Analytical applications of tris(2,2′-bipyridyl)ruthenium(III) as a chemiluminescent reagent

Determination of pioglitazone hydrochloride by flow injection chemiluminescence tris(2,2'-bipyridyl)ruthenium(II)-silver(III) complex system

A novel flow injection-chemiluminescence (FI-CL) approach is proposed for the assay of pioglitazone hydrochloride (PG-HCl) based on its enhancing influence on the tris(2,2'-bipyridyl)ruthenium(II)-silver(III) complex (Ru(bipy)₃ ²⁺ -DPA) CL system in sulfuric acid medium. The possible CL reaction mechanism is discussed with CL and ultraviolet (UV) spectra. The optimum experimental conditions were found as: Ru(bipy)₃ ²⁺ , 5.0 × 10^-5  M; sulfuric acid, 1.0 × 10^-3  M; diperiodatoargentate(III) (DPA), 1.0 × 10^-4  M; potassium hydroxide, 1.0 × 10^-3  M; flow rate 4.0 ml min^-1 for each flow stream and sample loop volume, 180 μl. The CL intensity of PG-HCl was linear in the range of 1.0 × 10^-3 to 5.0 mg L^-1 (R²  = 0.9998, n = 10) with limit of detection [LOD, signal-to-noise ratio (S/N) = 3] of 2.2 × 10^-4  mg L^-1 , limit of quantification (LOQ, S/N = 10) of 6.7 × 10^-4  mg L^-1 , relative standard deviation (RSD) of 1.0 to 3.3% and sampling rate of 106 h^-1 . The methodology was satisfactorily used to quantify PG-HCl in pharmaceutical tablets with recoveries ranging from 93.17 to 102.77 and RSD from 1.9 to 2.8%.

Electrochemiluminescence of Ru(bpy)32+/thioacetamide and its application for the sensitive determination of hepatotoxic thioacetamide

Thioacetamide (TAA) is a well-known hepatotoxic substance, so it is important to determine its presence and content in food and environmental samples. Herein, we report a highly sensitive determination method for TAA based on the electrochemiluminescence (ECL) of tris(2,2'-bipyridyl)ruthenium(ii) (Ru(bpy)32+) for the first time by using TAA as a new coreactant for Ru(bpy)32+ ECL via an anodic route. The developed Ru(bpy)32+-TAA ECL system allows the determination of TAA with a good dynamic linear range and low limit of detection (LOD) of 0.1 μM to 1000 μM and 0.035 μM (3σ/m), respectively. In addition, the established ECL system can be applied to detect TAA in fruit juice and waste water samples with outstanding recoveries.

Flow injection-chemiluminescence determination of cetirizine dihydrochloride in pharmaceuticals using tris(2,2'-bipyridyl)ruthenium (II)-Ag(III) complex reaction

A simple and sensitive flow injection-chemiluminescence (FI-CL) method was developed for determination of cetirizine dihydrochloride (CTZH) in pharmaceuticals. The method is primarily based on the enhancement effect of CTZH on the tris(2,2'-bipyridyl)ruthenium (II)-diperiodatoargentate (III) ([Ru(bpy)₃ ]²⁺ -Ag(III) complex) CL system in an acidic medium. The optimum investigated variables of the CL reaction were: [Ru(bpy)₃ ]²⁺ , 50 × 10^-6 mol/L; sulfuric acid, 1.0 × 10^-3 mol/L; Ag(III) complex, 100 × 10^-6 mol/L; potassium hydroxide, 1.0 × 10^-3 mol/L; flow rate, 3.0 ml/min and sample loop volume, 300 μl. The detection and quantification limits were 2.0 × 10^-4 and 5.0 × 10^-4 mg/L (S/N of 3 and 10) respectively with a linear calibration range of 5.0 × 10^-4 to 7.5 mg/L (R² = 0.9999, n = 11), injection throughput of 110/h and the relative standard deviations of 1.5-3.5% over the range studied. The methodology was successfully applied to determine CTZH in different pharmaceutical samples and validated with a high-performance liquid chromatography method, and resulted in the recovery of 94.6-108.6%. The probable CL reaction mechanism is described in brief.

