The suitability of titanium salts in coagulation removal of micropollutants and in alleviation of membrane fouling

Mild Tuning of the Microbial Habitat via Titanium-Based Pre-coagulation Mitigates Reverse Osmosis Membrane Fouling

Membrane fouling remains a persistent challenge in reverse osmosis (RO) systems. Devising effective strategies to mitigate membrane fouling has become crucial for sustainable water treatment. Here, we propose a titanium-based pre-coagulation strategy for RO fouling mitigation through regulation of the microbial habitat in RO feed. The pre-coagulation performance of Ti(SO4)2 for desulfurization wastewater and the subsequent RO fouling mechanism were systematically investigated. Our findings revealed that the Ti pre-coagulation induced an acidized environment, maintained a balance between organic and inorganic depositions, and fostered a beneficial microbial community that resisted rapid fouling. The 20 day RO operations in different pre-coagulation scenarios (Ti, Al, and Ctrl) showed that the Ti group membranes maintained the highest normalized flux at 57.15%, outperforming the Ctrl and Al groups by 7.92% and 15.16%, respectively. Microbial community analyses, including taxonomic profiling and metagenomic analysis, demonstrated that Ti-based pre-coagulation reduced the dominance of extracellular polymeric substance (EPS)-secreting genera, such as Sphingopyxis, while promoting Terrimonas and Paenarthrobacter, with acid-tolerance traits and reduced EPS production. This shift mitigated biofouling by enhancing microbial balance and limiting biofilm formation. These results underscored the potential of the Ti pre-coagulation-based microbial habitat tuning strategy in enhancing RO system sustainability, offering a practical solution for improving industrial wastewater treatment.

Enhanced coagulation of Microcystis aeruginosa using titanium xerogel coagulant

Cyanobacterial blooms are prevalent globally and present a significant threat to water security. Titanium salt coagulants have garnered considerable attention due to their superior coagulation properties and the absence of metal residue risks. This paper explored the influencing factors in the coagulation process of titanium xerogel coagulant (TXC), the alterations in cell activity during floc storage, and the release of cyanobacterial organic matters, thereby determining the application scope of TXC for cyanobacterial water treatment. The findings indicated that at a TXC dosage of 8 mg Ti/L, the removal rate of Microcystis aeruginosa (M. aeruginosa) exceeded 86% across a pH range of 5-9. The coagulation performance with anions HCO3-, CO32- and H2PO4-/HPO42- was unsatisfactory at concentrations of 10, 20, and 50 mg/L, with corresponding chlorophyll a (Chl-a) levels of 168, 129, and 196 μg/L, respectively. While the presence of Cl-, NO3-, SO42-, K+, NH4+, Ca2+ and Mg2+ had little influence on the removal efficiency. At sodium alginate (SA) concentration of 6 mg/L, the Chl-a content was 116 μg/L, with humic acid (HA) not affecting M. aeruginosa removal but hindering turbidity reduction, leaving a residual turbidity of 11 NTU. Following TXC treatment, a floc storage study with cyanobacteria-laden surface water showed a decrease in microcystins (MCs) content. The low residual titanium concentration post-TXC coagulation (<0.06 mg/L) and MCs reduction contributed to reduced effluent toxicity, indicating TXC's versatile applicability for treating cyanobacterial-contaminated waters.

Uncovering the performance and intrinsic mechanism of different hydrolyzed AlTi species in polystyrene nanoplastics coagulation

