Bacteria and Virus Inactivation: Relative Efficacy and Mechanisms of Peroxyacids and Chlor(am)ine

Effectiveness of Chlorine Against Tulane Virus, A Human Norovirus Surrogate, and Escherichia coli in Preharvest Agricultural Water

The use of fecally polluted water increases the risk of crop contamination with human norovirus (HuNoV) and its transmission to humans, particularly through ready-to-eat foods such as fresh produce. Preventing such exposure at preharvest stages is critical to ensure food safety throughout the supply chain. Despite HuNoV being the leading cause of foodborne illnesses in the United States, effective mitigating strategies in preharvest agricultural water remain underdeveloped. This research evaluated the effectiveness of calcium hypochlorite, a commercially available sanitizer to inactivate the Tulane virus, a surrogate for HuNoV, and Escherichia coli TVS 353 in preharvest agricultural waters. Water samples from two Florida farms were collected and inoculated with each microbial type, then treated with different free chlorine dosages (2, 4, 10, 15, 20, 30, and 40 ppm) for 5 and 10 min. The treatments were conducted at 12 °C to reflect colder months in Florida, aligning with the temperature specification outlined in the EPA/FDA protocol. Microbial counts were performed using plaque assay for Tulane virus and plate counts for E. coli. Since increasing the contact time from 5 to 10 min did not significantly enhance microbial inactivation rates (p > 0.05), kinetic models were fit to inactivation data for the 5-min contact time. The log10-logistic model predicted that achieving the EPA/FDA 3-log10 microbial reduction criteria in the agricultural water samples required treatment with free chlorine ranging between 0.6 and 0.9 ppm for E. coli and 9.6-23 ppm for Tulane virus. Compared to E. coli, Tulane virus was more resistant to inactivation with higher variability in reduction rates between the two agricultural water samples (p < 0.001). The necessity for elevated doses needed to inactivate viruses demands additional investigation, emphasizing the importance of implementing risk-based, environmentally safe treatments for agricultural water.

Peroxide Disinfection of Vesicle-Cloaked Murine Norovirus Clusters: Vesicle Membranes Protect Viruses from Inactivation

Vesicle-cloaked virus clusters, also known as viral vesicles, exhibit higher infectivity than free viruses and demonstrate persistence in the environment as well as resilience against disinfection. These emerging pathogens represent significant, yet often underestimated, health risks. Our study investigated peroxide disinfection of murine norovirus vesicles, a surrogate for human norovirus vesicles, and elucidated disinfection mechanisms. Peracetic acid, a neutral peroxide, rapidly inactivated murine norovirus vesicles. In contrast, negatively charged peroxides, i.e., peracetate and peroxymonosulfate, exhibited restricted effectiveness in inactivating murine noroviruses within vesicles. The largely intact viruses cloaked within vesicles remained infectious and retained their ability to replicate upon vesicle lysis triggered by mechanical forces, enzymatic activity, or chemical reactions following disinfection. Peroxides primarily targeted vesicle/viral proteins, particularly amino acid residues such as cysteine and methionine, without affecting the viral ORF2 gene fragment or vesicle structures. Disruption of viral internalization, rather than binding, plays a key role in infectivity loss. This work highlights the protective role of vesicle membranes and emphasizes the need for innovative disinfection approaches to effectively target viruses cloaked within vesicles.

Oxygen vacancy-dependent synergistic disinfection of antibiotic-resistant bacteria by BiOBr nanoflower induced H2O2 activation

