Approach to Detection in Laser-Induced Breakdown Spectroscopy

Laser-induced emission spectra of stainless steels and aluminum irradiated with nanopulse lasers without setting delay: potential applications to remote sensing and laser micromachining

Spectral lines from the impurities held in stainless steel and in aluminum can be clearly identified in the UV and the visible spectra when emission is laser induced. These spectroscopic lines can be initiated in metal irradiated at moderate laser optical densities of about 2.5×10⁸W/cm². In addition to the lines arising from impurities found in some metals, it was found that some spectroscopic lines from iron oxide formed during irradiation were also detected at the above-mentioned power density. It was found that lines observed from iron oxide are consistent with what is reported in the literature. The investigations reported were produced on samples at optical densities that are sufficient to create an electric field that is about 10 times the air electrical breakdown near the focal point. The results reported were obtained without setting any delay between the laser Q-switch and the data acquisition. The spectroscopic data are comparable to those shown in the literature by laser-induced breakdown spectroscopy in term of signal-to-noise ratio and are promising in detecting impurities such as heavy metals in remote sensing applications, where pulse delay is not always practical due to atmospheric conditions and power requirements. As a marking procedure is used during the investigations, the method demonstrates how spectroscopic monitoring in real time can be applied during a procedure in laser micromachining applications.

Novel Applications of Laser-Induced Breakdown Spectroscopy

The goal of this review article is to provide a description of recent and novel laser-induced breakdown spectroscopy (LIBS) applications and developments, especially those discussed during the NASLIBS Conference, held during SciX in Providence, RI, in September 2015. This topic was selected in view of the numerous recent overall review papers that have successfully given a broad view of the current understanding of laser-material interactions and plasma development and have also discussed the wide landscape of analytical applications of LIBS. This paper is divided into sections that focus on a few of the many applications under development in the LIBS community. We provide a summary of updates to calibration-free LIBS (CF-LIBS) and associated developments using plasma characteristics to improve quantification in LIBS output, both in a dedicated section and as applications are discussed. We have also described the most recent publications studying the sources, generation, and use of molecular features in LIBS, including those naturally present in the spectra of organic materials, and those induced with the addition of salts to enable the measurement of halogens, not typically present in LIBS signals. In terms of development of applications of LIBS, we focused on the use of LIBS for indirect measurements such as pH and degree of humification in soil and heating value in coal. We also reviewed the extant literature on LIBS analysis of agricultural materials, coal, minerals, and metals. Finally, we discuss the nascent developments of spatially heterodyne spectroscopy, a method that seeks to circumnavigate a serious drawback of most spectrometers - very small optical throughput - through the use of interferometers.

Melted Paraffin Wax as an Innovative Liquid and Solid Extractant for Elemental Analysis by Laser-Induced Breakdown Spectroscopy

This work proposes a new development in the use of melted paraffin wax as a new extractant in a procedure designed to aggregate the advantages of liquid phase extraction (extract homogeneity, fast, and efficient transfer, low cost and simplicity) to solid phase extraction. As proof of concept, copper(II) in aqueous samples was converted into a hydrophobic complex of copper(II) diethyldithiocarbamate and subsequently extracted into paraffin wax. Parameters which affect the complexation and extraction (pH, DDTC, and Triton X-100 concentration, vortex agitation time and complexation time) were optimized in a univariate way. The combination of the extraction proposed procedure with laser-induced breakdown spectroscopy allowed the precise copper determination (coefficient of variation = 3.1%, n = 10) and enhanced detectability because of the concentration factor of 18 times. A calibration curve was obtained with a linear range of 0.50-10.00 mg L^-1 (R² = 0.9990, n = 7), LOD = 0.12 mg L^-1, and LOQ = 0.38 mg L^-1 under optimized conditions. An extraction procedure efficiency of 94% was obtained. The accuracy of the method was confirmed through the analysis of a reference material of human blood serum, by the spike and recovery trials with seawater, tap water, mineral water, and alcoholic beverages and by comparing with those results obtained by graphite furnace atomic absorption spectrometry.