Recent Advances in Aggregation-Induced Electrochemiluminescence

The emergence of the rising alliance between aggregation-induced emission (AIE) and electrochemiluminescence (ECL) is defined as aggregation-induced electrochemiluminescence (AIECL). The booming science of AIE has proved to be not only distinguished in luminescent materials but could also inject new possibility into ECL analysis. Especially in the aqueous phase and solid state for hydrophobic materials, AIE helps ECL circumvent the dilemma between substantial emission intensity and biocompatible media. The wide range of analytes makes ECL an overwhelmingly interesting analytical technique. Therefore, AIECL has gained potential in clinical diagnostics, environmental assays, and biomarker detections. This review will focus on introduction of the novel concept of AIECL, current applied luminophores, and related applications developed in recent years.

The recognition and electrochemiluminescence response of benzo[6]urils to polycyclic aromatic hydrocarbons

The electrochemiluminescence of benzo[6]urils was discovered and applied for molecular recognition based on the host–guest interactions with polycyclic aromatic hydrocarbons.

Rapid and sensitive spectroelectrochemical and electrochemical detection of glyphosate and AMPA with screen-printed electrodes

N-(Phosphonomethyl)glycine (glyphosate), known by the trade name Roundup®, is a broad spectrum systemic herbicide used to kill several types of grass weed. The hazard potential of Roundup® is unclear, which is a serious issue within the European Union; however, after an intense debate, the EU Commission extended its approval of glyphosate use until the end of 2017. A persistent need exists for rapid, inexpensive, and sensitive detection of glyphosate and (aminomethyl)phosphonic acid (AMPA), the hydrolysis product of glyphosate. This article presents reliable and easily performed (spectro)electrochemical measurements (e.g., electrogenerated chemiluminescence (ECL) and fast amperometry) for identifying glyphosate and AMPA on the basis of [Ru(bpy)3]2+. The limit of detection of both methods is also determined in this study. The main feature of the (spectro)electrochemical methods is screen-printed electrodes (SPE) that are made from either gold or multi-walled carbon nanotubes (MWCNTs), optionally decorated with nano-ZnO. Nano-ZnO can significantly enhance the ECL signal to result in a detection limit lower than 1μmol/L for glyphosate. In addition, these methods are cheaper, faster, and more sensitive than, for example, spectroscopic tests.

Determination of pholcodine in syrups and human plasma using the chemiluminescence system of tris(1,10 phenanthroline)ruthenium(II) and acidic Ce(IV)

Pholcodine is an opiate derivative drug which is widely used in pediatric medicine. In this study, a chemiluminescence (CL) method is described that determines pholcodine in human plasma and syrup samples. This method is based on the fact that pholcodine can greatly enhance the weak CL emission of reaction between tris(1,10 phenanthroline)ruthenium(II), Ru(phen)₃²⁺ , and acidic Ce(IV). The CL mechanism is described in detail using UV-vis light, fluorescence and CL spectra. Effects of chemical variables were investigated and under optimum conditions, CL intensity was proportional to the pholcodine concentration over the range 4.0 × 10^-8 to 8.0 × 10^-6  mol  L^-1 . The limit of detection (LOD) (S/N = 3) was 2.5 × 10^-8  mol  L^-1 . Percent of relative standard deviations (%RSD) for 3.0 × 10^-7 and 3.0 × 10^-6  mol  L^-1 of pholcodine was 2.9 and 4.0%, respectively. Effects of common ingredients were investigated and the method was applied successfully to the determination of pholcodine in syrup samples and human plasma.

Excited state decay of cyclometalated polypyridine ruthenium complexes: insight from theory and experiment

This perspective article tackles the open question why cyclometalated polypyridine ruthenium(ii) complexes typically only emit very weakly at room temperature and delivers answers beyond the standard schemes involving ³MC and tunneling decay channels.

Immobilizing water-soluble graphene quantum dots with gold nanoparticles for a low potential electrochemiluminescence immunosensor

Hydrazide-modified graphene quantum dots (HM-GQDs) obtained by refluxing GQDs with hydrazine hydrate were hybridized with gold nanoparticles (AuNPs) through a redox reaction between HM-GQDs and AuCl4(-). The obtained nano-hybrids (HM-GQD-AuNPs) possess the unique electrochemiluminescence (ECL) properties of HM-GQDs and the easy self-assembly with some bio-molecules of AuNPs, which have great potential applications in bio-sensors. HM-GQD-AuNPs were modified on a glassy carbon electrode to develop a novel ECL immunosensor of carcinoembryonic antigen (CEA) as a model target analyte. Due to the increment of electron-transfer resistance after immunoreaction, the ECL intensity decreased as the concentration of CEA was increased. The linear response range was between 0.02 and 80 ng mL(-1), and the detection limit was 0.01 ng mL(-1).

