A review of environmental tobacco smoke and its determination in air

Face Mask as a Versatile Sampling Device for the Assessment of Personal Exposure to 54 Toxic Compounds in Environmental Tobacco Smoke

Exposure to environmental tobacco smoke (ETS), which contains hundreds of toxic compounds, significantly increases the risk of developing many human diseases, including lung cancer. The most common method of assessing personal exposure to ETS-borne toxicants is by sampling sidestream smoke generated by a smoking machine through a sorbent tube or filter, followed by solvent extraction and instrumental analysis. However, the ETS sampled may not truly represent the ETS in the ambient environment, due to complicating factors from the smoke released by the burning end of the cigarette and from the absorption of the chemicals in the respiratory tract of the smoker. In this study, we developed and validated an alternative air sampling method involving breathing through a face mask to simultaneously determine personal exposure to 54 ETS-borne compounds, including polycyclic aromatic hydrocarbons, aromatic amines, alkaloids, and phenolic compounds in real smoking scenarios. The newly developed method was used to evaluate the risk associated with exposure to ETS released from conventional cigarettes (CCs) and that from novel tobacco products such as e-cigarettes (ECs) and heated tobacco products (HTPs), with the observation of cancer risk associated with exposure to ETS released from CCs significantly higher than that from ECs and HTPs. It is anticipated that this method offers a convenient and sensitive way to collect samples for assessing the health impacts of ETS exposure.

Indexes of tobacco smoke contribution to environmental particulates based on molecular fingerprints of alkanes

Tobacco smoke (TS) is the source of a number of toxicants affecting the atmosphere and poses a threat to smokers and the whole community. Chemical, physical, and toxicological features of smoking products (vapors as well as mainstream, side stream, and third-hand smoke) have been investigated extensively. Special attention is paid to organic compounds (individually or in combination giving rise to peculiar molecular fingerprints), potentially able to act as "chemical signature" of TS. In this regard, the percent distribution of long-chainnormal, iso, and anteiso alkanes was ascertained as typical of TS. Nevertheless, until now no indexes have been identified as suitable for assessing the global TS contribution to environmental pollution, e.g., the TS percentage in carbonaceous aerosol and in deposited dusts, the only exception consisting in the use of nicotelline as tracer. This paper describes the results of an extensive study aimed at chemically characterizing the nonpolar lipid fraction associated to suspended particulates (PMs) and deposition dusts (DDs) collected at indoor and outdoor locations. Based on the iso, anteiso, and normal C₂₉-C₃₄ alkane profile in the samples as well in tobacco smoke- and no-TS-related emissions (literature data), various parameters describing the distribution of compounds were investigated. Finally, a cumulative variable was identified as the tobacco smoke impact index (TS%) suitable for estimating the TS percentage occurring in the particulate matter. The TS% rates were plotted vs. the exceedance of normal C₃₁ alkane with respect to the average of C₂₉ and C₃₃ homologs, which results higher in TS than in most other emissions, revealing a link in the case of suspended particulates but not of deposited dusts. According to back analysis carried out on all particulate matter sets, it was found that traces of TS affect even remote areas, while inside the smokers' homes the contributions of TS to PM could account for up to ~61% and ~10%, respectively, in PM and DD. This confirms the need of valuing the health risk posed by TS to humans, by means of tools easy to apply in extensive investigations.

Analytical Approaches and Trends in the Determination of Psychoactive Drugs in Air

Understanding of the levels of psychoactive drugs in air is important for assessing both occupational and environmental exposure. Intelligence on the usage and manufacture of illegal drugs can also be gained. Environmental analysis and determination of air quality has recently expanded from its traditional focus to new pollutant categories that include illicit and psychoactive drugs. This is attributed to a greater part on the development of new, advanced techniques, such as liquid chromatography/mass spectrometry (LC/MS), allowing for the trace determination of such compounds down to the parts-per-trillion (ng/L) levels generally reported in air. Studies have also investigated the effects of firsthand and secondhand smoking of drugs, such as cocaine, cannabis and opium. Generally, these have shown secondhand smoke effects to be limited, apart from in the case of opium. Some studies have highlighted ill effects resulting through the exposure of vapors and dusts from the storage of drugs, but this has been shown to result from mould and other fungal contaminates. Investigations into the possible occupational exposures resulting from the use of anesthetic drugs in surgery and accident and emergency have focused on nitrous oxide, sevoflurane, methoxyflurane, isoflurane, propofol and fentanyl. This review focuses on developments and applications for the determination of psychoactive drugs in air.

