Molecularly-imprinted monoliths for sample treatment and separation

Chiral metal-organic frameworks grown in situ for monolithic capillary electrochromatographic enantioseparation

Chiral metal-organic frameworks (CMOFs) with chiral selectivity are one of the high-quality stationary phases for capillary electrochromatography (CEC). However, there is a problem of unsatisfactory enantioseparation performance of capillary columns due to insufficient loading. In this work, a lamellar CMOF (Cu-TC) was grown in situ on the surface of the monolith in a capillary monolithic column to obtain a Cu-TC@monolithic column. The CEC system constructed based on the Cu-TC@monolithic column shows a satisfactory chiral separation performance. Compared with the Cu-TC-based coated column (Cu-TC@coated column), the enantioseparation performance of the CEC system based on the Cu-TC@monolithic column was greatly improved, and the resolutions (Rs) of the model analytes were increased by 80-500%. In addition, the effects of experimental conditions such as the number of cycles of Cu-TC in situ growth, buffer concentration, buffer pH, organic solvent addition and applied voltage on the performance of CEC were also investigated. Finally, the chiral selection mechanism of the stationary phase was explored by selective adsorption experiments. The present work provides a new idea for the development of capillary stationary phases, which has great potential considering the diversity of CMOFs.

Highly selective molecularly imprinted polymer nanoparticles (MIP NPs)-based microfluidic gas sensor for tetrahydrocannabinol (THC) detection

A highly selective microfluidic integrated metal oxide gas sensor for THC detection is reported based on MIP nanoparticles (MIP NPs). We synthesized MIP NPs with THC recognition sites and coated them on a 3D-printed microfluidic channel surface. The sensitivity and selectivity of coated microfluidic integrated gas sensors were evaluated by exposure to THC, cannabidiol (CBD), methanol, and ethanol analytes in 300-700 ppm at 300 °C. For comparison, reference signals were obtained from a microfluidic channel coated with nonimprinted polymers (NIP NPs). The MIP and NIP NPs were characterized using scanning electron microscopy (SEM) and Raman spectroscopy. MIP and NIP NPs channels response data were combined and classified with 96.3% accuracy using the Fine KNN classification model in MATLAB R2021b Classification Learner App. Compared to the MIP NPs coated channel, the NIP NPs channel had poor selectivity towards THC, demonstrating that the THC recognition sites in the MIP structure enabled selective detection of THC. The findings demonstrated that the recognition sites of MIP NPs properly captured THC molecules, enabling the selective detection of THC compared to CBD, methanol, and ethanol.

Bioinspired polydopamine-mediated metal-organic framework click-grafting aptamers functionalized fabric for highly-specific recognition of microcystin-leucine arginine

Fabricating functional electrospun nanofiber coating for highly selective extraction of microcystin-LR (MC-LR) was of significant importance for water-safety monitoring. Herein, a novel MOF@aptamer functionalized nanofabric was presented via a facile and reliable strategy integrating polydopamine (PDA) mediation and thiol-ene chemistry and applied for specific recognition of the MC-LR model analyte. Using polydopamine (PDA) as the mediating layer, vinyl-UiO-66 MOF was grown in situ, followed by post-synthetic modification (PSM) of Zr⁴⁺ with vinyl phosphate and rapid UV-initiated click reaction of aptamers. Uniform deposition of Zr-based MOF (vinyl-UiO-66) on the nanofibers was directly produced, and the tedious co-electrospinning process was abandoned to prevent the aggregation and encapsulation of MOF. Via an efficient "thiol-ene" chemistry, massive thiol-terminated aptamers were grafted on MOF within one step under friendly conditions, rather than the time-consuming nanoparticle adsorption or unfriendly covalent chemical reactions. As a result, the robust MOF@aptamer-coated nano-fabrics were obtained, and a highly selective performance towards MC-LR was illustrated with a limit of detection (LOD) at 0.002 ng/mL, good precision (CV<8.3%), good repeatability (2.2∼6.0%) when coupled with LC-MS. Almost 1∼2 orders of magnitude higher detection sensitivity was exhibited than that of the common non-specific SPE/SPME fiber reported so far. Applied to water samples, the good matrix-resistance ability, and acceptable recovery yields were achieved with high specificity. This strategy might provide a rapid and friendly protocol to efficiently fabricate MOF@aptamer functionalized nano-fabrics through electrospinning and interfacial "thiol-ene" chemistry for highly-selective microextraction.

