Modified Poly(acrylic acid)-Based Hydrogels for Enhanced Mainstream Removal of Ammonium from Domestic Wastewater

Radiation cross-linked ultra-absorbent hydrogel to rationalize irrigation water and fertilizer for maize planting in drought conditions

The study addresses the potential negative impacts of climate change on water resources, specifically irrigation water for crops. The radiation technique produces the biomaterial hydrogel as a soil conditioner by polymerizing hydroxy ethyl cellulose/acrylamide (HEC/AAm) at various irradiation doses and copolymer concentrations. A maximum swelling of 23.4 g/g is attained by (HEC/PAAm) hydrogel at 1/7.5 ratio, prepared by 10 kGy gamma irradiation. The study introduces a new class of ultra-absorbent hydrogel (UAH) to address the low swelling limitation for soil conditioner applications. The alkaline hydrolysis treatments with NaOH, LiOH, and KOH enhance the water absorbency of (HEC/PAAm) hydrogel, with the highest capacity of 1220 g/g achieved by the KOH treatment, surpassing NaOH (622 g/g) and LiOH (540 g/g). The cumulative release of fertilizers from the UAH sample shows a slow and controlled release behavior. Urea takes 22 days to reach 100 % release. The UAH demonstrates water retention for 28 days, improving the growth of Zea mays L. at drought stress levels of 0 %, 25 %, 50 %, and 100 %, revealing an increase in shoot length by 16 %, 19 %, 24 %, and 20 %, respectively. Also, UAH increased the contents of chlorophyll a, b, a + b, and carotenoid on maize plant leaves compared to the control sample.

Nitrogen removal from wastewater by an immobilized consortium of microalgae-bacteria in hybrid hydrogels

The high content of nitrogen in wastewater brings some operational, technical, and economical issues in conventional technologies. The aim of this study was to evaluate the nitrogen removal by hybrid hydrogels containing consortium microalgae-nitrifying bacteria in the presence of activated carbon (AC) used as an adsorbent of inhibitory substances. Hybrid hydrogels were synthesized from polyvinyl alcohol (PVA), sodium alginate (SA), biomass (microalgae-nitrifying bacteria), and AC. The hybrid hydrogels were evaluated based on the change in ammonium (NH₄), nitrate (NO₃), and chemical demand of oxygen (COD) concentrations, nitrification rate, and other parameters during 72 h. Results indicated that NH₄ removal was more effective for hydrogels without AC than with AC, without significant differences regarding consortium biomass concentration (5 or 16%), presenting final concentrations of 3.13 and 3.75 mg NH₄/L for hydrogels with 5 and 16% of the biomass, respectively. Regarding NO₃ production, hydrogels without AC reached concentrations of 25.9 and 39.77 mg NO₃/L for 5 and 16% of the biomass, respectively, while treatments with AC ended with 2.17 and 1.37 mg NO₃/L. This confirms that hydrogels can carry out the nitrification process and do not need AC to remove potential inhibitors. The best performance was observed for the hydrogel with 5% of biomass without AC with a nitrification rate of 0.43 mg N/g TSS·h.

Removal of Ammonium Ions from Aqueous Solutions Using Alkali-Activated Analcime as Sorbent