Hydrolyzed AlTi species are essential metal-based coagulants in a coagulation process to remove nanoplastics (NPs). Understanding the molecular interactions between hydrolyzed AlTi species and NPs is key to promoting coagulation efficiency. In this study, the coagulation performance and intrinsic mechanism of different AlTi species (including monomeric AlTi and polymeric AlTi species-Al13Ti13) for NPs removal were systematically investigated. We found that the polymeric AlTi species exhibited higher turbidity removal (95.0 %) and lower residual Al content (20.67 μg/L) at a low dosage over monomeric AlTi species. Al13 and Al13Ti13 formed by in situ hydrolysis were the dominant species to destabilize and aggregate NPs at pH 6. Main coagulation mechanisms were dominated by charge neutralization, complexation between the aliphatic CH of NPs and Al/Ti-OH, and cation-π interaction between polycations and the aromatic structure of NPs. The preformed Al13Ti13 showed multiple positive charge binding sites assisting its easy adsorption on NPs by electrostatic attraction, and then formed microscale aggregates through charge neutralization or intermolecular interaction. The preformed Al13Ti13 demonstrated a high stability and coagulation performance with respect to pH changes in raw water, whereas the promotion of μ-OH bridges dissociation by OH- and the presence of electrostatic repulsion significantly decreased the NPs removal by monomeric AlTi at high pH. This study provides valuable theoretical insights into the interaction between NPs and various hydrolyzed AlTi species.

A membrane fouling control strategy based on a combination of pre-treatment mitigation and in-situ membrane surface regulation using a composite coagulant

Ultrafiltration technology (UF) is efficient in surface water treatment, but its development and widespread application are limited by membrane fouling. Herein, an efficient and stable polymerized ferric titanium coagulant (PFTC) was synthesized and used as a UF pretreatment agent in actual lake water treatment. The control mechanism of PFTC on membrane fouling was investigated from the perspective of organic removal efficiency and in-situ membrane surface regulation. PFTC demonstrated a remarkable affinity for soluble metabolic intermediates and hydrophilic proteins through complexation and hydrogen bonding force, achieving removal efficiencies of 66.4 % for UV254 and 81.3 % for DOC, respectively. The hydrophilic pollutants with high molecular weight and non-saturated structure could be preferentially removed by PFTC due to its diverse hydrolysates including positively charged Fe-based hydrolysates, amorphous Ti-based hydrolysates, and highly polymerized Fe-Ti copolymers. The flocs generated by PFTC exhibited strong hydrophilicity, allowing for the formation of a loose porous cake layer on the ultrafiltration membrane, which acted as a hydrophilic layer to enhance the anti-fouling performance of ultrafiltration membrane. With its dual function of contaminant removal and in-situ membrane surface regulation, PFTC alleviated 98.9 % of membrane fouling. This study provides new insights into membrane fouling control by coagulation pretreatment and efficient treatment of surface water.

Removal of 6-methylquinoline from shale gas wastewater using electrochemical carbon nanotubes filter

6-Methylquinoline (6-MQ) is identified as a high-concentration organic compound pervasive in shale gas wastewater (SGW) and poses a significant risk of environmental pollution. In response, this study aimed to address these challenges by introducing an innovative electrochemical membrane constructed with multi-walled carbon nanotubes (CNTs) for the removal of 6-MQ. The investigation systematically explored the impact of voltage, initial pollutant concentration, and salinity on the performance of the electrochemical CNTs filter. It was found a positive correlation between removal efficiency and increasing voltage and salinity levels. Conversely, as the initial concentration of pollutants increased, the efficiency showed a diminishing trend. The electrochemical CNTs filter exhibited remarkable efficacy in both adsorption removal and electrochemical oxidation of 6-MQ. Notably, the CNTs membrane exhibited robust adsorption capabilities, evidenced by the sustained adsorption of 6-MQ for over 33 h. Furthermore, applying an electrochemical oxidation voltage of 3 V consistently maintained a removal rate exceeding 34.0% due to both direct and indirect oxidation, underscoring the sustained efficacy of the electrochemical membranes. Besides, real wastewater experiments, while displaying a reduction in removal efficiency compared to synthetic wastewater experiments, emphasized the substantial potential of the electrochemical CNTs filter for practical applications. This study underscores the significant promise of electrochemical membranes in addressing low molecular weight contaminants in SGW, contributing valuable insights for advancing SGW treatment strategies.

