Molecular transformation of dissolved organic matter and the formation of disinfection byproducts in full-scale surface water treatment processes

Improved identification of chlorinated disinfection byproducts by the sequential elution and absorption mode

Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) has been extensively employed to characterize the chemodiversty of dissolved organic matter (DOM) including chlorinated disinfection byproducts (Cln-DBPs). However, little is known about the combined effects of the sequential solid phase extraction (SPE) and absorption mode of Fourier transform data processing on the identification of Cln-DBPs. In this study, the identification of Cln-DBPs by the sequential SPE extraction and absorption mode were systematically compared using a typical swimming pool water. The sequential SPE extraction was more effective in extracting DOM molecules including Cln-DBPs than the traditional extraction, yielding 48.2 % ± 2.1 % and 87.3 % ± 3.8 % more DOM molecules and Cln-DBPs molecules, respectively. Moreover, a total of 274 nitrogenous Cln-DBPs were identified by the sequential SPE extraction with 80 more than that by the traditional SPE. The absorption mode improved the resolution and the signal-to-noise values of DOM peaks by factors of 1.87-1.98 and 1.52-1.60, respectively. The number of resolved Cl-related mass doublets within 2 mDa mass difference in the absorption mode was 537 more than that in the magnitude mode. Overall, the combination of sequential elution and absorption modes facilitated the detection of more molecules of DOM and Cln-DBPs compared to traditional SPE in magnitude mode, with an increase of 92.7 % ± 2.1 % and 121.7 % ± 5.6 %, respectively. These results have highlighted the great potential of the sequential elution combined with absorption mode in improving the identification of Cln-DBPs and their precursors, facilitating the application of FT-ICR MS in the nontargeted analysis of emerging contaminants including Cln-DBPs at the molecular level.

Molecular-level insights of microplastic-derived soluble organic matter and heavy metal interactions in different environmental occurrences through EEM-PARAFAC and FT-ICR MS

The interactions between microplastic-derived dissolved organic matter (MPs-DOM) and heavy metals (Cu, Pb, and Cd) regulate the complex environmental transport behavior of pollutants in terrestrial and aquatic environments. In this study, fluorescence excited emission matrix spectroscopy combined with parallel factor analysis (EEM-PARAFAC) and electrospray ionization coupled Fourier transform ion cyclotron resonance mass spectrometry (ESI FT-ICR MS) were employed to investigate the complexation mechanism of MPs-DOM with heavy metals, as well as the effects of different environmental occurrences of MPs-DOM on the transport behaviors of heavy metals in saturated porous medium. The findings demonstrated that MPs-DOM, particularly humic-like substances containing aromatic structures and various oxygen functional groups, could form stable complexes with heavy metals. This interaction significantly altered the transport capacity of Pb and Cu in saturated porous media. It is noteworthy that MPs-DOM in the free and deposited states in the environment may have markedly disparate effects on heavy metal transport. MPs-DOM in the free state may facilitate the co-migration of heavy metal ions in porous media, thereby enhancing the mobility of heavy metals. In contrast, sedimentary-state MPs-DOM can retain heavy metals in porous media and inhibit their migration through complexation with them.

Changes in chemical characteristics and toxicity of fluoxetine and humic acid during chlorination

The coexistence of emerging pollutants and dissolved organic matter in wastewater complicates the transformation and generation of disinfection byproducts (DBPs) during chlorination treatment, which is essential for effective water quality evaluation and chlorination optimization. This study used fluoxetine (FLX) and humic acid (HA) as representative substances to analyze changes in their chemical characteristics and zebrafish embryonic developmental toxicity under different chlorination conditions. The analysis of the fluorescence characteristics and Fourier transform ion cyclotron resonance mass spectrometry indicated that chlorination treatment increased the aromatic compound content of the HA solution. FLX addition further increased the presence of aromatic ring structures and oxidized molecules, resulting in the formation of numerous Cl-DBPs with highly unsaturated and phenolic structures. Moreover, different responses in zebrafish embryo development and behavior were found with FLX, HA, and FLX + HA exposures. Cardiotoxicity was linked to changes in the concentration of cTn-I protein and expression of various genes. Prolonged chlorination conditions showed higher toxicities. Correlation analysis found a weak relation between chemical indicators and toxicity data, indicating that both analysis methods need to be considered when analyzing the impact of the chlorination. Further, a combination of chemical analyses and toxicity tests revealed that the FLX + HA solution with chlorination conditions of 3 mg/L for 30 min had lower chemical and toxic effects in this experiment. This study provides valuable scientific insights for the safe discharge of chlorinated water containing FLX and dissolved organic matter, as well as guidance for optimizing chlorination parameters in wastewater treatment.

