Biotransformation of AFFF Component 6:2 Fluorotelomer Thioether Amido Sulfonate Generates 6:2 Fluorotelomer Thioether Carboxylate under Sulfate-Reducing Conditions

A review of the occurrence and microbial transformation of per- and polyfluoroalkyl substances (PFAS) in aqueous film-forming foam (AFFF)-impacted environments

Aqueous film-forming foams (AFFFs) have been extensively used for extinguishing hydrocarbon-fuel fires at military sites, airports, and fire-training areas. Despite being a significant source of per- and polyfluoroalkyl substances (PFAS), our understanding of PFAS occurrence in AFFF formulations and AFFF-impacted environments is limited, as is the impact of microbial transformation on the environment fate of AFFF-derived PFAS. This literature review compiles PFAS concentrations in electrochemical fluorination (ECF)- and fluorotelomer (FT)-based AFFFs and provides an overview of PFAS occurrence in AFFF-impacted environments. Our analysis reveals that AFFF use is a predominant point source of PFAS contamination, including primary precursors (polyfluoroalkyl substances as AFFF components), secondary precursors (polyfluoroalkyl transformation products of primary precursors), and perfluoroalkyl acids (PFAAs). Moreover, there are discrepancies between PFAS concentration profiles in AFFFs and those measured in AFFF-impacted media. For example, primary precursors constitute 52.6 % and 99.5 % of PFAS mass in ECF- and FT-based AFFFs, respectively, whereas they represent only 0.7 % total mass in AFFF-impacted groundwater. Conversely, secondary precursors, which constitute <1 % of PFAS in AFFFs, represent 4.0-27.8 % of PFAS in AFFF-impacted environments. The observed differences in PFAS levels between AFFFs and environmental samples are likely due to in-situ biotransformation processes. Biotransformation rates and pathways reported for AFFF-derived primary and secondary precursors varied among different classes of precursors, consistent with the PFAS occurrence in AFFF-impacted environments. For example, readily biodegradable primary precursors, N-dimethyl ammonio propyl perfluoroalkane sulfonamide (AmPr-FASA) and n:2 fluorotelomer thioether amido sulfonate (n:2 FtTAoS), were rarely detected in AFFF-impacted environments. In contrast, key secondary precursors, perfluoroalkane sulfonamides (FASAs) and n:2 fluorotelomer sulfonate (n:2 FTS), were widely detected, which was attributed to their resistance to biotransformation. Key knowledge gaps and future research priorities are presented to better understand the occurrence, fate, and transport of AFFF-derived PFAS in the environment and to design more effective remediation strategies.

Nationwide occurrence and discharge mass load of per- and polyfluoroalkyl substances in effluent and biosolids: A snapshot from 75 wastewater treatment plants across Australia

Wastewater treatment plants (WWTPs) have been recognized as secondary sources of per- and polyfluoroalkyl substances (PFAS) released into the environment. In this study, PFAS concentrations were measured in effluent and biosolids samples collected from 75 WWTPs across Australia during the 2016 Census period, which covers more than half of the Australian population. Twelve PFAS compounds, including six C5-C10 perfluoroalkyl carboxylic acids (PFCAs), four perfluoro sulfonic acids (PFSAs) such as perfluorobutane sulfonate (PFBS), perfuorohexane sulfonic (PFHxS), perfluorooctane sulfonic acid (PFOS), and perfluorodecane sulfonic acid (PFDS), and one fluorotelomer sulfonic acid (6:2 FTS), were detected in the effluent, with concentrations up to 504 ng/L (PFHxS). Among these, perfluorooctanoic acid (PFOA), perfluorohexanoic acid (PFHxA), and perfluoropentanic acid (PFPeA) exhibited the highest median concentrations. In the biosolids, a total of 21 PFAS compounds were detected, encompassing ten C4-C14 PFCAs, four PFSAs, two FTS (6:2 and 8:2 FTS), perfluorooctane sulfonamide (PFOSA), two perfluorooctane sulfonamido acetic acid (NMethyl FOSAA and NEthyl FOSAA), and two perfluorooctane sulfonamido ethanol (FOSE), with dry weight (dw) concentrations approaching 235 ng/g (PFOS). The highest median and mean concentrations were observed for perfluorodecanoic acid (PFDA) and PFOS. An annual discharge of approximately 250 kg of the total 21 PFAS compounds was estimated through the effluent and biosolids of the participating WWTPs. Notably, PFOS and 6:2 FTS constituted the largest proportion of total PFAS in the WWTPs' output. While PFCAs were higher in effluent concentrations compared to influent levels across most WWTPs (92% of WWTPs for ∑8PFCAs), the concentrations of PFSAs either decreased or remained relatively stable (in 80% of WWTPs for ∑4PFSAs) throughout the wastewater treatment process.

Stability and Biotransformation of 6:2 Fluorotelomer Sulfonic Acid, Sulfonamide Amine Oxide, and Sulfonamide Alkylbetaine in Aerobic Sludge

The 6:2 fluorotelomer sulfonamide (6:2 FTSAm)-based compounds signify a prominent group of per- and polyfluoroalkyl substances (PFAS) widely used in contemporary aqueous film-forming foam (AFFF) formulations. Despite their widespread presence, the biotransformation behavior of these compounds in wastewater treatment plants remains uncertain. This study investigated the biotransformation of 6:2 FTSAm-based amine oxide (6:2 FTNO), alkylbetaine (6:2 FTAB), and 6:2 fluorotelomer sulfonic acid (6:2 FTSA) in aerobic sludge over a 100-day incubation period. The biotransformation of 6:2 fluorotelomer sulfonamide alkylamine (6:2 FTAA), a primary intermediate product of 6:2 FTNO, was indirectly assessed. Their stability was ranked based on the estimated half-lives (t1/2): 6:2 FTAB (no obvious products were detected) ≫ 6:2 FTSA (t1/2 ≈28.8 days) > 6:2 FTAA (t1/2 ≈11.5 days) > 6:2 FTNO (t1/2 ≈1.2 days). Seven transformation products of 6:2 FTSA and 15 products of 6:2 FTNO were identified through nontarget and suspect screening using high-resolution mass spectrometry. The transformation pathways of 6:2 FTNO and 6:2 FTSA in aerobic sludge were proposed. Interestingly, 6:2 FTSAm was hardly hydrolyzed to 6:2 FTSA and further biotransformed to perfluoroalkyl carboxylic acids (PFCAs). Furthermore, the novel pathways for the generation of perfluoroheptanoic acid (PFHpA) from 6:2 FTSA were revealed.

