Relationship between polyethylene wear, pelvic osteolysis, and clinical symptomatology in patients with cementless acetabular components. A framework for decision making

Excellent 20-Year Results of Total Hip Arthroplasty With Highly Cross-Linked Polyethylene on Cobalt-Chromium Femoral Heads in Patients ≤50 Years

BACKGROUND

Highly cross-linked polyethylene (HXLPE) acetabular bearing surfaces have appeared to offer excellent wear resistance, low incidence of wear-related osteolysis, and high implant survivorship at 10-year to 15-year follow-up. However, concerns over potential performance deterioration at longer-term follow-up remain - particularly in younger patients - and outcome data into the third decade have not been available.

METHODS

We retrospectively assessed 62 patients (68 hips) who underwent primary total hip arthroplasty (THA) at age ≤50 years with a single manufacturer's cementless components, remelted HXLPE liner, and small diameter (26 and 28 millimeter) cobalt-chromium (CoCr) femoral heads at minimum 18-year follow-up. We assessed clinical outcomes (modified Harris Hip score, University of California Los Angeles Activity Score, polyethylene wear rates, radiographic findings (osteolysis, component loosening), and implant survivorship.

RESULTS

At 20.6-year mean follow-up (range, 18 to 23 years) modified Harris Hip scores for surviving hips remained an average of 41 points above preoperative baseline (49 versus 90, P < .001) and UCLA scores 2.8 points above baseline (3.7 versus 6.4, P < .001). Wear analysis revealed a population linear wear rate of 0.0142 mm/y (standard deviation (SD), 0.0471) and volumetric wear rate of 10.14 mm3/y (SD, 23.41). Acetabular lysis was noted in 2 asymptomatic hips at 16.6 and 18.4 years. No components were radiographically loose. Survivorship free from wear-related revision was 100% at 20 years (97% free from any revision).

CONCLUSION

The HXLPE-CoCr bearing couple with small femoral heads continues to be extremely effective 20 years after primary THA in the younger patient population.

Long-Term Follow-Up of Conventional Polyethylene in Total Hip Arthroplasty in Young Patients: Heightened Wear-Related Complications Are Observed at the Beginning of the Third Decade

BACKGROUND

Conventional polyethylene (CPE) was used widely in the past as a bearing surface in total hip arthroplasty (THA). As CPE THAs age and the revision burden continues to grow, it is increasingly important to understand the durability and failure mechanisms of this bearing material. Currently, such long-term data remain limited, particularly in younger, more active patients in whom wear issues are of greater concern.

METHODS

We retrospectively reviewed 90 hips (77 patients) that underwent primary THA with CPE bearings on cobalt chrome femoral heads at age ≤50 years at 20-year minimum follow-up (mean 21.6 [20-23]). We analyzed polyethylene wear rates, clinical outcomes (modified Harris Hip Score, University of California, Los Angeles Activity Score), and implant survivorship.

RESULTS

Wear analysis revealed a median linear wear rate of 0.113 mm/y (95% CI 0.102-0.148) and a median volumetric wear rate of 41.20 mm³/y (95% CI 43.5-61.0). Modified Harris Hip Scores remained 37 points above preoperative baseline (P < .001) and University of California, Los Angeles scores 1.4 points above baseline (P = .018) at 21.6-year mean follow-up. Twenty-nine hips (32.2%) were revised, 20 of which (22.2%) were wear-related at a median of 15.4 years (interquartile range 11.4-19.5). Survivorship free from wear-related revision was 95.6% (95% CI 88.7-98.3), 87.9% (78.6-93.3), 78.1% (49.6-66.5), and 61.1% (41.3-67.0) at 10, 15, 20, and 25 years.

CONCLUSION

Wear-related issues developed at increasingly high rates after 15 years, suggesting the need for surveillance after this time. The long-term wear and survivorship data of this study may be used as a benchmark when evaluating the performance of contemporary bearings in young, active THA patients.

Polyethylene liner cementation into a well-fixed metal acetabular shell for the management of periacetabular osteolysis: a systematic review

PURPOSE

Although various papers have reported on the clinical performance of cup retention with cementation of a new liner and bone grafting in the management of well-fixed cups with polyethylene wear and periacetabular osteolysis after total hip arthroplasty (THA), no systematic review of this topic has been published to date.

METHODS

Medline, EMBASE and Cochrane Library were searched for articles published from January 1999 to January 2019 using "osteolysis" AND "well-fixed", "osteolysis" AND "retro-acetabular", "bone graft" AND ("retention" OR "retained" OR "stable") AND "cup", and "cemented liner" AND "well-fixed".

RESULTS

Nine articles were selected for review (186 cases, 76.1 months mean follow-up). The overall revision rate was 11.3% (21 hips) most commonly due to aseptic loosening (9/186 hips), dislocation (8/186 hips), and liner wear progression (2/186 cases). The reported square size of osteolytic lesions ranged from a mean of 465.84 mm² to a max of 4,770 mm². Almost all reported lesions treated with bone grafts resolved or did not progress 97% (72/74). All studies indicated improved pain and functional scores at follow-up.

CONCLUSION

Cementation of a new liner with periacetabular bone grafting provides an alternative option to isolated liner exchange and cup revision for the management of periacetabular osteolysis in well-fixed cups with a disrupted locking mechanism or unavailable exchange liner. Further higher quality studies are required in order to examine if the use of highly cross-linked polyethylene, highly porous-coated cups, hydroxyapatite-coated cups, and small-diameter cups influence the clinical outcome of liner cementation in well-fixed cups with periacetabular osteolysis.

Hybrid Self-Reinforced Composite Materials Based on Ultra-High Molecular Weight Polyethylene

The properties of hybrid self-reinforced composite (SRC) materials based on ultra-high molecular weight polyethylene (UHMWPE) were studied. The hybrid materials consist of two parts: an isotropic UHMWPE layer and unidirectional SRC based on UHMWPE fibers. Hot compaction as an approach to obtaining composites allowed melting only the surface of each UHMWPE fiber. Thus, after cooling, the molten UHMWPE formed an SRC matrix and bound an isotropic UHMWPE layer and the SRC. The single-lap shear test, flexural test, and differential scanning calorimetry (DSC) analysis were carried out to determine the influence of hot compaction parameters on the properties of the SRC and the adhesion between the layers. The shear strength increased with increasing hot compaction temperature while the preserved fibers' volume decreased, which was proved by the DSC analysis and a reduction in the flexural modulus of the SRC. The increase in hot compaction pressure resulted in a decrease in shear strength caused by lower remelting of the fibers' surface. It was shown that the hot compaction approach allows combining UHMWPE products with different molecular, supramolecular, and structural features. Moreover, the adhesion and mechanical properties of the composites can be varied by the parameters of hot compaction.

Outcome of a hemispherical porous-coated acetabular component with a proximally hydroxyapatite-coated anatomical femoral component

Aims

We previously reported the long-term results of the cementless Duraloc-Profile total hip arthroplasty (THA) system in a 12- to 15-year follow-up study. In this paper, we provide an update on the clinical and radiological results of a previously reported cohort of patients at 23 to 26 years´ follow-up.

Patients and Methods

Of the 99 original patients (111 hips), 73 patients (82 hips) with a mean age of 56.8 years (21 to 70) were available for clinical and radiological study at a minimum follow-up of 23 years. There were 40 female patients (44 hips) and 33 male patients (38 hips).