Investigation of Thermodynamic, Kinetic, and Isothermal Parameters for the Selective Adsorption of Bisphenol A

Herein, a novel imprinted solid-phase extraction cartridge was fabricated to investigate the kinetic, thermodynamic, and isothermal parameters for the selective adsorption of Bisphenol A (BPA). The imprinted polymeric cartridges (BMC) for the BPA adsorption were fabricated in the presence of a template and functional monomer using the in situ polymerization technique. To prove the efficiency and selectivity of BMC, the nonimprinted polymeric cartridges (BNC) and the empty polymeric cartridges (EC) were also fabricated with and without functional monomer using the same manner for the preparation of BMC. The characterization of cartridges was performed by elemental analysis, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) surface area measurements, and swelling tests. BPA removal studies were performed by analyzing some parameters such as temperature, BPA concentration, flow rate, salt type, and concentration. The highest capacity was determined as 103.2 mg BPA/g polymer for a 0.75 mL/min flow rate of 0.75 M (NH₄)₂SO₄ containing 200 mg/L BPA solution at 50 °C. NaOH (1.0 M) was used as a desorption agent. The reusability performance was examined by performing 10 consecutive cycles. The solid-phase extraction (SPE) performance was also checked to determine the enrichment and extraction recovery factors for tap water and synthetic wastewater samples. Temkin, Langmuir, Freundlich, and Dubinin-Radushkevich isotherm models were applied to BPA adsorption data examining the adsorption mechanism, surface properties, and adsorption degree. The most suitable isotherm model for BPA adsorption was determined as the Langmuir isotherm model. The thermodynamic parameters (ΔG°, ΔH°, and ΔS°) were investigated to reveal the thermodynamics of adsorption. Adsorption thermodynamic parameters (ΔH°, ΔS°, and ΔG°) were calculated using the thermodynamic equilibrium constant (thermodynamic equilibrium constant, K°) values that change with temperature. It was determined that BPA adsorption was spontaneous (ΔG° < 0) and endothermic (ΔH° > 0) and entropy increased (ΔS° > 0) at the temperatures studied in the BPA adsorption process. The rate control step in the adsorption process was examined by applying pseudo-first-order and pseudo-second-order kinetic models to the adsorption data for the investigations of BPA adsorption kinetics, and the pseudo-second-order kinetic model was found to be more suitable for describing BPA adsorption kinetics. In examining the selectivity of cartridges, structural analogues of hydroquinone, phenol, β-estradiol, and 8-hydroxyquinoline were tested.

Recent advances and applications of molecularly imprinted polymers in solid-phase extraction for real sample analysis

Sample pretreatment is essential for the analysis of complicated real samples due to their complex matrices and low analyte concentrations. Among all sample pretreatment methods, solid-phase extraction is arguably the most frequently used one. However, the majority of available solid-phase extraction adsorbents suffer from limited selectivity. Molecularly imprinted polymers are a type of tailor-made artificial antibodies and receptors with specific recognition sites for target molecules. Using molecularly imprinted polymers instead of conventional adsorbents can greatly improve the selectivity of solid-phase extraction, and therefore molecularly imprinted polymer-based solid-phase extraction has been widely applied to separation, clean up and/or preconcentration of target analytes in various kinds of real samples. In this article, after a brief introduction, the recent developments and applications of molecularly imprinted polymer-based solid-phase extraction for determination of different analytes in complicated real samples during the 2015-2020 are reviewed systematically, including the solid-phase extraction modes, molecularly imprinted adsorbent types and their preparations, and the practical applications of solid-phase extraction to various real samples (environmental, food, biological, and pharmaceutical samples). Finally, the challenges and opportunities of using molecularly imprinted polymer-based solid-phase extraction for real sample analysis are discussed.

