Improved performance of thin-film nanocomposite nanofiltration membranes as induced by embedded polydopamine-coated silica nanoparticles

Biomimetic 3D efficient fog harvester by synergistic wettability effect

By collecting water in the air, it is an important way to solve the problem of water shortage in arid and semi-arid areas. Improving the efficiency of fog harvesting is still a great challenge to be overcome. The use of 3D structure is an excellent strategy, here, a Multiple-biomimetic 3D hydrophilic and superhydrophobic fog harvester with a hump-valley structure was prepared by the combination of thermal processing and spraying. Inspired by biological water collection in nature, a 3D porous sponge surface with hydrophilic valley and superhydrophobic hump was obtained by two-step treatment. This surface structure showed excellent fog harvesting performance, which was 185 % higher than the original sponge. This structure accelerates the capture, transfer and transport of droplets during the fog harvesting process and greatly improves the efficiency of fog harvest. The results show that the chemical gradient and structural gradient actuation we constructed on the melamine sponge surface can effectively improve the fog collection efficiency. A surface with a linear hump-valley mixed wettability pattern is designed, and it is proved that fog collection efficiency can be effectively improved at the droplet capture and transfer stage and transport stage respectively. This study highlights a simple and cheap integrated fog harvester material design.

ZnO/PDA/Mesoporous Cellular Foam Functionalized Thin-Film Nanocomposite Membrane towards Enhanced Nanofiltration Performance

Thin-film nanocomposite (TFN) membranes are the third-generation membranes being explored for nanofiltration applications. Incorporating nanofillers in the dense selective polyamide (PA) layer improves the permeability-selectivity trade-off. The mesoporous cellular foam composite Zn-PDA-MCF-5 was used as a hydrophilic filler in this study to prepare TFN membranes. Incorporating the nanomaterial onto the TFN-2 membrane resulted in a decrease in the water contact angle and suppression of the membrane surface roughness. The pure water permeability of 6.40 LMH bar^-1 at the optimal loading ratio of 0.25 wt.% obtained was higher than the TFN-0 (4.20 LMH bar^-1). The optimal TFN-2 demonstrated a high rejection of small-sized organics (>95% rejection for 2,4-dichlorophenol over five cycles) and salts-Na₂SO₄ (≈95%) > MgCl₂ (≈88%) > NaCl (86%) through size sieving and Donnan exclusion mechanisms. Furthermore, the flux recovery ratio for TFN-2 increased from 78.9 to 94.2% when challenged with a model protein foulant (bovine serum albumin), indicating improved anti-fouling abilities. Overall, these findings provided a concrete step forward in fabricating TFN membranes that are highly suitable for wastewater treatment and desalination applications.

Thin-Film Nanocomposite (TFN) Membranes for Water Treatment Applications: Characterization and Performance

Thin-film nanocomposite (TFN) membranes have been widely investigated for water treatment applications due to their promising performance in terms of flux, salt rejection, and their antifouling properties. This review article provides an overview of the TFN membrane characterization and performance. It presents different characterization techniques that have been used to analyze these membranes and the nanofillers within them. The techniques comprise structural and elemental analysis, surface and morphology analysis, compositional analysis, and mechanical properties. Additionally, the fundamentals of membrane preparation are also presented, together with a classification of nanofillers that have been used so far. The potential of TFN membranes to address water scarcity and pollution challenges is significant. This review also lists examples of effective TFN membrane applications for water treatment. These include enhanced flux, enhanced salt rejection, antifouling, chlorine resistance, antimicrobial properties, thermal stability, and dye removal. The article concludes with a synopsis of the current status of TFN membranes and future perspectives.