Magnetic nanoparticle loading and application of weak magnetic field to reconstruct the cake layer of coagulation-ultrafiltration process to achieve efficient antifouling: Performance and mechanism analysis

Abandoning the costly development of new membrane materials and instead directly remodeling the naturally occurring cake layer constitutes a dynamic, low-cost, long-lasting, and proactive strategy to "fight fouling with fouling". Several optimization strategies, including coagulation/modified magnetic seed loading and applying a weak magnetic force (0.01T) at the ultrafiltration end, improved the anti-fouling, retention, and sieving performances of conventional ultrafiltration process during the treatment of source water having complex natural organic matter (NOMs) and small molecule micropollutants. Two modified magnetic seeds we prepared were composite nano-seed particles (Fe3O4@SiO2-NH2 (FS) and Fe3O4@SiO2@PAMAM-NH2 (FSP)). Aim of the study was to regulate the formation of cake layer via comprehensive testing of the antifouling properties of optimized processes and related mechanistic studies. It was found to be essential to enhance the interception of xanthate and tryptophan proteins in the cake layer for improving the anti-fouling performance based on the correlation and redundancy analyses, while the use of modified magnetic seeds and magnetic field showed a significant positive impact on water production. Blockage modeling demonstrated the ability to form a mature cake layer during the initial filtration stage swiftly. This mitigated the risk of irreversible fouling caused by pore blockage during the early stage of coagulation-ultrafiltration. Morphologically, the reconstructed cake layer exhibited elevated surface porosity, an internal cavity channel structure, and enhanced roughness that can promote increased water flux and retention of water impurities. These optimized the maturity of the cake layer in both time and space. Density Functional Theory (DFT), Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory, and Modified Extended Derjaguin-Landau-Verwey-Overbeek (MDLVO) calculations indicated aggregation behavior of matter on the cake layer to be enhanced effectively due to magnetic seed loading. This is mainly due to the strengthening of polar interactions, including hydrogen bonding, π-π* conjugation, etc., which can happen between the cake layer loaded with FSP and the organic matter. Under the influence of a magnetic field, magnetic force energy (VMF) significantly impacts the system by eliminating energy barriers. This research will provide innovative strategies for effectively purifying intricate source water through ultrafiltration while controlling membrane fouling.

Iron‑calcium dual crosslinked graphene oxide/alginate aerogel microspheres for extraordinary elimination of tetracycline in complex wastewater: Performance, mechanism, and applications

Antibiotics have been considered as a group of emerging contaminants for their stable chemical structure, significant pseudo-persistence, and biological toxicity. Tetracycline (TC), as one of the typical antibiotics frequently detected in environmental media, can cause the dissemination and accumulation of antibiotic resistance gene (ARG), ultimately threatening human health and environmental safety. Herein, a novel iron‑calcium di-crosslinked graphene oxide/alginate (GO/SA-Fe3+-Ca2+) aerogel was facilely synthesized for TC uptake. It was found that the introduction of GO nanosheets and Fe3+ sites into composite enormously enhanced TC removal. Specifically, TC can be stably and efficiently eliminated over the wide pH range of 5-8. The fitted maximum qe with Liu isotherm model at 308 K reached 1664.05 mg/g, surpassing almost all reported sorbents. The pseudo-second-order kinetic model with chemical sorption characteristics better fitted TC adsorption process, which was endothermic and spontaneous in nature. Multifarious adsorptive sites of GO/SA-Fe3+-Ca2+ synergically participated in TC uptake through multi-mechanisms (e.g., π-π EDA, cation-π bonding, H-bonding, Fe3+-coordination, and electrostatic attraction, etc.). The as-prepared composite showed satisfactory TC removal in several runs of adsorption-desorption operations, high salinity, and model aquaculture wastewater. Moreover, the packed-column could continuously run for >200 h until adsorption saturation was achieved with a dynamic adsorption capacity of 216.69 mg/g, manifesting its scale-up engineering applications. All above merits make as-constructed composite an alternative sorbent for eliminating TC from complex wastewater.

