, and initial arsenic concentration. The temperature did not significantly affect arsenate removal in continuous mode; however, the adsorption capacity was affected in batch mode. The thermodynamic parameters suggest that the adsorption process is spontaneous and endothermic. The maximum adsorption capacity of ICG for As(V) removal at pH 3 was 4.2 ± 0.3 mg g^-1, calculated by Yan model fit (R² = 0.981), and for As(III) at pH 9 was 1.6 ± 0.2 mg g^-1 (R² = 0.994). ICG were able to treat As(V) from 100 µg L^-1 to under 10 µg L^-1 and 50 µg L^-1 for 895 and 1633 bed volumes, and As(III) for 569 and 861 bed volumes, respectively, both at pH 7. The application of ICG in arsenic oxyanions remediation was found to be effective under various conditions.

Adsorption of As(III) and As(V) from aqueous solution by magnetic biosorbents derived from chemical carbonization of pea peel waste biomass: Isotherm, kinetic, thermodynamic and breakthrough curve modeling studies

The purpose of this research was to investigate the adsorption of arsenic (As) from aqueous solutions using MPAC-500 and MPAC-600 (magnetic-activated carbons synthesized from the peel of Pisum sativum (pea) pyrolyzed at 500 °C and 600 °C temperatures, respectively). The potential of both biosorbents for As adsorption was determined in batch and column mode. The characterization of both biosorbents was performed by energy dispersive spectroscopy, scanning electron microscope, pHZPC, particle size distribution, X-ray diffraction, zeta potential and Fourier-transform infrared spectroscopy. It was found that the efficiency of MPAC-600 was better than MPAC-500 for the adsorption of As(III) and As(V) ions. The adsorption capacities of MPAC-500 and MPAC-600 in removing As(III) were 0.7297 mg/g and 1.3335 mg/g, respectively, while the values of Qmax for As(V) on MPAC-500 and MPAC-600 were 0.4930 mg/g and 0.9451 mg/g, respectively. The Langmuir isotherm model was found to be the best fit for adsorption of As(III) by MPAC-500 and MPAC-600, as well as adsorption of As(V) by MPAC-500. The Freundlich isotherm model, on the other hand, was optimal for As(V) removal with MPAC-600. With R2 values close to unity, the pseudo-second-order kinetics were best fitted to the adsorption process of both As species. The Thomas model was used to estimate the breakthrough curves. The effects of coexisting oxyanions and regeneration studies were also carried out to examine the influence of oxyanions on As adsorption and reusability of biosorbents.

Dynamic Adsorption of As(V) onto the Porous α-Fe2O3/Fe3O4/C Composite Prepared with Bamboo Bio-Template

Arsenic (As(V)), a highly toxic metalloid, is known to contaminate wastewater and groundwater and is difficult to degrade in nature. However, the development of highly efficient adsorbents, at a low cost for use in practical applications, remains highly challenging. Thus, to investigate the As(V) adsorption mechanism, a novel porous α-Fe2O3/Fe3O4/C composite (PC-Fe/C-B) was prepared, using bamboo side shoots as a bio-template, and the breakthrough performance of the PC-Fe/C-B composite-packed fixed-bed column in As(V) removal was evaluated, using simulated wastewater. The PC-Fe/C-B material accurately retained the hierarchical porous microstructure of the bamboo bio-templates, and the results demonstrated the great potential of PC-Fe/C-B composite, as an effective adsorbent for removing As(V) from wastewater, under the optimal experimental conditions of: influent flow 5.136 mL/min, pH 3, As(V) concentration 20 mg/L, adsorbent particle size < 0.149 mm, adsorption temperature 35 °C, PC-Fe/C-B dose 0.5 g, and breakthrough time 50 min (184 BV), with qe,exp of 21.0 mg/g in the fixed-bed-column system. The CD-MUSIC model was effectively coupled with the transport model, using PHREEQC software, to simulate the reactive transportation of As(V) in the fixed-bed column and to predict the breakthrough curve for column adsorption.

Modified Polymeric Biosorbents from Rumex acetosella for the Removal of Heavy Metals in Wastewater

The contamination of water resources by effluents from various industries often contains heavy metals, which cause irreversible damage to the environment and health. The objective was to evaluate different biosorbents from the weed Rumex acetosella to remove metal cations in wastewater. Drying, grinding and sieving of the stems was carried out to obtain the biomass, retaining the fractions of 250 to 500 µm and 500 to 750 µm, which served to obtain the biosorbents in natura (unmodified), acidic, alkaline, and mixed. Proximal analysis, PZC, TOC, removal capacity, influence of pH, functional groups, thermal analysis, structural characteristics, adsorption isotherms, and kinetic study were evaluated. The 250 µm mixed treatment was the one that presented the highest removal percentages, mainly due to the OH, NH, -C-H, COOH, and C-O functional groups achieving the removal of up to 96.14% of lead, 36.30% of zinc, 34.10% of cadmium and 32.50% of arsenic. For contact times of 120 min and an optimum pH of 5.0, a loss of cellulose mass of 59% at 328 °C and a change in the surface of the material were also observed, which allowed for obtaining a topography with greater chelating capacity, and the Langmuir and pseudo-second order models were better fitted to the adsorption data. The new biosorbents could be used in wastewater treatment economically and efficiently.