Efficient and fast remediation of soil contaminated by per- and polyfluoroalkyl substances (PFAS) by high-frequency heating

This study presents a novel thermal technology (high-frequency heating, HFH) for the decontamination of soil containing per- and polyfluoroalkyl substances (PFAS) and aqueous film-forming foams (AFFFs). Ultra-fast degradation of short-chain PFAS, long-chain homologs, precursors, legacy PFAS, emerging PFAS was achieved in a matter of minutes. The concentrations of PFAS and the soil type had a negligible impact on degradation efficiency, possibly due to the ultra-fast degradation rate overwhelming potential differences. Under the current HFH experiment setup, we achieved near-complete degradation (e.g., >99.9%) after 1 min for perfluoroalkyl carboxylic acids and perfluoroalkyl ether carboxylic acids and 2 min for perfluoroalkanesulfonic acids. Polyfluoroalkyl precursors in AFFFs were found to degrade completely within 1 min of HFH; no residual cationic, zwitterionic, anionic, or non-ionic intermediate products were detected following the treatment. The gaseous byproducts were considered. Most of gaseous organofluorine products of PFAS at low-and-moderate temperatures disappeared when temperatures reached 890 °C, which is in the temperature zone of HFH. For the first time, we demonstrated minimal loss of PFAS in water during the boiling process, indicating a low risk of PFAS entering the atmosphere with the water vapor. The findings highlight HFH its potential as a promising remediation tool for PFAS-contaminated soils.

Investigating rate-limited sorption, sorption to air-water interfaces, and colloid-facilitated transport during PFAS leaching

Various sorption processes affect leaching of per- and polyfluoroalkyl substances (PFAS) such as PFOA and PFOS. The objectives of this study are to (1) compare rate-limited leaching in column and lysimeter experiments, (2) investigate the relevance of sorption to air-water interfaces (AWI), and (3) examine colloid-facilitated transport as a process explaining early experimental breakthrough. A continuum model (CM) with two-domain sorption is used to simulate equilibrium and rate-limited sorption. A random walk particle tracking (PT) model was developed and applied to analyze complex leaching characteristics. Results show that sorption parameters derived from column experiments underestimate long-term PFOA leaching in lysimeter experiments due to early depletion, suggesting that transformation of precursors contributes to the observed long-term leaching in the lysimeters (approximately 0.003 µg/kg/d PFOA). Both models demonstrate that sorption to AWI is the dominant retention mechanism for PFOS in lysimeter experiments, with retardation due to AWI being 3 (CM) to 3.7 (PT) times higher than retardation due to solid phase sorption. Notably, despite a simplified conception of AWI sorption, the PT results are closer to the observations. The PT simulations demonstrate possible colloid-facilitated transport at early time; however, results using substance-specific varying transport parameters align better with the observations, which should be equal if colloid-facilitated transport without additional kinetics is the sole mechanism affecting early breakthrough. Possibly, rate-limited sorption to AWI is relevant during the early stages of the lysimeter experiment. Our findings demonstrate that rate-limited sorption is less relevant for long-term leaching under field conditions compared to transformation of precursors and that sorption to AWI can be the dominant retention mechanism on contaminated sites. Moreover, they highlight the potential of random walk particle tracking as a practical alternative to continuum models for estimating the relative contributions of various retention mechanisms.

Hydrothermal Alkaline Treatment (HALT) of Foam Fractionation Concentrate Derived from PFAS-Contaminated Groundwater

While foam fractionation (FF) process has emerged as a promising technology for removal of per- and polyfluoroalkyl substances (PFASs) from contaminated groundwater, management of the resulting foam concentrates with elevated concentrations of PFASs (e.g., >1 g/L) remains a challenge. Here, we applied hydrothermal alkaline treatment (HALT) to two foam concentrates derived from FF field demonstration projects that treated aqueous film-forming foam (AFFF)-impacted groundwater. Results showed >90% degradation and defluorination within 90 min of treatment (350 °C, 1 M NaOH) of all 62 PFASs (including cations, anions, and zwitterions) identified in foam concentrates. Observed rate constants for degradation of individual perfluoroalkyl sulfonates (PFSAs, CnF2n+1-SO3-), the most recalcitrant class of PFASs, in both foam concentrates were similar to values measured previously in other aqueous matrices, indicating that elevated initial PFAS concentrations (e.g., PFHxSinit = 0.55 g/L), dissolved organic carbon (DOC; up to 4.5 g/L), and salt levels (e.g., up to 325 mg/L chloride) do not significantly affect PFAS reaction kinetics. DOC was partially mineralized by treatment, but a fraction (∼15%) was recalcitrant. Spectroscopic characterization revealed molecular features of the HALT-recalcitrant DOC fraction, and nontarget high-resolution mass spectrometry tentatively identified 129 nonfluorinated HALT-recalcitrant molecules. Analysis of process energy requirements shows that treating PFAS-contaminated foam concentrates with HALT would add minimally (<5%) to the overall energy requirements of an integrated FF-HALT treatment train.

Occurrence of per- and polyfluorinated alkyl substances in wastewater treatment plants in Northern Italy

Wastewater treatment plants are known to be relevant input sources of per- and polyfluoroalkyl substances (PFAS) in the aquatic environment. This study aimed to investigate the occurrence, fate, and seasonal variability of twenty-five PFAS in four municipal wastewater treatment plants (WWTP A, B, C, and D) surrounding the city of Milan (Northern, Italy). Composite 24-h wastewater samples were collected in July and October 2021 and May and February 2022 from influents and effluents of the four WWTPs. PFAS were detected at concentrations ranging between 24.1 and 66.9 μg L-1 for influent and 13.4 and 107 μg L-1 for effluent wastewater samples. Perfluoropentanoic acid was the most abundant (1.91-30.0 μg L-1) in influent samples, whereas perfluorobutane sulfonic acid predominated (0.80-66.1 μg L-1) in effluent samples. In sludge, PFOA was detected in plant A at concentrations in the range of 96.6-165 ng kg-1 dw in primary sludge samples and 98.6-440 ng kg-1 dw in secondary treatment sludge samples. The removal efficiency of total PFAS varied between 6 % and 96 %. However, an increase of PFAS concentrations was observed from influents to effluents for plant D (during July and October), plant A (during October and May), and plant C (during May) indicating that biotransformation of PFAS precursors can occur during biological treatments. This was supported by the observed increase in concentrations of PFOA from primary to secondary treatment sludge samples in plant A. Moreover, the plant operating at shorter hydraulic retention times (plant D) showed lower removal efficiency (<45 %). Seasonal variation of PFAS in influent and effluent appears rather low and more likely due to pulse release instead of seasonal factors.

