UV and solar TiO(2) photocatalysis of brevetoxins (PbTxs)

BTXs removals by modified clay during mitigation of Karenia brevis bloom: Insights from adsorption and transformation

Harmful algal blooms (HABs), especially those caused by toxic dinoflagellates, are spreading in marine ecosystems worldwide. Notably, the prevalence of Karenia brevis blooms and potent brevetoxins (BTXs) pose a serious risk to public health and marine ecosystems. Therefore, developing an environmentally friendly method to effectively control HABs and associated BTXs has been the focus of increasing attention. As a promising method, modified clay (MC) application could effectively control HABs. However, the environmental fate of BTXs during MC treatment has not been fully investigated. For the first time, this study revealed the effect and mechanism of BTX removal by MC from the perspective of adsorption and transformation. The results indicated that polyaluminium chloride-modified clay (PAC-MC, a typical kind of MC) performed well in the adsorption of BTX2 due to the elevated surface potential and more binding sites. The adsorption process was a spontaneous endothermic process that conformed to pseudo-second-order adsorption kinetics (k2 = 6.8 × 10-4, PAC-MC = 0.20 g L-1) and the Freundlich isotherm (Kf = 55.30, 20 °C). In addition, detailed product analysis using liquid chromatography-mass spectrometry/mass spectrometry (LC-MS/MS) indicated that PAC-MC treatment effectively removed the BTX2 and BTX3, especially those in the particulate forms. Surprisingly, PAC-MC could promote the transformation of BTX2 to derivatives, including OR-BTX2, OR-BTX3, and OR-BTX-B5, which were proven to have lower cytotoxicity.

Treatment of the red tide dinoflagellate Karenia brevis and brevetoxins using USEPA-registered algaecides

The effectiveness of USEPA-registered algaecides for managing algae in lakes and reservoirs has been extensively evaluated in laboratory studies, mesocosm studies and in situ treatment. However, the use of these algaecides in marine environments for the management of dinoflagellates and associated toxins remains largely unknown. Karenia brevis is a toxic dinoflagellate that causes red tides in the Gulf of Mexico. In this study, we investigated the efficacy of six USEPA-registered algaecides, three copper-based and three peroxide-based, on treating toxic K. brevis with a natural bloom density (1.79 × 10⁷ cells/L). Our results indicate that the application of as low as 0.31-0.34 mg Cu/L led to a significant decrease of K. brevis cells within 24 h after treatment, while peroxide-based algaecides required a relatively higher concentration for the effective removal of K. brevis cells (4.89-7.08 mg H₂O₂/L), but still lower than maximum label rate. Total brevetoxin levels 72 h after treatment revealed that 1.00 mg Cu/L for Algimycin® PWF, 6.48 mg H₂O₂/L for PAK® 27 and 7.08 mg H₂O₂/L for Oximycin® P5 had the greatest impact on decreasing toxin levels. The correlation analysis showed that brevetoxin reduction rate was significantly positively related with the peroxide-based algaecide exposure concentration, which is caused by the oxidation of hydroxyl radicals produced by hydrogen peroxide. The degradation dynamics of the three peroxide-based algaecides revealed that salinity, microorganisms and organic matter (≥ 0.2 μm) impact the stability of hydrogen peroxide, and Oximycin® P5 showed the highest stability among tested peroxide-based algaecides with a degradation rate of 0.467 mg/d in natural seawater. Hence, our laboratory work provided new insights into potential emergency treatment methods for immediate mitigation of K. brevis and brevetoxins. More work on the fate and persistence of algaecide active ingredients and phycotoxins, effects of site characteristics, and pilot studies on marine non-targets are still needed before safe application of this method for HABs in marine systems.