Results

All acetabular and femoral components were well fixed and showed signs of bone ingrowth. Nine acetabular components were revised due to wear-osteolysis-related problems and four due to late dislocation. The probability of not having component revision at 25 years was 83.2% (95% confidence interval (CI) 74.5 to 91.8; number at risk 41). Acetabular osteolysis was observed in ten hips. The mean femoral head penetration was 1.52 mm (sd 0.8) at 15 years and 1.92 mm (sd 1.2) at 25 years. Receiver operating characteristic (ROC) analysis revealed that mean femoral penetration with a value of 0.11 mm/year or more was associated with the appearance of osteolysis. The 25-year Kaplan–Meier survival with different endpoints was 89.9% for acetabular osteolysis (95% CI 83.3 to 96.5), 92.1% for proximal femoral osteolysis (95% CI 86.1 to 98.2), and 75.5% for femoral osteopenia (95% CI 66.5 to 84.5).

Conclusion

The Duraloc-Profile THA system showed excellent long-term bone fixation. Nevertheless, monitoring is recommended in order to detect wear and late dislocations in this population that was relatively young at the time of surgery. Cite this article: Bone Joint J 2019;101-B:378–385.

Evaluation and Treatment of Patients With Acetabular Osteolysis After Total Hip Arthroplasty

As the demand for total hip arthroplasty (THA) continues to increase, the burden of revision THA is also expected to increase. Although the quality of polyethylene has improved markedly, osteolysis continues to be a risk for older designs and younger, active patients. Although progressive but typically asymptomatic in early stages, osteolysis can result in component failure and complicate revision surgery. Serial radiographs are paramount for monitoring progression. Although select cases may be treated with observation, surgery should be considered based on age, activity level, and projected life span. Well-fixed, noncemented modular acetabular components may be treated with curettage and bone grafting, as well as having to bear liner exchange with retention of the acetabular shell. However, in the setting of osteolysis, it is controversial whether bone grafting and component retention is superior to cup revision. This review explores the pathophysiology of osteolysis after THA and provides a comprehensive analysis of the evaluation and treatment of patients with osteolysis.

Longitudinal morphological change of acetabular subchondral bone cyst after total hip arthroplasty in developmental dysplasia of the hip

PURPOSE

The purpose of this study is to clarify morphological changes of acetabular subchondral bone cyst after total hip arthroplasty for osteoarthritis secondary to developmental dysplasia of the hip.

METHODS

Two hundred and sixty-one primary cementless total hip arthroplasties of 208 patients, 18 males, 190 females, were retrospectively reviewed. Morphological changes of subchondral bone cyst were evaluated by computed tomography (CT). The mean cross-sectional area of the cyst from CT scans at 3 months postoperatively and after 7-10 years (average 8.4 years) were compared.

RESULTS

Acetabular subchondral bone cysts were found in 49.0% of all cases in preoperative CT scans. There was no cyst which was newly recognized in CT scan performed after postoperative 7-10 years. All the cross-sectional areas of the cysts evaluated in this study were reduced postoperatively.

CONCLUSIONS

This study revealed that acetabular subchondral bone cysts do not increase or expand after total hip arthroplasty and indicated that the longitudinal morphological change of acetabular bone cysts in patients of developmental dysplasia of the hip do not influence long-term implant fixation in total hip arthroplasty.

Survivorship of Total Hip Joint Replacements Following Isolated Liner Exchange for Wear

BACKGROUND

Liner exchange for articular component wear in total hip joint replacements (THJRs) is a common procedure, often thought to be benign with reliable outcomes. Recent studies, however, suggest high failure rates of liner exchange revisions with significant complications. The primary aim of this study was, therefore, to analyze the survivorship of isolated liner exchange for articular component wear, and secondarily to assess the influence of patient demographics (gender, age, and American Society of Anaesthesiologists [ASA] ratings) on rerevisions following isolated liner exchange for wear.

METHODS

A retrospective review of the 15-year New Zealand Joint Registry (1999-2014) was performed, analyzing the outcomes of isolated liner exchange for articular component wear. The survivorship as defined as rerevision with component exchange was determined and 10-year Kaplan-Meier survivorship curves were constructed. These revision rates were compared to age, gender, and ASA rating groups using a log-rank test.

RESULTS

The 10-year survivorship of THJR following liner exchange revision for liner wear was 75.3%. If a rerevision was required, the median time to rerevision was 1.33 years with a rerevision rate of 3.33 per 100 component years (95% confidence interval 2.68-4.08/100 component years). The principle reasons for rerevision were dislocation (48.4%) and acetabular component loosening (20.9%). There was no statistically significant difference in rerevision rates based on gender, age categories, or ASA scores.

CONCLUSION

THJR isolated liner exchange for liner wear is not a benign procedure with a survivorship of 75.3% at 10 years. Surgeons contemplating liner exchange revisions should be cognisant of this risk and should adequately assess component position and stability preoperatively.

Radiographic scoring system for the evaluation of stability of cementless acetabular components in the presence of osteolysis

AIMS

The stability of cementless acetabular components is an important factor for surgical planning in the treatment of patients with pelvic osteolysis after total hip arthroplasty (THA). However, the methods for determining the stability of the acetabular component from pre-operative radiographs remain controversial. Our aim was to develop a scoring system to help in the assessment of the stability of the acetabular component under these circumstances.

PATIENTS AND METHODS

The new scoring system is based on the mechanism of failure of these components and the location of the osteolytic lesion, according to the DeLee and Charnley classification. Each zone is evaluated and scored separately. The sum of the individual scores from the three zones is reported as a total score with a maximum of 10 points. The study involved 96 revision procedures which were undertaken for wear or osteolysis in 91 patients between July 2002 and December 2012. Pre-operative anteroposterior pelvic radiographs and Judet views were reviewed. The stability of the acetabular component was confirmed intra-operatively.

RESULTS

Intra-operatively, it was found that 64 components were well-fixed and 32 were loose. Mean total scores in the well-fixed and loose components were 2.9 (0 to 7) and 7.2 (1 to 10), respectively (p < 0.001). In hips with a low score (0 to 2), the component was only loose in one of 33 hips (3%). The incidence of loosening increased with increasing scores: in those with scores of 3 and 4, two of 19 components (10.5%) were loose; in hips with scores of 5 and 6, eight of 19 components (44.5%) were loose; in hips with scores of 7 or 8, 13 of 17 components (70.6%) were loose; and for hips with scores of 9 and 10, nine of nine components (100%) were loose. Receiver-operating-characteristic curve analysis demonstrated very good accuracy (area under the curve = 0.90, p < 0.001). The optimal cutoff point was a score of ≥ 5 with a sensitivity of 0.79, and a specificity of 0.87.

CONCLUSION

There was a strong correlation between the scoring system and the probability of loosening of a cementless acetabular component. This scoring system provides a clinically useful tool for pre-operative planning, and the evaluation of the outcome of revision surgery for patients with loosening of a cementless acetabular component in the presence of osteolysis. Cite this article: Bone Joint J 2017;99-B:601-6.

Raman spectroscopy of biomedical polyethylenes

With the development of three-dimensional Raman algorithms for local mapping of oxidation and plastic strain, and the ability to resolve molecular orientation patterns with microscopic spatial resolution, there is an opportunity to re-examine many of the foundations on which our understanding of biomedical grade ultra-high molecular weight polyethylenes (UHMWPEs) are based. By implementing polarized Raman spectroscopy into an automatized tool with an improved precision in non-destructively resolving Euler angles, oxidation levels, and microscopic strain, we become capable to make accurate and traceable measurements of the in vitro and in vivo tribological responses of a variety of commercially available UHMWPE bearings for artificial hip and knee joints. In this paper, we first review the foundations and the main algorithms for Raman analyses of oxidation and strain of biomedical polyethylene. Then, we critically re-examine a large body of Raman data previously collected on different polyethylene joint components after in vitro testing or in vivo service, in order to shed new light on an area of particular importance to joint orthopedics: the microscopic nature of UHMWPE surface degradation in the human body. A complex scenario of physical chemistry appears from the Raman analyses, which highlights the importance of molecular-scale phenomena besides mere microstructural changes. The availability of the Raman microscopic probe for visualizing oxidation patterns unveiled striking findings related to the chemical contribution to wear degradation: chain-breaking and subsequent formation of carboxylic acid sites preferentially occur in correspondence of third-phase regions, and they are triggered by emission of dehydroxylated oxygen from ceramic oxide counterparts. These findings profoundly differ from more popular (and simplistic) notions of mechanistic tribology adopted in analyzing joint simulator data. Statement of Significance This review was dedicated to the theoretical and experimental evaluation of the commercially available biomedical polyethylene samples by Raman spectroscopy with regard to their molecular textures, oxidative patterns, and plastic strain at the microscopic level in the three dimensions of the Euclidean space. The main achievements could be listed, as follow: (i) visualization of molecular patterns at the surface of UHMWPE bearings operating against metallic components; (ii) differentiation between wear and creep deformation in retrievals; (iii) non-destructive mapping of oxidative patterns; and, (iv) the clarification of chemical interactions between oxide/non-oxide ceramic heads and advanced UHMWPE liners.