Simultaneous chelated heavy metals removal and sludge recovery through titanium coagulation: From waste to resource

Green methods for chelated heavy metals treatment and recovery are essential for coordinated development of resources and environment. Herein, a simple and competent method, titanium salt (TiCl4) coagulation was developed to remove and recycle chelated heavy metals. Our results revealed that this method proved to be effective for metals-citrate [Cu(II), Ni(II), Zn(II) and Cr(VI)], achieving removal efficiencies of 95 %, 92 %, 99 %, and 99 % within 30 min, surpassing direct alkaline precipitation and well-used Fe(III) coagulation. Whereafter, the copper-containing sludge was successfully transformed into copper-doped titanium dioxide (TiO2) photocatalysts by facile calcination. Through comprehensively investigating physicochemical properties by a suite of characterization techniques, we confirmed that doping of Cu induced bandgap narrowing, high specific surface area as well as the formation of oxygen vacancy. Accordingly, the recycling photocatalysts showed remarkable enhanced photocatalytic performance than the pristine TiO2, achieving improvement in the degradation efficiency of 82 %, 61 % and 67 % for carbamazepine(CBZ), bisphenol A (BPA) and methyl orange (MO). In addition, both radical (OH and O2-) and non-radical (1O2 and h+) pathways synergistically contributed to the removal of organic pollutants during photocatalysis. Ultimately, based on economic feasibility assessment and life cycle assessment (LCA), the copper-containing titanium coagulation sludge reuse for photocatalyst could bring lower carbon emissions, reduced environmental risks and higher economic benefits. The elucidation of this study provides new insights into the removal and recycle of chelated heavy metals from wastewater by using an environment-friendly and cost-effective method.

Dyeing sludge-derived biochar for efficient removal of antibiotic from water

Adsorption is one of the most effective methods for ecotoxic antibiotics removal, while developing high-performance adsorbents with excellent adsorption capacity is indispensable. As the unavoidable by-product of wastewater, sewage sludge has dual properties of pollution and resources. In this study, dyeing sludge waste was converted to biochar by KOH activation and pyrolysis, and used as an efficient adsorbent for aqueous antibiotics removal. The optimized dyeing sludge-derived biochar (KSC-8) has excellent specific surface area (1178.4 m2/g) and the adsorption capacity for tetracycline (TC) could reach up to 1081.3 mg/g, which is four and five times higher than those without activation, respectively. The PSO (pseudo-second-order) kinetic model and the Langmuir isotherm model fitted better to the experimental data. The obtained KSC-8 has stabilized adsorption capacity for long-term fixed-bed experiments, and maintained 86.35% TC removal efficiency after five adsorption-regeneration cycles. The adsorption mechanism involves electrostatic attraction, hydrogen bonding, π-π interactions and pore filling. This work is a green and eco-friendly way as converting the waste to treat waste in aiming of simultaneous removal of antibiotics and resource recovery of dyeing sludge.

Synergistic roles of oxidation and self-aggregation in efficient ultrafiltration membrane fouling alleviation using a flow-through Sb-SnO2 anode during wastewater reclamation

The application of ultrafiltration (UF) in wastewater reclamation alleviates the demand for limited water supplies. However, the membrane fouling caused by the effluent organic matter (EfOM) becomes a major obstacle for UF application. In this study, a pre-oxidation strategy for UF using a Sb-SnO2 (ATO) anode in flow-through mode was proposed with the hopes to improve the performance of UF during wastewater reclamation. The results indicated that this flow-through ATO (FA) anode significantly outperformed a boron-doped diamond (BDD) anode in terms of EfOM degradation and membrane fouling control. It is noteworthy that apart from oxidation, the self-aggregation behavior of foulants was also involved in the mechanisms of membrane fouling mitigation. On the one hand, FA pre-oxidation relieved the burden of membrane fouling by decomposing the macromolecular EfOM into small molecular organic matter, and even mineralizing it. The effective destruction of unsaturated EfOM by FA pre-oxidation made a remarkable contribution to fouling mitigation due to the strong correlation between the total fouling index and UV254. On the other hand, the surface morphology of membrane and interface properties of foulants revealed the self-aggregation behavior of foulants. FA pre-oxidation made the foulants aggregate spontaneously and reduced the potential of forming a dense cake layer on the membrane surface, which was conductive for water permeation. Overall, FA pre-oxidation proved to be a feasible and chemical-free option for UF pretreatment to simultaneously produce high-quality reused water and alleviate membrane fouling during wastewater reclamation.