Five alkali-activated analcime (ANA) sorbents (ANA-MK 1, ANA 2, ANA 3, ANA-MK 4, and ANA-MK 5) were developed for ammonium (NH4+) ion removal. Acid treatment and calcination were used as pre-treatments for analcime, and metakaolin (MK) was used as a blending agent in three sorbents. Sorption experiments were performed to evaluate the effects of sorbent dosage (1–20 g L−1), initial NH4+ ion concentration (5–1000 g L−1), and contact time (1 min–24 h). ANA-MK 1, ANA 2, and ANA-MK 4 were the most efficient sorbents for NH4+ ion removal, with a maximum experimental sorption uptake of 29.79, 26.00, and 22.24 mg g−1, respectively. ANA 3 and ANA-MK 5 demonstrated lower sorption capacities at 7.18 and 12.65 mg g−1, respectively. The results for the sorption of NH4+ ions onto the alkali-activated analcime surfaces were modeled using several isotherms. The Langmuir, Freundlich, Sips, and Bi-Langmuir isotherms were the best isotherm models to represent the studied systems. The results of the kinetic studies showed the maximum NH4+ ion removal percentage of the sorbents was ~80%, except for ANA-MK 5, which had a ~70% removal. Moreover, the pseudo-first-order, pseudo-second-order, and Elovich models were applied to the experimental data. The results showed that the sorption process for ANA-MK 1, ANA 2, ANA 3, and ANA-MK 4 followed the Elovich model, whereas the pseudo-second-order model provided the best correlation for ANA-MK 5.

Efficient direct membrane filtration (DMF) of municipal wastewater for carbon recovery: Application of a simple pretreatment and selection of an appropriate membrane pore size

Considerable attention has been paid in recent years to the recovery and effective utilization of organic matter in municipal wastewater for the establishment of a circular economy. Direct membrane filtration (DMF) of municipal wastewater using microfiltration (MF) or ultrafiltration (UF) membranes to retain and concentrate the organic matter in municipal wastewater could be a practical option for this purpose. However, severe membrane fouling and high concentrations of organic matter remaining in the DMF permeate are concerns to be addressed. Application of a simple pretreatment using fixed biofilms was investigated to address these issues. In this study, experiments were carried out at an existing municipal wastewater treatment plant. A moving bed biofilm reactor (MBBR) process operated under a very short HRT of 1 h and DO concentration of 0.5 mg/L selectively degraded low-molecular-weight dissolved organic matter in municipal wastewater without degradation of membrane-recoverable suspended and colloidal organic matter. Application of the pretreatment did not reduce the amount of organic carbon recovered by DMF using an MF membrane (approximately 70% of the influent COD being recovered), while it dramatically mitigated the membrane fouling probably due to the alteration of characteristics of dissolved organic matter in wastewater. The pretreatment also reduced the concentration of organic matter in the DMF permeate by 41%: COD concentration in the DMF permeate was as low as 40 mg/L. With the established MBBR pretreatment, performances of MF (0.1 µm) and UF (molecular weight cut-off: 150,000) membranes for DMF were compared in parallel. It was found that the increase of the recoverable amount of organic matter by using UF was marginal (about 5%), whereas fouling in UF was much more severe than that in MF. The severe fouling in UF was caused by inorganic colloids such as FeS that could pass through MF membranes but be retained by UF membranes. Based on the results obtained in this study, it is concluded that MF is more suitable than UF for efficient DMF.

Nanocellulose fine-tuned poly(acrylic acid) hydrogel for enhanced diclofenac removal

Hydrogel was recognized as one of the most promising materials for adsorption of pharmaceuticals and personal care products (PPCPs). The highly efficient bio-based nanocelluloses fine-tuned poly(acrylic acid) hydrogel (PAA/NC) adsorbent was constructed by adjusting aspect ratio, surface charge and crystallinity of NC. The cross-linked networks were fabricated through a single-step free-radical polymerization via steric effect and hydrogen bonds. The uniform three-dimensional structures with abundant macropores and mesopores were in-situ visualized by the cryogenic-scanning electron microscopy (Cryo-SEM). The diclofenac adsorption capacity of TEMPO oxidized cellulose nanofibers (TCNF) incorporated PAA hydrogel (PAA/TCNF, 559.8 mg·g^-1) was circa 2.1 times higher than pristine PAA (293.5 mg·g^-1) due to the elevated specific surface area, favorable spatial structure with unimpeded channels and abundant surface-charged carboxylic groups. Moreover, PAA/NC hydrogel exhibited a wide-pH applicability and high salinity tolerance. The adsorption was predominantly determined by hydrogen bonds, validated by XPS and FT-IR analysis. It was demonstrated developed PAA/NC hydrogel with unique porous structure significantly enhanced adsorption capacity for potential application in the purification of refractory organic pollutants-containing wastewater.