Survival of uncemented cups from a single manufacturer implanted from 1985 to 2013: Finnish Arthroplasty Register data

INTRODUCTION

Total hip arthroplasty (THA) with uncemented implants has been a relatively common procedure in Finland during the recent decades. The most common brand of uncemented implants was chosen for further analysis to study the survivorship of this uncemented cup design in comparison to cemented references.

PATIENTS, MATERIALS AND METHODS

Since 1980, The Finnish Arthroplasty Register has collected information on THAs on a national level. This study was based on information of THAs recorded in the Finnish Arthroplasty Register from 1985 to 2013. If patient had undergone bilateral THA, only the first one was included. Altogether, 49,289 THAs were included.

RESULTS

The overall 10-year implant survivorship of uncemented implants was 84.3% (95% CI 83.5-85.0%) and of cemented implants 90.6% (90.2-90.0%). The 10-year survival of the contemporary uncemented implants was 90.8% (94.0-95.5%) and 88.5% (84.2-91.7%). The most recently introduced uncemented cup designs had good survivorship rates at 5 years; 10-year survival data are not yet available.

CONCLUSIONS

We found that modern uncemented cup designs may provide good long-term survivorship rates comparable with the gold standard of cemented cups. However, polyethylene wear, liner problems and periosthetic osteolysis may still occur, also with modern uncemented acetabular components.

Comparison of wear rate and osteolysis between annealed and remelted highly cross-linked polyethylene in total hip arthroplasty. A case control study at 7 to 10 years follow-up

BACKGROUND

Low polyethylene wear rate and low incidence of osteolysis after total hip arthroplasty using annealed and remelted highly cross-linked polyethylene have been reported. However, there is no previous report that directly compared both types of highly cross-linked polyethylene. We therefore performed a retrospective study on a series of highly cross-linked polyethylene, in order to: (1) compare wear rates and the incidence of osteolysis between annealed and remelted highly cross-linked polyethylene at 7-10 years; (2) identify the frequency of complication related to annealed and remelted highly cross-linked polyethylene.

HYPOTHESIS

There is no difference in the linear wear rate and the incidence of osteolysis between the annealed and remelted highly cross-linked polyethylene in total hip arthroplasty.

PATIENTS AND METHODS

Two hundred and sixteen cases of cementless total hip arthroplasties with annealed or remelted highly cross-linked polyethylene, which were performed between January 2003 and December 2006 in one institution, were followed for 7-10 years and received computed tomography scan, in addition to radiography at the latest follow-up. Annealed and remelted highly cross-linked polyethylene was used in 91 cases and 125 cases, respectively. A 26-mm cobalt-chromium head was used in all cases. Penetration rates from 1 year to the last evaluation were used to estimate the yearly linear wear rate. Existence of osteolysis was evaluated by plain radiography and computed tomography.

RESULTS

There were no significant differences in patients' background between the two groups. The linear wear rate of annealed and remelted group was 0.031±0.022mm/year and 0.032±0.020mm/year, respectively (P=0.91). Two cases of small femoral osteolysis were found in the annealed group. Any complication related to highly cross-linked polyethylene was not found in both groups.

DISCUSSION

There was no significant difference in the linear wear rate and the incidence of osteolysis between the annealed and remelted group at postoperative 7 to 10 years. Excellent results of both types of highly cross-linked polyethylene were revealed by this study.

LEVEL OF EVIDENCE

Level III retrospective case control study.

How are those “lost to follow-up” patients really doing? A compliance comparison in arthroplasty patients

AIM: To determine whether there is a functional difference between patients who actively follow-up in the office (OFU) and those who are non-compliant with office follow-up visits (NFU).

METHODS: We reviewed a consecutive group of 588 patients, who had undergone total joint arthroplasty (TJA), for compliance and functional outcomes at one to two years post-operatively. All patients were given verbal instructions by the primary surgeon to return at one year for routine follow-up visits. Patients that were compliant with the instructions at one year were placed in the OFU cohort, while those who were non-compliant were placed in the NFU cohort. Survey mailings and telephone interviews were utilized to obtain complete follow-up for the cohort. A χ² test and an unpaired t test were used for comparison of baseline characteristics. Analysis of covariance was used to compare the mean clinical outcomes after controlling for confounding variables.

RESULTS: Complete follow-up data was collected on 554 of the 588 total patients (93%), with 75.5% of patients assigned to the OFU cohort and 24.5% assigned to the NFU cohort. We found significant differences between the cohorts with the OFU group having a higher mean age (P = 0.026) and a greater proportion of females (P = 0.041). No significant differences were found in either the SF12 or WOMAC scores at baseline or at 12 mo postoperative.

CONCLUSION: Patients who are compliant to routine follow-up visits at one to two years post-operation do not experience better patient reported outcomes than those that are non-compliant. Additionally, after TJA, older women are more likely to be compliant in following surgeon instructions with regard to follow-up office care.

Outcomes of post-operative periprosthetic acetabular fracture around total hip arthroplasty

Post-operative periprosthetic acetabular fractures are rare, but serious complication following total hip arthroplasty (THA). As the number of THA performed each year increases so will the expected number of periprosthetic fractures, thus making the treatment of these fractures an important topic for discussion. The purpose of this review is to analyze the recent evidence on risk factors, fracture classification schemes and treatment strategies that have been used for periprosthetic acetabular fractures around THA. The modified Paprosky classification is the most widely used and is a useful guide for management strategies. This classification system provides the guidelines for developing multiple treatment algorithms for decision making. Treatment options for surgical management include open reduction and internal fixation with plating, use of reconstruction cages, trabecular metal augments and bone grafting as needed. Treatment decisions are still an area of controversy and current research.

Cemented liner exchange with bone grafting halts the progression of periacetabular osteolysis

The aims of this were to examine the effect of acetabular liner exchange and intra-operative bone grafting surgery on peri-prosthetic osteolysis. Seven patients with well-fixed Harris-Galante-1 acetabular components received cemented exchange liners for worn liners associated with pre-operatively CT-quantified osteolysis. During surgery, accessible osteolytic lesions were debrided and bone-grafted. Except for one patient with recurrent dislocation and acetabular component revision, the other patients had CT scans at a median of 4 months and at approximately 4 years after surgery. None of the pre-operative lesions increased in volume during the post-operative reporting period and no new lesions were detected. These results show that cemented liner exchange surgery can halt the progression of osteolysis and that bone grafting has the potential to restore bone.