Factors Affecting the Adsorption of Per- and Polyfluoroalkyl Substances (PFAS) by Colloidal Activated Carbon

The immobilization of per- and polyfluoroalkyl substances (PFAS) by colloidal activated carbon (CAC) barriers has been proposed as a potential in-situ method to mitigate the transport of plumes of PFAS in the subsurface. However, if PFAS are continuously released from a source zone, the adsorptive sites on CAC will eventually become saturated, upon which point the breakthrough of PFAS in the barrier will occur. To predict the long-term effectiveness of CAC barriers, it is important to evaluate the factors that may affect the adsorption of PFAS on CAC. In this study, the adsorption of 7 PFAS on a polymer-stabilized CAC (i.e., PlumeStop®) and on a polymer-free CAC was investigated using batch experiments. The adsorption affinity of PFAS to CAC was in the following order: PFOS > 6:2 FTS > PFHxS > PFOA > PFBS > PFPeA > PFBA. This result indicates that hydrophobic interaction was the predominant adsorption mechanism, and that hydrophilic compounds such as PFBA and PFPeA will break through CAC barriers first. The partition coefficient Kd for the adsorption of PFAS on the polymer-stabilized CAC was 1.3 - 3.5 times smaller than the Kd for the adsorption of PFAS on the polymer-free CAC, suggesting that the polymers decreased the adsorption, presumably due to competitive sorption. Thus, the PFAS adsorption capacity of PlumeStop CAC barriers is expected to increase once the polymers are biodegraded and/or washed away. The affinity of PFOS and PFOA to CAC increased when the ionic strength of the solution increased from 1 to 100 mM, or when the concentration of Ca2+ increased from 0 to 2 mM. In contrast, less PFOS and PFOA were adsorbed in the presence of 1 - 20 mgC/L Suwannee River Fulvic Acid, which represented dissolved organic carbon, or in the presence of 10 - 100 mg/L diethylene glycol butyl ether (DGBE), which is an important component in some aqueous film-forming foam (AFFF) formulations. The presence of 0.5 - 4.8 mg/L benzene or 0.5 - 8 mg/L trichloroethylene, the co-contaminants that may comingle with PFAS at AFFF-impacted sites, diminished PFOS adsorption but had no effect or even slightly enhanced PFOA adsorption. When the initial concentration of TCE was 8 mg/L, the Kd (514 ± 240 L/g) for the adsorption of PFOS was approximately 20 times lower than that in the TCE-free system (Kd = 9,579 ± 829 L/g). The results of this study provided insights into some key factors that may affect the adsorption of PFAS in in-situ CAC barriers.

Spatio-temporal trends in livestock exposure to per- and polyfluoroalkyl substances (PFAS) inform risk assessment and management measures

The migration of per- and polyfluoroalkyl substances (PFAS) onto agricultural properties has resulted in the accumulation of PFAS in livestock. The environmental determinants of PFAS accumulation in livestock from the grazing environment are poorly understood, resulting in limited capacity to manage livestock exposure and subsequent transfer of PFAS through the food chain. Analytical- (n = 978 samples of soil, water, pasture, and serum matrices), farm management/practice- and livestock physiology data were collated and interrogated from environmental PFAS investigations across ten farms, from four agro-ecological regions of Victoria (Australia). Statistical analysis identified perfluorooctane sulfonate (PFOS) and perfluorohexane sulfonate (PFHxS) as key analytes of concern for livestock bioaccumulation. PFOS and PFHxS concentrations in livestock drinking water were positively correlated with serum concentrations while other intake pathways (pasture and soil) had weaker correlations. Seasonal trends in PFAS body burden (serum concentrations) were identified and suggested to be linked to seasonal grazing behaviours and physiological water requirements. The data showed for the first time that livestock exposure to PFAS is dynamic and with relatively short elimination half-lives, there is opportunity for exposure management. Meat from cattle, grazed on PFAS impacted sites, may exceed health-based guideline values for PFAS, especially for markets with low limits (like the European Commission Maximum Limits or EC MLs). This study found that sites with mean livestock drinking water concentrations as low as 0.003 μg PFOS/L may exceed the EC ML for PFOS in cattle meat. Risk assessment can be used to prioritise site cleanup and development of management plans to reduce PFAS body burden by considering timing of stock rotation and/or supplementation of primary exposure sources.

Enhancement of perfluorooctanoic acid and perfluorooctane sulphonic acid removal in constructed wetland using iron mineral: Performance and mechanisms

Polyfluoroalkyl substance (PFAS) pose a threat to the aquatic environment due to their environmental persistence. The removal of PFAS using constructed wetlands (CWs) has received interest, but the adsorption saturation and limited removal capacity of the substrate is frequently challenging. To enhance the microbial degradation and performance of the substrate, different configurations of iron minerals were used as substrate to remove perfluorooctane sulphonic acid (PFOS) and perfluorooctanoic acid (PFOA) from CWs. The addition of iron minerals resulted in elimination of 57.2% and 63.9% of PFOS and PFOA in the effluent, respectively, which were 35.0% and 36.8% higher than that of control. Moreover, up to 85.4%, 86%, and 85.1% of NH₄⁺, NO₃^-, and phosphorus, respectively, was removed using iron minerals. The enhanced electron transfer in iron mineral-based CWs was confirmed by a 61.2% increase in cytochrome C reductase content and an increased Fe(III)/Fe(II) ratio. Microbial analysis showed that the proportions of microbes with PFAS removal capacity (e.g. Burkholderiae and Pseudomonas), and the key pathways of the TCA cycle and glycolysis were increased in iron mineral-based CW. Based on these findings, we conclude that supplementation with iron mineral could enhance PFOA and PFOS removal in CWs.

Influence of microbial weathering on the partitioning of per- and polyfluoroalkyl substances (PFAS) in biosolids

Per- and polyfluoroalkyl substances (PFAS) are a large group of man-made fluorinated organic chemicals that can accumulate in the environment. In water resource recovery facilities (WRRFs), some commonly detected PFAS tend to partition to and concentrate in biosolids where they can act as a source to ecological receptors and may leach to groundwater when land-applied. Although biosolids undergo some stabilization to reduce pathogens before land application, they still contain many microorganisms, contributing to the eventual decomposition of different components of the biosolids. This work demonstrates ways in which microbial weathering can influence biosolids decomposition, degrade PFAS, and impact PFAS partitioning in small-scale, controlled laboratory experiments. In the microbial weathering experiments, compound-specific PFAS biosolids-water partitioning coefficients (K_d) were demonstrated to decrease, on average, 0.4 logs over the course of the 91 day study, with the most rapid changes occurring during the first 10 days. Additionally, the highest rates of lipid, protein, and organic matter removal occurred during the same time. Among the evaluated independent variables, statistical analyses demonstrated that the most significant solids characteristics that impacted PFAS partitioning were organic matter, proteins, lipids, and molecular weight of organics. A multiple linear regression model was built to predict PFAS partitioning behavior in biosolids based on solid characteristics of the biosolids and PFAS characteristics with a R² value of 0.7391 when plotting predicted and measured log K_d. The findings from this work reveal that microbial weathering can play a significant role in the eventual fate and transport of PFAS and their precursors from biosolids.

Total Oxidizable Precursor (TOP) Assay-Best Practices, Capabilities and Limitations for PFAS Site Investigation and Remediation

The comprehensive characterization of per- and polyfluoroalkyl substances (PFASs) is necessary for the effective assessment and management of risk at contaminated sites. While current analytical methods are capable of quantitatively measuring a number of specific PFASs, they do not provide a complete picture of the thousands of PFASs that are utilized in commercial products and potentially released into the environment. These unmeasured PFASs include many PFAS precursors, which may be converted into related PFAS chemicals through oxidation. The total oxidizable precursor (TOP) assay offers a means of bridging this gap by oxidizing unknown PFAS precursors and intermediates and converting them into stable PFASs with established analytical standards. The application of the TOP assay to samples from PFAS-contaminated sites has generated several new insights, but it has also presented various technical challenges for laboratories. Despite the increased number of literature studies that include the TOP assay, there is a critical and growing gap in the application of this method beyond researchers in academia. This article outlines the benefits and challenges of using the TOP assay with aqueous samples for site assessments and suggests ways to address some of its limitations.