Portable dehumidifiers condensed water: A novel matrix for the screening of semi-volatile compounds in indoor air

The comprehensive identification of organic species existing in indoor environments is a key issue to understand their impact in human health. This study proposes the analysis of condensed water samples, collected with portable dehumidifiers, to characterize semi-volatile compounds in the gas phase of confined areas. Water samples are concentrated by solid-phase extraction (SPE). The obtained extracts are analysed by gas chromatography (GC) time-of-flight mass spectrometry (TOF-MS), following a non-target screening data mining approach. In first term, spectra of deconvoluted compounds are compared with those in NIST low resolution library; thereafter, tentative identifications are verified using an in-house database of accurate electron ionization (EI) MS spectra. Chromatographic (retention index) and spectral data are combined for unambiguous species identification. The potential of condensed water samples to reflect changes in the composition of indoor atmospheres, the match between data obtained using different dehumidifiers, and the relative concentration efficiency of condensed water compared to that attained by active sampling of moderate air volumes are discussed. A total of 141 semi-volatile compounds were identified (98 confirmed against authentic standards) in a set of 21 samples obtained from different homes and working places. This list contains more than 40 fragrances (including several potential allergens), solvents and intermediates in the production of polymeric materials, plasticizers and flame retardants.

A Wearable IoT Aldehyde Sensor for Pediatric Asthma Research and Management

A cloud-based wearable IoT aldehyde sensor system for asthma research and management.

Study of the mainstream cigarette smoke aerosols by Fourier transform ion cyclotron resonance mass spectrometry coupled to laser/desorption and electrospray ionization - Additional insights on the heteroaromatic components

RATIONALE

The chemical composition of the particulate phase of cigarette smoke inhaled by the active smoker is still poorly known in spite of its importance from a health point of view. A non-targeted approach is applied to cigarette smoke particles collected on a quartz filter to obtain an as complete as possible description of this complex mixture.

METHODS

A home-made smoking machine including devices for volatile organic compounds (VOCs) and particle sampling was used. The validation of the cigarette smoking and cigarette smoke collection procedures was conducted by the quantification of some compounds by gas chromatography/mass spectrometry (GC/MS). The particles were investigated by Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) directly after their collection on quartz filters by laser/desorption ionization (LDI) or after extraction with CH2 Cl2 by electrospray ionization (ESI).

RESULTS

The determination of the benzene, toluene, ethylbenzene and xylenes (from 2 to 35 μg/cigarette) and nicotine (0.68 ± 0.05 mg/cigarette) validated the used sampling method. The complementarity of the LDI and ESI sources for the cigarette smoke analysis was established. The ESI analyses evidenced polar compounds and components with a pyridine group and LDI ensured the detection of poly-condensed heteroaromatic species. Finally, this methodology was employed to characterize particles from cigarettes with or without flavoring additives.

CONCLUSIONS

Some insights into the composition of cigarette smoke inhaled by active smokers have been obtained. The ~1750 observed features revealed the huge complexity of cigarette smoke particles and the diversity of the possible associated health issues. Both heteroaromatic and highly oxygenated compounds produced by combustion and pyrolysis have been highlighted.

Detection of Cigarette Smoke Using a Surface-Acoustic-Wave Gas Sensor with Non-Polymer-Based Oxidized Hollow Mesoporous Carbon Nanospheres

The objective of this research was to develop a surface-acoustic-wave (SAW) sensor of cigarette smoke to prevent tobacco hazards and to detect cigarette smoke in real time through the adsorption of an ambient tobacco marker. The SAW sensor was coated with oxidized hollow mesoporous carbon nanospheres (O-HMC) as a sensing material of a new type, which replaced a polymer. O-HMC were fabricated using nitric acid to form carboxyl groups on carbon frameworks. The modified conditions of O-HMC were analyzed with Scanning Electron Microscopy (SEM), Fourier transform infrared spectrometry (FTIR), and X-ray diffraction (XRD). The appropriately modified O-HMC are more sensitive than polyacrylic acid and hollow mesoporous carbon nanospheres (PAA-HMC), which is proven by normalization. This increases the sensitivity of a standard tobacco marker (3-ethenylpyridine, 3-EP) from 37.8 to 51.2 Hz/ppm and prevents the drawbacks of a polymer-based sensing material. On filtering particles above 1 μm and using tar to prevent tar adhesion, the SAW sensor detects cigarette smoke with sufficient sensitivity and satisfactory repeatability. Tests, showing satisfactory selectivity to the cigarette smoke marker (3-EP) with interfering gases CH₄, CO, and CO₂, show that CO and CO₂ have a negligible role during the detection of cigarette smoke.