Microcosmic mechanism analysis of the combined pollution of aged polystyrene with humic acid and its efficient removal by a composite coagulant

The composite pollutants formed by aged polystyrene (APS) and natural organic matter are complex and harmful, which lead to the deterioration of water quality. In this work, the interaction mechanism between humic acid (HA) and APS was discussed by investigating the changes in their functional groups. Besides, a novel polyaluminum-titanium chloride composite coagulant (PATC) was prepared, and its binding behaviors with HA@APS under different pH conditions were analyzed from a microscopic perspective. It was found that at pH 4, π-π conjugation was the dominant interaction between HA and APS. And the main removal mechanism of HA@APS by PATC was surface complexation. With the increase of pH, π-π conjugation, n-π electron donor-acceptor interaction (EDA), and hydrogen bonding gradually dominated the interaction between APS and HA. At pH 7, PATC hydrolyzed to form various polynuclear Al-Ti species, which could meet the demand for different binding sites of HA@APS. Under alkaline conditions, HB and n-π EDA in HA@APS were weakened, while π-π conjugation held a dominant position again. At this time, the main coagulation mechanism of PATC changed from charge neutralization to sweeping action, accompanied by hydrogen bonding. ENVIRONMENTAL IMPLICATION: Microplastics (MPs) have attracted the public's attention due to their potential toxicity to humans. The combined pollution of aged microplastics and humic acid (HA) will bring great harm to aquatic environment. The development of novel composite coagulants is hopeful to efficiently remove MPs and their combined pollutants. Elucidating the interactions between HA and aged MPs is helpful to understand the transformation and fate of MPs in actual environments, and to reveal the removal mechanism of composite pollutants by coagulation. The findings presented here will provide theoretical guidance for addressing the challenges of coagulation technology in treating new pollutants in practice.

Protein-folding-inspired approach for UF fouling mitigation using elevated membrane cleaning temperature and residual hydrophobic-modified flocculant after flocculation-sedimentation pre-treatment

Hydrophobic-modified flocculants have demonstrated considerable promise in the removal of emerging contaminants by flocculation. However, there is a lack of information about the impacts of dosing such flocculants on the performance of subsequent treatment unit(s) in the overall water treatment process. In this work, inspired by the ubiquitous protein folding phenomenon, an innovative approach using an elevated membrane cleaning temperature as the means to induce residual hydrophobic-modified chitosan flocculant (TRC), after flocculation-sedimentation, to reduce membrane fouling in a subsequent ultrafiltration was proposed; this was evaluated in a continuous flocculation-sedimentation-ultrafiltration (FSUF) process treating samples of the Yangtze River. The hydrophobic chains of TRC had similar temperature-dependent hydrophobicity to those of natural proteins. In the 40-day operation of the FSUF system with combined dosing of alum and TRC, a moderately elevated cleaning water temperature (45 °C) of both backwash with air-bubbling and soaking with sponge-scrubbing cleaning, significantly reduced reversible and irreversible fouling resistance by 49.8%∼61.3% and 73.9%∼83.3%, respectively, compared to the system using cleaning water at 25 °C. Material flow analysis, statistical analysis, instrumental characterizations, and computational simulations, showed that the enhanced fouling mitigation originated from three factors: the reduced contaminant accumulation onto membranes, the strengthened membrane-surface-modification role of TRC, and the weakened structure of the fouling material containing TRC, at the elevated cleaning temperature. Other measures of the performance, these being water purification, membrane stability and economic aspects, also confirmed the potential and feasibility of the proposed approach. This work has provided new insights into the role of hydrophobic-modified flocculants in membrane fouling control, in addition to emerging contaminant removal, in a FSUF surface water treatment process.

