Analytical challenges and advantages of using flow-based methodologies for ammonia determination in estuarine and marine waters

1-(o-Tolyl)thiourea-based deep eutectic solvent as a stationary phase in flow injection analysis system for mercury and copper determination in edible oils

In this work, a novel deep eutectic solvent (DES) composed of thymol and 1-(o Tolyl)thiourea 9/1 (mol) is presented for the first time. This DES has not been described in the literature. This DES was first used as a stationary phase in an extraction column integrated into a flow injection analysis system for the simultaneous determination of mercury and copper in edible oils. The automated approach involves passing an aqueous sample solution obtained after microwave mineralization through a microcolumn of DES retained on polytetrafluoroethylene. This leading to the extraction and concentration of the analytes. The metals are then eluted with an aqueous thiourea solution for subsequent analysis by inductively coupled plasma-optical emission spectrometry. The limits of detection (LODs) for mercury and copper were 3 μg L⁻1 and 2.5 μg L⁻1, respectively. The approach demonstrated high accuracy. Relative standard deviations (RSD) for repeatability and inter-day reproducibility ranged from 3 % to 11 %. Extraction recovery of both metals exceeded 95 %, indicating the high efficiency of the DES-based extraction process. Environmental assessment using the AGREEprep method yielded a favorable environmental index of 0.54, highlighting the robustness of the approach. This novel use of DES as a stationary phase in flow injection analysis system provides a robust, efficient and environmentally friendly approach to the determination of trace metals in edible oils. This method can also be applied to the analysis of other samples.

Electrocatalysts for Inorganic and Organic Waste Nitrogen Conversion

Anthropogenic activities have disrupted the natural nitrogen cycle, increasing the level of nitrogen contaminants in water. Nitrogen contaminants are harmful to humans and the environment. This motivates research on advanced and decarbonized treatment technologies that are capable of removing or valorizing nitrogen waste found in water. In this context, the electrocatalytic conversion of inorganic- and organic-based nitrogen compounds has emerged as an important approach that is capable of upconverting waste nitrogen into valuable compounds. This approach differs from state-of-the-art wastewater treatment, which primarily converts inorganic nitrogen to dinitrogen, and organic nitrogen is sent to landfills. Here, we review recent efforts related to electrocatalytic conversion of inorganic- and organic-based nitrogen waste. Specifically, we detail the role that electrocatalyst design (alloys, defects, morphology, and faceting) plays in the promotion of high-activity and high-selectivity electrocatalysts. We also discuss the impact of wastewater constituents. Finally, we discuss the critical product analyses required to ensure that the reported performance is accurate.

Development and Characterization of a Sol-Gel-Functionalized Glass Carbon Electrode Probe for Sensing Ultra-Trace Amounts of NH3 and NH4+ in Water

This study centers on the development and characterization of an innovative electrochemical sensing probe composed of a sensing mesoporous functional sol-gel coating integrated onto a glassy carbon electrode (sol-gel/GCE) for the detection of NH3 and/or NH4+ in water. The main interest for integrating a functional sol-gel coating onto a GCE is to increase the selective and sensing properties of the GCE probe towards NH3 and/or NH4+ ions. The structure and surface morphology of the newly developed sol-gel/GCE probe were characterized employing scanning electron microscopy (SEM), atomic force microscopy (AFM), dynamic light scattering (DLS), and Fourier-transform infrared (FTIR), while the electrochemical sensing properties were evaluated by Berthelot's reaction, cyclic voltammetry (CV), and adsorptive square wave-anodic striping voltammetry (Ads SW-ASV). It is shown that the newly developed sol-gel coating is homogeneously deposited on the GCE with a sub-micron and uniform thickness close to 630 nm and a surface roughness of 25 nm. The sensing testing of the sol-gel/GCE probe showed limits of detection and limits of quantitation of 1.7 and 5.56 nM of NH4+, respectively, as well as a probe sensitivity of 5.74 × 10-1 μA/μM cm-2. The developed probe was fruitfully validated for the selective detection of NH3/NH4+ in fresh and sea water samples. Computed Student texp (0.45-1.25) and Fexp (1.69-1.78) (n = 5) tests were less than the theoretical ttab (2.78) and Ftab (6.39) at 95% probability.