Combination of oxidative and reductive effects of phenolic compounds on the degradation of aniline disinfection by-products by free radicals

In this study, we selected 13 phenolic compounds containing -COOH, -CHO, -OH, and -COCH3 functional groups as model compounds for dissolved organic matter (DOM), and explored the redox reactions during the co-degradation of phenolic compounds with aniline disinfection by-products (DBPs) at the molecular level. When phenolic compounds and aniline DBPs were degraded, phenoxy radicals and aniline radicals were the most important intermediates. Phenoxy radicals can degrade aniline DBPs via hydrogen atom abstraction (HAA) reactions, and the reaction rates were related to the reduction potentials of the compounds. Compounds containing electron-withdrawing groups were more likely to oxidize aniline DBPs. Aniline DBPs were more easily degraded by phenoxy radicals when they contained electron-donating groups, and the increase in the number of chlorine atoms inhibited the reaction rates of aniline DBPs degradation by phenoxy radicals. Although phenolic compounds can reduce aniline DBPs, there was no significant correlation between the reaction rates and the reduction potentials of the compounds. Considering the redox effects of phenolic compounds on aniline DBPs, co-degradation simulations showed that phenolics inhibited the degradation efficiency of aniline DBPs. This work provided new insights into the transformation mechanisms and degradation efficiencies of DOM and aniline DBPs when they were co-degraded.

Comparative investigation of known and unknown disinfection by-product precursor removal and microbial community from biological biochar and activated carbon filters

Biological activated carbon filter (BAC) is one of the most effective technologies for removing disinfection by-product (DBP) precursors from water. Biochar is a lower-cost medium that has the potential to replace granular activated carbon in BAC applications, thus leading to the development of biological biochar filter (BCF). This study compared BCF with BAC for the removal of DBP precursors using column experiments. Both BCF and BAC achieved the removal of DBP precursors, resulting in concentrations of all DBP formation potential below the World Health Organization guideline values for drinking water. Bromodichloromethane and unknown DBP precursor removal by BCF was comparable to that by BAC. However, BAC removed more chloroform and dichloroacetontrile precursors than BCF. For microbial community analysis, cell numbers in a bottom layer (inlet) of BCF and BAC columns were higher than those in the top layer. The abundances of Nordella and a microbial genus from Burkholderiaceae at the bottom layer showed a strong correlation to the number of DBP precursors removed and were comparable in BCF and BAC. This finding likely contributes to the similarities between DBPs species removed and the removal performances of some known and unknown DBP precursors by BCF and BAC. Overall results from this study revealed that biochar can be served as a low-cost and sustainable replacement of activated carbon in water filter for DBP precursor removal.

Photochemical Transformation of Dissolved Organic Matter in Surface Water Augmented the Formation of Disinfection Byproducts

Sunlight may lead to changes in disinfection byproducts (DBPs) formation potentials of source water via transforming dissolved organic matter (DOM); however, the underlying mechanisms behind these changes remain unclear. This work systematically investigated the effect of photochemical transformation of DOM from reservoir water (DOMRe) and micropolluted river water (DOMRi) after 36 h of simulated sunlight irradiation (equivalent to one month under natural sunlight) on DBPs formation. Upon irradiation, high molecular weight (MW) and aromatic molecules tended to be mineralized or converted into low-MW and highly oxidized (O/C > 0.5) ones which might react with chlorine to generate high levels of DBPs, resulting in an elevation in the yields (μg DBP/mg C) of almost all the measured DBPs and the quantities of unknown DBPs in both DOM samples after chlorination. Additionally, DOMRi contained more aromatic molecules susceptible to photooxidation than DOMRe. Consequently, irradiated DOMRi exhibited a greater increase in the formation potentials of haloacetonitriles, halonitromethanes, and specific regulated DBPs, with nitrogenous DBPs being responsible for the overall rise in the calculated cytotoxicity following chlorination. This work emphasized the importance of a comprehensive removal of phototransformation products that may serve as DBPs precursors from source waters, especially from micropolluted source waters.