Compound-specific isotopic analysis to characterize the photocatalytic reaction of TiO2 nanoparticles with diethyl phthalate

In this study compound-specific isotope analysis (CSIA) has been used to explore the degradation mechanism of nano titanium dioxide (TiO₂) catalyzes photodegradation of diethyl phthalate (DEP). TiO₂ is a popular photosensitizer with potential in waste water treatment and application in advanced oxidation processes. The degradation process of DEP can be described with a first-order kinetics in the applied concentration ranges. The larger degradation rate constant has been found at neutral conditions. The ¹³C and ²H isotope fractionation associated with the nano TiO₂ catalyzes photodegradation of DEP at pH 3, 7 and 11 yield normal isotope effects. In the TiO₂/UV/DEP and TiO₂/H₂O₂/UV/DEP systems, the correlation of ¹³C and ²H fractionation (Λ) were calculated to be 2.7 ± 0.2, 2.8 ± 0.2 at pH 3, 2.2 ± 0.4, 2.5 ± 0.2, 2.3 ± 0.6 at pH 7 and 2.6 ± 0.3, 2.2 ± 0.3, 2.7 ± 0.2 and 2.3 ± 0.3 at pH11, respectively. The dominant free radical species in studied systems were explored by combining free radical quenching method and electron paramagnetic resonance analysis. The hydroxyl radicals have been found as the main radical species at all pH conditions studied. Furthermore, the ¹³C and ²H fractionation suggested that the addition of •OH on the benzene ring of DEP is the main conversion pathway. Therefore, CSIA is a promising technology for the identification of reaction pathways of DEP for example in water treatment systems.

Natural Polyether Ionophores and Their Pharmacological Profile

This review is devoted to the study of the biological activity of polyether ionophores produced by bacteria, unicellular marine algae, red seaweeds, marine sponges, and coelenterates. Biological activities have been studied experimentally in various laboratories, as well as data obtained using QSAR (Quantitative Structure-Activity Relationships) algorithms. According to the data obtained, it was shown that polyether toxins exhibit strong antibacterial, antimicrobial, antifungal, antitumor, and other activities. Along with this, it was found that natural polyether ionophores exhibit such properties as antiparasitic, antiprotozoal, cytostatic, anti-mycoplasmal, and antieczema activities. In addition, polyethers have been found to be potential regulators of lipid metabolism or inhibitors of DNA synthesis. Further study of the mechanisms of action and the search for new polyether ionophores and their derivatives may provide more effective therapeutic natural polyether ionophores for the treatment of cancer and other diseases. For some polyether ionophores, 3D graphs are presented, which demonstrate the predicted and calculated activities. The data presented in this review will be of interest to pharmacologists, chemists, practical medicine, and the pharmaceutical industry.

Characterization of Atmospheric Processes of Brevetoxins in Sea Spray Aerosols from Red Tide Events

Atmospheric processes can affect the longevity of harmful toxins in sea spray aerosols (SSA). This study characterized the degradation of brevetoxin (BTx) in SSA under different environmental conditions. The samples of seawater collected during a Karenia brevis bloom in Manasota, Florida, were nebulized into a large outdoor photochemical chamber to mimic the atmospheric oxidation of aerosolized toxins and then aged in the presence or absence of sunlight and/or O₃. Aerosol samples were collected during the aging process using a Particle-Into-Liquid Sampler. Their BTx concentrations were measured using an enzyme-linked immuno-sorbent assay (ELISA) and high-performance liquid chromatography/tandem mass spectroscopy. The BTx ozonolysis rate constant measured by ELISA was 5.74 ± 0.21 × 10³ M^-1 s^-1. The corresponding lifetime for decay of 87.5% BTx in the presence of 20 ppb of O₃ was 7.08 ± 0.26 h, suggesting that aerosolized BTx can still travel long distances at night before SSA deposition. BTx concentrations in SSA decreased more rapidly in the presence of sunlight than in its absence due to oxidation with photochemically produced OH radicals.

Reducing Spread of Infections with a Photocatalytic Reactor-Potential Applications in Control of Hospital Staphylococcus aureus and Clostridioides difficile Infections and Inactivation of RNA Viruses

Contaminated surfaces and indoor environments are important sources of infectious spread within hospital and non-hospital facilities. Bacterial infections such as infections with Clostridioides (formerly Clostridium) difficile (C. difficile) and Staphylococcus aureus (S. aureus) and its antibiotic resistant strains continue to pose a significant risk to healthcare workers and patients. Additionally, the recent emergence of the coronavirus disease 2019 (COVID-19) pandemic, which is caused by the novel coronavirus, severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), highlights the need for safe and effective methods to decontaminate surfaces to control infection spread in hospitals and the community. To address these critical needs, we tested a photocatalytic reactor decontamination method to disinfect contaminated surfaces in a hospital and a laboratory setting. By placing the reactor in a test hospital room, growth of S. aureus and C. difficile were significantly reduced compared with a control room. Additionally, using a model enveloped positive-sense single-stranded RNA virus, dengue virus type 2 (DENV2), we showed that the use of the photocatalytic reactor reduces viral infectivity. Collectively, the results demonstrate the potential utility of photocatalytic reactors in reducing the spread of highly contagious bacterial and viral infections through contaminated surfaces and environments.