Perfluoroalkyl substance pollution: detecting and visualizing emerging trends based on CiteSpace

In recent years, perfluoroalkyl substances (PFASs) have been detected in all kinds of environmental media and can harm animals and human beings. They have attracted the attention of environmental workers worldwide and have become another research hotspot in the field of environment. However, analyses of PFASs have seldom been studied systematically. Therefore, this study summarizes the available data in 6756 publications (2000-2022) using the CiteSpace software to provide insights into the specific characteristics of PFASs and consequently shows global development trends that scientists can use for establishing future research directions. As opposed to traditional review articles by experts, this study provides a new method for quantitatively visualizing information about the development of this field over the past 23 years. Results show that the countries with more research in this field are mainly the USA and China. The research on PFASs is mainly concentrated in environmental sciences and ecology. Zhanyun Wang and Robert C. Buck's research has the highest influence rate in this field, and their research group is worthy of attention. Through the analysis of hot keywords, we conclude that the research hotspots are mainly focused on PFASs' transmission media and pathways, human exposure and the mechanism of toxicity, and degradation and remediation measures. Collectively these results indicate the major themes of PFAS research are as follows: (1) transmission media and pathways, (2) human exposure and the mechanism of toxicity, (3) degradation and remediation measures. This study maps the major research domains of PFAS research; explanations and implications of the findings are discussed; and emerging trends highlighted.

Biotransformation of 8:2 Fluorotelomer Alcohol in Soil from Aqueous Film-Forming Foams (AFFFs)-Impacted Sites under Nitrate-, Sulfate-, and Iron-Reducing Conditions

The environmental fate of per- and polyfluoroalkyl substances (PFAS) in aqueous film-forming foams (AFFFs) remains largely unknown, especially under the conditions representative of natural subsurface systems. In this study, the biotransformation of 8:2 fluorotelomer alcohol (8:2 FTOH), a component of new-generation AFFF formulations and a byproduct in fluorotelomer-based AFFFs, was investigated under nitrate-, iron-, and sulfate-reducing conditions in microcosms prepared with AFFF-impacted soils. Liquid chromatography-tandem mass spectrometry (LC-MS/MS) and high-resolution mass spectrometry (HRMS) were employed to identify biotransformation products. The biotransformation was much slower under sulfate- and iron-reducing conditions with >60 mol % of initial 8:2 FTOH remaining after ∼400 days compared to a half-life ranging from 12.5 to 36.5 days under nitrate-reducing conditions. Transformation products 8:2 fluorotelomer saturated and unsaturated carboxylic acids (8:2 FTCA and 8:2 FTUA) were detected under all redox conditions, while 7:2 secondary fluorotelomer alcohol (7:2 sFTOH) and perfluorooctanoic acid (PFOA) were only observed as transformation products under nitrate-reducing conditions. In addition, 1H-perfluoroheptane (F(CF₂)₆CF₂H) and 3-F-7:3 acid (F(CF₂)₇CFHCH₂COOH) were identified for the first time during 8:2 FTOH biotransformation. Comprehensive biotransformation pathways for 8:2 FTOH are presented, which highlight the importance of accounting for redox condition and the related microbial community in the assessment of PFAS transformations in natural environments.

Biotransformation of 6:2 Fluorotelomer Thioether Amido Sulfonate in Aqueous Film-Forming Foams under Nitrate-Reducing Conditions

Despite the prevalence of nitrate reduction in groundwater, the biotransformation of per- and polyfluoroalkyl substances (PFAS) under nitrate-reducing conditions remains mostly unknown compared with aerobic or strong reducing conditions. We constructed microcosms under nitrate-reducing conditions to simulate the biotransformation occurring at groundwater sites impacted by aqueous film-forming foams (AFFFs). We investigated the biotransformation of 6:2 fluorotelomer thioether amido sulfonate (6:2 FtTAoS), a principal PFAS constituent of several AFFF formulations using both quantitative liquid chromatography-tandem mass spectrometry (LC-MS/MS) and qualitative high-resolution mass spectrometry analyses. Our results reveal that the biotransformation rates of 6:2 FtTAoS under nitrate-reducing conditions were about 10 times slower than under aerobic conditions, but about 2.7 times faster than under sulfate-reducing conditions. Although minimal production of 6:2 fluorotelomer sulfonate and the terminal perfluoroalkyl carboxylate, perfluorohexanoate was observed, fluorotelomer thioether and sulfinyl compounds were identified in the aqueous samples. Evidence for the formation of volatile PFAS was obtained by mass balance analysis using the total oxidizable precursor assay and detection of 6:2 fluorotelomer thiol by gas chromatography-mass spectrometry. Our results underscore the complexity of PFAS biotransformation and the interactions between redox conditions and microbial biotransformation activities, contributing to the better elucidation of PFAS environmental fate and impact.

Neutral Per- and Polyfluoroalkyl Substances, Butyl Carbitol, and Organic Corrosion Inhibitors in Aqueous Film-Forming Foams: Implications for Vapor Intrusion and the Environment

Per- and polyfluoroalkyl substances (PFAS), butyl carbitol, and corrosion inhibitors are components of aqueous film-forming foams (AFFFs). Volatile (neutral) fluorotelomerization (FT)- and electrochemical fluorination (ECF)-based PFAS, butyl carbitol, and organic corrosion inhibitors were quantified in 39 military specification (MilSpec), non-MilSpec, and alcohol resistant-AFFF concentrates (undiluted) from 1974 to 2010. Fluorotelomer alcohols were found only in FT-based AFFFs and N-methyl- and N-ethyl-perfluoroalkyl sulfonamides, and sulfonamido ethanols were found only in ECF-based AFFFs. Neutral PFAS and benzotriazole, 4-methylbenzotriazole, and 5-methybenzotriazole occurred at mg/L levels in the AFFFs, while butyl carbitol occurred at g/L levels. Neutral PFAS concentrations in indoor air due to vapor intrusion of a nearby undiluted AFFF release are estimated to be anywhere from 2 to >10 orders of magnitude higher than documented background indoor air concentrations. Estimated butyl carbitol and organic corrosion inhibitor concentrations were lower than and comparable to indoor concentrations recently measured, respectively. The wide range of neutral PFAS concentrations and Henry's law constants indicate that field, soil-gas measurements are needed to validate the estimations. Co-discharged butyl carbitol likely contributes to oxygen depletion in AFFF-impacted aquifers and may hinder the natural PFAS aerobic biotransformation. Organic corrosion inhibitors in AFFFs indicate that these are another source of corrosion inhibitors in the environment.