Detection of third-hand smoke on clothing fibers with a surface acoustic wave gas sensor

Third-hand smoke (THS) is a new cigarette-related issue defined as the residual contamination from cigarette smoke after a cigarette is extinguished. To detect THS on three commonly used clothing fibers-wool, cotton, and polyester, we applied two methods to measure the adsorption of THS: one was the gain of mass with an analytical balance after exposure to cigarette smoke; and the other was to detect the THS chemical compounds such as nicotine and 3-ethenylpyridine with a surface acoustic wave (SAW) sensor composed of coated oxidized hollow mesoporous carbon nanospheres. In the mass measurement, the gain of mass decreased in the order wool, cotton, and polyester; the latter gain was about one tenth that of wool. In the SAW detection, the frequency shift decreased in the same order-wool, cotton, and polyester. The residence period of THS on natural fiber (wool and cotton) is greater than on synthetic polyester fiber. These two tests provide quantitative results of THS on varied clothing fibers, to assess their risk after exposure to cigarette smoke.

A rapid method for the chromatographic analysis of volatile organic compounds in exhaled breath of tobacco cigarette and electronic cigarette smokers

A method for the rapid analysis of volatile organic compounds (VOCs) in smoke from tobacco and electronic cigarettes and in exhaled breath of users of these smoking systems has been developed. Both disposable and rechargeable e-cigarettes were considered. Smoke or breath were collected in Bio-VOCs. VOCs were then desorbed in Tenax cartridges which were subsequently analyzed by thermal desorption coupled to gas chromatography-mass spectrometry. The method provides consistent results when comparing the VOC compositions from cigarette smoke and the equivalent exhaled breath of the smokers. The differences in composition of these two sample types are useful to ascertain which compounds are retained in the respiratory system after tobacco cigarette or e-cigarette smoking. Strong differences were observed in the VOC composition of tobacco cigarette smoke and exhaled breath when comparing with those of e-cigarette smoking. The former involved transfers of a much larger burden of organic compounds into smokers, including benzene, toluene, naphthalene and other pollutants of general concern. e-Cigarettes led to strong absorptions of propylene glycol and glycerin in the users of these systems. Tobacco cigarettes were also those showing highest concentration differences between nicotine concentrations in smoke and exhaled breath. The results from disposable e-cigarettes were very similar to those from rechargeable e-cigarettes.

New Look at BTEX: Are Ambient Levels a Problem?

Benzene, toluene, ethylbenzene, and xylene (BTEX) are retrieved during fossil fuel extraction and used as solvents in consumer and industrial products, as gasoline additives, and as intermediates in the synthesis of organic compounds for many consumer products. Emissions from the combustion of gasoline and diesel fuels are the largest contributors to atmospheric BTEX concentrations. However, levels indoors (where people spend greater than 83% of their time) can be many times greater than outdoors. In this review we identified epidemiological studies assessing the noncancer health impacts of ambient level BTEX exposure (i.e., nonoccupational) and discussed how the health conditions may be hormonally mediated. Health effects significantly associated with ambient level exposure included sperm abnormalities, reduced fetal growth, cardiovascular disease, respiratory dysfunction, asthma, sensitization to common antigens, and more. Several hormones including estrogens, androgens, glucocorticoids, insulin, and serotonin may be involved in these health outcomes. This analysis suggests that all four chemicals may have endocrine disrupting properties at exposure levels below reference concentrations (i.e., safe levels) issued by the U.S. Environmental Protection Agency. These data should be considered when evaluating the use of BTEX in consumer and industrial products and indicates a need to change how chemicals present at low concentrations are assessed and regulated.