Molecularly Imprinted Polymer Micro- and Nano-Particles. A review

In recent years, molecularly imprinted polymers (MIPs) have become an excellent solution to the selective and sensitive determination of target molecules in complex matrices where other similar and relative structural compounds could coexist. Although MIPs show the inherent properties of the polymers, including stability, robustness, and easy/cheap synthesis, some of their characteristics can be enhanced, or new functionalities can be obtained when nanoparticles are incorporated in their polymeric structure. The great variety of nanoparticles available significantly increase the possibility of finding the adequate design of nanostructured MIP for each analytical problem. Moreover, different structures (i.e., monolithic solids or MIPs micro/nanoparticles) can be produced depending on the used synthesis approach. This review aims to summarize and describe the most recent and innovative strategies since 2015, based on the combination of MIPs with nanoparticles. The role of the nanoparticles in the polymerization, as well as in the imprinting and adsorption efficiency, is also discussed through the review.

Epitope Imprinting Technology: Progress, Applications, and Perspectives toward Artificial Antibodies

Epitope imprinting is a promising tool to generate antibody-like specific recognition sites. Recently, because of the ease of obtaining templates, the flexibility in selecting monomers, their resistance to harsh environments, and the high specificity toward targets, epitope-imprinted materials have attracted much attention in various fields, such as bioanalysis, clinical therapy, and pharmacy. Here, the discussion is focused on the current representative epitope imprinting technologies, including epitope bulk imprinting and epitope surface imprinting. Moreover, the application of epitope-imprinted materials to the recognition of peptides, proteins, and cells is reviewed. Finally, the remaining challenges arising from the intrinsic properties of epitope imprinting are discussed, and future development in the field is prospected.

Novel coordination imprinted polymer monolithic column applied to the solid-phase extraction of flumequine from fish samples

In this study, a coordination imprinted polymer (CIP) solid-phase extraction (SPE) method was developed to determine the residues of flumequine (FLU) in fish samples. Silanized graphene oxide-doped CIP (SGO-CIP) monolithic column was prepared using FLU-Zn²⁺ as template in the presence of SGO. The synthesis conditions of SGO-CIP column were optimized by the response surface methodology. Under the optimum conditions, this column showed high specificity to FLU, and the adsorption capacity reached 61.74 ng mg^-1. The enrichment factor of the monolithic column was over 40-fold. Various factors affecting the extraction efficiency of SGO-CIP column during SPE were tested to achieve optimal enrichment and to reduce non-specific adsorption. FLU in fish was detected by using a high-performance liquid chromatography-fluorescence detection system. The detection limit was as low as 0.32 ng g^-1 and the recovery was as high as 95.2%, with relative standard deviations of below 5.9%. This simple and sensitive method may be applicable to the determination of FLU residues in foods.

Synthesis and characterization of a surface-grafted Pb(ii)-imprinted polymer based on activated carbon for selective separation and pre-concentration of Pb(ii) ions from environmental water samples

Even the lowest concentration level of lead (Pb) in the human body is dangerous to health due to its bioaccumulation and high toxicity.

Preparation of Imazethapyr Surface Molecularly Imprinted Polymers for Its Selective Recognition of Imazethapyr in Soil Samples

A novel strategy based on imazethapyr (IM) molecular-imprinting polymers (MIPs) grafted onto the surface of chloromethylation polystyrene resin via surface-initiated atom transfer radical polymerization (SI-ATRP) for specific recognition and sensitive determination of trace imazethapyr in soil samples was developed. The SI-ATRP was performed by using methanol-water (4 : 1, v/v) as the solvent, acrylamide as the functional monomer, trimethylolpropane trimethacrylate (TRIM) as the cross-linker, imazethapyr as the template, and CuBr/2,2'-bipyridine as the catalyst. The resulting MIPs were characterized by elemental analysis, Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Then, the binding selectivity, adsorption capacity, and reusability of the MIPs were evaluated. The results indicated that the prepared MIPs exhibited specific recognition and high selectivity for imazethapyr. The MIPs were further used as solid-phase extraction (SPE) materials coupled with high-performance liquid chromatography (HPLC) for selective extraction and detection of trace imazethapyr from soil samples. The results showed that good linearity was observed in the range of 0.10-5.00 μg/mL, with a correlation coefficient of 0.9995. The limit of detection (LOD) of this method was 15 ng/g, and the extraction recoveries of imazethapyr from real samples were in the range of 91.1-97.5%, which proved applicable for analysis of trace imazethapyr in soils. This work proposed a sensitive, rapid, and convenient approach for determination of trace imazethapyr in soil samples.