Antibiotic-resistant bacteria (ARB) and antibiotic-resistant genes (ARGs) pose a significant threat to both ecosystems and human health. Owing to the excellent catalytic activity, eco-safety, and convenience for defect engineering, BiOBr with oxygen vacancies (OVs) of different density thus were fabricated and employed to activate H2O2 for ARB disinfection/ARGs degradation in present study. We found that BiOBr with OVs of appropriate density induced via ethanol reduction (BOB-E) could effectively activate H2O2, achieving excellent ARB disinfection and ARGs degradation efficiency. Moreover, this disinfection system exhibited remarkable tolerance to complex water environments and actual water conditions. In-situ characterization and theoretical calculations revealed that OVs in BOB-E could effectively capture and activate aqueous H2O2 into HO· and O2·-. The generated reactive oxygen species combined with electron transfer could damage the cell membrane system and degrade genetic materials of ARB, leading to effective disinfection. The impressive reusability, high performance achieved in two immobilized reaction systems (packed column and baffled ditch reactor), excellent degradation of emerging organic pollutants supported the feasibility of BOB-E/H2O2 system towards practical water decontamination. Overall, this study not only provides insights into fabrication of bismuth-based catalysts for efficient ARB disinfection/ARGs degradation via OVs regulation, but also paves the way for their practical applications.

Rapid and Highly Selective Fe(IV) Generation by Fe(II)-Peroxyacid Advanced Oxidation Processes: Mechanistic Investigation via Kinetics and Density Functional Theory

High-valent iron (Fe(IV/V/VI)) has been widely applied in water decontamination. However, common Fe(II)-activating oxidants including hydrogen peroxide (H2O2) and persulfate react slowly with Fe(II) and exhibit low selectivity for Fe(IV) production due to the cogeneration of radicals. Herein, we report peroxyacids (POAs; R-C(O)OOH) that can react with Fe(II) more than 3 orders of magnitude faster than H2O2, with high selectivity for Fe(IV) generation. Rapid degradation of bisphenol A (BPA, an endocrine disruptor) was achieved by the combination of Fe(II) with performic acid (PFA), peracetic acid (PAA), or perpropionic acid (PPA) within one second. Experiments with phenyl methyl sulfoxide (PMSO) and tert-butyl alcohol (TBA) revealed Fe(IV) as the major reactive species in all three Fe(II)-POA systems, with a minor contribution of radicals (i.e., •OH and R-C(O)O•). To understand the exceptionally high reactivity of POAs, a detailed computational comparison among the Fenton-like reactions with step-by-step thermodynamic evaluation was conducted. The high reactivity is attributed to the lower energy barriers for O-O bond cleavage, which is determined as the rate-limiting step for the Fenton-like reactions, and the thermodynamically favorable bidentate binding pathway of POA with iron. Overall, this study advances knowledge on POAs as novel Fenton-like reagents and sheds light on computational chemistry for these systems.

The reactivity of organic radicals in the performic, peracetic, perpropionic acids-based advanced oxidation process: A case study of sulfamethoxazole

Advanced oxidation processes (AOPs) based on peracetic acid (PAA) displayed great potential in removing emerging contaminants by generating HO• and organic radicals. Performic and perpropionic acids (PFA and PPA) also act as disinfectants, but their application potential has not been investigated yet. Here, we investigated the degradation mechanism and kinetics of sulfamethoxazole (SMX) by HO•, RC(O)O• species (including HC(O)O•, CH3C(O)O• and CH3CH2C(O)O•) and RC(O)OO• species (including HC(O)OO•, CH3C(O)OO• and CH3CH2C(O)OO•). The results show that the calculated reaction rate constants of SMX follow the order of HC(O)O• > CH3C(O)O• > CH3CH2C(O)O• > HO• > HC(O)OO• > CH3C(O)OO• > CH3CH2C(O)OO•. The reactivity towards SMX is strongly correlated with the redox potentials of reactive radicals. Hence, the RCOO• species play dominant roles in the purification of SMX in PFA/PAA/PPA-based AOPs. The degradation of SMX mainly proceeds via addition at the benzene ring, the hydrogen abstraction from the -NH2 group as well as the single electron transfer reaction. This study highlights the fundamental aspects of PFA, PAA, and PPA in the purification of sulfamethoxazole and enhances the role of organic radicals in the AOPs based on organic peracetic acids.