Controlled-release urea combined with fulvic acid enhanced carbon/nitrogen metabolic processes and maize growth

BACKGROUND

Controlled-release urea (CRU) or fulvic acid (FA), when applied, have been shown to increase nitrogen (N) use efficiency (NUE) or to stimulate plant growth, yet their interactive effects are not well explored. The objective of this study was to investigate the synergistic mechanisms of CRU combined with FA (CRU + FA) on maize (Zea mays L.) growth. Through the experimental design with five treatments, the N metabolism through the transcriptomic analysis of maize leaf, endogenous hormones, photosynthesis enzymes in maize leaf and root, and maize yield and NUE were evaluated.

RESULTS

Compared with CRU treatment, CRU + FA treatment significantly increased auxin, nitrate reductase, and glutamate dehydrogenase in leaf by 35.4%, 43.9%, 40.8% and 19.5%, respectively, as well as, the relative content of the leaf chlorophyll and photosynthetic rate by 14.8% and 45.6%, respectively, at 12-leaf collar stage; the carbon/nitrogen (C/N) metabolic process was significantly enriched in CRU + FA treatment by 312 and 418 genes, according to transcriptome profiles of C/N metabolic in leaves from various fertilizer treated maize; maize yield and NUE of CRU + FA treatment were increased by 6.3% and 38.4%, respectively.

CONCLUSIONS

These results demonstrated that CRU + FA is a viable fertilization scheme that can enhance maize growth, yield and NUE through their synergies in improving N uptake, promoting photosynthesis, increasing C/N metabolic processes, and enhancing enzyme activities. © 2021 Society of Chemical Industry.

Facile Photolithographic Fabrication of Zwitterionic Polymer Microneedles with Protein Aggregation Inhibition for Transdermal Drug Delivery

Microneedle technology has received considerable attention in transdermal drug delivery system research owing to its minimally invasive and convenient self-administration with enhanced transdermal transport. The pre-drug loading microneedle method has been developed for several protein and chemical medicines. However, the protein activity and efficacy are severely affected owing to protein aggregation. Herein, we aim to develop non-degradable hydrogel photocross-linkable microneedles for suppressing protein aggregation. Four-point star-shaped microneedles are fabricated via a photolithography process, and sulfobetaine (SPB) monomer is combined with dextran-glycidyl methacrylate/acrylic acid to form the hydrogel network. Incorporating zwitterionic poly-sulfobetaine (poly-SPB) in the microneedles enables the protection of proteins from denaturation even under external stress, releases the proteins in their native state (without activity loss), and exhibits sufficient mechanical strength to penetrate porcine skin. The microneedles exhibit a high drug loading capacity along with an efficient drug release rate. The rhodamine B drug loading and release model shows that the microneedles can load 8 μg of drugs on one microneedle patch of 41 needles and release nearly 80% of its load within 1 h. We anticipate that this pre-drug loading platform and the advanced features of the microneedles can provide an effective option for administering therapeutic drugs.

Circular economy-driven ammonium recovery from municipal wastewater: State of the art, challenges and solutions forward

In current biological nitrogen removal (BNR) processes, most of ammonium in municipal wastewater is biologically transformed to nitrogen gas, making ammonium recovery impossible. Thus, this article aims to provide a holistic review with in-depth discussions on (i) current BNR processes for municipal wastewater treatment, (ii) environmental and economic costs behind ammonium in municipal wastewater, (iii) state of the art of ammonium recovery from municipal wastewater including anaerobic membrane bioreactor turning municipal wastewater to a liquid fertilizer, capturing ammonium in phototrophic biomass, waste activated sludge for land application, bioelectrochemical systems, biological conversion of ammonium to nitrous oxide as a fuel oxidizer, and adsorption, (iv) feasibility and challenge of adsorption for ammonium recovery from municipal wastewater and (v) innovative municipal wastewater reclamation processes coupled with ammonium recovery. Moving forward, municipal wastewater reclamation and resource recovery should be addressed under the framework of circular economy.