The suitability and mechanism of polyaluminum-titanium chloride composite coagulant (PATC) for polystyrene microplastic removal: Structural characterization and theoretical calculation

Microplastics (MPs) particles bring potential threats to the aqueous environment, and the coexistence of natural organic matter (NOM) enhances their toxicity. Coagulation is an efficient method for particle removal and exploring the binding sites and modes of the coagulant hydrolysates with MPs in the presence of NOM is essential to understand the coagulation mechanism. In this study, a novel polymerized polyaluminum-titanium chloride composite coagulant (PATC) was prepared and used to remove polystyrene (PS). It was found that PATC could compress or even destroy the surface layer of the negatively charged PS. In comparison to PAC and PTC, PATC was more efficient in decreasing the energy barrier of the PS particles and increasing their aggregation rate over a wider pH range. The results of the Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) calculation revealed that the interaction between the hydrolysates of PATC and PS was mainly polar interaction (V_AB), such as hydrogen bonding. The peak intensity and peak shift in Fourier-transformed infrared (FTIR) and X-ray photoelectron spectra (XPS) were analyzed to further explore the interaction between the hydrolysates of PATC and PS. It was found that hydrogen bonding existed between the -OH group of PATC and the aliphatic C-H and C=O groups of PS. And the main interaction between HA and PS was the π-π* conjugation and hydrogen bonding between the -COOH, -OH, and C=O groups of HA and the C=O and aliphatic C-H groups of PS. Therefore, in the HA@PS system, the active sites of HA (e.g. -COOH and -OH) and PS (e.g., C=O and aliphatic C-H) binding with the coagulants were occupied, which accordingly led to the dramatic decline in the removal efficiency of both HA and PS. In actual lake water treatment, although the removal efficiency of PS was significantly poor, PATC performed better for PS removal than PAC and PTC. Besides, the effluent pH was maintained at 6.81±0.08, which met the requirements of the subsequent water treatment process. This study provides systematic knowledge for understanding the interaction between PS, NOM, and coagulant hydrolysates, and further confirms the application potential of PATC for MPs removal.

BSA-Cu3(PO4)2 hybrid nanoflower-an efficient and low-cost nanoenzyme for decolorization of organic pollutants

The Fenton reaction is one of the most effective methods for treating organic wastewater, which is extremely harmful to humans but difficult to treat. However, finding simple, low-cost, and efficient catalysts for the Fenton reaction remains a challenge. In this study, a BSA-Cu₃(PO₄)₂ hybrid nanoflower (NF) was synthesized to investigate its peroxidase-like activity for the treatment of organic wastewater. Its morphology, composition, and crystallization had been fully studied and the results confirmed that the NFs were successfully prepared. Subsequently, the origin of the peroxidase-like activity of the NFs was further analyzed, with the results suggesting two reasons: (i) the transformation between Cu(I) and Cu(II) and (ii) nano-effects. Additionally, Congo red was selected as the organic pollutant to simulate the decolorization of wastewater. After 3 h, the decolorization efficiency reached 96%. Furthermore, the NFs exhibited good storage performance, maintaining approximately 90% relative activity after storage for 30 days. In summary, the NFs have great application prospects in the treatment of organic wastewater.

Construction of titanium-aluminum xerogel composite coagulant for removal of tetracycline in water: synergy effects and improvement mechanisms insight

Titanium xerogel coagulant (TXC) is a new type of coagulant that has attracted much attention in recent years. However, the tetracycline removal performance of TXC was not satisfactory because low isoelectric point (pH_iep) inhibited the electrical neutralization efficiency of TXC in an alkaline environment. To overcome this shortcoming, a composite xerogel coagulant (titanium-aluminum xerogel composite coagulant) was prepared. The removal of tetracycline and turbidity was used as evaluation indexes. It was proved that the combination of aluminum (III) and titanium (IV) enhanced the resistance of TXC to pH. The synthesized titanium-aluminum xerogel composite coagulant (TXAC) has an excellent removal ability of tetracycline in a wide pH range (pH = 5-10). At pH 8.8, the dosage required to remove 80% tetracycline from water decreased from 93 (TXC) to 35 mg/L (TXAC). The reason for this improvement could be attributed to (i) aluminum (III) enhanced the electric neutralization of TXC to negatively charged pollutants in an alkaline environment; (ii) the complexing ability of organic matter and aluminum (III) was enhanced. This work provides a feasible scheme for the pretreatment of tetracycline in water to meet the pretreatment requirements of special water.