A kind of NiO nanofilm photocatalyst supported on nano-PAA substrate for efficient degradation of organic dye wastewater

Dye wastewater has been becoming the focus of environmental protection and scientific research because of its serious harm to the environment and living organisms. A supported nano-porous anode alumina-NiO (nano-PAA-NiO) photocatalyst was prepared by calcining nano-PAA-NiCl₂ composite which was grown with a self-organization method. Its morphology and composition were investigated by means of SEM, EDS, and XRD. The specific surface area of nano-PAA-NiO was characterized with the N₂ adsorption and desorption isotherms. The band gap was calculated to be 3.0 eV with the UV-Vis absorption spectra. The species and optical properties of nano-PAA-NiO were investigated by FT-IR spectra and photoluminescence spectra. With the nano-PAA-NiO photocatalyst, the degradation rates of methyl orange (MO) were 94.3% under the optimum conditions, and it could reach 82% when the catalyst was reused for the third time. In addition, the photocatalytic mechanism was proposed, and the reactions followed the Langmuir-Hinshelwood model. The nano-PAA-NiO composite has an excellent effect for organic dye wastewater treatment and practical prospects in environmental protection.

Degradation of okadaic acid in seawater by UV/TiO2 photocatalysis - Proof of concept

The consumption of contaminated shellfish with marine toxins causes adverse socioeconomical, environmental and health impacts. The marine toxin okadaic acid (OA) provokes diarrhetic shellfish poisoning (DSP) syndrome characterized by severe gastrointestinal symptoms. Therefore, there is increasing interest in removing these toxins from the marine environment to protect shellfish harvesting sites. Photocatalysis is proposed as an efficient method to detoxify the marine environment. In this study, Prorocentrum lima was used to produce high purity DSP toxins, in particular OA, for degradation studies. The profiling, characterization and quantification of DSP toxins in the culture of P. lima were achieved by ultrahigh performance liquid chromatography coupled to quadrupole-time of flight mass spectrometry (UPLC-QTOF-MSE) for accurate-mass full spectrum acquisition data. The effectiveness of UV/TiO2 system to degrade OA in seawater was assessed in lab-scale experiments and identification of transformation products was proposed based on the data obtained during analysis by UPLC-QTOF-MSE. The detoxification potential of the UV/TiO2 system was investigated using the phosphatase inhibition assay. Sufficient amount of high-purity OA (25 mg, >90% purity) was produced in-house for use in photocatalysis experiments by simple reversed-phase flash chromatography. Complete degradation of OA was observed in seawater after 30 min and 7.5 min in deionized water. The rate constants fitted with the pseudo-first order kinetic model (R2 > 0.96). High-resolution mass spectrometry analysis of the photocatalyzed OA allowed tentative identification of four transformation products. Detoxification was achieved in parallel with the degradation of OA in deionized water and artificial ocean water (≤20 min) but not for seawater. Overall, results suggest that UV/TiO2 photocatalysis can be an effective approach for degrading OA and their TPs in the marine environment. To the best of our knowledge, this is the first report on the use of photocatalysis to degrade marine toxins and its promising potential to protect shellfish harvesting sites.