Assessment of Mobilization Potential of Per- and Polyfluoroalkyl Substances for Soil Remediation

This study investigated the mobilization of a wide range of per- and polyfluoroalkyl substances (PFASs) present in aqueous film-forming foams (AFFFs) in water-saturated soils through one-dimensional (1-D) column experiments with a view to assessing the feasibility of their remediation by soil desorption and washing. Results indicated that sorption/desorption of most of the shorter-carbon-chain PFASs (C ≤ 6) in soil reached greater than 99% rapidly─after approximately two pore volumes (PVs) and were well predicted by an equilibrium transport model, indicating that they will be readily removed by soil washing technologies. In contrast, the equilibrium model failed to predict the mobilization of longer-chain PFASs (C ≥ 7), indicating the presence of nonequilibrium sorption/desorption (confirmed by a flow interruption experiment). The actual time taken to attain 99% sorption/desorption was up to 5 times longer than predicted by the equilibrium model (e.g., ∼62 PVs versus ∼12 PVs predicted for perfluorooctane sulfonate (PFOS) in loamy sand). The increasing contribution of hydrophobic interactions over the electrostatic interactions is suggested as the main driving factor of the nonequilibrium processes. The inverse linear relationship (R² = 0.6, p < 0.0001) between the nonequilibrium mass transfer rate coefficient and the Freundlich sorption coefficient could potentially be a useful means for preliminary evaluation of potential nonequilibrium sorption/desorption of PFASs in soils.

Microbial biotransformation of aqueous film-forming foam derived polyfluoroalkyl substances

Per- and polyfluoroalkyl substances (PFASs) used in aqueous film-forming foam (AFFF) comprise some perfluoroalkyl substances but a larger variety of polyfluoroalkyl substances. Despite their abundance in AFFF, information is lacking on the potential transformation of these polyfluoroalkyl substances. Due to the biological and chemical stability of the repeating perfluoroalkyl -(CF₂)_n- moiety common to all known AFFF-derived PFASs, it is not immediately evident whether the microbial biotransformation mechanisms observed for other organic contaminants also govern the microbial biotransformation of polyfluoroalkyl substances. Herein, we aim to: 1) review the literature on the aerobic or anaerobic microbial biotransformation of AFFF-derived polyfluoroalkyl substances in environmental media; 2) compile and summarize proposed microbial biotransformation pathways for major classes of polyfluoroalkyl substances; 3) identify the dominant biotransformation intermediates and terminal biotransformation products; and 4) discuss these findings in the context of environmental monitoring and source allocation. This analysis revealed that much more is currently known about aerobic microbial biotransformation of polyfluoroalkyl substances, as compared to anaerobic biotransformation. Further, there are some similarities in microbial biotransformations of fluorotelomer and electrochemical fluorination-derived polyfluoroalkyl substances, but differences may be largely due to head group composition. Dealkylation, oxidation, and hydrolytic reactions appear to be particularly important for microbial biotransformation of AFFF-derived polyfluoroalkyl substances, and these biotransformations may lead to formation of some semi-stable intermediates. Finally, this review discusses key knowledge gaps and opportunities for further research.

Application of Hydrothermal Alkaline Treatment for Destruction of Per- and Polyfluoroalkyl Substances in Contaminated Groundwater and Soil

Hydrothermal alkaline treatment (HALT) can effectively degrade per- and polyfluoroalkyl substances (PFASs) present in aqueous film-forming foam (AFFF). However, information is lacking regarding the treatment of PFASs in actual groundwater and soil from AFFF-impacted sites, especially for complex soil matrices. Given the lack of studies on direct soil treatment for PFAS destruction, we herein applied HALT to two groundwater samples and three soil samples from AFFF-impacted sites and characterized the destruction of PFASs using high-resolution mass spectrometry. Results showed that the 148 PFASs identified in all collected field samples, including 10 cationic, 98 anionic, and 40 zwitterionic PFASs, were mostly degraded to nondetectable levels within 90 min when treated with 5 M NaOH at 350 °C. The near-complete defluorination, as evidenced by fluoride release measurements, confirmed the complete destruction of PFASs. While many structures, including perfluoroalkyl carboxylic acids and polyfluorinated substances, were readily degraded, perfluoroalkyl sulfonates (PFSAs, C_nF_2n+1-SO₃^-), most notably with short chain lengths (n = 3-5), were more recalcitrant. Rates of PFSA destruction in groundwater samples were similar to those measured in laboratory water solutions, but reactions in soil were slow, presumably due to base-neutralizing properties of the soil. Further, the degradation of PFASs in groundwaters and soils was found to be a function of reaction temperature, NaOH concentration, and reaction time. These findings have important implications for the remediation of AFFF-impacted sites.

Transport and fate of aqueous film forming foam in an urban estuary

The deployment of aqueous film forming foams (AFFF) used for firefighting during emergencies and training often releases per- and polyfluoroalkyl substances (PFAS) into the environment. In October 2018, first responders in Providence, RI, USA applied an AFFF during a fuel spill. Due to the proximity of the incident to the upper reaches of Narragansett Bay (NB), an unknown quantity of gasoline and AFFF entered the estuary via surface runoff and stormwater drains. Water samples near the spill were collected approximately 15 h after the incident and analyzed for 24 PFAS. Minor increases in measured PFAS concentrations were observed relative to pre- and post-spill samples at monitoring sites near the incident, except 6:2-fluorotelomer sulfonate (6:2-FTS) that peaked post-spill (max 311 ng/L). After performing the total oxidizable precursor (TOP) assay on water samples and the AFFF concentrate, significant increases in perfluorocarboxylic acids (PFCAs) were observed. One compound, 6:2 fluorotelomer mercaptoalkylamido sulfonate (6:2-FTSAS), was identified as a major component of the AFFF used. Peak areas of 6:2-FTSAS and the degradation product 6:2-FTSAS-sulfoxide corresponded to observed increases in the TOP assay results and were useful as tracers of AFFF in surrounding waters. Elevated levels of PFAS at the time of sampling were limited to a confined area of the Providence River due to river flow and tidal action. Observed concentrations were also compared to hydrodynamic model results, and results confirmed rapid dissipation of AFFF components with distance from the spill. However, modeled results did not capture possible secondary releases of AFFF from local municipal stormwater and sewer infrastructure, as observational data suggest. The multiple lines of evidence of PFAS present in surface waters permitted a better assessment of the potential environmental impacts from products such as AFFF for which the chemical composition is largely unknown.

