Tailored Linker Defects in UiO-67 with High Ligand-to-Metal Charge Transfer toward Efficient Photoreduction of CO2

Facile synthesis of MOF-808/RGO-based 3D macroscopic aerogel for enhanced photoreduction CO2

Three-dimensional (3D) macroscopic aerogels have emerged as a critical component in the realm of photocatalysis. Maximizing the integration of materials can result in enhanced efficiency and selectivity in photocatalytic processes. In this investigation, we fabricated MOF-808/reduced graphene oxide (RGO) 3D macroscopic aerogel composite materials employing the techniques of hydrothermal synthesis and freeze-drying. The results revealed that the macroscopic aerogel material exhibited the highest performance in CO2 reduction to CO, particularly when the concentration of RGO was maintained at 5 mg mL-1. In addition, we synthesized powder materials of MR-5 composite photocatalysts and conducted a comparative analysis in terms of photocatalytic CO2 reduction performance and electron transfer efficiency. The results showthat the macroscopic aerogel material boasts a high specific surface area, an abundant internal pore structure, and increased active sites. These attributes collectively enhance light energy utilization, and electron transfer rates, thereby, improving photothermal and photoelectric conversion efficiencies. Furthermore, we conducted in-situ FT-IR measurements and found that the M/R-5 aerogel exhibited the best CO2 adsorption capacity under a CO2 flow rate of 10 mL min-1. The density functional theory results demonstrate the correlation between the formation pathway of the product and the charge transfer pathway. This study provides useful ideas for realizing photocatalytic CO2 reduction of macroscopic aerogel materials in gas-solid reaction mode.

Zirconium-Based MOFs and Their Biodegradable Polymer Composites for Controlled and Sustainable Delivery of Herbicides

Adsorption and controlled release of agrochemicals has been studied widely using different nanomaterials and a variety of formulations. However, the potential for application of high surface-area metal–organic frameworks (MOFs) for the controlled release of agrochemicals has not been thoroughly explored. Herein, we report controlled and sustainable release of a widely used herbicide (2-methyl-4-chlorophenoxyacetic acid, MCPA) via incorporation in a range of zirconium-based MOFs and their biodegradable polymer composites. Three Zr-based MOFs, viz., UiO-66, UiO-66-NH₂, and UiO-67 were loaded with MCPA either postsynthetically or in situ during synthesis of the MOFs. The MCPA-loaded MOFs were then incorporated into a biodegradable polycaprolactone (PCL) composite membrane. All three MOFs and their PCL composites were thoroughly characterized using FT-IR, TGA, SEM, PXRD, BET, and mass spectrometry. Release of MCPA from each of these MOFs and their PCL composites was then studied in both distilled water and in ethanol for up to 72 h using HPLC. The best performance for MCPA release was observed for the postsynthetically loaded MOFs, with PS-MCPA@UiO-66-NH₂ showing the highest MCPA concentrations in ethanol and water of 0.056 and 0.037 mg/mL, respectively. Enhanced release of MCPA was observed in distilled water when the MOFs were incorporated in PCL. The concentrations of herbicides in the release studies provide us with a range of inhibitory concentrations that can be utilized depending on the crop, making this class of composite materials a promising new route for future agricultural applications.

Construction of a ZnIn2S4/Au/CdS Tandem Heterojunction for Highly Efficient CO2 Photoreduction

Photocatalytic CO₂ reduction technology is of great importance to alleviate energy crisis and environmental pollution; however, it remains a serious challenge due to the fast recombination of carriers. In this study, we report a three-dimensional structure of a ZnIn₂S₄/Au/CdS composite photocatalyst for the CO₂ reduction reaction, where Au nanoparticles (NPs) are evenly anchored on the surface of ZnIn₂S₄ by photodeposition and Au NPs are wrapped around by CdS. In ZnIn₂S₄/Au/CdS composite photocatalysts, Au NPs act as a bridge to construct a "semiconductor-metal-semiconductor" tandem electron transfer mechanism (ZnIn₂S₄ → Au → CdS) heterojunction, which greatly promotes the transfer of photogenerated electrons. It is worth noting that Au NPs, as a local surface plasmon resonance (LSPR) effect excited source to generate excited-state electrons, further improve the photoreduction CO₂ activity. Under UV-vis light irradiation, the CO yield of ZnIn₂S₄/Au/CdS can reach 63.07 μmol·g^-1·h^-1, which is higher than that of 6.37 μmol·g^-1·h^-1 for pure ZnIn₂S₄, 0.93 μmol·g^-1·h^-1 for CdS, 8.9 μmol·g^-1·h^-1 for ZnIn₂S₄/CdS, 31.04 μmol·g^-1·h^-1 for ZnIn₂S₄/Au, and 5.37 μmol·g^-1·h^-1 for CdS/Au. In addition, the ternary ZnIn₂S₄/Au/CdS composite photocatalyst has good cyclic stability. This study broadens the idea of designing photocatalysts with good carrier separation efficiency.

Strategies for induced defects in metal-organic frameworks for enhancing adsorption and catalytic performance

Metal-organic frameworks (MOFs) have emerged among porous materials. The designable structure and specific functionality make them stand out for diverse applications. In conceptual MOF, the metal ions/clusters and organic ligands...