Characterization of progression of pelvic osteolysis after cementless total hip arthroplasty: computed tomographic study

A retrospective analysis of 63 primary total hip arthroplasty cases was done using repeated computed tomography scans to evaluate the pelvic osteolytic lesions in early stage. The progression rate of osteolysis of hips with small osteolytic volume less than 766.97 mm(3) in initial CT was 85.82 mm(3)/year, and that of hips with osteolysis more than 766.97 mm(3) was 456.3 mm(3)/year (P < 0.001). Younger patients less than 52 years old with good Harris Hip Scores (more than 80) frequently showed much faster progression in volume of osteolytic lesions. The rate of osteolysis was accelerated when the amount of osteolysis reached a certain threshold volume in active young patients in a cascade manner even in early stage.

Effect of component design in retrieved bipolar hip hemiarthroplasty systems

Primary articulation of bipolar hemiarthroplasty systems is at the femoral head-liner interface. The purpose of this study was to compare observed damage modes on 36 retrieved bipolar systems with implant, demographic, intraoperative, and radiographic data to elucidate the effects of component design, specifically locking mechanism, on clinical performance. Retrieved bipolar hip hemiarthroplasty systems of 3 different design types were obtained, disassembled, and evaluated macro- and microscopically for varying modes of wear, including abrasion, burnishing, embedding, scratching, and pitting. Clinical record review and radiographic analysis were performed by a senior orthopedic surgery resident. Average bipolar hip hemiarthroplasty system term of service was 46 months (range, 0.27-187 months). All devices contained wear debris captured within the articulating space between the femoral head and liner. In 31% of patients without infection, lucency was observed on immediate prerevision radiographs. The system with a leaf locking mechanism showed significantly increased radiographically observed osteolysis (P=.03) compared with a system with a stopper ring locking mechanism. In addition, implant design and observed damage modes, including pitting and third-body particle embedding, were significantly associated with radiographically observed osteolysis.

Does computed tomography add information on radiographic analysis in detecting periprosthetic osteolysis after total ankle arthroplasty?

BACKGROUND

The major longer term complications of ankle arthroplasty are periprosthetic osteolysis and aseptic loosening. Follow-up studies of total hip arthroplasties show that measurements of periprosthetic osteolytic lesions on radiographs underestimate the size compared with those made on computed tomography (CT), and some of the lesions may even remain undetected on radiographs. However, it is unclear whether the same applies to total ankle arthroplasty (TAA).

METHODS

We retrospectively reviewed the radiographs of 123 patients who had undergone TAA with the Ankle Evolutive System (AES) implant. Of these, 43 (34.9%) had at least 1 large (greater than 10 mm) osteolytic lesion on radiographs at a minimum follow-up of 14 months (mean, 43.1 months; range, 14-85 months). Forty of the 43 patients underwent helical CT imaging.

RESULTS

Computed tomography showed more osteolytic lesions than radiographs around both tibial and talar components. CT also showed larger lesions than radiographs in 9 of 10 zones around prosthetic components. The difference was highly significant in 3 zones around the talar component.

CONCLUSION

Computed tomography showed more and larger periprosthetic lesions than radiographs around an ankle prosthesis. Because osteolysis is progressive in nature, it presumably leads to component failure. Considering our results, we recommend adding CT imaging to postoperative follow-up after TAA for patients with suspected or known periprosthetic lucencies on radiographs.

LEVEL OF EVIDENCE

Level III, diagnostic study.

Progression of periacetabular osteolytic lesions

BACKGROUND

The development of three-dimensional computed tomography (CT) imaging techniques has enabled the detection, accurate measurement, and monitoring of periprosthetic osteolytic lesions. The aim of this study was to track the progression in size of osteolytic lesions and to determine those factors that are associated with the risk of progression. A secondary aim was to investigate whether progression in size of osteolytic lesions could be monitored with use of radiographs.

METHODS

We retrospectively determined, with use of sequential CT scans, the progression of periacetabular osteolysis over a period of as much as nine years in a cohort of twenty-six patients (thirty acetabular components) in whom the cementless acetabular component or components had been in place for longer than ten years at the time of the initial CT scan. High-resolution CT scans with metal-artifact suppression were used to determine the volume of osteolytic lesions. Progression in the size of osteolytic lesions per year was calculated as the change in the volume of osteolytic lesions between serial CT scans. Associations were determined between the progression in size of osteolytic lesions, osteolysis rate at the initial CT, patient age, sex, walking limitations, and activity level. Progression in size of osteolytic lesions as determined with use of CT was compared with that determined with use of radiographs.

RESULTS

Mean progression in the size of osteolytic lesions, as determined with use of CT, was 1.5 cm(3)/yr (range, 0 to 7.5 cm(3)/yr). The amount of osteolysis at the initial CT scan and patient activity were good predictors of osteolytic lesion progression. The strongest predictor of osteolytic lesion progression occurred when these two risk factors were combined (p = 0.0019). The value of radiographs was limited to monitoring of larger lesions identified by CT.

CONCLUSIONS

This is the first study to report on the progression of osteolysis adjacent to cementless acetabular components from medium to long-term follow-up. The data suggest that the osteolysis rate at the initial CT and patient activity can be useful factors in predicting the progression in size of periacetabular osteolytic lesions.

Retention of a well-fixed acetabular component in the setting of acetabular osteolysis

PURPOSE

The treatment strategy for pelvic osteolysis with a well-fixed acetabular component after total hip arthroplasty(THA) involves replacing the acetabular cup liner and femoral head, débriding osteolytic lesions, and grafting.

METHODS

We investigated whether retention of a well-fixed acetabular component using the two-approach technique—the ilioinguinal approach combined with the posterolateral approach—was compatible with socket survival. Were viewed clinical and radiographic findings for 24 patients(24 hips) who had undergone acetabular revision arthroplasty of a well-fixed socket for progressive osteolysis. The surgical techniques used included osteolytic lesion débridement and bone grafting through the ilioinguinal approach,and replacement of the acetabular liner and femoral head through the posterolateral approach.

RESULTS

The mean duration of follow-up after revision was 2.3 (range 2.1–3.9) years. At follow-up evaluation, all acetabular components were well fixed and showed no evidence of loosening, osseous integration was apparent and there was no radiographic evidence that any lesions had progressed. No new osteolytic lesions were identified, and there were no clinical or radiographic complications.

CONCLUSIONS

Curettage and bone grafting under direct vision, cup liner and femoral-head replacement because of progressive retroacetabular osteolysis and retention of well fixed components using the two-approach technique results in good osseous integration of lysis. Larger studies with longer follow-up periods are required to establish the longterm success of this technique.

The Ringloc liner compared with the Hexloc liner in total hip arthroplasty

The aim of this study was to compare the 10-year survival rate, pelvic osteolysis frequency and linear head penetration rate of the Hexloc and Ringloc liners used together with a partially threaded porous and hydroxyapatite coated cup and the Bi-Metric uncemented femoral stem. The 15-year results for the cup with the Hexloc liner are also reported. We included 332 consecutive hips (166 Hexloc and 166 Ringloc) on 281 patients in the study. Revisions of prosthesis components were recorded and pelvic osteolytic lesions were assessed using radiographs and computed tomography. The linear head penetration rate was measured using the Martell method. The 10-year survival rate of the liner with revision due to liner wear and/or osteolysis as endpoint was 88% for the Hexloc liner and 98% for the Ringloc liner. The 15-year survival rate of the Hexloc liner was 67%. Pelvic osteolysis was found in 27% of the Hexloc and 19% of the Ringloc hips. After 15 years, 53% of the Hexloc hips had developed an osteolytic lesion. The linear head penetration rate was 0.16 mm/year for the Hexloc liner and 0.12 mm/year for the Ringloc liner. This paper is the first to describe the rapidly deteriorating survival up to 15 years with the old generation gamma-in-air sterilized polyethylene used in Hexloc liners. The newer Ringloc liner with the ArCom™ polyethylene has superior clinical results but a linear wear rate and frequency of osteolytic lesions that is higher than expected.