Measurements and analysis of nitrogen and phosphorus in oceans: Practice, frontiers, and insights

Nitrogen and phosphorus concentrations in oceans have been extensively studied, and advancements in associated disciplines have rapidly progressed, enabling the exploration of novel and previously challenging questions. A keyword analysis was conducted using the Scopus database to examine chronological trends and hotspots, offering comprehensive insights into the evolution of marine nitrogen and phosphorus research. For this purpose, author keyword networks were developed for the periods before 1990, 1990 to 2000, 2001 to 2011, and 2012 to 2022. Furthermore, analytical techniques employed in the recent decade to determine nitrogen and phosphorus concentrations in seawater were assessed for their applicability and limitations through a critical review of more than 50 journal articles. Taxonomy and nitrogen biogeochemistry were the prominent research interests for the first two periods, respectively, while stable isotopic tracking of nitrogen and phosphorus processes emerged as the dominant research focus for the last two decades. The integration of macroeconomic factors in research development and the chronological rise of interdisciplinary research were identified. Conventional analytical techniques such as spectrophotometry, colorimetry, fluorometry, and elemental analysis were noted, along with emerging techniques like remote sensing and microfluidic sensors.

Portable Conductometric Sensing Probe for Real-Time Monitoring Ammonia Profile in Coastal Waters

An ability to real-time and continuously monitor ammonium/ammonia profiles of coastal waters over a prolonged period in a simple and maintenance-free fashion would enable economic conducting large-scale assessments, providing the needed scientific insights to better control and mitigate the impact of eutrophication on coastal ecosystems. However, this is a challenging task due to the lack of capable sensors. Here, we demonstrate the use of a membrane-based conductometric ammonia sensing probe (CASP) for real-time monitoring of ammonia levels in coastal waters. A boric acid/glycerol receiving phase is investigated and innovatively utilized to overcome the high salinity of coastal water-induced analytical errors. A calibration-free approach is used to eliminate the need for ongoing calibration, while the issues concerning practical applications, such as salinity variation, ammonia intake capability, and biofouling, are systematically investigated. The field deployment at an estuary confluence water site over a half-moon cycle period confirms that CASP is capable of continuously monitoring the ammonia profile of coastal waters in real-time with high resolution and accuracy to unveil the dynamic ammonia concentration changes over a prolonged period.

Real-time underway measurement of ammonium in coastal and estuarine waters using an automated flow analyzer with hollow fiber membrane contactor

Ammonium (NH₄⁺) is an important parameter for aquatic ecosystems. To date, continuous and underway acquisition of NH₄⁺ in coastal and estuarine waters has been challenged by the strongly varying salinity and complex matrices in these waters. To address these issues, a hollow fiber membrane contactor (HFMC) was constructed and incorporated in flow injection analysis (FIA) to achieve online separation/preconcentration of NH₄⁺ in water. In the FIA-HFMC system, NH₄⁺ in the water sample was converted into NH₃ under alkaline conditions in the donor channel. The generated NH₃ diffused across the membrane and was absorbed in an acid solution in the acceptor channel. The resultant NH₄⁺ in the acceptor was then quantified based on a modified indophenol blue (IPB) method. Parameters affecting the performance of the FIA-HFMC-IPB system were evaluated and optimized. Under the optimized conditions, the proposed system exhibited a limit of detection of 0.11 μmol L^-1, with relative standard deviations of 1.0-1.9 % (n = 7), and a good linear response (R² = 0.9989) for the calibration in the field with NH₄⁺ standards in the range of 0.40-80 μmol L^-1. The proposed system was applied to a shipboard underway measurement of NH₄⁺ in a two-day cruise in the Jiulong River Estuary-Xiamen Bay, China. A good agreement was observed between measurements from the proposed system and those from manual sampling and laboratory analysis. Both laboratory and field results demonstrated that the system was free of salinity effect and interference from organic nitrogen compounds. The system also showed excellent stability and reliability during a 16-day observation. This work suggests that the proposed FIA-HFMC-IPB system is applicable for the underway measurement of NH₄⁺ in water, especially for estuarine and coastal waters with varying salinity and complex matrices.

Ammonium determination by merging-zone flow injection analysis and a naphthalene-based fluorescent probe

This paper discusses the first-time study of a naphthalene-based fluorescent probe-naphthalene-2,3-dicarboxaldehyde (NDA), in combination with merging-zone flow injection analysis for the automated fluorescence determination of ammonium. The determination was contingent on detecting the fluorescent product of NDA-SO₃^2--NH₄⁺, which has maximum excitation and emission wavelengths of 508 nm and 564 nm, respectively. And the possible sensing mechanism of NDA-NH₄⁺ was proposed. The effects of the reaction parameters, including reagent concentrations, reaction flow rate, coil length, reaction temperature, and pH were optimized. Under optimal conditions, this method afforded a sampling rate of 8 h^-1, a limit of detection of 0.045 μmol L^-1, and RSD of 3.68% (n = 14) with 1.50 μmol L^-1 ammonium, and the calibration range was 0.045-6.00 μmol L^-1. Examination of the organic nitrogen interference confirmed that the method attracts minimal interference from organic nitrogen, and the stability of the NDA reagent facilitates its field application. Other exhibited advantages include low reagent consumption and high automation; the method has been utilized in the successful determination of ammonium in freshwater and rainwater. The development of NDA applications for ammonium determination also provides more options for fluorometric determination of ammonium.