Photoluminescence, chemiluminescence and anodic electrochemiluminescence of hydrazide-modified graphene quantum dots

Single-layer graphene quantum dots (SGQDs) were refluxed with hydrazine (N2H4) to prepare hydrazide-modified SGQDs (HM-SGQDs). Compared with SGQDs, partial oxygen-containing groups have been removed from HM-SGQDs. At the same time, a lot of hydrazide groups have been introduced into HM-SGQDs. The introduced hydrazide groups provide HM-SGQDs with a new kind of surface state, and give HM-SGQDs unique photoluminescence (PL) properties such as blue-shifted PL emission and a relatively high PL quantum yield. More importantly, the hydrazide-modification made HM-SGQDs have abundant luminol-like units. Accordingly, HM-SGQDs exhibit unique and excellent chemiluminescence (CL) and anodic electrochemiluminescence (ECL). The hydrazide groups of HM-SGQDs can be chemically oxidized by the dissolved oxygen (O2) in alkaline solutions, producing a strong CL signal. The CL intensity is mainly dependent on the pH value and the concentration of O2, implying the potential applications of HM-SGQDs in pH and O2 sensors. The hydrazide groups of HM-SGQDs can also be electrochemically oxidized in alkaline solutions, producing a strong anodic ECL signal. The ECL intensity can be enhanced sensitively by hydrogen peroxide (H2O2). The enhanced ECL intensity is proportional to the concentration of H2O2 in a wide range of 3 μM to 500 μM. The detection limit of H2O2 was calculated to be about 0.7 μM. The results suggest the great potential applications of HM-SGQDs in the sensors of H2O2 and bio-molecules that are able to produce H2O2 in the presence of enzymes.

Ruthenium polypyridine complexes combined with oligonucleotides for bioanalysis: a review

Ruthenium complexes are among the most interesting coordination complexes and they have attracted great attention over the past decades due to their appealing biological, catalytic, electronic and optical properties. Ruthenium complexes have found a unique niche in bioanalysis, as demonstrated by the substantial progress made in the field. In this review, the applications of ruthenium complexes coordinated with polypyridine ligands (and analogues) in bioanalysis are discussed. Three main detection methods based on electrochemistry, electrochemiluminescence, and photoluminscence are covered. The important targets, including DNA and other biologically important targets, are detected by specific biorecognition with the corresponding oligonucleotides as the biorecognition elements (i.e., DNA is probed by its complementary strand and other targets are detected by functional nucleic acids, respectively). Selected examples are provided and thoroughly discussed to highlight the substantial progress made so far. Finally, a brief summary with perspectives is included.

Graphene platform used for electrochemically discriminating DNA triplex

Triplex DNA has received great attention as new molecular biology tools and therapeutic agents due to their possible novel functions in biology systems. Therefore, it is important to distinguish triplex from among different forms of DNA, such as single-stranded and double-stranded DNA. In this report, several electrochemical techniques, cyclic voltammetry, electrochemical impedance spectroscopy, different pulse voltammetry, and electrochemiluminescence were used for distinguishing this unique structure among different DNA formations by using functionalized graphene/Nafion-Ru(bpy)3(2+) (bpy = 2, 2'-bipyridine) modified glass carbon electrode. The different interactions between nucleotides and graphene surface and Ru(bpy)3(2+) mediated guanine oxidation produced quite different electrochemical responses. Guanine bases are hidden inside the folded triplex DNAs, which are much less susceptible to be oxidized by Ru(bpy)3(3+) produced on electrodes. Furthermore, the effect of guanine bases stacking in triplex also influences the electrochemical behaviors. By changing the different position and distance of guanine bases in DNA sequences, we found that the conjoint way of several guanines strongly influenced the catalytic electrochemical responses on graphene surface. Our results provide new insight into determination of less stable protonated triplex formation by using graphene-based rapid, low-cost and sensitive electrochemical techniques.