Management of acetabular bone loss in revision total hip arthroplasty

Most acetabular revisions can be managed with a hemispherical component with screw fixation. Areas of segmental bone loss that preclude acetabular component stability may be managed with structural allograft or second-generation porous metal augments. Acetabular cages have a limited application but can be a useful tool in the management of massive bone loss and pelvic discontinuity.

Silent soft tissue pathology is common with a modern metal-on-metal hip arthroplasty

BACKGROUND AND PURPOSE

Adverse reactions to metal debris have been reported to be a cause of pain in metal-on-metal hip arthroplasty. We assessed the incidence of both symptomatic and asymptomatic adverse reactions in a consecutive series of patients with a modern large-head metal-on-metal hip arthroplasty.

METHODS

We studied the early clinical results and results of routine metal artifact-reduction MRI screening in a series of 79 large-head metal-on-metal hip arthroplasties (ASR; DePuy, Leeds, UK) in 68 patients. 75 hips were MRI scanned at mean 31 (12-52) months after surgery.

RESULTS

27 of 75 hips had MRI-detected metal debris-related abnormalities, of which 5 were mild, 18 moderate, and 4 severe. 8 of these hips have been revised, 6 of which were revised for an adverse reaction to metal debris, diagnosed preoperatively with MRI and confirmed histologically. The mean Oxford hip score (OHS) for the whole cohort was 21. It was mean 23 for patients with no MRI-based evidence of adverse reactions and 19 for those with adverse reactions detected by MRI. 6 of 12 patients with a best possible OHS of 12 had MRI-based evidence of an adverse reaction.

INTERPRETATION

We have found a high early revision rate with a modern, large-head metal-on-metal hip arthroplasty. MRI-detected adverse rections to metal debris was common and often clinically "silent". We recommend that patients with this implant should be closely followed up and undergo routine metal artifact-reduction MRI screening.

Early reactive synovitis and osteolysis after total hip arthroplasty

BACKGROUND

Little is known about intraarticular pathology following THA prior to the radiographic appearance of osteolysis, primarily due to imaging limitations. MRI has recently been applied to imaging the postarthroplasty hip with the ability to detect periarticular bony and soft tissue pathology; specifically, it is able to detect abnormal synovial patterns and focal bone loss well before the radiographic appearance of osteolysis.

QUESTIONS/PURPOSES

We therefore used MRI to determine the incidence of early reactive synovitis and osteolysis in asymptomatic patients after THA, and whether there is an association between these MRI findings and clinical outcomes or radiographic wear measurements at this early stage.

METHODS

We recruited 31 patients (33 hips) who underwent routine noncemented THA with one of three types of bearing surfaces: metal-on-cross-linked polyethylene (n = 7), ceramic-on-ceramic (n = 12), and ceramic-on-cross-linked polyethylene (n = 14). Patients underwent specialized MRI at a minimum of 12 months (mean, 23 months; range, 12-37 months) after surgery. MR images were analyzed for the presence of synovitis or osteolysis. WOMAC scores, patient assessment questionnaires, and radiographic wear measurements were correlated with MRI findings.

RESULTS

Reactive synovitis was observed in 13 of 33 patients (39%) and focal osteolysis in one of 33 (3%). The presence of synovitis did not correlate with pain, activity level, patient satisfaction or clinical outcome scales, nor did it correlate with radiographic wear measurements at early followup.

CONCLUSIONS

Our observations suggest reactive synovitis is common yet asymptomatic at short-term followup. We do not know either the etiology or the long-term implications of these observations.

Use of morphometry to quantify osteolysis after total hip arthroplasty

BACKGROUND

Progressive osteolysis threatens the longevity of hip arthroplasties and radiographic review is recommended. Measurement of osteolytic lesions in a clinical setting has not been achieved easily in the past. Other radiologic investigations provide accurate information but cost and risk to the patient prohibit their use in routine review.

QUESTIONS/PURPOSES

We developed a simple, reliable tool to be used in hip arthroplasty review to quantify osteolytic changes seen on plain film radiographs.

METHODS

A morphometric grid was developed and tested on simulated and actual osteolytic lesions. Four health professionals measured lesions on each of two occasions. Intraclass correlation coefficients (ICC) for interobserver and intraobserver reliabilities were calculated and Bland-Altman plots were constructed for graphic analysis.

RESULTS

The ICCs for interobserver reliability on the simulated and actual osteolytic lesions were in the range 0.90 to 0.96. The values for intraobserver (test-retest) reliability were 0.97 to 0.98. The Bland-Altman plots confirmed agreement and in each case, proximity of the mean to zero indicated no significant bias.

CONCLUSIONS

The data show a morphometric grid is reliable for measuring osteolytic changes after hip arthroplasty.

CLINICAL RELEVANCE

This tool has potential to improve monitoring processes for hip arthroplasty and to be useful in future research studies. Additional work is needed to test for validity and clinical importance of the measurements obtained.

Relationship between the pelvic osteolytic volume on computed tomography and clinical outcome in patients with cementless acetabular components

The purpose of this study was to evaluate the relationship between the pelvic osteolytic volume on computed tomography (CT) and clinical outcome in patients with cementless acetabular components. We reviewed 87 patients (104 hips) who met the following inclusion criteria: (1) there was evidence of pelvic osteolysis on CT at a minium of five years postoperatively, (2) all cups and stems were radiographically stable at the time of CT, (3) the follow-up period after CT was a minimum of two years clinically. The mean pelvic osteolytic volume was 2.3 ± 6.9 cm(3). The mean Harris hip score (HHS) at CT was 92.3 ± 7.9 points. Inversely moderate correlation (r = -0.569, P < 0.05) was found between the HHS at CT and pelvic osteolytic volume. In ten cases of hips with acetabular revisions, the mean pelvic osteolytic volume was 16.3 ± 26.9 cm(3). The mean HHS at CT and HHS at reoperation was 87.6 ± 9.2 points and 73.4 ± 8.8 points, respectively, with significant difference (P < 0.05). The area under curve (ROC) analysis showed that the optimal cutoff value of the osteolytic volume was 4.8 cm(3) with 100% each for sensitivity and specificity. We conclude that the amount of pelvic osteolytic volume on CT may be used to guide treatment decision-making in patients with well-fixed cementless acetabular components who show evidence of pelvic osteolysis.

Revision hip arthroplasty for ceramic-on-ceramic squeaking hips does not compromise the results

Squeaking is a complication that may occur after ceramic-on-ceramic total hip arthroplasty (THA) that can be intolerable enough for some patients to seek revision THA. This prospective case series of 11 hips is the first to report on the results of these patients. All patients underwent isolated head and liner exchange to a metal-on-highly cross-linked polyethylene using the direct lateral approach. Mean age was 45.5 years, and body mass index was 30.0 kg/m(2). Hips were revised at an average of 40.1 months postindex THA. Retrieval analysis showed 7 of 7 liners/heads with edge loading wear and 5 of 7 liners with signs of neck-rim impingement. Short Form-36 mental dimension, Western Ontario McMaster Osteoarthritis Index, and Harris Hip Score (HHS) showed a statistically significant improvement (P < .05). All squeaking was eliminated after revision THA. There were no morbidities or complications after the revision surgery rendering isolated head-and-liner exchange to a metal-on-highly cross-linked polyethylene a relatively benign procedure.