Aerobic BTEX biodegradation increases yield of perfluoroalkyl carboxylic acids from biotransformation of a polyfluoroalkyl surfactant, 6:2 FtTAoS

Aqueous film-forming foams (AFFFs) are important sources of per- and polyfluoroalkyl substances (PFASs) in soil, groundwater, and surface water. Soil microorganisms can convert polyfluorinated substances into persistent perfluoroalkyl acids, but the understanding of co-contaminant stimulation or inhibition of PFASs biotransformation is limited. In this study, we investigate how aerobic biotransformation of polyfluorinated substances was affected by common AFFF co-contaminants, such as gasoline aromatics: benzene, toluene, ethylbenzene, and o-xylene (BTEX). We performed aerobic microcosm studies by inoculating AFFF-impacted soil with medium containing 6:2 fluorotelomer thioether amido sulfonate (FtTAoS) and either diethyl glycol monobutyl ether (DGBE), a common AFFF ingredient, or BTEX compounds as the main carbon and energy source. BTEX-amended microcosms produced 4.3-5.3 fold more perfluoroalkyl carboxylates (PFCAs) than DGBE-amended ones, even though both organic carbon sources induced similar 6:2 FtTAoS biotransformation rates. In enrichments of AFFF-impacted solids selecting for BTEX biodegradation, we detected the presence of genes encoding toluene dioxygenase as well as larger abundances of transformation products from thioether oxidation that complement larger quantities of terminal transformation products. Our findings indicate that enrichment of BTEX-degrading microorganisms in the AFFF-impacted soil enhanced the conversion of 6:2 FtTAoS to PFCAs. These results provide insights into the high ratio of PFAAs to precursors at AFFF-impacted sites with history of BTEX bioremediation.

Per- and polyfluoroalkyl substances in the environment

Over the past several years, the term PFAS (per- and polyfluoroalkyl substances) has grown to be emblematic of environmental contamination, garnering public, scientific, and regulatory concern. PFAS are synthesized by two processes, direct fluorination (e.g., electrochemical fluorination) and oligomerization (e.g., fluorotelomerization). More than a megatonne of PFAS is produced yearly, and thousands of PFAS wind up in end-use products. Atmospheric and aqueous fugitive releases during manufacturing, use, and disposal have resulted in the global distribution of these compounds. Volatile PFAS facilitate long-range transport, commonly followed by complex transformation schemes to recalcitrant terminal PFAS, which do not degrade under environmental conditions and thus migrate through the environment and accumulate in biota through multiple pathways. Efforts to remediate PFAS-contaminated matrices still are in their infancy, with much current research targeting drinking water.

Surface-water/groundwater boundaries affect seasonal PFAS concentrations and PFAA precursor transformations

Elevated concentrations of per- and polyfluoroalkyl substances (PFAS) in drinking-water supplies are a major concern for human health. It is therefore essential to understand factors that affect PFAS concentrations in surface water and groundwater and the transformation of perfluoroalkyl acid (PFAA) precursors that degrade into terminal compounds. Surface-water/groundwater exchange can occur along the flow path downgradient from PFAS point sources and biogeochemical conditions can change rapidly at these exchange boundaries. Here, we investigate the influence of surface-water/groundwater boundaries on PFAS transport and transformation. To do this, we conducted an extensive field-based analysis of PFAS concentrations in water and sediment from a flow-through lake fed by contaminated groundwater and its downgradient surface-water/groundwater boundary (defined as ≤100 cm below the lake bottom). PFAA precursors comprised 45 ± 4.6% of PFAS (PFAA precursors + 18 targeted PFAA) in the predominantly oxic lake impacted by a former fire-training area and historical wastewater discharges. In shallow porewater downgradient from the lake, this percentage decreased significantly to 25 ± 11%. PFAA precursor concentrations decreased by 85% between the lake and 84-100 cm below the lake bottom. PFAA concentrations increased significantly within the surface-water/groundwater boundary and in downgradient groundwater during the winter months despite lower stable concentrations in the lake water source. These results suggest that natural biogeochemical fluctuations associated with surface-water/groundwater boundaries may lead to PFAA precursor loss and seasonal variations in PFAA concentrations. Results of this work highlight the importance of dynamic biogeochemical conditions along the hydrological flow path from PFAS point sources to potentially affected drinking water supplies.

Environmental Sources, Chemistry, Fate, and Transport of Per- and Polyfluoroalkyl Substances: State of the Science, Key Knowledge Gaps, and Recommendations Presented at the August 2019 SETAC Focus Topic Meeting

A Society of Environmental Toxicology and Chemistry (SETAC) Focused Topic Meeting (FTM) on the environmental management of per- and polyfluoroalkyl substances (PFAS) convened during August 2019 in Durham, North Carolina (USA). Experts from around the globe were brought together to critically evaluate new and emerging information on PFAS including chemistry, fate, transport, exposure, and toxicity. After plenary presentations, breakout groups were established and tasked to identify and adjudicate via panel discussions overarching conclusions and relevant data gaps. The present review is one in a series and summarizes outcomes of presentations and breakout discussions related to (1) primary sources and pathways in the environment, (2) sorption and transport in porous media, (3) precursor transformation, (4) practical approaches to the assessment of source zones, (5) standard and novel analytical methods with implications for environmental forensics and site management, and (6) classification and grouping from multiple perspectives. Outcomes illustrate that PFAS classification will continue to be a challenge, and additional pressing needs include increased availability of analytical standards and methods for assessment of PFAS and fate and transport, including precursor transformation. Although the state of the science is sufficient to support a degree of site-specific and flexible risk management, effective source prioritization tools, predictive fate and transport models, and improved and standardized analytical methods are needed to guide broader policies and best management practices. Environ Toxicol Chem 2021;40:3234-3260. © 2021 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.

Perfluoroalkyl acids on suspended particles: Significant transport pathways in surface runoff, surface waters, and subsurface soils

Eroded particles from the source zone could transport a high concentration of perfluoroalkyl acids (PFAAs) to sediments and water bodies. Yet, the contribution of suspended particles has not been systematically reviewed. Analyzing reported studies, we quantitatively demonstrate that suspended particles in surface water can contain significantly higher concentrations of PFAAs than the sediment below, indicating the source of suspended particles are not the sediment but particles eroded and carried from the source zone upstream. The affinity of PFAAs to particles depends on the particle composition, including organic carbon fraction and iron or aluminum oxide content. In soils, most PFAAs are retained within the top 5 m below the ground surface. The distribution of PFAAs in the subsurface varies based on site properties and local weather conditions. The depth corresponding to the maximum concentration of PFAA in soil decreases with an increase in soil organic carbon or rainfall amount received in the catchment areas. We attribute a greater accumulation of PFAAs near the upper layer of the subsurface to an increase in the accumulation of particles eroded from source zones upstream receiving heavy rainfall. Precursor transformation in the aerobic zone is significantly higher than in the anaerobic zone, thereby making the aerobic subsurface zone serve as a long-term source of groundwater pollution. Collectively, these results suggest that suspended particles, often an overlooked vector for PFAAs, can be a dominant pathway for the transport of PFAAs in environments.

