Network Formation Kinetics of Poly(dimethylsiloxane) Based on Step-Growth Polymerization

Molecular Weight Distribution of Branched Polymers: Comparison between Monte Carlo Simulation and Flory-Stockmayer Theory

It is challenging to predict the molecular weight distribution (MWD) for a polymer with a branched architecture, though such information will significantly benefit the design and development of branched polymers with desired properties and functions. A Monte Carlo (MC) simulation method based on the Gillespie algorithm is developed to quickly compute the MWD of branched polymers formed through step-growth polymerization, with a branched polyetherimide from two backbone monomers (4,4′-bisphenol A dianhydride and m-phenylenediamine), a chain terminator (phthalic anhydride), and a branching agent (tris[4-(4-aminophenoxy)phenyl] ethane) as an example. This polymerization involves four reactions that can be all reduced to a condensation reaction between an amine group and a carboxylic anhydride group. A comparison between the MC simulation results and the predictions of the Flory-Stockmayer theory on MWD shows that the rates of the reactions are determined by the concentrations of the functional groups on the monomers involved in each reaction. It further shows that the Flory-Stockmayer theory predicts MWD well for systems below the gel point but starts to fail for systems around or above the gel point. However, for all the systems, the MC method can be used to reliably predict MWD no matter if they are below or above the gel point. Even for a macroscopic system, a converging distribution can be quickly obtained through MC simulations on a system of only a few hundred to a few thousand monomers that have the same molar ratios as in the macroscopic system.

High-Loading Poly(ethylene glycol)-Blended Poly(acrylic acid) Membranes for CO2 Separation

Poly(ethylene glycol) (PEG) is an amorphous material of interest owing to its high CO₂ affinity and potential usage in CO₂ separation applications. However, amorphous PEG often has a low molecular weight, making it challenging to form into the membrane. The crystalline high average molar mass poly(ethylene oxide) (PEO) cannot exhibit CO₂ separation characteristics. Thus, it is crucial to employ low molecular weight PEG in high molecular weight polymers to increase the CO₂ affinity for CO₂ separation membranes. In this work, poly(acrylic acid) (PAA)/PEG blend membranes with a PEG-rich phase were simply fabricated by physical mixing with an ethanol solvent. The carbonyl group of the PAA and the hydroxyl group of the PEG formed a hydrogen bond. Furthermore, the thermal stability, glass transition temperature, and surface hydrophilicity of PAA/PEG blend membranes with various PEG concentrations were further characterized. The PAA/PEG(1:9) blend membrane exhibited an improved CO₂ permeability of 51 Barrer with high selectivities relative to the other gas species (H₂, N₂, and CH₄; CO₂/H₂ = 6, CO₂/N₂ = 63, CO₂/CH₄ = 21) at 35 °C and 150 psi owing to the enhanced CO₂ affinity with the amorphous PEG-rich phase. These PAA/PEG blend membrane permeation characteristics indicate a promising prospect for CO₂ capture applications.

Synthesis of Pyridine Heterocyclic Low-Melting-Point Phthalonitrile Monomer and the Effects of Different Curing Agents on Resin Properties

A phthalonitrile monomer (DPTP) containing pyridine with sulfide bonds was prepared and cured into polymers using different curing agents under the same temperature-programmed process. We characterized and comprehensively evaluated the effects of different curing agents on the thermal and thermomechanical properties of phthalonitrile resin, showing that the DPTP monomer cured with naphthalene-containing curing agent exhibited the best performance among the three polymers. Differential scanning calorimetric (DSC) investigation manifested that the melting point of the DPTP monomer was 61 °C, with a processing window of about 170 °C, suggesting the presence of a wide processing range. Thermogravimetric analysis (TGA) demonstrated the outstanding heat resistance, T5%, of 460 °C in nitrogen, at the same time demonstrating superior long-term stability compared with other commonly used polymer materials, which proves the long-term usage under high temperatures of 300 °C. Dynamic mechanical analysis (DMA) revealed that the storage modulus at 50 °C was 3315 MPa, and the glass transition temperature (Tg) of the polymer was more than 350 °C. Therefore, DPTP resins have favorable thermal stability as well as prominent thermomechanical properties.

Capturing Free-Radical Polymerization by Synergetic Ab Initio Calculations and Topological Reactive Molecular Dynamics

Photocurable polymers are used ubiquitously in 3D printing, coatings, adhesives, and composite fillers. In the present work, the free radical polymerization of photocurable compounds is studied using reactive classical molecular dynamics combined with a dynamical approach of the nonequilibrium molecular dynamics (D-NEMD). Different concentrations of radicals and reaction velocities are considered. The mechanical properties of the polymer resulting from 1,6-hexanediol dimethacrylate systems are characterized in terms of viscosity, diffusion constant, and activation energy, whereas the topological ones through the number of cycles (polymer loops) and cyclomatic complexity. Effects like volume shrinkage and delaying of the gel point for increasing monomer concentration are also predicted, as well as the stress-strain curve and Young's modulus. Combining ab initio, reactive molecular dynamics, and the D-NEMD method might lead to a novel and powerful tool to describe photopolymerization processes and to original routes to optimize additive manufacturing methods relying on photosensitive macromolecular systems.

New mechanism for autoxidation of polyolefins: kinetic Monte Carlo modelling of the role of short-chain branches, molecular oxygen and unsaturated moieties

Using quantum-chemical calculations and kinetic modelling, we reveal the dominant reaction pathway in polymer autoxidation, (i) whether oxygen promotes or hamper degradation and (ii) how defects in the polymer backbone affect degradation.

Photo-oxidative cross-linking of thiol polydimethylsiloxane co-polymers via disulfide formation

Disulfide bonds are often employed as reductively cleavable sites in biomaterials and polymers. Here we demonstrate the aerobic photo-cross-linking of thiol-containing polymers through disulfide formation using a sensitizer and telluride catalyst.

Recent advances in polymeric transdermal drug delivery systems

Transdermal delivery has proven to be one of the most favorable methods among novel drug delivery systems. Since drugs administered by transdermal delivery systems avoid the gastrointestinal tract, and thus avoid conversion by the liver, the likelihood of liver dysfunction and gastrointestinal tract irritation as side effects is low. Drug delivery through the skin has other advantages, such as maintaining an effective rate of drug delivery over time, a steady rate of circulation, and the benefits of a passive delivery system and diffusion. Transdermal drug delivery is achieved using patches which consist of different and specific layers. In the last few decades, many types of patches have been approved worldwide, such as medical plasters, which have been generally applied to the skin for localized diseases. Such patches can be traced back to ancient China (around 2000 BCE) and are the early precursors of today's transdermal patches. With the help of effective design, materials, manufacturing, and evaluation, a large number of drugs can now be administered using this valuable advanced technology. This study reviews different types of polymer patches, their advantages and disadvantages, and different studies related to transdermal drug delivery methods, and the advantages and disadvantages of each method. Different mechanisms of transdermal drug delivery system with patches are also discussed.