Advancements of molecularly imprinted polymers in the food safety field

Molecularly imprinted technology (MIT) has been widely employed to produce stable, robust and cheap molecularly imprinted polymer (MIP) materials that possess selective binding sites for recognition of target analytes in food, such as pesticides, veterinary drugs, mycotoxins, illegal drugs and so on. Because of high selectivity and specificity, MIPs have drawn great attention in the food safety field. In this review, the recent developments of MIPs in various applications for food safety, including sample preparation, chromatographic separation, sensing, immunoassay etc., have been summarized. We particularly discuss the advancements and limitations in these applications, as well as attempts carried out for their improvement.

Evaluation of porogen factors for the preparation of ion imprinted polymer monoliths used in mercury removal

In the present study, ion imprinted polymer monoliths (IIPMs) were developed to overcome the limitations of ion imprinted polymer particles (IIPPs) used for the removal of Hg(II) ions from waste water samples. The adsorbents preparation, characterization and Hg(II) removal were very well reported. The IIPMs on porogen optimization was prepared using the molding technique with Hg(II) as a template ion, [2-(methacryloyloxy)ethyl]trimethylammonium cysteine (MAETC) as ligand, methacrylic acid (MAA) as functional monomer, ethylene glycol dimethacrylamide (EGDMA) as cross-linker, benzoyl peroxide as an initiator and methanol and acetonitrile as porogen in the polypropylene tube (drinking straw) as mold. The IIPMs prepared with higher volumes of porogen were indicated to have a good adsorption rate for the Hg(II) removal along with good water permeability and larger porosity as compared to a lower volume of porogen. The IIPMs prepared using the binary porogen were able to improve the porosity and surface area of the monolithic polymers as compared to the single porogen added IIPMs. Finally, we indicate from our analysis that the IIPM having the efficient capacity for the Hg(II) ions is easy to prepare, and has higher water permeability along with high porosity and high adsorption capacity and all these factors making it one of the suitable adsorbent for the successful removal of Hg(II) ions.

Cholesterol-imprinted macroporous monoliths: Preparation and characterization

The development of sorbents for selective binding of cholesterol, which is a risk factor for cardiovascular disease, has a great importance for analytical science and medicine. In this work, two series of macroporous cholesterol-imprinted monolithic sorbents differing in the composition of functional monomers (methacrylic acid, butyl methacrylate, 2-hydroxyethyl methacrylate and ethylene dimethacrylate), amount of a template (4, 6 and 8 mol%) used for molecular imprinting, as well as mean pore size were synthesized by in situ free-radical process in stainless steel housing of 50 mm × 4.6 mm i.d. All prepared materials were characterized regarding to their hydrodynamic permeability and porous properties, as well as examined by BET and SEM methods. Imprinting factors, apparent dynamic dissociation constants, the maximum binding capacity, the number of theoretical plates and the height equivalent to a theoretical palate of MIP monoliths at different mobile phase flow rates were determined. The separation of a mixture of structural analogues, namely, cholesterol and prednisolone, was demonstrated. Additionally, the possibility of using the developed monoliths for cholesterol solid-phase extraction from simulated biological solution was shown.

Extraction, Analytical and Advanced Methods for Detection of Allura Red AC (E129) in Food and Beverages Products

Allura Red AC (E129) is an azo dye that widely used in drinks, juices, bakery, meat, and sweets products. High consumption of Allura Red has claimed an adverse effects of human health including allergies, food intolerance, cancer, multiple sclerosis, attention deficit hyperactivity disorder, brain damage, nausea, cardiac disease and asthma due to the reaction of aromatic azo compounds (R = R′ = aromatic). Several countries have banned and strictly controlled the uses of Allura Red in food and beverage products. This review paper is critically summarized on the available analytical and advanced methods for determination of Allura Red and also concisely discussed on the acceptable daily intake, toxicology and extraction methods.