Environmental Source Tracking of Per- and Polyfluoroalkyl Substances within a Forensic Context: Current and Future Techniques

The source tracking of per- and polyfluoroalkyl substances (PFASs) is a new and increasingly necessary subfield within environmental forensics. We define PFAS source tracking as the accurate characterization and differentiation of multiple sources contributing to PFAS contamination in the environment. PFAS source tracking should employ analytical measurements, multivariate analyses, and an understanding of PFAS fate and transport within the framework of a conceptual site model. Converging lines of evidence used to differentiate PFAS sources include: identification of PFASs strongly associated with unique sources; the ratios of PFAS homologues, classes, and isomers at a contaminated site; and a site's hydrogeochemical conditions. As the field of PFAS source tracking progresses, the development of new PFAS analytical standards and the wider availability of high-resolution mass spectral data will enhance currently available analytical capabilities. In addition, multivariate computational tools, including unsupervised (i.e., exploratory) and supervised (i.e., predictive) machine learning techniques, may lead to novel insights that define a targeted list of PFASs that will be useful for environmental PFAS source tracking. In this Perspective, we identify the current tools available and principal developments necessary to enable greater confidence in environmental source tracking to identify and apportion PFAS sources.

Fate and transport of per- and polyfluoroalkyl substances (PFASs) in the vadose zone

Per- and polyfluoroalkyl substances (PFASs) are a heterogeneous group of persistent organic pollutants that have been detected in various environmental compartments around the globe. Emerging research has revealed the preferential accumulation of PFASs in shallow soil horizons, particularly at sites impacted by firefighting activities, agricultural applications, and atmospheric deposition. Once in the vadose zone, PFASs can sorb to soil, accumulate at interfaces, become volatilized, be taken up in biota, or leach to the underlying aquifer. At the same time, polyfluorinated precursor species may transform into highly recalcitrant perfluoroalkyl acids, changing their chemical identity and thus transport behavior along the way. In this review, we critically discuss the current state of the knowledge and aim to interconnect the complex processes that control the fate and transport of PFASs in the vadose zone. Furthermore, we identify key challenges and future research needs. Consequently, this review may serve as an interdisciplinary guide for the risk assessment and management of PFAS-contaminated sites.

Determination of total oxidizable precursors in foam surfactants and foam contaminated water based on UV-activated persulfate oxidation

In this study, ultraviolet (UV)-activated persulfate under alkaline condition was developed as an alternative Total Oxidizable Precursor (TOP) assay to convert per- and polyfluoroalkyl substances (PFASs) precursors into detectable perfluoroalkyl acids (PFAAs). The conventional heat-based TOP assay takes 6 h at 85 °C, which is time consuming and may lose the volatile PFASs. Shorter time treatment would be beneficial to promote the analysis efficiency of the samples. We here report the UV-based TOP method as faster replacement of conventional heat-based TOP assay. The 6:2 fluorotelomer sulfonate (FTS), 8:2 FTS, and perfluorooctanesulfonamide (FOSA) achieved nearly complete conversion (with the molar yield of PFAAs of 97.2%-109.9%) at 60 min. This new UV-based TOP assay was then applied to 23 industry samples, and the results are comparable with the heat-based TOP assay. The perfluoroalkyl carboxylic acids (PFCAs) concentrations of 23 samples before and after normal TOP assay were 0-4290 mg L^-1 and 438-77,420 mg L^-1, respectively. The PFCAs after 60 min UV-based TOP assay was 310-81,881 mg L^-1. The Quotient_Mol of 21 samples were 0.71-1.28, the Quotient_Mol of other two samples were 1.45 and 1.68, this probably due to the loss of volatile precursors during heat-based TOP assay. The UV-based TOP assay is an efficient, reliable and faster alternative to the conventional heat-based TOP assay.

Hydrothermal Alkaline Treatment for Destruction of Per- and Polyfluoroalkyl Substances in Aqueous Film-Forming Foam

The widespread use of aqueous film-forming foam (AFFF) for firefighting activities (e.g., fire training to extinguish fuel-based fires at aircraft facilities) has led to extensive groundwater and soil contamination by per- and polyfluoroalkyl substances (PFASs) that are highly recalcitrant to destruction using conventional treatment technologies. This study reports on the hydrothermal alkaline treatment of diverse PFASs present in AFFFs. Quantitative and semiquantitative high-resolution mass spectrometry analyses of PFASs demonstrate a rapid degradation of all 109 PFASs identified in two AFFFs (sulfonate- and fluorotelomer-based formulations) in water amended with an alkali (e.g., 1-5 M NaOH) at near-critical temperature and pressure (350 °C, 16.5 MPa). This includes per- and polyfluoroalkyl acids and a range of acid precursors. Most PFASs were degraded to nondetectable levels within 15 min, and the most recalcitrant perfluoroalkyl sulfonates were degraded within 30 min when treated with 5 M NaOH. ¹⁹F NMR spectroscopic analysis and fluoride ion analysis confirm the near-complete defluorination of PFASs in both dilute and concentrated AFFF mixtures, and no stable volatile organofluorine species were detected in reactor headspace gases by the gas chromatography-mass spectrometry analysis. These findings indicate a significant potential for application of hydrothermal treatment technologies to manage PFAS waste streams, including on-site treatment of unused AFFF chemical stockpiles, investigation-derived wastes, and concentrated source zone materials.

A critical review of modeling Poly- and Perfluoroalkyl Substances (PFAS) in the soil-water environment

Due to their health effects and the recalcitrant nature of their CF bonds, Poly- and Perfluoroalkyl Substances (PFAS) are widely investigated for their distribution, remediation, and toxicology in ecosystems. However, very few studies have focused on modeling PFAS in the soil-water environment. In this review, we summarized the recent development in PFAS modeling for various chemical, physical, and biological processes, including sorption, volatilization, degradation, bioaccumulation, and transport. PFAS sorption is kinetic in nature with sorption equilibrium commonly quantified by either a linear, the Freundlich, or the Langmuir isotherms. Volatilization of PFAS depends on carbon chain length and ionization status and has been simulated by a two-layer diffusion process across the air water interface. First-order kinetics is commonly used for physical, chemical, and biological degradation processes. Uptake by plants and other biota can be passive and/or active. As surfactants, PFAS have a tendency to be sorbed or concentrated on air-water or non-aqueous phase liquid (NAPL)-water interfaces, where the same three isotherms for soil sorption are adopted. PFAS transport in the soil-water environment is simulated by solving the convection-dispersion equation (CDE) that is coupled to PFAS sorption, phase transfer, as well as physical, chemical, and biological transformations. As the physicochemical properties and concentration vary greatly among the potentially thousands of PFAS species in the environment, systematic efforts are needed to identify models and model parameters to simulate their fate, transport, and response to remediation techniques. Since many process formulations are empirical in nature, mechanistic approaches are needed to further the understanding of PFAS-soil-water-plant interactions so that the model parameters are less site dependent and more predictive in simulating PFAS remediation efficiency.