Raman tensor analysis of ultra-high molecular weight polyethylene and its application to study retrieved hip joint components

The angular dependences of the polarized Raman intensity of A(g), B(1g), B(2g), and B(3g) modes have been preliminary investigated on a model fiber sample of ultra-high molecular weight polyethylene (UHMWPE) in order to retrieve the Raman tensor elements, i.e. the intrinsic parameters governing the vibrational behavior of the orthorhombic structure of polyethylene. Based on this Raman analysis, a method is proposed for determining unknown crystallographic orientation patterns in UHMWPE biomedical components concurrently with the orientation distribution functions for orthorhombic lamellae. An application of the method is shown, in which we quantitatively examined the molecular orientation patterns developed on the surface of four in vivo exposed UHMWPE acetabular cups vs. an unused cup. Interesting findings were: (i) a clear bimodal distribution of orientation angles was observed on worn surfaces; and (ii) a definite and systematic increase in both molecular orientation and crystallinity in main wear zones vs. non-wear zones was found in all retrieved acetabular cups. The present crystallographic analysis is an extension of our previous Raman studies of UHMWPE acetabular cups related to assessments of oxidation and residual strain and suggests a viable path to track back wear-history information from the surface of UHMWPE, thus unfolding the in vivo kinematics of the bearing surfaces in hip joints on the microscopic scale.

A three-dimensional method for evaluating changes in acetabular osteolytic lesions in response to treatment

The treatment of asymptomatic osteolysis among well-fixed cementless cups remains controversial. To compare the effectiveness of different treatment strategies, an objective technique for evaluating bone remodeling would be useful. By matching and comparing serial CT images with the aid of a computer-assisted imaging program, we developed a method to evaluate three-dimensional mineralization changes within osteolytic defects. Preoperative, immediate postoperative, and followup CT images were normalized based on a phantom with known densities and matched using image registration so that the same region could be analyzed on each image. New bone mineralization within the preoperative osteolytic lesion volume was quantified based on a patient-specific trabecular bone density threshold. As a pilot study, we applied this technique in 10 patients treated by polyethylene liner exchange with débridement and grafting of periacetabular osteolytic lesions using a calcium sulfate bone graft substitute. Relative to the preoperative osteolytic lesion volume, an average of 43% (range, 8%-72%) of each defect was filled with graft at revision. After resorption of the graft, an average of 24% (range, 9%-44%) of the original defect volume demonstrated evidence of new mineralization at 1-year followup. The amount of new mineralization was directly proportional (r(2) = 0.70) to the defect filling achieved at revision. CT-based image analysis offers an objective method for quantifying three-dimensional bone remodeling and can be used to evaluate the effectiveness of osteolysis treatment strategies.

LEVEL OF EVIDENCE

Level IV, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.

Third-generation ceramic-on-ceramic bearing surfaces in revision total hip arthroplasty

With an increase of revision total hip arthroplasty (THA), the choice of bearing surface becomes more important. Wear debris by conventional metal-on-polyethylene articulations may cause extensive osteolysis, especially in young patients. We analyzed the clinical and radiographic outcomes after revision THA using third-generation ceramic-on-ceramic bearing surfaces in 42 hips. The mean age of the patients was 48.8 years (32-59 years), and the mean duration of follow-up monitoring was 5.4 years (3.2-8.0 years). At final follow-up examination, the average Harris Hip Score was 91.3. Although minor complications were observed in 6 hips (14.3%), no hips required additional revision surgery. No hip showed radiolucent lines, acetabular cup migration, or osteolysis. Our data show that clinical and radiographic outcomes after revision THA using third-generation ceramic-on-ceramic bearing surfaces are favorable. Ceramic-on-ceramic bearing surfaces can be preferentially considered for revision THA, especially in young patients. Further studies with long-term follow-up data are warranted.

Biomechanical modeling of acetabular component polyethylene stresses, fracture risk, and wear rate following press-fit implantation

Press-fit implantation may result in acetabular component deformation between the ischial-ilial columns ("pinching"). The biomechanical and clinical consequences of liner pinching due to press-fit implantation have not been well studied. We compared the effects of pinching on the polyethylene fracture risk, potential wear rate, and stresses for two different thickness liners using computational methods. Line-to-line ("no pinch") reaming and 2 mm underreaming press fit ("pinch") conditions were examined for Trident cups with X3 polyethylene liner wall thicknesses of 5.9 mm (36E) and 3.8 mm (40E). Press-fit cup deformations were measured from a foam block configuration. A hybrid material model, calibrated to experimentally determined stress-strain behavior of sequentially annealed polyethylene, was applied to the computational model. Molecular chain stretch did not exceed the fracture threshold in any cases. Nominal shell pinch of 0.28 mm was estimated to increase the volumetric wear rate by 70% for both cups and peak contact stresses by 140 and 170% for the 5.9 and 3.8 mm-thick liners, respectively. Although pinching increases liner stresses, polyethylene fracture is highly unlikely, and the volumetric wear rates are likely to be low compared to conventional polyethylene.

Pelvic osteolysis relationship to radiographs and polyethylene wear

The relationship of radiographic pelvic osteolysis to computed tomographic (CT) volume and polyethylene wear remains controversial. We evaluated the sensitivity and specificity of radiographs in detecting osteolysis considering CT scan as the true value, in 118 hips with cementless cups. Correlation between osteolysis volume in CT, area of osteolysis in radiograph, and linear wear of polyethylene was assessed. The sensitivity and specificity of anteroposterior radiographs for detection of osteolysis was 57.6% and 92.9%, respectively. Addition of oblique radiographs increased the sensitivity to 64.4% without changing the specificity. The sensitivity increased to 92.8% for lesion more than 1000 mm(3). There was good correlation between 2-dimensional (2D) osteolytic area in radiograph and 3-dimensional (3D) volume (r = 0.74) in CT scan and linear wear of polyethylene showed good correlation with 3D CT volume (r = 0.62) and 2D area in radiograph (r = 0.60). Thus radiographs are useful to screen clinically significant osteolysis.

Isolated polyethylene exchange versus acetabular revision for polyethylene wear

Polyethylene wear and osteolysis are not uncommon in THA mid- and long-term. In asymptomatic patients the dilemma faced by the orthopaedic surgeon is whether to revise the cup and risk damage to the supporting columns and even pelvic discontinuity or to perform isolated polyethylene exchange and risk a high rate of postoperative recurrent instability and dislocation that will necessitate further surgery. We retrospectively reviewed 62 patients (67 hips) who underwent revision arthroplasty for polywear and osteolysis. Thirty-six hips had isolated polyethylene exchange, while 31 had full acetabular revision. The minimum followup was 2 years (mean, 2.8 years; range, 2-5 years). Three of 36 hips with a retained cup grafted through the cup holes failed within 5 years due to acetabular loosening. One of 31 hips with full revision underwent re-revision for aseptic cup loosening at 5 months postoperatively. Although we do not recommend prophylactic revision of all cups for polywear and osteolysis, the patient may be warned of the possibility of an approximate 10% failure rate when retaining the acetabular component. We do, however, advocate cup extraction in the following situations: damage to the locking mechanism, erosion of the femoral head through the liner and into the cup damaging the metal, and a malpositioned component that may jeopardize the stability of the revision.

LEVEL OF EVIDENCE

Level II, prognostic study. See the Guidelines for Authors for a complete description of levels of evidence.

Retroacetabular osteolytic lesions behind well-fixed prosthetic cups: pilot study of bearings-retaining surgery

Background

Osteolytic lesions are common radiological findings behind acetabular prosthetic cups. If the cup is well-fixed, the management is quite controversial. Although implant exchange is the most reliable procedure, in most cases it could be considered overtreatment, with the potential for further morbidity and bone loss. Liner exchange associated with lesion debridement and grafting represents an alternative option that is less invasive. Here we present our experiences from a small pilot study of minimally invasive osteolysis treatment without bearings exchange in patients with no evidence of liner wear.

Materials and methods

Inclusion criteria: retroacetabular osteolytic lesions in ceramic-on-polyethylene or metal-on-polyethylene cementless total hip arthroplasties, affecting more than 50% of the bone–prosthesis interface on anteroposterior radiography. Exclusion criteria: head penetration into the liner, suspected loosening or infection. Six patients were selected, two asymptomatic and four symptomatic. Only the symptomatic patients accepted the proposed treatment (performed between June 2004 and March 2006). All of them received fluoroscopy-assisted lesion debridement through an iliac cortical window, morcellized bone allograft mixed with autologous platelet-rich plasma, joint exploration for culture and lavage through a small capsular window. Patients were followed up clinically and radiologically at six months, 12 months, and then yearly.