Portable determinations for legislated dissolved nitrogen forms in several environmental water samples as a study case

In this work, we have studied the main species involved in determining total dissolved nitrogen (TDN) in water samples for accommodating a variety of quantitation methodologies to portable instruments and with the goal to achieve in situ analysis. The rise of water eutrophication is becoming an ecological problem in the world and TDN contributes markedly to this. Traditionally the several forms of DN are measured in the laboratory using conventional instrumentation from grab samples, but their analysis in place and in real time is a current demand. Inorganic nitrogen: NO₃^-, NO₂^- and NH₄⁺, and organic nitrogen, such as amino nitrogen were tested here. For nitrate that presents native UV absorption suitable for direct water analysis, a portable optical fiber probe was compared with benchtop equipment and an in place analyzer. For nitrate, nitrite and ammonium, in situ solid devices that deliver reagents needed were tested and water color was measured by a smartphone coupled with a miniaturized optical fiber spectrometer and a miniaturized spectrometer or from images obtained and their RGB components. Amino nitrogen of some aromatic aminoacids with native fluorescence was followed by a portable optical fiber probe. Organic amino nitrogen and ammonium were determined by a portable luminometer and luminol supported in a measurement tube. Moreover, a portable miniaturized liquid chromatograph was shown suitable for monitoring priority nitrogen environmental pollutants. All options provided suitable results in comparison with lab estimations and were useful for evaluating if the legislation is fulfilled for the variety of tested waters. A discussion about the several portable options proposed for in place analysis, in function of the legislated determinations needed for each type of water was carried out.

A Critical Review on Chemical Speciation of Chlorine-Produced Oxidants (CPOs) in Seawater. Part 2: Sampling, Sample Preparation and Non-Chromatographic and Mass Spectrometric-Based Methods

Chlorination of seawater forms a range of secondary oxidative species, collectively termed "chlorine-produced oxidants" (CPOs). These compounds do not have the same biocidal efficacy, the same fate and behavior in the marine environment, the same potential formation of chlorination by-products (CBPs), nor the same effects on marine organisms. Their chemical speciation is an important step toward an accurate assessment of the effectiveness of chlorination and the potential impacts of its releases, among others. The aim of this paper - which is the second of a trilogy dedicated to the chemical speciation of CPOs in seawater - is to cover all aspects related to CPOs analysis in seawater, from sampling to instrumental determination. First, it discusses the procedures involved in synthesis, storage, and standardization of analytical standards. Second, it deals with sampling and sample preparation, addressing all relevant issues related to these two key steps. Third, it provides a comprehensive and up-to-date overview of the colorimetric, titrimetric, and electrochemical methods used for CPOs determination and thoroughly discusses their advantages and limitations. Finally, this review ends with some recommendations for progress in the field of CPO analysis with the three aforementioned approaches. Chromatographic and mass spectrometric-based methods will be covered in the third and final article (Part III).

Real-Time Underway Mapping of Nutrient Concentrations of Surface Seawater Using an Autonomous Flow Analyzer

High-frequency field nutrient analyzers offer a promising technology to solve time-consuming and laborious sampling problems in dynamic and complex river-estuarine-coastal ecosystems. However, few studies on the simultaneous underway analysis of five key nutrients (ammonium, nitrite, nitrate, phosphate, and silicate) in seawaters are available because of the limitations of the technique. In this study, a state-of-the-art autonomous portable analyzer for the shipboard analysis of nutrients in the environment of varied salinities and concentration ranges was reported. The analyzer consisted of compact hardware that was well suited for shipboard deployment with minimal maintenance. Moreover, a novel LabVIEW-based software program was developed, containing additional functions such as automated calibration curve generation, autodilution of high-concentration samples, and a user-friendly interface for multiparameter analysis using a single instrument. After the optimization of chemical reactions and work flow chart, the analyzer exhibited low limits of detection, a large linear range with automated dilution, and relative standard deviations of less than 2% (n = 11). Compared to other flow-based techniques, this analyzer is more portable and consumes less reagent with an autonomous data processing function and applicability within a broad salinity range (0-35). The analyzer was successfully applied for real-time analysis in the Jiulong River Estuary-Xiamen Bay with excellent on-site accuracy and applicability. The relationship between high spatial resolution nutrient concentrations and salinities showed very different patterns in estuarine and coastal areas, indicating the benefit of using an underway automated analyzer for chemical mapping in a dynamic environment.