Removal of microcystins from a waste stabilisation lagoon: Evaluation of a packed-bed continuous flow TiO2 reactor

Photocatalysis has been shown to successfully remove microcystins (MC) in laboratory experiments. Most research to date has been performed under ideal conditions in pure or ultrapure water. In this investigation the efficiency of photocatalysis using titanium dioxide was examined in a complex matrix (waste stabilisation lagoon water). A flow-through photocatalytic reactor was used for the photocatalytic removal of four commonly occurring microcystin analogues (MC-YR, MC-RR, MC-LR, and MC-LA). Up to 51% removal for single MC analogues in waste lagoon water was observed. Similar removal rates were observed when a mixture of all four MC analogues was treated. Although treatment of MC-containing cyanobacterial cells of Microcystis aeruginosa resulted in no decline in cell numbers or viability with the current reactor design and treatment regime, the photocatalytic treatment did improve the overall quality of waste lagoon water. This study demonstrates that despite the presence of natural organic matter the microcystins could be successfully degraded in a complex environmental matrix.

Introduction

The last 50 years have witnessed a growing awareness of the fragile state of most of the planets’ drinking water resources. Access to freshwater will become even more important in the near future, as the world’s population rises from 7 billion today to 9 billion by 2050. The World Health Organization (WHO) has estimated that 80 % of illnesses in the developing world are water related, resulting from poor water quality and lack of sanitation [1]. There are 3.3 million deaths each year from diarrheal diseases caused by bacteria such as Escherichia coli, Salmonella sp. and Cholera sp., parasites and viral pathogens. In the 1990s, the number of children who died of diarrhoea was greater than the sum of people killed in conflicts since World War II [2]. It is also estimated that around 4 billion people worldwide experience to have no or little access to clean and sanitized water supply, and millions of people died of severe waterborne diseases annually [3, 4].

Combined effect of UV-irradiation and TiO₂-nanoparticles on the predator-prey interaction of gammarids and mayfly nymphs

Although nanoparticle production and application increases continuously, their implications in species interactions, especially in combination with other environmental stressors, are rarely assessed. Therefore, the present study investigated the influence of 2 mg/L titanium dioxide nanoparticles (nTiO2; <100 nm) on the interaction between the prey Ephemerella ignita (Ephemeroptera) and the predator Gammarus fossarum (Amphipoda) over 96 h considering UV-irradiation at field relevant levels (approximately 11.4 W/m(2)) as an additional environmental factor (n = 16). At the same time, gammarid's consumption of an alternative food source, i.e. leaf discs, was assessed. All endpoints covered were not affected by nTiO2 alone, while the combination of nTiO2 and UV caused a reduction in gammarid's predation (68%), leaf consumption (60%) and body weight (22%). These effects were most likely triggered by the UV-induced formation of reactive oxygen species by nTiO2. The present study, hence, highlights the importance to cover UV-irradiation during the risk assessment of nanoparticles.

Green tide deactivation with layered-structure cuboids of Ag/CaTiO3 under UV light

In this work, an alternative to deactivate noxious green tide Tetraselmis suecica in the short-term is proposed by employing Perovskite-like cube-shaped, crystalline CaTiO3 semiconductors functionalized with atomic silver nanoparticles. CaTiO3 was prepared by a microwave-assisted hydrothermal method and then Ag(0)NPs (1 wt% of CaTiO3), were added by the photoreduction method. The XRD results show that crystalline CaTiO3 has an orthorhombic unit cell with a Perovskite-like structure. Images obtained by FESEM and HRTEM microscopies show well-faceted CaTiO3 rectangular prismatic morphology functionalizated with silver nanoparticles ≈ 13.5 nm. XPS and EDS-FESEM has confirmed the composition of CaTiO3 and silver occurring mainly as reduced metal. The UV inactivation of noxious T. suecica with Ag/CaTiO3 nanocomposites formed on bare materials results in complete deactivation of the algae in 12 min. The direct contact between harmful algae and Ag/CaTiO3 nanocomposite is necessary to deactivate the algae and inhibits algae viability.

Carbon-modified TiO2 for photocatalysis

Here we present a method to produce TiO2 nanocrystals coated by thin layer of graphitic carbon. The coating process was prepared via chemical vapor deposition (CVD) with acetylene used as a carbon feedstock with TiO2 used as a substrate. Different temperatures (400°C and 500°C) and times (10, 20, and 60 s) of reaction were explored. The prepared nanocomposites were investigated by means of transmission electron microscopy, Raman spectroscopy, thermogravimetric analysis, Fourier transform infrared spectroscopy/diffuse reflectance spectroscopy and ultraviolet-vis (UV-vis)/diffuse reflectance spectroscopy. Furthermore, photocatalytic activity of the materials was investigated under visible and UV-vis light irradiation in the process of phenol decomposition. It was found that TiO2 modification with carbon resulted in a significant increase of photoactivity under visible irradiation and decrease under UV-vis light irradiation. Interestingly, a shorter CVD time and higher process temperature resulted in the preparation of the samples exhibiting higher activity in the photocatalytic process under visible light irradiation.