Results

Three patients out of four showed clinical and radiological improvement. One showed radiological improvement only, and recently underwent cup exchange for subsequent loosening. The visual analog scale (VAS) values for pain decreased on average, but not significantly. No major complications occurred. No recurrence was noted at 2.25–4 years’ follow-up.

Conclusions

Although the small series does not allow any absolute conclusions to be drawn, the reported results seem to justify further, wider studies. It is still unclear if osteolytic lesions associated with no wear of the poly liner would progress to implant failure if left untreated. Until the problem is better understood, this procedure might represent an interesting way to prevent potential loosening and severe bone loss in intact sockets.

Computer-assisted technique to delineate osteolytic lesions around the femoral component in total hip arthroplasty

There are currently no ideal quantitative measures assessing osteolysis after total joint arthroplasty. This study reports a new approach for quantification of osteolytic lesions on radiographs of total hip arthroplasty with the hypothesis that computer-assisted lesion quantification improves analysis precision over currently used qualitative visual assessment and thus improves progression monitoring. Duplicate exposure sets of anterior-posterior and frog-leg view radiographs of 15 volunteer total hip arthroplasty patients with radiographically evident periprosthetic lucencies were used. Two independent readers delineated the lesions using on-screen digital marker tools. Based on duplicate readings of the first exposure set only, intraoperator precision had a coefficient of variation (CV) from 1.5% to 3.4%, whereas interoperator precision CV ranged from 3.2% to 4.6%. The reproducibility of the x-ray technique as assessed by single readings of both sets of x-rays was CV 3.2% to 4.8%. The new technique compares favorably to precision of qualitative visual assessment and permits more accurate detection and quantitation of osteolytic lesions.

Isolated acetabular liner exchange

During the past two decades, most total hip arthroplasties were performed with metal or ceramic heads on conventional polyethylene, an articulation associated with wear and limited life expectancy. Wear is associated with acetabular osteolysis. Isolated liner exchange has become a common surgical intervention when the acetabular component remains well-fixed. The purpose of isolated liner exchange is to prevent loosening of the components secondary to osteolysis and catastrophic mechanical failure caused by bearing wear-through. Treatment options for polyethylene wear include observation (in the asymptomatic hip), liner exchange, and more extensive revision procedures. Patients frequently present with asymptomatic but substantial polyethylene wear with or without associated osteolysis, the treatment of which is controversial. Other areas of debate include complete acetabular component removal to allow bone grafting and placement of an improved bearing surface, reuse of modular mechanisms, cementation into well-fixed shells, and whether to use periacetabular bone grafting.

Revision total hip arthroplasty for pelvic osteolysis with well-fixed cementless cup

Treatment of pelvic osteolysis after total hip arthroplasty (THA) remains controversial. Clinical and radiographic outcomes of revision THA were evaluated in 62 hips with pelvic osteolysis and well-fixed cementless cups. The patients' mean age was 50.9 years, and the mean interval from primary to revision THA was 9.7 years. For revision, cementless cups were used in 51 hips, and cemented cups in 11 with acetabular reinforcement rings in 9. The mean duration of follow-up after revision THA was 5.9 years (range, 3.0-9.7 years). At final follow-up, the average Harris Hip Score was 92.4, and there was no radiographic complication except for 1 with change of inclination. Revision THA for pelvic osteolysis with well-fixed cementless cups showed favorable outcomes, and it can be preferentially used in young patients.

Evaluation of periprosthetic lucency after total ankle arthroplasty: helical CT versus conventional radiography

BACKGROUND

Osteolysis after total ankle arthroplasty (TAA) has become a major concern regarding long-term implant survival. The primary goal of this study was to determine whether CT was more sensitive than plain films in detecting the presence and extent of periprosthetic lucency. A secondary goal was to determine whether lack of syndesmotic fusion was associated with more extensive lucency.

METHODS

Seventeen patients (19 ankles) who had TAA between 2001 and 2003 were consecutively recruited and evaluated as part of a prospective study. Plain radiographs and helical CT with metal-artifact minimization were obtained. Evidence of lucent lesions and syndesmotic fusion was compared using the different imaging techniques.

RESULTS

Of the 19 ankles imaged, a total of 29 lesions were detected by CT, whereas plain radiographs detected 18 lesions. CT detected 21 lesions less than 200 mm(2), of which plain radiographs detected only 11. The mean size of the lesions detected on CT was over three times larger than the size on plain radiographs. With the small sample size used, there were no statistically significant differences between ankles with and without fusion of the syndesmosis and the extent (p = 0.84) and location (p = 0.377) of lucency.

CONCLUSION

CT is a more accurate method for early detection and quantification of periprosthetic lucency than plain radiographs. Accurate evaluation of lucent lesions may identify patients at high risk for lack of syndesmotic fusion with subsequent loosening and implant failure.

Separation of the apex hole eliminator screw in four failed hybrid total hip arthroplasties

Advancement or separation of the apex hole eliminator screw in uncemented Duraloc 100 cups (DePuy, Warsaw, Indiana, USA) has been recently reported as a radiographic finding without clinical effects. We report 4 patients with a separation of the apex hole eliminator screw in Duraloc 300 uncemented cups and aseptic failures of a hybrid total hip arthroplasty (acetabular osteolysis and femoral stem loosening). Revision surgery was performed when disabling pain and radiographic signs of loose components were present. Although difficult to determine, a relationship between the screw migration and the failure could have existed in these cases. Migration of the screw might not only be interpreted as a radiographic, clinically irrelevant finding. Its presence should alert the orthopaedic surgeon that the prosthesis is exposed to high intraarticular fluid pressures.

The value of anteroposterior pelvic radiographs for evaluating pelvic osteolysis

We investigated the role of conventional radiographs and computed tomography scans for the routine followup of total hip arthroplasty patients. Among 92 total hip arthroplasties with a mean followup of 8.5 years, 94 acetabular lesions were detected among 63 hips using computed tomography and 42 of these hips had osteolysis diagnosed on radiograph. Using computed tomography as a gold standard, the sensitivity of anteroposterior pelvic radiographs for the detection of acetabular osteolysis was 67% and the specificity was 72%. Although smaller lesions were more frequently missed, osteolysis was diagnosed on radiograph in 20 of 22 total hip arthroplasties with lesion volumes of at least 10 mL. Because larger osteolytic lesions were generally detected on radiograph, two-dimensional and three-dimensional lesion sizes correlated. However, the limits of agreement for the volume estimates based on the radiograph area were -14.6 to 18.7 mL. Although radiographs can be useful to screen for clinically important pelvic osteolysis, computed tomography images are necessary to accurately measure lesion volumes.

What is the role of magnetic resonance imaging in the evaluation of total hip arthroplasty?

MRI has been shown to be an extremely effective instrument in the management of painful hip arthroplasty. Its superior soft tissue contrast and direct multiplanar acquisition compared to computerized tomography (CT) and radiographs allows for reproducible visualization of periacetabular osteolysis, demonstrating compression of neurovascular bundles by extracapsular synovial deposits. In addition, MRI can often elucidate etiology of neuropathy in the perioperative period and is further helpful in evaluating the soft tissue envelope, including the attachment of the hip abductors, short external rotators and iliopsoas tendon. A further advantage of MRI over CT is its lack of ionizing radiation. Most importantly, MRI can disclose intracapsular synovial deposits that precede osteoclastic resorption of bone.