Compact wastewater treatment process based on abiotic nitrogen management achieved high-rate and facile pollutants removal

Chemically enhanced primary treatment (CEPT), ammonium ion exchange and regeneration (AIR) and membrane bioreactor (MBR) were coupled as CAIRM to treat domestic wastewater compactly and efficiently. CAIRM achieved efficient removal of chemical oxygen demand, ammonia nitrogen, total nitrogen (TN) and total phosphorus with total hydraulic retention time of 4.6 h, and obtained 2.3 ± 0.9 mg/L TN in the effluent. CEPT removed phosphate and impurities and prevented AIR from pollution. AIR maintained excellent nitrogen removal with a slight decrease in the exchange capacity of ion exchangers. MBR polished the effluent from AIR, and the larger particle size and better dewaterability of sludge mitigated the membrane fouling. Many heterotrophic genera, such as Rhodobacter and Defluviimonas, were enriched in the oligotrophic MBR. This study demonstrates the viability and stability of CAIRM in efficient wastewater treatment, which will address critical challenges in insufficient nitrogen removal and high land occupancy of current processes.

Magnetic poly(acrylic acid)-based hydrogels for rapid ammonium sorption and efficient sorbent separation from sewage

Ammonium sorption and recovery processes typically take place in conventional packed columns, with a configuration that enables maximum sorption by the sorbents. However, batch or semi-continuous operations in packed columns have associated issues such as scaling and frequent backwashing requirements, which are economically prohibitive. As an alternative, ammonium sorption could occur in well-mixed continuously stirred tanks, which would allow for the ammonium sorption process to be retrofitted in existing wastewater treatment plants, provided that efficient sorbent separation can be achieved. This study demonstrates, for the first time, the preparation of magnetic poly(acrylic acid)-based (PAA) ammonium sorbents through the incorporation of magnetic (Fe₃O₄) nanoparticles (MNP) produced via scalable and cost-effective electrochemical synthesis. The MNP and PAA hydrogels were synthesized independently and the MNPs subsequently integrated into the PAA hydrogel network by particle diffusion and physical entrapment. No adverse effects on swelling and ammonium sorption following immersion in either synthetic or real sewage were observed after MNPs were incorporated into the hydrogels. Importantly, PAA-MNP hydrogels demonstrated high ammonium sorption efficiencies (80-93%) in real sewage and achieved rapid ammonium recovery of 73 ± 1.1% within 15 min of mild acid washing (pH 4) 15 min at a maximum recovery.

Revealing Interplay of Defects in SnO2 Quantum Dots for Blue Luminescence and Selective Trace Ammonia Detection at Room Temperature

Defect chemistry in SnO₂ is well established for resistive sensors but remains to be elusive for photoluminescence (PL) sensors. It demands a comprehensive understanding of the role of cationic and oxygen defects as well as the creation of abundant such defects to provide a selective PL signal. To accomplish it, SnO₂ quantum dots (QDs ∼ 2.4 nm) are prepared without a capping agent along with other dimensions. Then, the relationship of defects with the blue-emission PL is unfolded by electron energy loss spectroscopy, lifetime measurements, X-ray absorption, and Raman spectroscopic measurements. The defects acting as Lewis acid sites are utilized for selective ammonia detection. Huge enhancements of the obscured blue luminescence at 2.77 and 2.96 eV from the SnO₂ QDs are observed because of interaction with ammonia. The linear variation of PL intensities with analyte concentrations and the recovery of the sensor are elaborated with detection up to 5 ppm. The interplay of defects in SnO₂ is further established theoretically for site-specific interactions with ammonia by density functional theory (DFT) calculations. Thus, the unique mechanism revealed for the superlative performance of the PL sensor with uncapped SnO₂ QDs provides a novel platform for defect-engineering-based optoelectronic applications.