Purification of dredged water by magnetic coagulation: Response surface optimization and dissolved organic matter removal characteristics

In the present study, magnetic coagulation was used to treat dredged water and the response surface method was used to optimize process parameters. The dissolved organic matter (DOM) removal characteristics were characterized by three-dimensional fluorescence spectrometry and ultra-high resolution mass spectrometry. During the magnetic coagulation process, the suspended solids (SS) removal rate increased initially and then decreased under conditions of increasing magnetic powder dosage and stirring rate. After magnetic coagulation and precipitation for 20 min, the contents of SS, ammonia nitrogen, chemical oxygen demand, and total phosphorus in the treated dredged water met the requirements of the discharge standard (GB8978-1996, China). Three-dimensional fluorescence results showed that magnetic coagulation selectively removed fulvic acids and humic acid substances. After magnetic coagulation with precipitation for 10 min and 20 min, the total relative content of lignins, tannins, proteins, lipids, aminosugars, unsaturated hydrocarbons, condensed aromatic structures, and carbohydrates decreased by 26.3% and 39.4%, respectively. After magnetic coagulation, the distribution range of small molecule DOM shifted to the low H/C and high O/C regions. This study provides a novel perspective for studies on the removal of DOM in dredged water by magnetic coagulation. PRACTITIONER POINTS: SS and DOM removal were significantly enhanced by the use of magnetic coagulation. SS removal efficiency was affected by stirring rate and magnetic powder dosage. Magnetic coagulation selectively removed fulvic acids and humic acid substances. DOM molecule shifted to low H/C and high O/C regions after magnetic coagulation.

Phototransformation of Brominated Disinfection Byproducts and Toxicity Elimination in Sunlit-Ozonated Reclaimed Water

Ozonation is universally used during water treatment but can form hazardous brominated disinfection byproducts (Br-DBPs). While sunlight exposure is advised to reduce the risk of Br-DBPs, their phototransformation pathways remain insufficiently understood. Here, sunlight irradiation was found to reduce adsorbable organic bromine by 63%. Applying high-resolution mass spectrometry, the study investigated transformations of dissolved organic matter in sunlit-ozonated reclaimed water, revealing the number and abundance of assigned formulas decreased after irradiation. The Br-DBPs with O/C < 0.6 and MW > 400 Da were decreased or removed after irradiation, with the majority being CHOBr compounds. The peak intensity reduction ratio of CHOBr compounds correlated positively with double bound equivalent minus oxygen ratios but negatively with O/C, suggesting that photo-susceptible CHOBr compounds were highly unsaturated. Mass difference analysis revealed that the photodegradation pathways were mainly oxidation aligned with debromination. Three typical CHOBr molecular structures were resolved, and their photoproducts were proposed. Toxicity estimates indicated decreased toxicity in these photoproducts compared to their parent compounds, in line with experimentally determined values. Our proposed phototransformation pathways for Br-DBPs enhance our comprehension of their degradation and irradiation-induced toxicity reduction in reclaimed water, further illuminating their transformation under sunlight in widespread environmental scenarios.

Effects of dissolved organic matter removal and molecular transformation in different water treatment processes on formation of disinfection byproducts