Flow-Injection Methods in Water Analysis-Recent Developments

Widespread demand for the analysis and control of water quality and supply for human activity and ecosystem sustainability has necessitated the continuous improvement of water analysis methods in terms of their reliability, efficiency, and costs. To satisfy these requirements, flow-injection analysis using different detection methods has successfully been developed in recent decades. This review, based on about 100 original research papers, presents the achievements in this field over the past ten years. Various methodologies for establishing flow-injection measurements are reviewed, together with microfluidics and portable systems. The developed applications mostly concern not only the determination of inorganic analytes but also the speciation analysis of different elements, and the determination of several total indices of water quality. Examples of the determination of organic residues (e.g., pesticides, phenolic compounds, and surfactants) in natural surface waters, seawater, groundwater, and drinking water have also been identified. Usually, changes in the format of manual procedures for flow-injection determination results in the improvement of various operational parameters, such as the limits of detection, the sampling rate, or selectivity in different matrices.

Determination of ammonium and biogenic amines by ion chromatography. A review

The amount and type of chemical compounds found in food products and the environment, which are and should be controlled, is increasing. This is associated with toxicological knowledge, resulting regulations, rapid development of analytical methods and techniques, and sample preparation methods for analysis. These include, among others, ammonia derivatives such as ammonium, and amines, including biogenic amines. Their occurrence in the environment and food is related to their widespread use in many areas of life and their formation as a result of various physical and chemical changes. Analysts use various methods both classical and instrumental to theirs quantify in different matrices such as food, medicinal and environmental samples. Nevertheless, there is still a need for analytical methods with increased matrix-tolerance, selectivity, specificity, and higher sensitivity. While in the determination of ammonium, ion chromatography is a reference method. In the case of biogenic amines, its use for these purposes is not yet so common. However, given ion chromatography its advantages and rapid development, its importance can be expected to increase in the near future, especially at the expense of gas chromatography methods. This paper is a summary of the advantages and limitations of ion chromatography in this important analytical field and a literature review of the past 15 years.

Response of water quality to land use in hydrologic response unit and riparian buffer along the Dan River, China

Land uses determine water quality within riparian environments to a certain extent and directly affect human health via drinking water. The main objective of this paper is to investigate the influences of land use, both in hydrologic response units (HRUs) and 200-m-wide buffer areas, on surface water quality. The variations and interrelationships between water physicochemical properties and land uses were assessed for better management of water environment. Nitrogen was the dominant nutrient and was significantly correlated with other water quality parameters. In the HRUs and buffer areas, the dominant landscape was grassland and farmland, respectively. Total organic carbon (TOC) and dissolved oxygen (DO) had negative correlation with land use factors; nitrate nitrogen, total nitrogen, total phosphorus, electrical conductivity, and temperature, in contrast, were positively correlated with them. Industrial and residential land was the critical land use for the aquatic environment in the Dan River, indicating that point pollution should receive more attention. Vegetation area had strong regression relationships with TOC and DO. Furthermore, more specific types of land use (subcategory classification) had a greater role in water quality. The land use in buffers can act on the water body more directly and effectively.

An environmentally-benign flow-batch system for headspace single-drop microextraction and on-drop conductometric detecting ammonium

This work presents a lab-made automatic flow-batch system for headspace single-drop microextraction and on-drop conductometric sensing ammonium. Sample and NaOH solution are simultaneously pumped into a reaction chamber (RC), where ammonium is converted to ammonia by raising pH. The converted ammonia then diffuses into the headspace of the RC, and reacts with a 100 mM boric acid drop. The conductivity of the drop is measured by an on-drop conductivity probe, which is made by two stainless-steel contacting electrodes. The result shows that the increasing rate of conductivity has a linear relationship to the ammonium concentration in sample (R² = 0.9945). This method has a linear range up to 400 μM, a limit of detection 2.8 μM, a relative standard deviation of 3.0% (200 μM, n = 10) and carryover coefficient 0.028. Measurements of river waters, lake waters and wastewaters have been demonstrated. The recoveries have achieved from 99.0 to 114%. This method avoids using of harmful or odorous reagents and follows the concept of green chemistry.