Comparison between the mainstream smoke of eleven RYO tobacco brands and the reference tobacco 3R4F

In this study 11 commercial roll-your-own (RYO) tobacco brands sold in Spain and the reference tobacco 3R4F have been smoked and several components of the mainstream tobacco smoke have been analyzed. Cigarettes were prepared using commercial tubes, and were smoked under smoking conditions based on the ISO 3308. The gaseous and condensed fractions of the smoke from RYO brands and 3R4F have been analyzed and compared. RYO tobaccos, as opposed to 3R4F, present lower amounts of condensed products in the traps than in the filters. In general, RYO tobaccos also provide lower yields of most of the compounds detected in the gas fraction. The yield of CO is between 15.4 and 20.4 mg/cigarette. In most of the cases studied, RYO tobaccos deliver higher amounts of nicotine than the 3R4F tobacco. On average, the yield of the different chemical families of compounds appearing in the particulate matter retained in the cigarette filters tends to be around three times higher than those obtained from 3R4F, whereas similar values have been obtained in the particulate matter retained in the traps located after the filters. It can be concluded that RYO tobaccos are not less hazardous than the reference tobacco, which may be contrary to popular belief.

Personal exposure of primary school children to BTEX, NO₂ and ozone in Eskişehir, Turkey: relationship with indoor/outdoor concentrations and risk assessment

Personal exposures of 65 primary school children to benzene, toluene, ethyl benzene, xylenes (BTEX), nitrogen dioxide (NO2) and ozone (O3) were measured during 24h by using organic vapor monitors and tailor-made passive samplers. Two schools were selected to represent students living in more polluted (urban) and less polluted (sub-urban) areas in the city of Eskişehir, Turkey. The pollutant concentrations were also measured in indoor and outdoor environments during the personal sampling to investigate the contribution of each micro-environment on measured personal concentrations. Socio-demographic and personal time-activity data were collected by means of questionnaires and half-hour-time resolution activity diaries. Personal exposure concentrations were found to be correlated with indoor home concentrations. Personal, indoor and outdoor concentrations of all studied pollutants except for ozone were found to be higher for the students living at the urban traffic site. Ozone, on the other hand, had higher concentrations at the sub-urban site for all three types of measurements (personal, indoor and outdoor). Analysis of the questionnaire data pointed out to environmental tobacco smoke, use of solvent based products, and petrol station nearby as factors that affect personal exposure concentrations. Cancer and non-cancer risks were estimated using the personal exposure concentrations. The mean cancer risk for the urban school children (1.7×10(-5)) was found to be higher than the sub-urban school children (0.88×10(-5)). Children living with smoking parents had higher risk levels (1.7×10(-5)) than children living with non-smoking parents (1.08×10(-5)). Overall, the risk levels were <1×10(-4). All hazard quotient values for BTEX for the non-cancer health effects were <1 based on the calculations EPA's Risk Assessment Guidance for Superfund (RAGS) part F.

Thirdhand smoke and exposure in California hotels: non-smoking rooms fail to protect non-smoking hotel guests from tobacco smoke exposure

INTRODUCTION

This study examined tobacco smoke pollution (also known as thirdhand smoke, THS) in hotels with and without complete smoking bans and investigated whether non-smoking guests staying overnight in these hotels were exposed to tobacco smoke pollutants.

METHODS

A stratified random sample of hotels with (n=10) and without (n=30) complete smoking bans was examined. Surfaces and air were analysed for tobacco smoke pollutants (ie, nicotine and 3-ethynylpyridine, 3EP). Non-smoking confederates who stayed overnight in guestrooms provided urine and finger wipe samples to determine exposure to nicotine and the tobacco-specific carcinogen 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone as measured by their metabolites cotinine and 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol (NNAL), respectively.

FINDINGS

Compared with hotels with complete smoking bans, surface nicotine and air 3EP were elevated in non-smoking and smoking rooms of hotels that allowed smoking. Air nicotine levels in smoking rooms were significantly higher than those in non-smoking rooms of hotels with and without complete smoking bans. Hallway surfaces outside of smoking rooms also showed higher levels of nicotine than those outside of non-smoking rooms. Non-smoking confederates staying in hotels without complete smoking bans showed higher levels of finger nicotine and urine cotinine than those staying in hotels with complete smoking bans. Confederates showed significant elevations in urinary NNAL after staying in the 10 most polluted rooms.