Alterations in molecular composition of dissolved organic matter (DOM) during water treatments can influence the composition and toxicity of disinfection by-products (DBPs) in subsequent chlorination disinfection process. In this study, the impacts of DOM composition after various water treatment techniques (coagulation, adsorption, nanofiltration, biological aerated filter (BAF), and their integrated processes) on the generation mechanisms of DBPs were comprehensively explored by Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) in combination with GC-MS and LC-MS analysis. The results indicated that coagulation preferentially removed unsaturated (low H/C) and oxidized (high O/C) compounds, whereas adsorption was prone to remove the reduced (low O/C) component that was more reactive with chlorine, leading to lower yields (μg DBP/mg DOC) of trihalomethanes (THMs) and haloacetic acids (HAAs) during subsequent chlorination. The coagulation-adsorption technique exhibited a relatively high removal of both known and unknown DBPs, demonstrating that coagulation and adsorption were complementary for DOM removal at the molecular level. Nanofiltration selectively removed molecules with relatively high O/C, however, those with very low O/C that were more reactive with chlorine could pass through the nanofiltration membrane, resulting in the highest yields of THMs and HAAs. Although BAF was inefficient in removing DBPs precursors, it could convert molecules with low degree of oxidation and unsaturation into highly oxidized and unsaturated ones, thereby significantly enhancing the removal of DBPs precursors in the subsequent coagulation-adsorption process. These findings are instrumental in developing and selecting more effective techniques to minimize the formation of DBPs in water treatment.

Characteristics in dissolved organic matter and disinfection by-product formation during advanced treatment processes of municipal secondary effluent with Orbitrap mass spectrometry

Dissolved organic matter (DOM) is reported to be a precursor to disinfection by-products (DBPs), which have adverse effects on human health. Therefore, it is crucial to effectively remove DOM before water disinfection. Characteristics of DOM and DBPs formation during advanced treatment processes including coagulation, adsorption, ultraviolet (UV) irradiation, and ozone (O3) oxidation in municipal secondary effluent were investigated in this research. DOM was characterized by Fourier transform infrared spectroscopy (FTIR), excitation-emission matrix fluorescence spectroscopy (EEM), and Orbitrap mass spectrometry (Orbitrap MS). Moreover, DBPs formation potential under different advanced treatment processes was also discussed. FTIR results indicated that various functional groups existing in DOM may react with the disinfectant to form toxic DBPs. EEM analysis indicated that DOM in all water samples was dominated by soluble microbial product-like (SMPs) and humic acid-like (HA) substances. The municipal secondary effluent was abundant with DOM and rich in carbon, hydrogen, oxygen, and nitrogen atoms, contained a certain dosage of phosphorus and sulfur atoms, and the highest proportion is lignin. Most of the precursors (CHO features) had positive double bond equivalent subtracted oxygen per carbon [(DBE-O)/C] and negative carbon oxidation state (Cos) in all four different advanced treatment processes. DBPs formation potential (DBPFP) of coagulation, adsorption, UV irradiation, and O3 oxidation advanced treatment processes were 487 μg L-1, 586 μg L-1, 597 μg L-1, and 308 μg L-1, respectively. And the DBPs precursors removal efficiency of coagulation, adsorption, UV irradiation, and O3 oxidation advanced treatment processes were 50.8%, 40.8%, 39.8%, and 69.0%, respectively. This study provides in-depth insights into the changes of DOM in municipal secondary effluent at the molecular level and the removal efficiency of DBPs precursors during coagulation, adsorption, UV irradiation, and O3 oxidation advanced treatment processes.

Molecular insights towards changing behaviors of organic matter in a full-scale water treatment plant using FTICR-MS

The changing behavior of organic matter in a full-scale water treatment process was characterized based on the three-dimensional excitation-emission matrix (3D-EEM) and Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS). Polyaluminum chloride (PAC) as a coagulant can help to effectively remove soluble microbial by-products-like and aromatic protein-like substances during coagulation and sedimentation, corresponding to tannin and coagulated aromatic regions. The leakage of soluble microbial products during sand filtration resulted in an increase in the intensity of biomass-like regions. Nitrogen-containing compounds have higher weighted average value of double bond equivalents (DBE_w) and the modified aromaticity index (AI_mod-w) than nitrogen-free compounds. Water treatment can preferentially remove unsaturated nitrogen-containing compounds with more O atoms and higher-oxidation-state carbon. The dissolved organic carbon (DOC) and UV₂₅₄ were not correlated well with changes in nitrogen-containing compounds due to the preferential removal of nitrogen-containing compounds. This study revealed the specificity of organic matter removal during water treatment, and it was helpful in optimizing treatment processes for various raw water to ensure water quality.