Tracking of Fluorescently Labeled Polymer Particles Reveals Surface Effects during Shear-Controlled Aggregation

Effect of SiO₂ Nanoparticles on the Performance of PVdF-HFP/Ionic Liquid Separator for Lithium-Ion Batteries

Safety concerns related to the use of potentially explosive, liquid organic electrolytes in commercial high-power lithium-ion batteries are constantly rising. One promising alternative is to use thermally stable ionic liquids (ILs) as conductive media, which are however, limited by low ionic conductivity at room temperature. This can be improved by adding fillers, such as silica or alumina nanoparticles (NPs), in the polymer matrix that hosts the IL. To maximize the effect of such NPs, they have to be uniformly dispersed in the matrix while keeping their size as small as possible. In this work, starting from a water dispersion of silica NPs, we present a novel method to incorporate silica NPs at the nanoscale level (<200 nm) into PVdF-HFP polymer clusters, which are then blended with the IL solution and hot-pressed to form separators suitable for battery applications. The effect of different amounts of silica in the polymer matrix on the ionic conductivity and cyclability of the separator is investigated. A membrane containing 10 wt.% of silica (with respect to the polymer) was shown to maximize the performance of the separator, with a room temperature ionic conductivity of of 1.22 mS cm - 1 . The assembled half-coin cell with LiFePO 4 and Li as the cathode and the anode exhibited a capacity retention of more than 80% at a current density of 2C and 60 ∘ C.

Mechanisms behind overshoots in mean cluster size profiles in aggregation-breakup processes

Aggregation and breakup of small particles in stirred suspensions often shows an overshoot in the time evolution of the mean cluster size: Starting from a suspension of primary particles the mean cluster size first increases before going through a maximum beyond which a slow relaxation sets in. Such behavior was observed in various systems, including polymeric latices, inorganic colloids, asphaltenes, proteins, and, as shown by independent experiments in this work, in the flocculation of microalgae. This work aims at investigating possible mechanism to explain this phenomenon using detailed population balance modeling that incorporates refined rate models for aggregation and breakup of small particles in turbulence. Four mechanisms are considered: (1) restructuring, (2) decay of aggregate strength, (3) deposition of large clusters, and (4) primary particle aggregation where only aggregation events between clusters and primary particles are permitted. We show that all four mechanisms can lead to an overshoot in the mean size profile, while in contrast, aggregation and breakup alone lead to a monotonic, "S"-shaped size evolution profile. In order to distinguish between the different mechanisms simple protocols based on variations of the shear rate during the aggregation-breakup process are proposed.

Core-Shell Morphology of Redispersible Powders in Polymer-Cement Waterproof Mortars

Redispersible powders based on soft core-hard shell polymer particles can be used as additives in polymer-cement mortars. The role of this morphology on the spray-drying production of these powders and on the crack-bridging properties of the corresponding cement-based membranes is investigated. Different polymer latexes at high solid content with varied core-shell ratio, shell thickness and chemical composition (hardness) were prepared from styrene and 2-ethylhexyl acrylate monomers via semi-batch emulsion polymerization. The latexes were characterized in terms of size, composition, and glass transition temperature (T g ), and spray-dried to obtain redispersible polymer powders (RPPs) using poly (vinyl alcohol) and limestone powder as anti-caking agents. The polymer powders were mixed with a mortar mixture and redispersed in water to produce cement-based membranes, which were tested for crack-bridging properties at different temperatures. The results showed that it was not possible to spray-dry a dispersion of homogeneous polymer particles with T g of -25 ∘ C, unless these particles are protected by much harder (high T g ) shell. In particular, it was observed that a thicker shell improved the spray-ability, but lowered the crack-bridging properties of the produced membrane. A trade-off between these two was revealed to be the key for the optimal design of the polymer nanoparticles, as proven by the systematic study of the core-shell morphology reported in this work. The best compromise was shown to consist of particles larger than 300 nm, shell thickness of about 5 nm, and core-shell ratio of 97%, with styrene content in the shell not larger than 80% to avoid excessive hydrophobicity.