Comparison of CT, MRI, and radiographs in assessing pelvic osteolysis: a cadaveric study

In this study, we compared the accuracy of radiography, computed tomography, and magnetic resonance imaging in assessing periacetabular osteolytic lesions. Using a previously published cadaver model, we created 87 lesions in pelves implanted with total hip replacement components. The sensitivity for detecting lesions was 51.7% for radiography, 74.7% for computed tomography, and 95.4% for magnetic resonance imaging. For all three techniques, sensitivity increased as lesion size increased. Magnetic resonance imaging emerged as the most effective tool for detecting small periacetabular osteolytic lesions (< or = 3 cm). For lesions larger than 3 cm, which are of more concern clinically, computed tomography and magnetic resonance imaging were effective in identifying lesions with detection rates greater than 80%. For radiography and computed tomography, lesion detection was dependent on lesion location, whereas magnetic resonance imaging had consistently good sensitivity in all lesion locations. Although the mean volumetric errors for computed tomography and magnetic resonance imaging (0.3 cm and 0.8 cm) were small compared with mean lesion volume (6.1 cm), computed tomography was more accurate than magnetic resonance imaging at measuring lesion volume, with a lower mean absolute error. This study verifies the problems associated with radiographic detection of osteolysis while showing the effectiveness of computed tomography and magnetic resonance imaging in determining the presence of lesions and assessing their three-dimensional volume.

Magnetic resonance imaging in the evaluation of periprosthetic acetabular osteolysis: a cadaveric study

Periprosthetic osteolysis is a well recognized complication of total hip arthroplasty that leads to implant failure. The ability to accurately assess and visualize the position and volume of periacetabular bone defects is paramount for clinical observation and medical treatment, as well as pre-operative planning of revision surgery. We have developed a modified magnetic resonance imaging (MRI) protocol that is useful in detection and quantification of periacetabular bone loss. The purpose of this study is to compare MRI to plain film analysis in the assessment of periacetabular bone loss using a cadaver model. MRI was 95% sensitive in the detection of lesions. Specificity was 98%, and accuracy was 96%. Lesion detection was not statistically dependent on lesion location (p=0.27). The mean absolute error in determining lesion size was 0.8+/-2.2 cm3. There was a correlation between increasing lesion size and lesion detection (p=0.02, logistic regression). The largest lesion that was missed by MRI analysis measured 2.8 cm3, and all lesions 3.0 cm3 were correctly identified, with a relative error volume measurement of 12.4+/-25.3%. This correlated to an absolute error of 1.4+/-2.4 cm3. Using conventional radiographic analysis, the overall sensitivity of lesion detection was 52%, and the specificity was 96%. Using plain film analysis, identification of true lesions depended on the location with 83% of ilial lesions, 64% of pubic lesions, 55% of ischial lesions, and 0% of posterior wall lesions correctly identified. The modified MRI technique utilized did allow for accurate visualization of simulated osteolytic lesions, and may provide a suitable noninvasive method to provide serial assessment of clinical periacetabular osteolysis without the use of ionizing radiation.

The effect of geometry and abduction angle on the stresses in cemented UHMWPE acetabular cups--finite element simulations and experimental tests

BACKGROUND

Contact pressure of UHMWPE acetabular cup has been shown to correlate with wear in total hip replacement (THR). The aim of the present study was to test the hypotheses that the cup geometry, abduction angle, thickness and clearance can modify the stresses in cemented polyethylene cups.

METHODS

Acetabular cups with different geometries (Link: IP and Lubinus eccentric) were tested cyclically in a simulator at 45 degrees and 60 degrees abduction angles. Finite element (FE) meshes were generated and two additional designs were reconstructed to test the effects of the cup clearance and thickness. Contact pressures at cup-head and cup-cement interfaces were calculated as a function of loading force at 45 degrees, 60 degrees and 80 degrees abduction angles.

RESULTS

At the cup-head interface, IP experienced lower contact pressures than the Lubinus eccentric at low loading forces. However, at higher loading forces, much higher contact pressures were produced on the surface of IP cup. An increase in the abduction angle increased contact pressure in the IP model, but this did not occur to any major extent with the Lubinus eccentric model. At the cup-cement interface, IP experienced lower contact pressures. Increased clearance between cup and head increased contact pressure both at cup-head and cup-cement interfaces, whereas a decreased thickness of polyethylene layer increased contact pressure only at the cup-cement interface. FE results were consistent with experimental tests and acetabular cup deformations.

CONCLUSION

FE analyses showed that geometrical design, thickness and abduction angle of the acetabular cup, as well as the clearance between the cup and head do change significantly the mechanical stresses experienced by a cemented UHMWPE acetabular cup. These factors should be taken into account in future development of THR prostheses. FE technique is a useful tool with which to address these issues.

Computed tomography in the assessment of periacetabular osteolysis

BACKGROUND

Computed tomography recently has been proposed as an accurate method for diagnosing periacetabular osteolytic lesions. Several investigators have attempted to validate the accuracy of this technique, but they employed cadaveric and animal models, which cannot replicate the adaptive changes that occur over time in vivo. This study was performed to determine the accuracy of computed tomography in identifying and measuring periacetabular osteolytic lesions in hemipelves retrieved at autopsies of individuals with a previously well-functioning total hip prosthesis.

METHODS

We evaluated nine hemipelves, retrieved at autopsy, that contained a cementless porous-coated acetabular component. The fresh specimens were examined with conventional radiographs and computed tomography and then were embedded and sectioned into 1.5-mm slices for evaluation with slab radiographs. Anteroposterior and iliac oblique plain radiographs as well as axial, coronal, and sagittal computed tomography scans were reviewed to determine the presence and location of any periacetabular osteolytic lesions. These results were then compared with those identified on the slab radiographs. Lesion volume was calculated from computed tomography scans with use of post-processing software.

RESULTS

A total of twenty-three periacetabular osteolytic lesions were identified on the slab radiographs of the nine hemipelves. The plain radiographs identified twelve (52%) of the twenty-three lesions, and the computed tomography scans identified twenty (87%) of the twenty-three lesions. Three medial wall perforations were identified on the computed tomography scans but were not detected on the plain radiographs. Computed tomography was accurate in measuring the volume of the osteolytic lesions (r(2) = 0.997) but tended to overestimate the volumes measured on the slab radiographs. Periacetabular osteolytic lesions appeared on the computed tomography scans and slab radiographs as areas devoid of trabecular bone that were delineated by a sclerotic border and communicated with the joint space.

CONCLUSIONS

In this autopsy model, computed tomography was an accurate method for detecting the location and measuring the volume of periacetabular osteolytic lesions.

Retroacetabular osteolysis: when to operate?

Polyethylene liner exchange for retroacetabular osteolysis should be done before the shell becomes loose. The purpose of this study was to determine the radiographic quantity of osteolysis that will predict impending loosening of the cementless shell. Between 1992 and 2002, 46 cementless shells were revised at our institution for aseptic osteolysis. Radiographs and a computer-assisted technique were used to quantify osteolysis. Implant stability was confirmed intraoperatively. Of 26 stable and 20 loose shells, the average area of osteolysis on anteroposterior radiographs showed no significant difference, whereas lateral radiographs showed a difference. The percentage of shell circumference with associated osteolysis seen on anteroposterior and lateral radiographs showed a significant difference. Diagnostic criterion of 50% shell circumference associated with osteolysis on lateral films has a sensitivity of 0.84 and a specificity of 0.54, and on anteroposterior views, a sensitivity of 1.0 and a specificity 0.27 for predicting shell loosening. Percent of shell circumference with surrounding osteolysis seems to be more predictive of loosening than the area of osteolysis. When 50% of the shell circumference has osteolysis evident on anteroposterior or lateral radiographs, but preferably anteroposterior radiographs, liner exchange should be considered so that the exchange procedure is still possible, rather than allowing the osteolysis to increase and compromise shell fixation.