Monitoring of ammonia in marine waters using a passive sampler with biofouling resistance and neural network-based calibration

A biofouling resistant passive sampler for ammonia, where the semi-permeable barrier is a microporous hydrophobic gas-diffusion membrane, has been developed for the first time and successfully applied to determine the time-weighted average concentration of ammonia in estuarine and coastal waters for 7 days. Strategies to control biofouling of the membrane were investigated by covering it with either a copper mesh or a silver nanoparticle functionalised cotton mesh, with the former approach showing better performance. The effects of temperature, pH and salinity on the accumulation of ammonia in the newly developed passive sampler were studied and the first two parameters were found to influence it significantly. A universal calibration model for the passive sampler was developed using the Group Method Data Handling algorithm based on seawater samples spiked with known concentrations of total ammonia under conditions ranging from 10 to 30 °C, pH 7.8 to 8.2 and salinity 20 to 35. The newly developed passive sampler is affordable, user-friendly, reusable, sensitive, and can be used to detect concentrations lower than the recently proposed guideline value of 160 μg total NH₃-N L^-1, for a 99% species protection level, with the lowest concentration measured at 17 nM molecular NH₃ (i.e., 8 μg total NH₃-N L^-1 at pH 8.0 and 20 °C). It was deployed at four field sites in the coastal waters of Nerm (Port Phillip Bay), Victoria, Australia. Good agreement was found between molecular ammonia concentrations obtained with passive and discrete grab sampling methods (relative difference, - 12% to - 19%).

Study of interferences and procedures for their removal in the spectrophotometric determination of ammonium and selected anions in coloured wastewater samples

Ammonium and selected anions were determined in wastewater samples with highly complex matrices by spectrophotometry using the reagent-kit method. For this purpose, the interferents of coloured compounds and S^2-, SO₃^2-, CO₃^2- and Cl^-, which are often present in wastewater samples, were systematically investigated in the spectrophotometric determination of ammonium, nitrate, chloride, sulphate, fluoride and phosphate. After this, innovative procedures for their removal were proposed. For sample decolourization, a DEAE column was used to determine ammonium, while a Florisil column was used for the colour removal and anions' determination. S^2- and CO₃^2- were eliminated from the samples by adding HCl or HNO₃, which transformed them into gases H₂S and CO₂. The stepwise addition of CaCl₂ to the sample, adjusted to pH 8, initiated the formation of CaSO₃, which was removed by filtration. Cl^- was removed by the addition of Ag₂O, which formed a AgCl precipitate that was removed from the solution by filtration. The accuracy of the determination was tested with spike-recovery tests, which showed recoveries for the analytes in the spiked samples ranging from 95 to 105%. The repeatability of the measurements of nitrate, chloride, sulphate and phosphate in the wastewater samples was better than ±1%, while that for the ammonium and fluoride samples was ±2 and ±5%, respectively. The data from the present investigation revealed that the developed procedures for the decolourization and stepwise removal of interferents enabled accurate spectrophotometric determination of ammonium, nitrate, chloride, sulphate, fluoride and phosphate by using cuvette tests in complex wastewater and environmental water samples.

Micro-PAD card for measuring total ammonia nitrogen in saliva

This work presents a portable microfluidic paper-based analytical device (micro-PAD) card for the quantification of total ammonia nitrogen in human saliva. The amount of total ammonia nitrogen in saliva can be an indicator of the status of the oral microbiome with potential correlation to kidney health problems. The developed micro-PAD card comprises twenty units consisting of three stacked layers of circular discs: the sample layer, paper discs impregnated with sodium hydroxide solution, the PTFE membrane layer, and the detection layer, paper discs impregnated with bromothymol blue. The twenty units were aligned on transparent laminating pouches laminated to form the micro-PAD card (7.5 cm × 10.5 cm). Saliva samples can be directly dispensed onto the micro-PAD card and the detection was achieved by the BTB indicator color change, from yellow to blue, after conversion of ammonium into ammonia and diffusion of the ammonia gas through a hydrophobic layer. The determination of total ammonia nitrogen in saliva using the developed micro-PAD card intended to be very simple method and operated without the need of laboratory equipment. A quantification limit of 11.3 NH₄⁺mg L^-1 and linear application range from up to 150 NH₄⁺mg L^-1 were obtained making it suitable for the expected concentrations of total ammonia nitrogen in human saliva. It was successfully applied to saliva samples and its validation obtained by comparison against a potentiometric method. The card is stable for at least 1 month making it ideal as a portable device for point-of-care diagnosis. Graphical Abstract.