CONCLUSIONS

Partial smoking bans in hotels do not protect non-smoking guests from exposure to tobacco smoke and tobacco-specific carcinogens. Non-smokers are advised to stay in hotels with complete smoking bans. Existing policies exempting hotels from complete smoking bans are ineffective.

Analysis of the volatile components emitted from cut tobacco processing by gas chromatography/mass spectrometry thermal desorption system

A sensitive and reliable method was developed for the determination of volatile components emitted from cut tobacco processing using thermal desorption (TD) followed by gas chromatography-mass spectrometry (GC-MS). In the work, to obtain the optimal sorbent, three commercial sorbents were compared in terms of adsorption efficiency. The carbotrap 349 was found to have the best performance. The desorption conditions were also studied. Validation of the TD-GC-MS method showed good sensibility, linearity and precision. Limits of detection ranges were from 0.20 to 3.6 ng. Calibration curves were obtained by plotting peak area versus concentration and the correlation coefficients relating to linearity were at least 0.9984. The analysis was reproducible, with relative standard deviation (n=8) within 6.5%. The target compound breakthrough examination showed no significant losses when about 1500 ng standards were prepared. In order to evaluate the performance of the analytical method in the volatile constituents of cut tobacco, samples were taken in industrial areas of cut tobacco processing. Recoveries ranged from 85.1% to 110% for all the compounds and good precision had been reached (RSD<13.3). The results proved that TD-GC-MS was a simple, rapid and accurate method for the analysis of volatile compounds emitted from cut tobacco drying step.

Determination of the volatiles from tobacco by capillary gas chromatography with atomic emission detection and mass spectrometry

A new gas chromatograph-atomic emission detector (GC-AED) coupled with Deans switching technique for analyzing volatiles from tobaccos were developed. The detector operating parameters (reagent gas pressure and make-up gas flow rate) were optimized. The detection limits for the elements carbon (193 nm), hydrogen (486 nm) and oxygen (171 nm) ranged 0.05-0.2, 0.05-0.3 and 1-11 ng, respectively, depending on the compound. The sensitivity and linearity for the elements carbon (193 nm), hydrogen (486 nm) and oxygen (171 nm) decreased in the order O>H>C. Calibration curves were obtained by plotting peak area versus concentration, and the correlation coefficients relating to linearity were at least 0.9359. Elemental response factors measured on these channels, relative to the carbon 193-nm channel, were hydrogen, 0.38-0.48 (mean %RSD=5.64), and oxygen, 0.085-0.128 (mean %RSD=14.9). The evaluation was also done for the new technique and for an established GC-MS technique for the same real samples. The results of GC-AED and GC-MS showed that there was a relatively good agreement between the two sets of data.

Volatile organics off-gassed among tobacco-exposed clothing fabrics

This work evaluates the characteristics of short-term release of volatile and semi-volatile organic chemicals from clothing fabrics that are exposed to environmental tobacco smoke (ETS). Various fabrics were concurrently exposed to ETS in a controlled facility, and the chemicals off-gassed were sampled using solid phase micro-extraction coupled with GC/MS analysis. Toluene-reference concentration (TRC) was calculated for nine selected chemicals and compared. The number of chemicals identified from ETS-exposed fabrics ranged from 13 (polyester and acetate) to 32 (linen). All fabrics off-gassed formaldehyde, tetradecanoic acid and n-hexadecanoic acid, while seven out of eight fabrics emitted furfural, benzonitrile, naphthalene and decanal. Natural fibers of plant origin (cotton and linen) off-gassed higher concentrations (TRC>100 μg/l) of chemicals that have low molecular weight (~100 or less) than did natural fibers of animal origin (wool and silk) and synthetic fibers. Conversely, wool and silk off-gassed more chemicals that are of high molecular weight (>200), such as TDA (TRC>100 μg/l) and n-HDA (TRC>500 μg/l), than did other fabrics. Fabric structure (for a particular material) significantly affects chemical off-gassing. Cotton typically used for polo shirt (knitted) off-gassed significantly (p<0.05) higher TRC for chemicals with molecular weight of ~100 (such as furfural) than did other cottons of woven style. The dyeing of fabric (white vs. black) had a limited effect on emission, while increasing contact time with ETS increased the intensity of chemical emissions. The mean TRC for cotton exposed for 12 min was nearly doubled than those exposed for 8min, but no difference existed for polyester.