Activation of peracetic acid by electrodes using biogenic electrons: A novel energy- and catalyst-free process to eliminate pharmaceuticals

Peracetic acid (PAA) has received increasing attention as an alternative oxidant for wastewater treatment. However, existing processes for PAA activation to generate reactive species typically require external energy input (e.g., electrically and UV-mediated activation) or catalysts (e.g., Co2+), inevitably increasing treatment costs or introducing potential new contaminants that necessitate additional removal. In this work, we developed a catalyst-free, self-sustaining bioelectrochemical approach within a two-chamber bioelectrochemical system (BES), where a cathode electrode in-situ activates PAA using renewable biogenic electrons generated by anodic exoelectrogens (e.g., Geobacter) degrading biodegradable organic matter (e.g., acetic acid) in wastewater at the anode. This innovative BES-PAA technique achieved 98 % and 81 % removal of 2 µM sulfamethoxazole (SMX) in two hours at pH 2 (cation exchange membrane) and pH 6 (bipolar membrane) using 100 μM PAA without external voltage. Mechanistic studies, including radical quenching, molecular probe validation, electron spin resonance (ESR) experiments, and density functional theory (DFT) calculations, revealed that SMX degradation was driven by reactive species generated via biogenic electron-mediated OO cleavage of PAA, with CH3C(O)OO• contributing 68.1 %, •OH of 18.4 %, and CH3C(O)O• of 9.4 %, where initial formation of •OH and CH3C(O)O• rapidly reacts with PAA to produce CH3C(O)OO•. The presence of common water constituents such as anions (e.g., Cl-, NO3-, and H2PO4-) and humic acid (HA) significantly hinders SMX removal via the BES-PAA technique, whereas CO32- and HCO3- ions have a comparatively minor impact. Additionally, the study investigated the removal of various pharmaceuticals present in secondary treated municipal wastewater, attributing differences in removal efficiency to the selective action of CH3C(O)OO•. This research demonstrates a novel PAA activation method that is ecologically benign, inexpensive, and capable of overcoming catalyst deactivation and secondary pollution issues.

Far-UVC 222 nm Treatment: Effects of Nitrate/Nitrite on Disinfection Byproduct Formation Potential

Irradiation at far ultraviolet C (far-UVC) 222 nm by krypton chloride (KrCl*) excilamps can enhance microbial disinfection and micropollutant photolysis/oxidation. However, nitrate/nitrite, which absorbs strongly at 222 nm, may affect the formation of disinfection byproducts (DBPs). Herein, we evaluated model organic matter and real water samples and observed a substantial increase in the formation potential for trichloronitromethane (chloropicrin) (TCNM-FP), a nitrogenous DBP, by nitrate or nitrite after irradiation at 222 nm. At a disinfection dose of 100 mJ·cm-2, TCNM-FP of humic acids and fulvic acids increased from ∼0.4 to 25 and 43 μg·L-1, respectively, by the presence of 10 mg-N·L-1 nitrate. For the effect of nitrate concentration, the TCNM-FP peak was observed at 5-10 mg-N·L-1. Stronger fluence caused a greater increase of TCNM-FP. Similarly, the increase of TCNM-FP was also observed for wastewater and drinking water samples containing nitrate. Pretreatment using ozonation and coagulation, flocculation, and filtration or the addition of H2O2 can effectively control TCNM-FP. The formation potential of other DBPs was minorly affected by irradiation at 222 nm regardless of whether nitrate/nitrite was present. Overall, far-UVC 222 nm treatment poses the risk of increasing TCNM-FP of waters containing nitrate or nitrite at environmentally relevant concentrations and the mitigation strategies merit further research.

Assessment of chlorine and hydrogen peroxide on airborne bacteria: Disinfection efficiency and induction of antibiotic resistance

Airborne pathogens severely threaten public health worldwide. Air disinfection is essential to ensure public health. However, excessive use of disinfectants may endanger environmental and ecological security due to the residual disinfectants and their by-products. This study systematically evaluated disinfection efficiency, induction of multidrug resistance, and the underlying mechanisms of disinfectants (NaClO and H2O2) on airborne bacteria. The results showed that airborne bacteria were effectively inactivated by atomized NaClO (>160 μg/L) and H2O2 (>320 μg/L) after 15 min. However, some bacteria still survived after disinfection by atomized NaClO (0-80 μg/L) and H2O2 (0-160 μg/L), and they exhibited significant increases in antibiotic resistance. The whole-genome sequencing of the resistant bacteria revealed distinct mutations that were responsible for both antibiotic resistance and virulence. This study also provided evidences and insights into possible mechanisms underlying the induction of antibiotic resistance by air disinfection, which involved intracellular reactive oxygen species formation, oxidative stress responses, alterations in bacterial membranes, activation of efflux pumps, and the thickening of biofilms. The present results also shed light on the role of air disinfection in inducing antibiotic resistance, which could be a crucial factor contributing to the global spread of antibiotic resistance through the air.