Removal of natural organic matter from surface water sources by nanofiltration and surface engineering membranes for fouling mitigation - A review

Given that surface water is the primary supply of drinking water worldwide, the presence of natural organic matter (NOM) in surface water presents difficulties for water treatment facilities. During the disinfection phase of the drinking water treatment process, NOM aids in the creation of toxic disinfection by-products (DBPs). This problem can be effectively solved using the nanofiltration (NF) membrane method, however NOM can significantly foul NF membranes, degrading separation performance and membrane integrity, necessitating the development of fouling-resistant membranes. This review offers a thorough analysis of the removal of NOM by NF along with insights into the operation, mechanisms, fouling, and its controlling variables. In light of engineering materials with distinctive features, the potential of surface-engineered NF membranes is here critically assessed for the impact on the membrane surface, separation, and antifouling qualities. Case studies on surface-engineered NF membranes are critically evaluated, and properties-to-performance connections are established, as well as challenges, trends, and predictions for the field's future. The effect of alteration on surface properties, interactions with solutes and foulants, and applications in water treatment are all examined in detail. Engineered NF membranes containing zwitterionic polymers have the greatest potential to improve membrane permeance, selectivity, stability, and antifouling performance. To support commercial applications, however, difficulties related to material production, modification techniques, and long-term stability must be solved promptly. Fouling resistant NF membrane development would be critical not only for the water treatment industry, but also for a wide range of developing applications in gas and liquid separations.

Correlating the Role of Nanofillers with Active Layer Properties and Performance of Thin-Film Nanocomposite Membranes

Thin-film nanocomposite (TFN) membranes are emerging water-purification membranes that could provide enhanced water permeance with similar solute removal over traditional thin-film composite (TFC) membranes. However, the effects of nanofiller incorporation on active layer physico-chemical properties have not been comprehensively studied. Accordingly, we aimed to understand the correlation between nanofillers, active layer physico-chemical properties, and membrane performance by investigating whether observed performance differences between TFN and control TFC membranes correlated with observed differences in physico-chemical properties. The effects of nanofiller loading, surface area, and size on membrane performance, along with active layer physico-chemical properties, were characterized in TFN membranes incorporated with Linde Type A (LTA) zeolite and zeolitic imidazole framework-8 (ZIF-8). Results show that nanofiller incorporation up to ~0.15 wt% resulted in higher water permeance and unchanged salt rejection, above which salt rejection decreased 0.9-25.6% and 26.1-48.3% for LTA-TFN and ZIF-8-TFN membranes, respectively. Observed changes in active layer physico-chemical properties were generally unsubstantial and did not explain observed changes in TFN membrane performance. Therefore, increased water permeance in TFN membranes could be due to preferential water transport through porous structures of nanofillers or along polymer-nanofiller interfaces. These findings offer new insights into the development of high-performance TFN membranes for water/ion separations.

Incorporation of Functionalized Halloysite Nanotubes (HNTs) into Thin-Film Nanocomposite (TFN) Nanofiltration Membranes for Water Softening

Incorporating nanoparticles (NPs) into the selective layer of thin-film composite (TFC) membranes is a common approach to improve the performance of the resulting thin-film nanocomposite (TFN) membranes. The main challenge in this approach is the leaching out of NPs during membrane operation. Halloysite nanotubes (HNTs) modified with the first generation of poly(amidoamine) (PAMAM) dendrimers (G1) have shown excellent stability in the PA layer of TFN reverse-osmosis (RO) membranes. This study explores, for the first time, using these NPs to improve the properties of TFN nanofiltration (NF) membranes. Membrane performance was evaluated in a cross-flow nanofiltration (NF) system using 3000 ppm aqueous solutions of MgCl₂, Na₂SO₄ and NaCl, respectively, as feed at 10 bar and ambient temperature. All membranes showed high rejection of Na₂SO₄ (around 97-98%) and low NaCl rejection, with the corresponding water fluxes greater than 100 L m^-2 h^-1. The rejection of MgCl₂ (ranging from 82 to 90%) was less than that for Na₂SO₄. However, our values are much greater than those reported in the literature for other TFN membranes. The remarkable rejection of MgCl₂ is attributed to positively charged HNT-G1 nanoparticles incorporated in the selective polyamide (PA) layer of the TFN membranes.