Graphene quantum dots/L-cysteine coreactant electrochemiluminescence system and its application in sensing lead(II) ions

A new coreactant electrochemiluminescence (ECL) system including single-layer graphene quantum dots (GQDs) and L-cysteine (L-Cys) was found to be able to produce strong cathodic ECL signal. The ECL signal of GQD/L-Cys coreactant system was revealed to be mainly dependent on some key factors, including the oxidation of L-Cys, the presence of dissolved oxygen and the reduction of GQDs. Then, a possible ECL mechanism was proposed for the coreactant ECL system. Furthermore, the ECL signal of the GQD/L-Cys system was observed to be quenched by lead(II) ions (Pb(2+)). After optimization of some important experimental conditions, including concentrations of GQDs and L-Cys, potential scan rate, response time, and pH value, an ECL sensor was developed for the detection of Pb(2+). The new methodology can offer a rapid, reliable, and selective detection of Pb(2+) with a detection limit of 70 nM and a dynamic range from 100 nM to 10 μM.

Determination of folates by HPLC-chemiluminescence using a ruthenium(II)-cerium(IV) system, and its application to pharmaceutical preparations and supplements

A chemiluminescence (CL) reaction of folic acid (FA) with ruthenium (II) and cerium (IV) was applied to quantify FA-related compounds such as FA, dihydrofolic acid, tetrahydrofolic acid, 5-methyltetrahydrofolic acid, 5-formyltetrahydrofolic acid and methotrexate (MTX). Among the FAs, 5-methyltetrahydrofolic acid provided the highest CL intensity. HPLC-CL detection of FA was applied to quantify FA in pharmaceutical preparations and supplements. Analytical samples were separated on a semi-micro ODS column with a mixture of 20 mM phosphate buffer (pH 5.7) and acetonitrile (94 : 6, v/v %). The separated samples were mixed with a post-column CL reagent consisting of 1.5 mM Ru(bipy)3 (2+) and 1.0 mM Ce(SO4)2 , then the generated CL was monitored. The calibration range for FA was 10-100 μM and the limit of detection was 1.34 μM (signal-to-noise ratio of 3). Repeatabilities were 4.2, 4.6 and 5.0 RSD% (10, 25, 50 μM), and the recoveries for FA supplement, vitamin B complex supplement and FA-containing medication (tablet) were 102.4 ± 10.5, 103.3 ± 13.3 and 100.3 ± 8.5%, respectively. The described method is robust against changes in the chromatographic parameters of ± 3.3 or ± 1.5%. The measured FA content corresponded well to the labeled content of FA-containing products (100.6-104.9%), demonstrating the precision and accuracy of this method for the evaluation of FA pharmaceutical preparations.

Chemiluminescence determination of folic acid by a flow injection analysis assembly

A flow injection (FI) method is reported for the determination of folic acid by chemiluminescence method. This method is based on the reaction of folic acid with Ru(bipy)(3)(2+) and Ce(IV) to produce chemiluminescence. The calibration curve was linear over the range of 2.5×10(-5)-3.1×10(-7) mol/L with a detection limit of 2.3×10(-8) mol/L (S/N=3). The relative standard deviation of 1.0×10(-6) mol/L folic acid was found 3.5% (n=11). The influences of potential interfering substances were studied. The recovery was higher than 95.3%. The method was accurate, sensitive, and effective for assay of folic acid. This CL method was successfully applied to the determination of folic acid in pharmaceutical preparations. The mechanism of CL reaction was also studied.

High-relaxivity and luminescent silica nanoparticles as multimodal agents for molecular imaging

The design and synthesis of a new bimodal contrast agent for magnetic resonance imaging and optical imaging is reported. Tunable-sized silica nanoparticles were synthesized by a microemulsion-mediated pathway and used as carriers for paramagnetic and luminescent probes. The near-infrared luminescent agent was a ruthenium complex that was directly entrapped in the silica shell to provide photoluminescence enhancement and to make it highly photostable as it was protected from the surrounding environment. The paramagnetic activity came from a Gd-DTPA derivative that was grafted on the silica surface. NMRD profiles showed a strong relaxivity enhancement (increase of 432% in the r1 value at 20 MHz) when the paramagnetic complex was grafted at the nanoparticle surface, because of a reduction of its mobility. Polyethylene glycol was also grafted at the nanoparticle surface to enhance the nanoparticle residence time in the bloodstream. A thorough characterization of the material confirmed its potential as a very effective bimodal contrast agent.