Time-resolved spectroscopy using a chopper wheel as a fast shutter

Widely available, small form-factor, fiber-coupled spectrometers typically have a minimum exposure time measured in milliseconds, and thus cannot be used directly for time-resolved measurements at the microsecond level. Spectroscopy at these faster time scales is typically done with an intensified charge coupled device (CCD) system where the image intensifier acts as a "fast" electronic shutter for the slower CCD array. In this paper, we describe simple modifications to a commercially available chopper wheel system to allow it to be used as a "fast" mechanical shutter for gating a fiber-coupled spectrometer to achieve microsecond-scale time-resolved optical measurements of a periodically pulsed light source. With the chopper wheel synchronized to the pulsing of the light source, the time resolution can be set to a small fraction of the pulse period by using a chopper wheel with narrow slots separated by wide spokes. Different methods of synchronizing the chopper wheel and pulsing of the light sources are explored. The capability of the chopper wheel system is illustrated with time-resolved measurements of pulsed plasmas.

Non-gated laser induced breakdown spectroscopy provides a powerful segmentation tool on concomitant treatment of characteristic and continuum emission

We demonstrate the application of non-gated laser induced breakdown spectroscopy (LIBS) for characterization and classification of organic materials with similar chemical composition. While use of such a system introduces substantive continuum background in the spectral dataset, we show that appropriate treatment of the continuum and characteristic emission results in accurate discrimination of pharmaceutical formulations of similar stoichiometry. Specifically, our results suggest that near-perfect classification can be obtained by employing suitable multivariate analysis on the acquired spectra, without prior removal of the continuum background. Indeed, we conjecture that pre-processing in the form of background removal may introduce spurious features in the signal. Our findings in this report significantly advance the prior results in time-integrated LIBS application and suggest the possibility of a portable, non-gated LIBS system as a process analytical tool, given its simple instrumentation needs, real-time capability and lack of sample preparation requirements.

High repetition rate laser-induced breakdown spectroscopy using acousto-optically gated detection

This contribution introduces a new type of setup for fast sample analysis using laser-induced breakdown spectroscopy (LIBS). The novel design combines a high repetition rate laser (up to 50 kHz) as excitation source and an acousto-optical modulator (AOM) as a fast switch for temporally gating the detection of the emitted light. The plasma radiation is led through the active medium of the AOM where it is diffracted on the transient ultrasonic Bragg grid. The diffracted radiation is detected by a compact Czerny-Turner spectrometer equipped with a CCD line detector. Utilizing the new combination of high repetition rate lasers and AOM gated detection, rapid measurements with total integration times of only 10 ms resulted in a limit of detection (LOD) of 0.13 wt.% for magnesium in aluminum alloys. This short integration time corresponds to 100 analyses/s. Temporal gating of LIP radiation results in improved LODs and consecutively higher sensitivity of the LIBS setup. Therefore, an AOM could be beneficially utilized to temporally detect plasmas induced by high repetition rate lasers. The AOM in combination with miniaturized Czerny-Turner spectrometers equipped with CCD line detectors and small footprint diode pumped solid state lasers results in temporally gateable compact LIBS setups.

Dependence of laser-induced breakdown spectroscopy results on pulse energies and timing parameters using soil simulants

The dependence of some LIBS detection capabilities on lower pulse energies (<100 mJ) and timing parameters were examined using synthetic silicate samples. These samples were used as simulants for soil and contained minor and trace elements commonly found in soil at a wide range of concentrations. For this study, over 100 calibration curves were prepared using different pulse energies and timing parameters; detection limits and sensitivities were determined from the calibration curves. Plasma temperatures were also measured using Boltzmann plots for the various energies and the timing parameters tested. The electron density of the plasma was calculated using the full-width half maximum (FWHM) of the hydrogen line at 656.5 nm over the energies tested. Overall, the results indicate that the use of lower pulse energies and non-gated detection do not seriously compromise the analytical results. These results are very relevant to the design of field- and person-portable LIBS instruments.

Laser-induced breakdown spectroscopy (LIBS), part II: review of instrumental and methodological approaches to material analysis and applications to different fields

The first part of this two-part review focused on the fundamental and diagnostics aspects of laser-induced plasmas, only touching briefly upon concepts such as sensitivity and detection limits and largely omitting any discussion of the vast panorama of the practical applications of the technique. Clearly a true LIBS community has emerged, which promises to quicken the pace of LIBS developments, applications, and implementations. With this second part, a more applied flavor is taken, and its intended goal is summarizing the current state-of-the-art of analytical LIBS, providing a contemporary snapshot of LIBS applications, and highlighting new directions in laser-induced breakdown spectroscopy, such as novel approaches, instrumental developments, and advanced use of chemometric tools. More specifically, we discuss instrumental and analytical approaches (e.g., double- and multi-pulse LIBS to improve the sensitivity), calibration-free approaches, hyphenated approaches in which techniques such as Raman and fluorescence are coupled with LIBS to increase sensitivity and information power, resonantly enhanced LIBS approaches, signal processing and optimization (e.g., signal-to-noise analysis), and finally applications. An attempt is made to provide an updated view of the role played by LIBS in the various fields, with emphasis on applications considered to be unique. We finally try to assess where LIBS is going as an analytical field, where in our opinion it should go, and what should still be done for consolidating the technique as a mature method of chemical analysis.