An Overview of the Modification Strategies in Developing Antifouling Nanofiltration Membranes

Freshwater deficiency has become a significant issue affecting many nations' social and economic development because of the fast-growing demand for water resources. Nanofiltration (NF) is one of the promising technologies for water reclamation application, particularly in desalination, water, and wastewater treatment fields. Nevertheless, membrane fouling remains a significant concern since it can reduce the NF membrane performance and increase operating expenses. Consequently, numerous studies have focused on improving the NF membrane's resistance to fouling. This review highlights the recent progress in NF modification strategies using three types of antifouling modifiers, i.e., nanoparticles, polymers, and composite polymer/nanoparticles. The correlation between antifouling performance and membrane properties such as hydrophilicity, surface chemistry, surface charge, and morphology are discussed. The challenges and perspectives regarding antifouling modifiers and modification strategies conclude this review.

Enhanced Separation Performance of Polyamide Thin-Film Nanocomposite Membranes with Interlayer by Constructed Two-Dimensional Nanomaterials: A Critical Review

Thin-film composite (TFC) polyamide (PA) membrane has been widely applied in nanofiltration, reverse osmosis, and forward osmosis, including a PA rejection layer by interfacial polymerization on a porous support layer. However, the separation performance of TFC membrane is constrained by the trade-off relationship between permeability and selectivity. Although thin-film nanocomposite (TFN) membrane can enhance the permeability, due to the existence of functionalized nanoparticles in the PA rejection layer, the introduction of nanoparticles leads to the problems of the poor interface compatibility and the nanoparticles agglomeration. These issues often lead to the defect of PA rejection layers and reduction in selectivity. In this review, we summarize a new class of structures of TFN membranes with functionalized interlayers (TFNi), which promises to overcome the problems associated with TFN membranes. Recently, functionalized two-dimensional (2D) nanomaterials have received more attention in the assembly materials of membranes. The reported TFNi membranes with 2D interlayers exhibit the remarkable enhancement on the permeability, due to the shorter transport path by the "gutter mechanism" of 2D interlayers. Meanwhile, the functionalized 2D interlayers can affect the diffusion of two-phase monomers during the interfacial polymerization, resulting in the defect-free and highly crosslinked PA rejection layer. Thus, the 2D interlayers enabled TFNi membranes to potentially overcome the longstanding trade-off between membrane permeability and selectivity. This paper provides a critical review on the emerging 2D nanomaterials as the functionalized interlayers of TFNi membranes. The characteristics, function, modification, and advantages of these 2D interlayers are summarized. Several perspectives are provided in terms of the critical challenges for 2D interlayers, managing the trade-off between permeability, selectivity, and cost. The future research directions of TFNi membranes with 2D interlayers are proposed.

Plant Polyphenol Pyrogallol and Polyamine-Based Co-Deposition for High-Efficiency Nanofiltration Membrane Preparation towards Inorganic Salt Removal

The co-deposition between polyphenols and amines has been demonstrated in order to prepare positively charged nanofiltration (NF) membranes for multivalent cation rejection in recent years; however, the low reactivities of the involved polyphenols usually cause a long co-deposition time and unsatisfactory rejection. Herein, a novel plant polyphenol (PG) was co-deposited with tetraethylenepentamine (TEPA) in a much shorter time period to prepare positively charged NF with high multivalent cation rejection membranes. The performance of the co-deposition membranes can be easily controlled by adjusting the mass ratio of PG and TEPA, reaction time, and pH value of the buffer solution. The optimal membrane, prepared under a polyphenol and polyamine mass ratio of 1:1, coating time of 2 h, and pH value of 8.0, shows a decent pure water permeability of 8.43 L m^-2 h^-1 bar^-1 while maintaining a superior 96.24% MgCl₂ rejection. More importantly, the universality of this method was corroborated by employing other amines with different molecular weights in the co-deposition. This work provides new insights for the preparation of high-performance positively charged NF membranes.