Antimony (Sb) pollution control by coagulation and membrane filtration in water/wastewater treatment: A comprehensive review

Antimony (Sb) pollution in the water environment caused by the large-scale mining of Sb ore and the wide use of Sb-containing products seriously endangers human health and poses a great threat to the ecological environment. Coagulation is one of the most cost-effective technologies for Sb pollution control in water/wastewater treatment and has been widely used. However, a comprehensive understanding of Sb pollution control by coagulation, from fundamental research to practical applications, is lacking. In this work, based on the current status of Sb pollution in the water environment, a critical review of the Sb removal performance and mechanism by coagulation and related combined processes was carried out. The influencing factors of Sb removal performance by coagulation are introduced in detail. The internal mechanisms and improvement strategies of Sb removal by oxidation/reduction-coagulation and coagulation-membrane filtration technologies are emphasized. Moreover, given the development of Sb-removing coagulants and the resource utilization of Sb-containing sludge, future perspectives of coagulation for Sb removal are discussed. As the first review in this field, this work will illuminate avenues of basic research and practical applications for Sb and Sb-like pollution control in water/wastewater treatment.

Insight into core -shell microporous zinc silicate adsorbent to eliminate antibiotics in aquatic environment under the COVID-19 pandemic

Under the new crown pneumonia (COVID-19) epidemic, the intensive use of therapeutic drugs has caused certain hidden danger to the safety of the water environment. Therefore, the core-shell microporous zinc silicate (SiO₂@ZSO) was successfully prepared and used for the adsorption of chloroquine phosphate (CQ), tetracycline (TC) and ciprofloxacin (CIP) for eliminating the threat of COVID-19. The adsorption efficiencies of 20 mg L^-1 of CQ, TC and CIP by SiO₂@ZSO were all up to 60% after 5 min. The adsorption capacity of SiO₂@ZSO for CQ, TC and CIP can reach 49.01 mg g^-1, 56.06 mg g^-1 and 104.77 mg g^-1, respectively. The adsorption process is primarily physical adsorption, which is heterogeneous, spontaneous and preferential. Moreover, the effects of temperature, pH, salinity, and reusability on the adsorption of CQ, TC, and CIP on SiO₂@ZSO were investigated. The adsorption mechanism mainly involves electrostatic attraction, partitioning and hydrogen bonding, which is insightful through the changes of the elements and functional groups before and after adsorption. This work provides a solution to the problems faced by the treatment of pharmaceuticals wastewater under the COVID-19 epidemic.

Coagulation behavior of polyaluminum-titanium chloride composite coagulant with humic acid: A mechanism analysis

The hydrolysate species of metal-based coagulants and the binding sites of humic acid (HA) are highly dependent on the pH conditions. Exploring the binding sites and modes between coagulant hydrolysates and HA molecules is critical to understanding the coagulation mechanism. In this paper, the binding behavior between HA molecules and the hydrolysates of a polyaluminum-titanium chloride composite coagulant (PATC) was investigated under different pH conditions by semi-quantitative FTIR and XPS. It was found that oligomeric and mesopolymeric hydrolysates were the dominant species under acid conditions, which could complex with the hydroxyl and carboxyl groups of HA by forming COAl/Ti coordinate bonds. However, large amounts of H⁺ could compete with Al³⁺ and weaken the removal efficiency of HA. With the increase of pH, the hydrolysis process of the PATC and the deprotonation of HA were simultaneously underway. Under weakly acid conditions, the complexation of the aluminum hydrolysates with carboxyl groups was improved due to the gradually diminishing competition of H⁺ and the enhanced charge neutralization of the further polymerized hydrolysates. Consequently, the maximum UV₂₅₄ removal by adding PATC was observed at pH 6. Under alkaline conditions, the sweeping effect of amorphous hydroxide dominated the HA removals, which was accompanied by the surface complexation of Al/Ti nuclear with carboxyl groups as well as the hydrogen bonds between hydroxyl and hydroxide. This study provides a new clue for the interaction mechanisms between the hydrolysates of composite coagulants and the dominant functional groups of HA at various pH conditions.