Removal of microorganisms and their chemical metabolites from water using semiconductor photocatalysis

Semiconductor photocatalysis has been applied to the remediation of an extensive range of chemical pollutants in water over the past 30 years. The application of this versatile technology for removal of micro-organisms and cyanotoxins has recently become an area that has also been the subject of extensive research particularly over the past decade. This paper considers recent research in the application of semiconductor photocatalysis for the treatment of water contaminated with pathogenic micro-organisms and cyanotoxins. The basic processes involved in photocatalysis are described and examples of recent research into the use of photocatalysis for the removal of a range of microorganisms are detailed. The paper concludes with a review of the key research on the application of this process for the removal of chemical metabolites generated from cyanobacteria.

Titanium dioxide in our everyday life; is it safe?

BACKGROUND

Titanium dioxide (TiO(2)) is considered as an inert and safe material and has been used in many applications for decades. However, with the development of nanotechnologies TiO(2) nanoparticles, with numerous novel and useful properties, are increasingly manufactured and used. Therefore increased human and environmental exposure can be expected, which has put TiO(2) nanoparticles under toxicological scrutiny. Mechanistic toxicological studies show that TiO(2) nanoparticles predominantly cause adverse effects via induction of oxidative stress resulting in cell damage, genotoxicity, inflammation, immune response etc. The extent and type of damage strongly depends on physical and chemical characteristics of TiO(2) nanoparticles, which govern their bioavailability and reactivity. Based on the experimental evidence from animal inhalation studies TiO(2) nanoparticles are classified as "possible carcinogenic to humans" by the International Agency for Research on Cancer and as occupational carcinogen by the National Institute for Occupational Safety and Health. The studies on dermal exposure to TiO(2) nanoparticles, which is in humans substantial through the use of sunscreens, generally indicate negligible transdermal penetration; however data are needed on long-term exposure and potential adverse effects of photo-oxidation products. Although TiO(2) is permitted as an additive (E171) in food and pharmaceutical products we do not have reliable data on its absorption, distribution, excretion and toxicity on oral exposure. TiO(2) may also enter environment, and while it exerts low acute toxicity to aquatic organisms, upon long-term exposure it induces a range of sub-lethal effects.

CONCLUSIONS

Until relevant toxicological and human exposure data that would enable reliable risk assessment are obtained, TiO(2) nanoparticles should be used with great care.

Photocatalytic disinfection using titanium dioxide: spectrum and mechanism of antimicrobial activity

The photocatalytic properties of titanium dioxide are well known and have many applications including the removal of organic contaminants and production of self-cleaning glass. There is an increasing interest in the application of the photocatalytic properties of TiO(2) for disinfection of surfaces, air and water. Reviews of the applications of photocatalysis in disinfection (Gamage and Zhang 2010; Chong et al., Wat Res 44(10):2997-3027, 2010) and of modelling of TiO(2) action have recently been published (Dalrymple et al. , Appl Catal B 98(1-2):27-38, 2010). In this review, we give an overview of the effects of photoactivated TiO(2) on microorganisms. The activity has been shown to be capable of killing a wide range of Gram-negative and Gram-positive bacteria, filamentous and unicellular fungi, algae, protozoa, mammalian viruses and bacteriophage. Resting stages, particularly bacterial endospores, fungal spores and protozoan cysts, are generally more resistant than the vegetative forms, possibly due to the increased cell wall thickness. The killing mechanism involves degradation of the cell wall and cytoplasmic membrane due to the production of reactive oxygen species such as hydroxyl radicals and hydrogen peroxide. This initially leads to leakage of cellular contents then cell lysis and may be followed by complete mineralisation of the organism. Killing is most efficient when there is close contact between the organisms and the TiO(2) catalyst. The killing activity is enhanced by the presence of other antimicrobial agents such as Cu and Ag.