Progress for Co-Incorporation of Polydopamine and Nanoparticles for Improving Membranes Performance

Incorporating polydopamine has become a viable method for membrane modification due to its universality and versatility. Fillers in their different categories have been confirmed as effective elements to improve the properties of membranes such as hydrophilicity, permeability, mechanical strength, and fouling resistance. Thus, this paper mainly highlights the recent studies that have been carried out using polydopamine and nanomaterial fillers simultaneously in modifying the performance of different membranes such as ultrafiltration, microfiltration, nanofiltration, reverse osmosis, and forward osmosis membranes according to the various modification methods. Graphene oxide nanoparticles have recently attracted a lot of attention among different nanoparticles used with polydopamine, due to their impressive characteristics impacts on enhancing membrane hydrophilicity, mechanical strength, and fouling resistance. Thus, the incorporation techniques of graphene oxide nanoparticles and polydopamine for enhancing membranes have been highlighted in this work. Moreover, different studies carried out on using polydopamine as a nanofiller for optimizing membrane performance have been discussed. Finally, perspectives, and possible paths of further research on mussel-inspired polydopamine and nanoparticles co-incorporation are stated according to the progress made in this field. It is anticipated that this review would provide benefits for the scientific community in designing a new generation of polymeric membranes for the treatment of different feed water and wastewater based on adhesive mussel inspired polydopamine polymer and nanomaterials combinations.

Polymer Nanocomposite Membrane for Wastewater Treatment: A Critical Review

With regard to global concerns, such as water scarcity and aquatic pollution from industries and domestic activities, membrane-based filtration for wastewater treatment has shown promising results in terms of water purification. Filtration by polymeric membranes is highly efficient in separating contaminants; however, such membranes have limited applications. Nanocomposite membranes, which are formed by adding nanofillers to polymeric membrane matrices, can enhance the filtration process. Considerable attention has been given to nanofillers, which include carbon-based nanoparticles and metal/metal oxide nanoparticles. In this review, we first examined the current status of membrane technologies for water filtration, polymeric nanocomposite membranes, and their applications. Additionally, we highlight the challenges faced in water treatment in developing countries.

Effect of the bio-inspired modification of low-cost membranes with TiO2:ZnO as microbial fuel cell membranes

Microbial fuel cells (MFCs) are a novel technique for converting biodegradable materials into electricity. In this study, the efficiency of mixed crystal (TiO₂:ZnO) as a membrane modifier of a low-cost, antifouling and self-cleaning cation exchange membrane for MFCs was studied. The modification was prepared using polydopamine (PDA) as the bio-inspired glue, followed by gravity deposition of a mixture of catalyst nanoparticles (TiO₂:ZnO 0.03%, 1:1 ratio) as anti-biofouling agents. The effects of the membrane modification were evaluated in terms of power density, open circuit potential, coulombic efficiency, anti-biofouling properties and also color and COD removal efficiency. The results showed that the use of the PDA-modified membrane and a mixture of catalysts facilitated the transfer of cations released during the oxidation process in the anodic compartment of the MFC, which increased the power generation in the MFC by 2.5 times and 5.7 times the current compared to pristine and PDA pristine membranes, decreased the MFC operating cycle time from 5 to 3 days, doubled the lifetime of the membranes and demonstrated higher COD removal efficiency and color removal. Finally, SEM and AFM analysis showed that the modification significantly minimized surface fouling. The modified membranes in this study proved to be a potential alternative to the expensive membranes currently used in MFCs, furthermore, this modification could be an interesting alternative modification for other potential membranes for use in MFCs, due to the fact that the catalyst activation was only performed with visible light (artificial and solar), which could decrease operating costs.

Development in nanomembrane-based filtration of emerging contaminants

Recently, the concentration of emerging contaminants is increasing in drinking water sources, industrial wastewater, and reclaimed water. It is not possible to remove the emerging contaminants using conventional methods, and the interest to use nanomembrane-based filtration is getting attention. A nanomembrane-based filtration can be manipulated without the use of any special equipment. Different research findings reported better removal of emerging contaminants has been achieved using nanomembrane-based filtration. Moreover, new developments have been examined and implemented at different levels and are expected to continue. Therefore, this chapter provides a brief overview of recent developments on nanomembrane-based filtration processes in the removal of emerging contaminants from drinking water sources, industrial wastewater, and reclaimed water.