Spatial Trends of Anionic, Zwitterionic, and Cationic PFASs at an AFFF-Impacted Site

Soil and groundwater from an aqueous film-forming foam (AFFF)-impacted site were sampled at high resolution (n = 105 for soil, n = 58 for groundwater) and analyzed for an extensive list of anionic, zwitterionic, and cationic poly- and perfluoroalkyl substances (PFASs). Spatial trends for perfluoroalkyl acids and many precursors enabled a better understanding of PFAS composition, transport, and transformation. All PFASs without analytical standards were semi-quantified. Summed PFAS and individual PFAS concentrations were often higher at depth than near the surface in soil and groundwater. Zwitterionic and cationic compounds composed a majority of the total PFAS mass (up to 97%) in firefighter training area (FTA) soil. Composition of PFAS class, chain length, and structural isomers changed with depth and distance from the FTA, suggesting in situ transformation and differential transport. The percentage of branched perfluorooctane sulfonate increased with depth, consistent with differential isomeric transport. However, linear perfluorooctanoic acid (PFOA) was enriched, suggesting fluorotelomer precursor transformation to linear PFOA. Perfluorohexane sulfonamide, a potential transformation product of sulfonamide-based PFASs, was present at high concentrations (maximum 448 ng/g in soil, 3.4 mg/L in groundwater). Precursor compounds may create long-term sources of perfluoroalkyl acids, although many pathways remain unknown; precursor analysis is critical for PFAS fate and transport understanding.

Rapid Characterization of Emerging Per- and Polyfluoroalkyl Substances in Aqueous Film-Forming Foams Using Ion Mobility Spectrometry-Mass Spectrometry

Aqueous film-forming foams (AFFF) are mixtures formulated with numerous hydrocarbon- and fluoro-containing surfactants. AFFF use leads to environmental releases of unknown per- and polyfluoroalkyl substances (PFAS). AFFF composition is seldom disclosed, and their use elicits concerns from both regulatory agencies and the public because PFAS are persistent in the environment and potentially associated with adverse health effects. In this study, we demonstrate the use of coupled liquid chromatography, ion mobility spectrometry, and mass spectrometry (LC-IMS-MS) to rapidly characterize both known and unknown PFAS in AFFF. Ten AFFF formulations from seven brands were analyzed using LC-IMS-MS in both negative and positive ion modes. Untargeted analysis of the formulations was followed by feature identification of PFAS-like features utilizing database matching, mass defect and homologous series evaluation, and MS/MS fragmentation experiments. Across the tested AFFF formulations, we identified 33 homologous series; only ten of these homologous series have been previously reported. Among tested AFFF, the FireStopper (n = 85) contained the greatest number of PFAS-like features and Phos-Check contained zero. This work demonstrates that LC-IMS-MS-enabled untargeted analysis of complex formulations, followed by feature identification using data-processing algorithms, can be used for rapid exposure characterization of known and putative PFAS during fire suppression-related contamination events.

A profile analysis with suspect screening of per- and polyfluoroalkyl substances (PFASs) in firefighting foam impacted waters in Okinawa, Japan

Per- and polyfluoroalkyl substances (PFASs) are a group of persistent contaminants detected in firefighting foam impacted waters. Previous studies have performed suspect and non-target screening by high-resolution mass spectrometry (HRMS) to determine the composition of PFAS contamination and to discover unknown PFASs. Here, we performed a profile analysis with suspect screening against two lists in the NORMAN Suspect List Exchange in firefighting foam impacted environmental and drinking water (n = 18) collected in Okinawa, Japan, in April 2019. Samples were analyzed by liquid chromatography (LC) quadrupole time-of-flight (QTOF) MS in electron spray ionization mode. Suspect screening returned 116 candidate PFASs with their molecular weights, functional groups, and perfluoroalkyl chain lengths. Long-chain perfluoroalkyl acids (PFAAs) and some of their precursors were specifically found around the firefighting training area. Short-chain PFAAs were assumed to be formed from precursors by environmental processes. Perfluoroalkyl sulfonamide precursors were found to be transformed to perfluoroalkyl sulfonic acids (PFSAs) in the drinking water treatment process. In contrast, biological activated carbon filtration formed perfluoroalkyl carboxylic acids (PFCAs). The PFAS profile showed that a large number of different substances needs to be considered.

Screening New Persistent and Bioaccumulative Organics in China's Inventory of Industrial Chemicals

Over a third of the world's annual chemical production and sales occur in China. Thus, knowledge of the properties of the substances produced and emitted there is important from a global perspective. The chemical Inventory of Existing Chemical Substances of China (IECSC) lists over 45 000 chemicals. When compared to the North American and European chemical inventories, 6916 substances were found to be unique to the IECSC. We retrieved structural information for 14 938 organic chemicals in the IECSC and determined their overall environmental persistence , bioaccumulation factor (BAF), and long-range transport potential (transfer efficiency) using in silico approaches with the goal of identifying new chemicals with properties that might lead to global contamination issues. Overall, 10% of the 14 938 chemicals were unique to the IECSC and their environmental persistence and BAF were statistically higher than the values for the rest of the IECSC chemicals. We prioritized 27 neutral organic compounds predicted to have prolonged environmental persistence, and high potential for bioaccumulation and long-range transport when compared with polychlorinated biphenyls as a benchmark. We also identified 69 organofluorine compounds with three or more perfluorinated moieties, unique to the IECSC. Screening approaches and results from this study help to identify and prioritize those to be considered in further environmental modeling and monitoring assessments.

Measuring Total PFASs in Water: The Tradeoff between Selectivity and Inclusivity

Millions of people around the world may be exposed to drinking water impacted by per- and polyfluoroalkyl substances (PFASs) at levels exceeding local or national advisories. Many studies indicate that the full extent of PFAS contamination is significantly underestimated when only targeted analytical methods are used. Here, we review techniques using bulk organofluorine measurement to quantify the (as of yet) unidentified fraction of PFASs. We discuss advantages and disadvantages of specific approaches and their applicability to water analysis with a focus on the tradeoff between selectivity and inclusivity, and provide suggestions for a path forward to better characterize the wide array of PFASs present in environmental samples.

Identification and Fate of Aqueous Film Forming Foam Derived Per- and Polyfluoroalkyl Substances in a Wastewater Treatment Plant

The fate of per- and polyfluoroalkyl substances (PFASs) derived from aqueous film forming foam (AFFF) was investigated within a wastewater treatment plant (WWTP) receiving large AFFF inputs from a foam refractory testing event. Targeted analysis, the Total Oxidizable Precursor Assay (TOP Assay), and nontargeted analysis with quadrupole time-of-flight (QTOF) were used to characterize the samples. Over the duration of foam testing, approximately 10.8 kg of total PFASs was measured by TOP Assay in the influent, and 6.3 kg of total PFASs was measured in the effluent; 94 g of PFOS was released in the effluent, apparently from remobilization of historical sources. 1.7% of total PFASs measured in the influent were converted to short chain perfluoroalkyl carboxylates in the effluent. Ten PFAS classes previously reported, including 6:2 fluorotelomer thioether amido sulfonate (6:2 FtTAoS), and 5 PFAS classes newly reported were identified by QTOF. The trickling filter was the only unit operation that resulted in significant gains and losses of individual PFASs, including near complete loss of 6:2 FtTAoS due to transformation. Similar reaction pathways for 6:2 FtTAoS reported in previously published soil and activated sludge microcosm experiments were observed in this WWTP, although a higher yield of perfluoroheptanoic acid was observed.