Separation of cathode particles and aluminum current foil in Lithium-Ion battery by high-voltage pulsed discharge Part I: Experimental investigation

Chemical speciation changes of an all-solid-state lithium-ion battery caused by roasting determined by sequential acid leaching

All-solid-state lithium-ion batteries (ASS-LIBs) are expected to replace current liquid-based LIBs in the near future owing to their high energy density and improved safety. It would be preferable if ASS-LIBs could be recycled by the current recycling processes used for liquid-based LIBs, but this possibility remains to be determined. Here, we subjected an ASS-LIB test cell containing an argyrodite-type solid electrolyte (Li6PS5Cl) and nickel-manganese-cobalt-type active material (Li(Ni0.5Mn0.3Co0.2)O2) to roasting, a treatment process commonly used for recycling of the valuable metals from liquid-based LIBs, and investigated the changes in chemical speciation. Roasting was performed at various temperatures (350-900 °C), for various times (60-360 min), and under various oxygen fugacity (air or O2) conditions. The chemical speciation of each metal element after roasting was determined by sequential elemental leaching tests and X-ray diffraction analysis. Li formed sulfates or phosphates over a wide temperature range. Ni and Co followed very complicated reaction paths owing to coexistence of S, P, and C, and they formed sulfides, phosphates, and complex oxides. The optimum conditions for minimizing formation of insoluble compounds, such as complex oxides, were a roasting temperature of 450-500 °C and a roasting time of 120 min. The results indicated that although ASS-LIBs can be treated by the same roasting processes as those used for current liquid-based LIBs, the optimal roasting conditions have narrow ranges. Thus, careful process control will be needed to achieve high extraction percentages of the valuable metals from ASS-LIBs.

Ultra-fast recovery of cathode materials from spent LiFePO4 lithium-ion batteries by novel electromagnetic separation technology

The separation of electrode materials from current collectors plays a significant role in determining the leaching efficiency of different metals from spent lithium-ion batteries (LIBs). In the presented research, a highly efficient, environmentally sustainable, and cost-effective cathode materials separation strategy was proposed for spent LiFePO₄ batteries. Based on the difference in the thermal expansion coefficient of the binder and aluminum foil, the electromagnetic induction system was examined to harvest cathode materials for the first time, which could provide a high heating rate to erase the mechanical interlocking force between Al foil and coated material, and breaking the chemical bond or Van der Waals forces of the binder. The process avoids the usage of any chemicals such as acids and alkalis, thus eliminating the emission of wastewater. Our system shows ultra-fast separation (3 min) and achieves high-purity of recovered electrode materials and Al foils (99.6% and 99.2%). Furthermore, the morphology and crystalline structure of delaminated electrode materials remain almost the same compared with the pristine materials, which provides a previously unexplored technology to realize sustainable spent battery recycling.

Challenges in Recycling Spent Lithium-Ion Batteries: Spotlight on Polyvinylidene Fluoride Removal

In the recycling of retired lithium-ion batteries (LIBs), the cathode materials containing valuable metals should be first separated from the current collector aluminum foil to decrease the difficulty and complexity in the subsequent metal extraction. However, strong the binding force of organic binder polyvinylidene fluoride (PVDF) prevents effective separation of cathode materials and Al foil, thus affecting metal recycling. This paper reviews the composition, property, function, and binding mechanism of PVDF, and elaborates on the separation technologies of cathode material and Al foil (e.g., physical separation, solid-phase thermochemistry, solution chemistry, and solvent chemistry) as well as the corresponding reaction behavior and transformation mechanisms of PVDF. Due to the characteristic variation of the reaction systems, the dissolution, swelling, melting, and degradation processes and mechanisms of PVDF exhibit considerable differences, posing new challenges to efficient recycling of spent LIBs worldwide. It is critical to separate cathode materials and Al foil and recycle PVDF to reduce environmental risks from the recovery of retired LIBs resources. Developing fluorine-free alternative materials and solid-state electrolytes is a potential way to mitigate PVDF pollution in the recycling of spent LIBs in the EV era.

Selective separation of plastic LED lamp components using electrodynamic fragmentation for material recovery

The recycling of light-emitting diode (LED) lamps and tubes is becoming increasingly important due to their growing market share as energy-efficient lighting technology. Here we report on the use of high voltage electric-pulse fragmentation to recover elementary components such as LED chips and printed circuit boards (drivers). E27 LED lamps with plastic bulbs, which represent 48% of deposits collected by a French company, are used as a case study. More than 150 lamps were tested on a laboratory reactor for electrodynamic fragmentation. The technological process in which highly energetic electrical pulses were applied to materials immersed in water was studied in order to separate the components of the LED lamps using a minimal specific energy. The estimated energy necessary to achieve total separation assessed at 64%, without grinding pretreatment, was 5.2 ± 0.6 kWh per ton, representing a mass recycling rate of 74%. Based on the disassembled material, the commercial value of the recovered materials was thus estimated. Gold, as the most representative material, was found to represent 0.03% of the mass fraction for 83.6% of the total commercial value. The process disassembling capacity is a key issue to increase the recycling rate of current LED lamps and tubes.