Roughly Spherical: Tailored PMMA-SiO2 Composite Supraparticles with Optimized Powder Flowability for Additive Manufacturing

Particulate materials with well-engineered properties are of key importance for many aspects in our daily life. Polymer powders with high flowability, for example, play a crucial role in the emerging field of powder-based additive manufacturing processes. However, the polymer- and composite material selection for these technologies is still limited. Here, we demonstrate the design of spherical polymethyl methacrylate (PMMA) and PMMA-SiO₂ composite supraparticle powders with excellent powder flowability and tailored composition for powder-based additive manufacturing. Our process assembles these powders from the bottom up and affords a precise control over surface roughness and internal morphology via the choice of colloidal primary particles. We establish process-structure-property relationships connecting external spray-drying parameters and primary particle sizes with the resulting supraparticle roughness and, subsequently, with the macroscopic powder flowability and powder bed density. In a second step, we demonstrate the control of composition and internal morphology of PMMA-SiO₂ composite supraparticles based on different mass mixings and diameter ratios of the two primary particle dispersions. Finally, we successfully apply the prepared supraparticle powders in powder bed additive manufacturing. The optimized flowability of the composite powders allows the production of two-layered square specimens with fusion between the individual layers and a uniform and tunable distribution of nanoscale SiO₂ additives without requiring the addition of any flowing aids.

Preparation of Thin-Film Composite Nanofiltration Membranes Doped with N- and Cl-Functionalized Graphene Oxide for Water Desalination

In the present work, chemically modified graphene oxide (GO) was incorporated as a crosslinking agent into thin-film composite (TFC) nanofiltration (NF) membranes for water desalination applications, which were prepared by the interfacial polymerization (IP) method, where the monomers were piperazine (PIP) and trimesoyl chloride (TMC). GO was functionalized with monomer-containing groups to promote covalent interactions with the polymeric film. The composite GO/polyamide (PA) was prepared by incorporating amine and acyl chloride groups into the structure of GO and then adding these chemical modified nanomaterial during IP. The effect of functionalized GO on membrane properties and performance was investigated. Chemical composition and surface morphology of the prepared GO and membranes were analyzed by thermogravimetric analysis (TGA), Raman spectroscopy, FTIR spectroscopy, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and transmission electron microscopy (TEM). The fabricated composite membranes exhibited a significant increase in permeance (from 1.12 to 1.93 L m^-2 h^-1 bar^-1) and salt rejection for Na₂SO₄ (from 95.9 to 98.9%) and NaCl (from 46.2 to 61.7%) at 2000 ppm, when compared to non-modified membranes. The amine- and acyl chloride-functionalized GO showed improved dispersibility in the respective phase.

Study of Turbulence Promoters in Prolonging Membrane Life

Nanofiltration membrane technology is an effective method for secondary treated sewage purification. However, membrane fouling, which is inevitable in the membrane-separation process, can reduce membrane performance and shorten membrane life. Installing a turbulence promoter is a promising means of improving the hydraulic conditions inside the membrane chamber. In this study, the effect of turbulence promoter on prolonging membrane life was studied for the first time. Flat-sheet polyethersulfone nanofiltration membrane was used to filter humic acid solution, used for simulating secondary treated sewage. By comparing photographs and SEM images of the membrane before and after the simulated secondary treated sewage filtration, it was found that humic acid tended to be deposited on the low-velocity region, which was reflected by COMSOL simulation. After incorporating a turbulence promoter, the reduction of the humic acid deposition area and membrane fouling resistance indicated that the turbulence promoter could reduce membrane fouling due to the improved hydraulic conditions. Additionally, the turbulence promoter also increased the flux and reduced the flux decay rate. The turbulence promoter was then place in the crossflow flat-sheet membrane filtration module, and the variation of flux with time was tested in simulated secondary treated sewage with different concentrations. The results showed that the membrane life for the filtration of simulated secondary treated sewage comprising 50, 250, and 500 ppm humic acid increased by 23.1%, 80.4%, and 85.7%, respectively. The results of this article can serve as a reference for the prediction of membrane life and the performance enhancement mechanism of membranes containing a turbulence promoter.