A study of ablation, spatial, and temporal characteristics of laser-induced plasmas generated by multiple collinear pulses

Multi-pulse laser-induced breakdown spectroscopy (LIBS) in the collinear pulse configuration with time-integrating detection was performed on metallic samples in ambient air in an effort to clarify the contributing processes responsible for the signal enhancement observed in comparison with single-pulse excitation. Complementary experiments were also carried out on another LIBS setup using detection by an imaging spectrograph with high time resolution. The effects of laser bursts consisting of up to seven ns-range pulses from Nd-doped solid-state lasers operating at their fundamental wavelength and separated by 8.5-50 micros time gaps was studied. The ablation and emission characteristics of the generated plasmas were investigated using light profilometry, microscopy, plasma imaging, emission distribution mapping, time-resolved line emission monitoring, and plasma temperature calculations. The experimental data suggest that the two contributing processes mainly responsible for the signal enhancement effect are the plume reheating caused by the sequential laser pulses and, more dominantly, the increased material ablation attributed to the lower breakdown threshold for the preheated (molten) sample surface and/or the reduced background gas pressure behind the shockwave of preceding pulses.

Atmospheric pressure free liquid infrared MALDI mass spectrometry: toward a combined ESI/ MALDI-liquid chromatography interface

A new atmospheric pressure (AP)-MALDI-type interface has been developed based on a free liquid (FL) microbeam/microdroplets and a mid-infrared optical parametric oscillator (mid-IR OPO). The device is integrated into a standard on-line nanoESI interface. The generation of molecular ions in the gas phase is believed to be the result of a fast (explosive) laser-induced evaporative dispersion(not desorption) of the microbeam into statistically charged nanodroplets. Only the lowest charge states appear insignificant abundance in this type of experiment. Mass spectra of some common peptides have been acquired in positive ion mode, and the limit-of-detection of this first prototype (liquid microbeam setup) was evaluated to be 17 fmol per second. To improve the duty cycle and to reduce the sample consumption, a droplet-on-demand system was implemented (generating 100 pL droplets).With this setup, about 20 attomole of bradykinin were sufficient to achieve a signal-to-noise ratio better than five.This setup can be operated at flow rates down to 100 nL/min and represents a liquid MALDI alternative to the nanoESI. Our particular interest was the application of the developed ion source for on-line coupling of liquid chromatography with mass spectrometry. The flow rates(>100 microL/min), required for stable operation of the ion source in continuous liquid microbeam mode, matches perfectly the flow rate range of micro HPLC. Therefore, online LC/MS experiments have been realized, employing a microbore C18 reversed-phase column to separate an artificial peptide mixture and tryptic peptides of bovine serum albumin (performing a peptide mass fingerprint). In the latter case, sequence coverage of more than 90%has been achieved.

Insights into linear and rank correlation for material identification in laser-induced breakdown spectroscopy and other spectral techniques

The purpose of this work was to critically assess the potential and limitations of linear and rank correlation methods, not only relevant to laser-induced breakdown spectroscopy (LIBS), but to other spectroscopic techniques as well. Through computer simulations, it was demonstrated that a linear correlation is a more suitable technique for material identification than a rank correlation due to its better stability toward noise and better ability to detect small systematic variations in line intensities. The effect of noise on the results of correlation analysis has been studied. It was found that random noise causes correlation coefficients to be distributed normally, whereas flicker noise (random fluctuations in line intensities) results in a gamma distribution of correlation coefficients. Hence, the distribution of correlation coefficients can be used for detection of the type of noise that dominates correlated spectra. A potential of linear correlation analysis for plasma diagnostics has been demonstrated. It is based on a strong dependence of the linear correlation coefficient upon the line shapes of correlated spectral lines and, consequently, upon plasma parameters (plasma temperature, number densities).