Automatic On-Line Purge-and-Trap Sequential Injection Analysis for Trace Ammonium Determination in Untreated Estuarine and Seawater Samples

An innovative automatic purge-and-trap (P&T) system coupled with fluorimetric sequential injection (SI), for the on-line separation and preconcentration of volatile compounds, is presented. The truth of concept is demonstrated for the ammonium fluorimetric determination in environmental water samples with complex matrices without any pretreatment. The P&T flow system comprises a thermostated purge-vessel where ammonium is converted into gaseous ammonia and a trap-vessel for ammonia collection. This configuration results in matrix removal as well as analyte preconcentration, avoiding membrane-associated problems. All the main parameters affecting the efficiency of a P&T system were studied and optimized. The proposed method is characterized by a working range of 2.7–150.0 μg L⁻¹ of NH₄⁺, with a detection and quantification limit of 0.80 and 2.66 μg L⁻¹, respectively, for a 10-mL sample consumption. The accuracy of the method was assessed by recovery assays in seawater, estuarine, and lake water samples as well as by the analysis of standard reference material.

Advances in sensing ammonia from agricultural sources

Reducing ammonia emissions is one of the most difficult challenges for environmental regulators around the world. About 90% of ammonia in the atmosphere comes from agricultural sources, so that improving farm practices in order to reduce these emissions is a priority. Airborne ammonia is the key precursor for particulate matter (PM2.5) that impairs human health, and ammonia can contribute to excess nitrogen that causes eutrophication in water and biodiversity loss in plant ecosystems. Reductions in excess nitrogen (N) from ammonia are needed so that farms use N resources more efficiently and avoid unnecessary costs. To support the adoption of ammonia emission mitigation practices, new sensor developments are required to identify sources, individual contributions, to evaluate the effectiveness of controls, to monitor progress towards emission-reduction targets, and to develop incentives for behavioural change. There is specifically a need for sensitive, selective, robust and user-friendly sensors to monitor ammonia from livestock production and fertiliser application. Most currently-available sensors need specialists to set up, calibrate and maintain them, which creates issues with staffing and costs when monitoring large areas or when there is a need for high frequency sampling. This paper reports advances in monitoring airborne ammonia in agricultural areas. Selecting the right method of monitoring for each agricultural activity will provide critical data to identify and implement appropriate ammonia controls. Recent developments in chemo-resistive materials allow electrochemical sensing at room temperature, and new spectroscopic methods are sensitive enough to determine low concentrations in the order of parts per billion. However, these new methods still compromise selectivity and sensitivity due to the presence of ambient dust and other interferences, and are not yet suitable to be applied in agricultural monitoring. This review considers how ammonia measurements are made and applied, including the need for sensors that are suitable for routine monitoring by non-specialists. The review evaluates how monitoring information can be used for policies and regulations to mitigate ammonia emissions. The increasing concerns about ammonia emissions and the particular needs from the agriculture sector are addressed, giving an overview of the state-of-the-art and an outlook on future developments.

Nitrate measurement in droplet flow: gas-mediated crosstalk and correction

In droplet microfluidics, droplets have traditionally been considered discrete self-contained reaction chambers, however recent work has shown that dissolved solutes can transfer into the oil phase and migrate into neighbouring droplets under certain conditions. The majority of reports on such inter-droplet "crosstalk" have focused on surfactant-driven mechanisms, such as transport within micelles. While trialling a droplet-based system for quantifying nitrate in water, we encountered crosstalk driven by a very different mechanism: conversion of the analyte to a gaseous intermediate which subsequently diffused between droplets. Importantly we found that the crosstalk occurred predictably, could be experimentally quantified, and measurements rationally post-corrected. This showed that droplet microfluidic systems susceptible to crosstalk such as this can nonetheless be used for quantitative analysis.

Automatic pressure-assisted dual-headspace gas-liquid microextraction. Lab-in-syringe platform for membraneless gas separation of ammonia coupled with fluorimetric sequential injection analysis