Metal ferrite incorporated polysulfone thin-film nanocomposite membranes for wastewater treatment

Effluents from food, fermentation, and sugar industries contain a large quantity of glucose which has to be removed to limit the chemical oxygen demand (COD) of the water discharged. This work proposes novel thin-film nanocomposite (TFN) membranes incorporated with MgFe₂O₄ and ZnFe₂O₄ nanoparticles to address this concern. The nanoparticles synthesized by the sol-gel method was extensively characterized and then incorporated into the active polyamide layer of the thin-film composite polysulfone membranes. The change in membrane morphology, wettability, chemical structure, and mechanical strength with the incorporation of nanoparticles was studied in detail. Membranes with 0.005 wt.% MgFe₂O₄ nanoparticle exhibited highest glucose rejection (96.52 ± 2.35%) at 10 bar, 25 °C, and sufficiently high pure water flux (50.54 ± 1.92 L/m²h). This membrane also displayed 69.1 ± 5.12% salt rejection when challenged with 2000 ppm synthetic NaCl solution.

A Critical Review on Thin-Film Nanocomposite Membranes with Interlayered Structure: Mechanisms, Recent Developments, and Environmental Applications

The separation properties of polyamide reverse osmosis and nanofiltration membranes, widely applied for desalination and water reuse, are constrained by the permeability-selectivity upper bound. Although thin-film nanocomposite (TFN) membranes incorporating nanomaterials exhibit enhanced water permeance, their rejection is only moderately improved or even impaired due to agglomeration of nanomaterials and formation of defects. A novel type of TFN membranes featuring an interlayer of nanomaterials (TFNi) has emerged in recent years. These novel TFNi membranes show extraordinary improvement in water flux (e.g., up to an order of magnitude enhancement) along with better selectivity. Such enhancements can be achieved by a wide selection of nanomaterials, ranging from nanoparticles, one-/two-dimensional materials, to interfacial coatings. The use of nanostructured interlayers not only improves the formation of polyamide rejection layers but also provides an optimized water transport path, which enables TFNi membranes to potentially overcome the longstanding trade-off between membrane permeability and selectivity. Furthermore, TFNi membranes can potentially enhance the removal of heavy metals and micropollutants, which is critical for many environmental applications. This review critically examines the recent developments of TFNi membranes and discusses the underlying mechanisms and design criteria. Their potential environmental applications are also highlighted.

Progress of Interfacial Polymerization Techniques for Polyamide Thin Film (Nano)Composite Membrane Fabrication: A Comprehensive Review

In this paper, we review various novel/modified interfacial polymerization (IP) techniques for the fabrication of polyamide (PA) thin film composite (TFC)/thin film nanocomposite (TFN) membranes in both pressure-driven and osmotically driven separation processes. Although conventional IP technique is the dominant technology for the fabrication of commercial nanofiltration (NF) and reverse osmosis (RO) membranes, it is plagued with issues of low membrane permeability, relatively thick PA layer and susceptibility to fouling, which limit the performance. Over the past decade, we have seen a significant growth in scientific publications related to the novel/modified IP techniques used in fabricating advanced PA-TFC/TFN membranes for various water applications. Novel/modified IP lab-scale studies have consistently, so far, yielded promising results compared to membranes made by conventional IP technique, in terms of better filtration efficiency (increased permeability without compensating solute rejection), improved chemical properties (crosslinking degree), reduced surface roughness and the perfect embedment of nanomaterials within selective layers. Furthermore, several new IP techniques can precisely control the thickness of the PA layer at sub-10 nm and significantly reduce the usage of chemicals. Despite the substantial improvements, these novel IP approaches have downsides that hinder their extensive implementation both at the lab-scale and in manufacturing environments. Herein, this review offers valuable insights into the development of effective IP techniques in the fabrication of TFC/TFN membrane for enhanced water separation.