Recycling of LiFePO4 cathode materials from spent lithium-ion batteries through ultrasound-assisted Fenton reaction and lithium compensation

Efficient exfoliation of cathode materials from current collectors for their direct regeneration is the typical bottleneck during spent lithium ion batteries (LIBs) recycling due to the strong adhesion of PVDF (polyvinylidene fluoride) binders. Ultrasound-assisted Fenton reaction was innovatively applied for the selective removal of PVDF binders to recover cathode materials of LiFePO₄ from current collectors and the recovered LiFePO₄ was regenerated through lithium compensation, targeting for the in-situ recycling of cathode materials from spent LIBs. Experimental results suggest that the PVDF binders were adequately degraded by hydroxyl radical (·OH) generated from Fenton's reagent with reinforcement of ultrasound, and about 97% cathode materials can be scrubbed from Al foils under optimized conditions. Detailed analytical results support that the cathode materials peeled off from current collectors are free from contamination of effluent, and the recovered LiFePO₄ can be directly re-fabricated as new cathode materials through lithium compensation with little reduction of electrochemical performances. And the tentative mechanism investigation for pathway of ·OH generation and chemical reactions indicates that ·OH generated from Fenton's reagent with the reinforcement of ultrasound can effectively degrade PVDF binders. This work can be a green and efficient candidate for the in-situ recycling of cathode materials of LiFePO₄ from spent LIBs.

Efficient separation of aluminum foil from mixed-type spent lithium-ion power batteries

The disposal of spent lithium-ion power batteries (LIBs) has become an important research topic owing to the booming market for electric vehicles. However, the recovery efficiency of the alkaline solution and organic solvent methods currently used to separate Al foil from cathode materials still has room for improvement. The insufficient separation of Al foil and complexity of the battery types present obstacles to the extraction of valuable metals using simple processes. In this study, an efficient approach is developed to separate the Al foil in mixed-type spent LIBs (M-LIBs), namely, LiNi_xCo_yMn_zO₂ (NCM), LiFePO₄ (LFP), and LiMn₂O₄ (LMO) LIBs, by controlled pyrolysis. Hundred percent of the Al foil was recovered at the temperature of 450 °C, holding time of 60 min, and heating rate of 10 °C/min. The purity of Al in the recovered foil was 99.41 %, 99.83 % and 99.92 %, and the recovery efficiency of the active cathode materials was 96.01 %, 99.80 % and 99.15 % for NCM, LFP and LMO, respectively, without the loss of active cathode materials. The obtained active cathode materials exhibited a favorable crystalline structure, and the average particle diameter was reduced from 300.497 to 24.316 μm with a smaller and looser morphology. The process could be well fitted with the Friedman differential equation, and the correlation coefficients were higher than 0.99. The efficient separation could be attributed to the complete rupture of long chain -(CH₂CF₂)-_n bonds in the poly (vinylidene difluoride) (PVDF) binder, which resulted in the formation of HF, trifluorobenzene, alkanes, and gaseous single molecule CH₂CF₂. Therefore, this work potentially provides an alternative approach for the efficient separation of Al foil in M-LIBs, thereby simplifying the process and achieving lower cost, reduced loss of valuable metals, and higher recovery efficiency.

Separation of cathode particles and aluminum current foil in lithium-ion battery by high-voltage pulsed discharge Part II: Prospective life cycle assessment based on experimental data

This series of papers addresses the recycling of cathode particles and aluminum (Al) foil from positive electrode sheet (PE sheet) dismantled from spent lithium-ion batteries (LIBs) by applying a high-voltage pulsed discharge. As concluded in Part I of the series (Tokoro et al., 2021), cathode particles and Al foil were separated in water based on a single pulsed power application. This separation of LIB components by pulsed discharge was examined by means of prospective life cycle assessment and is expected to have applications in LIB reuse and recycling. The indicators selected were life cycle greenhouse gas (LC-GHG) emissions and life cycle resource consumption potential (LC-RCP). We first completed supplementary experiments to collect redundant data under several scale-up circumstances, and then attempted to quantify the uncertainties from scaling up and progress made in battery technology. When the batch scale of pulsed discharge separation is sufficiently large, the recovery of cathode particles and Al foil from PE sheet by pulsed discharge can reduce both LC-GHG and LC-RCP, in contrast to conventional recycling with roasting processes. Due to technology developments in LIB cathodes, the reuse of positive electrode active materials (PEAM) does not always have lower environmental impacts than the recycling of the raw materials of PEAM in the manufacturing of new LIB cathodes. This study achieved a proof of concept for resource consumption reduction induced by cathode utilization, considering LC-GHG and LC-RCP, by applying high-voltage pulsed discharge separation.