Unveiling the environmental significance of acetylperoxyl radical: Reactivity quantification and kinetic modeling

Acetylperoxyl radical (CH3C(O)OO•) is among highly reactive organic radicals which are known to play crucial roles in atmospheric chemistry, aqueous chemistry and, most recently, peracetic acid (PAA)-based advanced oxidation processes. However, fundamental knowledge for its reactivity is scarce and severely hampers the understanding of relevant environmental processes. Herein, three independent experimental approaches were exploited for revelation and quantification of the reaction rates of acetylperoxyl radical. First, we developed and verified laser flash photolysis of biacetyl, ultraviolet (UV) photolysis of biacetyl, and pulse radiolysis of acetaldehyde, each as a clean source of CH3C(O)OO•. Then, using competition kinetics and selection of suitable probe and competitor compounds, the rate constants between CH3C(O)OO• and compounds of diverse structures were determined. The three experimental approaches complemented in reaction time scale and ease of operation, and provided cross-validation of the rate constants. Moreover, the formation of CH3C(O)OO• was verified by spin-trapped electron paramagnetic resonance, and potential influence of other reactive species in the systems was assessed. Overall, CH3C(O)OO• displays distinctively high reactivity and selectivity, reacting especially favorably with naphthyl and diene compounds (k ∼ 107-108 M-1 s-1) but sluggishly with N- and S-containing groups. Significantly, we demonstrated that incorporating acetylperoxyl radical-oxidation reactions significantly improved the accuracy in modeling the degradation of environmental micropollutants by UV/PAA treatment. This study is among the most comprehensive investigation for peroxyl radical reactivity to date, and establishes a robust methodology for investigating organic radical chemistry. The determined rate constants strengthen kinetic databases and improve modeling accuracy for natural and engineered systems.

Revisiting the Electron Transfer Mechanisms in Ru(III)-Mediated Advanced Oxidation Processes with Peroxyacids and Ferrate(VI)

The potential of Ru(III)-mediated advanced oxidation processes has attracted attention due to the recyclable catalysis, high efficiency at circumneutral pHs, and robust resistance against background anions (e.g., phosphate). However, the reactive species in Ru(III)-peracetic acid (PAA) and Ru(III)-ferrate(VI) (FeO42-) systems have not been rigorously examined and were tentatively attributed to organic radicals (CH3C(O)O•/CH3C(O)OO•) and Fe(IV)/Ru(V), representing single electron transfer (SET) and double electron transfer (DET) mechanisms, respectively. Herein, the reaction mechanisms of both systems were investigated by chemical probes, stoichiometry, and electrochemical analysis, revealing different reaction pathways. The negligible contribution of hydroxyl (HO•) and organic (CH3C(O)O•/CH3C(O)OO•) radicals in the Ru(III)-PAA system clearly indicated a DET reaction via oxygen atom transfer (OAT) that produces Ru(V) as the only reactive species. Further, the Ru(III)-performic acid (PFA) system exhibited a similar OAT oxidation mechanism and efficiency. In contrast, the 1:2 stoichiometry and negligible Fe(IV) formation suggested the SET reaction between Ru(III) and ferrate(VI), generating Ru(IV), Ru(V), and Fe(V) as reactive species for micropollutant abatement. Despite the slower oxidation rate constant (kinetically modeled), Ru(V) could contribute comparably as Fe(V) to oxidation due to its higher steady-state concentration. These reaction mechanisms are distinctly different from the previous studies and provide new mechanistic insights into Ru chemistry and Ru(III)-based AOPs.