Preparation and characterization of biocompatible molecularly imprinted poly(ionic liquid) films on the surface of multi-walled carbon nanotubes

A series of novel biocompatible MIPs were synthesized for BSA recognition by using MWCNTs with different outside diameters as substrates, and allyl-functionalized ionic liquids with different anion species as monomers.

Molecular imprinting: perspectives and applications

This critical review presents a survey of recent developments in technologies and strategies for the preparation of MIPs, followed by the application of MIPs in sample pretreatment, chromatographic separation and chemical sensing.

Colorimetric sensing of melamine using colloidal magnetically assembled molecularly imprinted photonic crystals

A colorimetric colloidal MIPC sensor was constructed by the magnetic assembly of MMIP colloids, it could directly transmit the stimuli from the adsorption of MEL into visually perceptible optical signals.

Preparation and characterization of macroporous monoliths imprinted with erythromycin

The synthesis of macroporous molecularly imprinted monoliths was performed using the monomers system 2-hydroxyethyl methacrylate-ethylene glycol dimethacrylate and erythromycin as a template. The copolymerization was carried out in situ inside 50 mm × 4.6 mm i.d. stainless-steel tubing. The morphology of the monoliths was examined with scanning electron microscopy. The porous characteristics were determined both from the data of hydrodynamic permeability of monoliths and by means of mercury intrusion porosimetry. The retention parameters of target substance (erythromycin), values of calculated imprinting factors and apparent dynamic dissociation constants were obtained for monoliths prepared with the application of different amount of template (4, 8 and 12 mol%). The separations of the mixtures azithromycin/erythromycin and ciprofloxacin/erythromycin were demonstrated. Additionally, the possibility of erythromycin quantification in human blood plasma was shown.

Synthesis of magnetic molecularly imprinted polymers by reversible addition fragmentation chain transfer strategy and its application in the Sudan dyes residue analysis

Magnetic molecularly imprinted polymers (MMIPs) have become a hotspot owing to the dual functions of target recognition and magnetic separation. In this study, the MMIPs were obtained by the surface-initiated reversible addition fragmentation chain transfer (RAFT) polymerization using Sudan I as the template. The resultant MMIPs were characterized by transmission electron microscope, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, vibrating sample magnetometer, and X-ray diffraction. Benefiting from the controlled/living property of the RAFT strategy, the uniform MIP layer was successfully grafted on the surface of RAFT agent-modified Fe3O4@SiO2 nanoparticles, favoring the fast mass transfer and rapid binding kinetics. The developed MMIPs were used as the solid-phase extraction sorbents to selectively extract four Sudan dyes (Sudan I, II, III, and IV) from chili powder samples. The recoveries of the spiked samples in chili powder samples ranged from 74.1 to 93.3% with RSD lower than 6.4% and the relative standard uncertainty lower than 0.029. This work provided a good platform for the extraction and removal of Sudan dyes in complicated matrixes and demonstrated a bright future for the application of the well-constructed MMIPs in the field of solid-phase extraction.

Synthesis and application of surface-imprinted activated carbon sorbent for solid-phase extraction and determination of copper (II)

A new Cu(II)-imprinted amino-functionalized activated carbon sorbent was prepared by a surface imprinting technique for selective solid-phase extraction (SPE) of Cu(II) prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Experimental conditions for effective adsorption of Cu(II) were optimized with respect to different experimental parameters using static and dynamic procedures in detail. Compared with non-imprinted sorbent, the ion-imprinted sorbent had higher selectivity and adsorption capacity for Cu(II). The maximum static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Cu(II) was 26.71 and 6.86 mg g(-1), respectively. The relatively selectivity factor values (αr) of Cu(II)/Zn(II), Cu(II)/Ni(II), Cu(II)/Co(II) and Cu(II)/Pb(II) were 166.16, 50.77, 72.26 and 175.77, respectively, which were greater than 1. Complete elution of the adsorbed Cu(II) from Cu(II)-imprinted sorbent was carried out using 2 mL of 0.1 mol L(-1) EDTA solution. The relative standard deviation of the method was 2.4% for eleven replicate determinations. The method was validated for the analysis by two certified reference materials (GBW 08301, GBW 08303), the results obtained is in good agreement with standard values. The developed method was also successfully applied to the determination of trace copper in natural water samples with satisfactory results.