A novel pressure-assisted dual-headspace lab-in-syringe microextraction technique is presented as an alternative approach for automatic on-line membraneless gas separation of volatile compounds. The developed gas-liquid microextraction procedure is based on the lab-in-syringe (LIS) concept by using two independent micro-syringe pumps which are connected to each other for the application of negative and positive pressure inside the common headspace area of the syringe barrels. The adoption of reduced and increased pressure conditions is facilitated by the programmable LIS strategy resulting in increased extraction rates. The analytical process includes the in-situ ammonia vapor generation in the headspace of the first microsyringe, under reduced pressure environment, and its subsequent transportation into the headspace of the second microsyringe. Then, positive pressure is applied inside the second microsyringe enabling the ammonia vapor dissolution into the extraction solution to produce a fluorescent product (isoindol-1-sulfonat). The reaction is time and temperature affected, thus after an optimized time of delay inside the thermostated syringe barrel at 60 °C, it is delivered into the flow-cell of the miniSIA system where it is quantified at 425 nm (excitation wavelength, 365 nm). The proposed preconcentration system has been fully tested and optimized regarding the relevant parameters affecting the generation of gaseous ammonia, its effective transportation into the headspace of the second syringe barrel and its quantitative dissolution and reaction with the extraction solution. For a sample volume of 3000 μL, the sample frequency is 8 h^-1, the precision expressed as relative standard deviation (RSD) is 3.6 (at 5.0 μg L^-1) and a detection limit (3s) of 0.05 μg L^-1 for ammonium is obtained. The detection is linear in the concentration range of 0.15 and 10.0 μg L^-1 with a correlation coefficient of 0.9987. The accuracy of the proposed method has been evaluated by analyzing a standard reference material (relative error: 3.8%) as well as using the Certified Method (relative error < 5.5%) for ammonium determination. The potential of this novel schema has been demonstrated for ammonia determination in natural water samples.

Development of an Integrated Syringe-Pump-Based Environmental-Water Analyzer ( iSEA) and Application of It for Fully Automated Real-Time Determination of Ammonium in Fresh Water

The development of a multipurpose integrated syringe-pump-based environmental-water analyzer ( iSEA) and its application for spectrophotometric determination of ammonium is presented. The iSEA consists of a mini-syringe pump equipped with a selection valve and laboratory-programmed software written by LabVIEW. The chemistry is based on a modified indophenol method using o-phenylphenol. The effect of reagent concentrations and sample temperatures was evaluated. This fully automated analyzer had a detection limit of 0.12 μM with sample throughput of 12 h^-1. Relative standard deviations at different concentrations (0-20 μM) were 0.23-3.36% ( n = 3-11) and 1.0% ( n = 144, in 24 h of continuous measurement, ∼5 μM). Calibration curves were linear ( R² = 0.9998) over the range of 0-20 and 0-70 μM for the detection at 700 and 600 nm, respectively. The iSEA was applied in continuous real-time monitoring of ammonium variations in a river for 24 h and 14 days. A total of 1802 samples were measured, and only 0.4% was outlier data (≥3 sigma residuals). Measurements of reference materials and different aqueous samples ( n = 26) showed no significant difference between results obtained by reference and present methods. The system is compact (18 cm × 22 cm × 24 cm), portable (4.8 kg), and robust (high-resolution real-time monitoring in harsh environments) and consumes a small amount of chemicals (20-30 μL/run) and sample/standards (2.9 mL/run).

Simultaneous determination of total dissolved nitrogen and total dissolved phosphorus in natural waters with an on-line UV and thermal digestion

A flow injection method combined with an on-line UV and thermal digestion for simultaneous determination of total dissolved nitrogen (TDN) and total dissolved phosphorus (TDP) in natural waters was established in this study. A novel flow manifold made the proposed system compact and automatic. The conversion rates of various nitrogen and phosphorus compounds to their nitrate and phosphate forms with different digestion models and different concentrations were well investigated using the flow injection technique. The reagent concentrations for colorimetric analysis were optimized based on a univariate experimental design. The detection limits were 0.8 μmol L^-1 and 0.2 μmol L^-1, and linear analytical ranges were up to 300 μmol L^-1 and 25 μmol L^-1 for TDN and TDP, respectively. The sample throughput was ~ 5 h^-1. The recovery of spiked natural water samples varied from 86.8% to 102.6% for TDN and 88.0% to 102.0% for TDP. The present approach was successfully applied for the determination of TDN and TDP in natural water samples and was found to have good agreement with reference methods. The outcomes of present study indicated that the proposed method is suitable for routine analysis as well as for potential on-line monitoring.

Miniaturizing and automation of free acidity measurements for uranium (VI)-HNO3 solutions: Development of a new sequential injection analysis for a sustainable radio-analytical chemistry