Efficacy and Mechanism of Antibiotic Resistance Gene Degradation and Cell Membrane Damage during Ultraviolet Advanced Oxidation Processes

Combinations of UV with oxidants can initiate advanced oxidation processes (AOPs) and enhance bacterial inactivation. However, the effectiveness and mechanisms of UV-AOPs in damaging nucleic acids (e.g., antibiotic resistance genes (ARGs)) and cell integrity represent a knowledge gap. This study comprehensively compared ARG degradation and cell membrane damage under three different UV-AOPs. The extracellular ARG (eARG) removal efficiency followed the order of UV/chlorine > UV/H2O2 > UV/peracetic acid (PAA). Hydroxyl radical (•OH) and reactive chlorine species (RCS) largely contributed to eARG removal, while organic radicals made a minor contribution. For intracellular ARGs (iARGs), UV/H2O2 did not remove better than UV alone due to the scavenging of •OH by cell components, whereas UV/PAA provided a modest synergism, likely due to diffusion of PAA into cells and intracellular •OH generation. Comparatively, UV/chlorine achieved significant synergistic iARG removal, suggesting the critical role of the RCS in resisting cellular scavenging and inactivating ARGs. Additionally, flow cytometry analysis demonstrated that membrane damage was mainly attributed to chlorine oxidation, while the impacts of radicals, H2O2, and PAA were negligible. These results provide mechanistic insights into bacterial inactivation and fate of ARGs during UV-AOPs, and shed light on the suitability of quantitative polymerase chain reaction (qPCR) and flow cytometry in assessing disinfection performance.

Influence of Amino Acid Substitutions in Capsid Proteins of Coxsackievirus B5 on Free Chlorine and Thermal Inactivation

The sensitivity of enteroviruses to disinfectants varies among genetically similar variants and coincides with amino acid changes in capsid proteins, although the effect of individual substitutions remains unknown. Here, we employed reverse genetics to investigate how amino acid substitutions in coxsackievirus B5 (CVB5) capsid proteins affect the virus' sensitivity to free chlorine and heat treatment. Of ten amino acid changes observed in CVB5 variants with free chlorine resistance, none significantly reduced the chlorine sensitivity, indicating a minor role of the capsid composition in chlorine sensitivity of CVB5. Conversely, a subset of these amino acid changes located at the C-terminal region of viral protein 1 led to reduced heat sensitivity. Cryo-electron microscopy revealed that these changes affect the assembly of intermediate viral states (altered and empty particles), suggesting that the mechanism for reduced heat sensitivity could be related to improved molecular packing of CVB5, resulting in greater stability or altered dynamics of virus uncoating during infection.

Mechanistic Insight for Disinfection Byproduct Formation Potential of Peracetic Acid and Performic Acid in Halide-Containing Water

Peracetic acid (PAA) and performic acid (PFA) are two major peroxyacid (POA) oxidants of growing usage. This study reports the first systematic evaluation of PAA, PFA, and chlorine for their disinfection byproduct (DBP) formation potential in wastewater with or without high halide (i.e., bromide or iodide) concentrations. Compared with chlorine, DBP formation by PAA and PFA was minimal in regular wastewater. However, during 24 h disinfection of saline wastewater, PAA surprisingly produced more brominated and iodinated DBPs than chlorine, while PFA effectively kept all tested DBPs at bay. To understand these phenomena, a kinetic model was developed based on the literature and an additional kinetic investigation of POA decay and DBP (e.g., bromate, iodate, and iodophenol) generation in the POA/halide systems. The results show that PFA not only oxidizes halides 4-5 times faster than PAA to the corresponding HOBr or HOI but also efficiently oxidizes HOI/IO- to IO3-, thereby mitigating iodinated DBP formation. Additionally, PFA's rapid self-decay and slow release of H2O2 limit the HOBr level over the long-term oxidation in bromide-containing water. For saline water, this paper reveals the DBP formation potential of PAA and identifies PFA as an alternative to minimize DBPs. The new kinetic model is useful to optimize oxidant selection and elucidate involved DBP chemistry.