Feasibility of brackish water and landfill leachate treatment by GO/MoS2-PVA composite membranes

Two-dimensional (2D) based layered materials with tunable chemical functionalities and surface charge properties have emerged for on-demand applications including membrane technology. However, the process control, time and energy-efficient production of non-swelling graphene oxide (GO) with retaining physicochemical properties are still challenging. In this work, we have fabricated highly ordered GO membrane on cellulose acetate supporting membrane filters of 1.2 μm pore size using molybdenum disulphide (MoS₂) as a nano-spacer and polyvinyl alcohol (PVA) as an adhesive for the first time with limited swelling. The fabricated membranes were used for NaCl rejection and removal of toxic heavy metal ions, and the radioactive element from landfill leachate water. The introduction of hydrophilic PVA, thickness control using a various amount of nanospacer and graphene oxide played a vital role in the transport mechanism, permeability, and selectivity index. The composition of PVA and MoS₂ in the coating solution was optimized to tune the d-spacing of graphene oxide layers. The newly developed composite membranes have 89% rejection rate to NaCl and 3.96 L/m²h water flux at low operating pressures of 5 bar. Also, the prepared membranes have a high rejection of multivalent metal ions in landfill leachate. 86.5% to 99.8% rejection rate of multivalent metal ions in landfill leachate was observed for the M₃ (GO ₍₁₀₎: MoS_{2 (10)}: PVA _(0.5)) membrane. The excellent rejection performance is ascribed to the combined impact of size exclusion, ion adsorption, electrostatic interaction and Gibbs-Donnan exclusion mechanism. The excellent stability and high rejection rate even after 216 h of operation make the fabricated membranes promising for use in practical water separation applications.

Assessing the Performance of Thin-Film Nanofiltration Membranes with Embedded Montmorillonites

In this study, the basal spacing of montmorillonite (MMT) was modified through ion exchange. Two kinds of MMT were used: sodium-modified MMT (Na-MMT) and organo-modified MMT (O-MMT). These two particles were incorporated separately into the thin-film nanocomposite polyamide membrane through the interfacial polymerization of piperazine and trimesoyl chloride in n-hexane. The membrane with O-MMT (TFNO-MMT) has a more hydrophilic surface compared to that of membrane with Na-MMT (TFNNa-MMT). When various types of MMT were dispersed in the n-hexane solution with trimesoyl chloride (TMC), O-MMT was well-dispersed than Na-MMT. The poor dispersion of Na-MMT in n-hexane led to the aggregation of Na-MMT on the surface of TFNNa-MMT. TFNO-MMT displayed a uniform distribution of O-MMT on the surface, because O-MMT was well-dispersed in n-hexane. In comparison with the pristine and TFNNa-MMT membranes, TFNO-MMT delivered the highest pure water flux of 53.15 ± 3.30 L∙m-2∙h-1 at 6 bar, while its salt rejection for divalent ions remained at 95%-99%. Furthermore, it had stable performance in wide operating condition, and it exhibited a magnificent antifouling property. Therefore, a suitable type of MMT could lead to high separation efficiency.

A microfluidic approach to micromembrane synthesis for complex release profiles of nanocarriers

Physically crosslinked microscale biomembranes synthesized from pure chitosan are designed and demonstrated for pH-triggered release of embedded functionalized mesoporous silica nanoparticles. Nanoparticle-loaded membranes are formed in a microfluidic channel at the junction between accurately controlled co-flowing streams to achieve highly tuneable membrane properties. After formation, the loaded membranes remain stable until contact with physiological acidic conditions, resulting in controlled nanoparticle release. Furthermore, nanoparticle-loaded membranes with complex layered architectures are synthesized using different flow schemes, thus enabling customized nanoparticle release profiles. These novel materials are well-suited for integration within small medical devices as well as off-chip applications.