A miniaturized and automated approach for the determination of free acidity in solutions containing uranium (VI) is presented. The measurement technique is based on the concept of sequential injection analysis with on-line spectroscopic detection. The proposed methodology relies on the complexation and alkalimetric titration of nitric acid using a pH 5.6 sodium oxalate solution. The titration process is followed by UV/VIS detection at 650nm thanks to addition of Congo red as universal pH indicator. Mixing sequence as well as method validity was investigated by numerical simulation. This new analytical design allows fast (2.3min), reliable and accurate free acidity determination of low volume samples (10µL) containing uranium/[H(+)] moles ratio of 1:3 with relative standard deviation of <7.0% (n=11). The linearity range of the free nitric acid measurement is excellent up to 2.77molL(-1) with a correlation coefficient (R(2)) of 0.995. The method is specific, presence of actinide ions up to 0.54molL(-1) does not interfere on the determination of free nitric acid. In addition to automation, the developed sequential injection analysis method greatly improves the standard off-line oxalate complexation and alkalimetric titration method by reducing thousand fold the required sample volume, forty times the nuclear waste per analysis as well as the analysis time by eight fold. These analytical parameters are important especially in nuclear-related applications to improve laboratory safety, personnel exposure to radioactive samples and to drastically reduce environmental impacts or analytical radioactive waste.

Monitoring variations of dimethyl sulfide and dimethylsulfoniopropionate in seawater and the atmosphere based on sequential vapor generation and ion molecule reaction mass spectrometry

To monitor the fluctuations of dimethyl sulfur compounds at the seawater/atmosphere interface, an automated system was developed based on sequential injection analysis coupled with vapor generation-ion molecule reaction mass spectrometry (SIA-VG-IMRMS). Using this analytical system, dissolved dimethyl sulfide (DMS(aq)) and dimethylsulfoniopropionate (DMSP), a precursor to DMS in seawater, were monitored together sequentially with atmospheric dimethyl sulfide (DMS(g)). A shift from the equilibrium point between DMS(aq) and DMS(g) results in the emission of DMS to the atmosphere. Atmospheric DMS emitted from seawater plays an important role as a source of cloud condensation nuclei, which influences the oceanic climate. Water samples were taken periodically and dissolved DMS(aq) was vaporized for analysis by IMRMS. After that, DMSP was hydrolyzed to DMS and acrylic acid, and analyzed in the same manner as DMS(aq). The vaporization behavior and hydrolysis of DMSP to DMS were investigated to optimize these conditions. Frequent (every 30 min) determination of the three components, DMS(aq)/DMSP (nanomolar) and DMS(g) (ppbv), was carried out by SIA-VG-IMRMS. Field analysis of the dimethyl sulfur compounds was undertaken at a coastal station, which succeeded in showing detailed variations of the compounds in a natural setting. Observed concentrations of the dimethyl sulfur compounds both in the atmosphere and seawater largely changed with time and similar variations were repeatedly observed over several days, suggesting diurnal variations in the DMS flux at the seawater/atmosphere interface.

Recent advances in flow injection analysis

A dynamic development of methodologies of analytical flow injection measurements during four decades since their invention has reinforced the solid position of flow analysis in the arsenal of techniques and instrumentation of contemporary chemical analysis.

Fabrication of a miniaturized capillary waveguide integrated fiber-optic sensor for fluoride determination

Fluoride concentration is a key aspect of water quality and essential for human health.

Liquid waveguide spectrophotometric measurement of nanomolar ammonium in seawater based on the indophenol reaction with o-phenylphenol (OPP)

We describe a highly sensitive colorimetric method for the determination of nanomolar concentrations of ammonium in seawater based on the indophenol reaction with o-phenylphenol [(1,1'-biphenyl)-2-ol, abbreviated as OPP]. OPP is available as non-toxic, stable flaky crystals with no caustic odor and has some advantages over phenol in practical use. The method was established by using a gas-segmented continuous flow analyzer equipped with two types of long path liquid waveguide capillary cell, LWCCs (100 cm and 200 cm) and an UltraPath (200 cm), which have inner diameters of 0.55 mm and 2 mm, respectively. The reagent concentrations, flow rates of the pumping tubes, and reaction path and temperature were determined on the basis of a manual indophenol blue method with OPP (Kanda, Water Res. 29 (1995) 2746-2750). The sample mixed with reagents that form indophenol blue dye was measured at 670 nm. Aged subtropical surface water was used as a blank, a matrix of standards, and the carrier. The detection limits of the analytical systems with a 100 cm LWCC, a 200 cm LWCC, and a 200 cm UltraPath were 6, 4, and 4 nM, respectively. These systems had high precision (<4% at 100 nM) and a linear dynamic range up to 200 nM. Non-linear baseline drift did not occur when using the UltraPath system. This is due to the elimination of cell clogging because of the larger inner diameter of the UltraPath compared to the LWCCs. The UltraPath system is thus more suitable for long-term measurements compared with the LWCC systems. The results of the proposed sensitive colorimetry and a conventional colorimetry for the determination of seawater samples showed no significant difference. The proposed analytical systems were applied to underway surface monitoring and vertical observation in the oligotrophic South Pacific.