Asymmetric Superhydrophobic Textiles for Electromagnetic Interference Shielding, Photothermal Conversion, and Solar Water Evaporation

Superhydrophobic Solar-to-Thermal Materials Toward Cutting-Edge Applications

Solar-to-thermal conversion is a direct and effective way to absorb sunlight for heat via the rational design and control of photothermal materials. However, when exposed to water-existed conditions, the conventional solar-to-thermal performance may experience severe degradation owing to the high specific heat capacity of water. To tackle with the challenge, the water-repellent function is introduced to construct superhydrophobic solar-to-thermal materials (SSTMs) for achieving stable heating, and even, for creating new application possibilities under water droplets, sweat, seawater, and ice environments. An in-depth review of cutting-edge research of SSTMs is given, focusing on synergetic functions, typical construction methods, and cutting-edge potentials based on water medium. Moreover, the current challenges and future prospects based on SSTMs are also carefully discussed.

Ag Nanoparticles-Coated Shish-Kebab Superstructure Film for Wearable Heater

Passive and active wearable heaters have received widespread attention due to their efficient utilization of solar energy and all-weather heating capabilities, but the current challenges are their preparation processes being time-consuming and equipment expensive. Herein, a simple and facilitated preparation method for the multifunctional wearable heater was developed, which springs Ag nanoparticles on the shish-kebab superstructure film via deposited melanin-like polydopamine as the adhesive. The light absorption ability of the resultant wearable heater in the visible region can be significantly enhanced by the addition of polydopamine, realizing a highly efficient photothermal conversion ability. Accordingly, it can achieve rapid warming ability whether passive heating (up to 45 °C about 60 s at 100 mW/cm2) or active heating (up to 72 °C about 40 s at 0.6 V), compared to ordinary cotton fabric. In addition, it can realize a 6.3 °C temperature difference with Cotton, showing excellent heat preservation ability. This study demonstrates a simple and low-cost approach for the prepared shish-kebab superstructure-based wearable heaters.

Cellulose-based evaporator with dual boost of water transportation and photothermal conversion for highly solar-driven evaporation

Two-dimensional (2D) evaporation systems could significantly reduce the heat conduction loss compared with the photothermal conversion materials particles during the evaporation process. But the normal layer-by-layer self-assembly method of 2D evaporator would reduce the water transportation performance due to the highly compact channel structures. Herein, in our work, the 2D evaporator with cellulose nanofiber (CNF), Ti₃C₂T_x (MXene) and polydopamine modified lignin (PL) by layer-by-layer self-assembly and freeze-drying methods. The addition of PL also enhanced the light absorption and photothermal conversion performance of the evaporator due to the strong conjugation and π-π molecular interactions. After the combination process of layer-by-layer self-assembly and freeze-drying process, the as-prepared freeze-dried CNF/MXene/PL (f-CMPL) aerogel film exhibited highly interconnected porous structure with promoted hydrophilicity (enhanced water transportation performance). Benefiting these favorable properties, the f-CMPL aerogel film showed enhanced light absorption performance (surface temperature could be reached to 39 °C under 1 sun irradiation) and higher evaporation rate (1.60 kg m^-2 h^-1). This work opens new way to fabricate cellulose-based evaporator with highly evaporation performance for the solar steam generation and provides a new idea for improving the evaporation performance of 2D cellulose-based evaporator.

Integrating Fly Ash-Controlled Surface Morphology and Candle Grease Coating: Access to Highly Hydrophobic Poly (L-lactic Acid) Composite for Anti-Icing Application

New ways of recycling fly ash are of great significance for reducing the environmental pollution. In this work, biodegradable hydrophobic poly (L-lactic acid)/fly ash composites for anti-icing application were successfully fabricated via a facile solvent-volatilization-induced phase separation approach. A silane coupling agent of 3-(Trimethoxysilyl) propyl methacrylate was used to decorate a fly ash surface (FA@KH570) for strengthening the interface bonding between fly ash and poly (L-lactic acid). Moreover, FA@KH570 could obviously enhance the crystallinity of poly (L-lactic acid) (PLLA)/FA@KH570 composites, which accelerated the conversion from the liquid-liquid to the liquid-solid phase separation principle. Correspondingly, the controllable surface morphology from smooth to petal-like microspheres was attained simply by adjusting the FA@KH570 content. After coating nontoxic candle grease, the apparent contact angle of 5 wt% PLLA/FA@KH570 composite was significantly increased to an astonishing 151.2°, which endowed the composite with excellent anti-icing property. This strategy paves the way for recycling waste fly ash and manufacturing hydrophobic poly (L-lactic acid) composite for potential application as an anti-icing material for refrigerator interior walls.

Fractal Growth of Quasi Two-Dimensional Copper Dendrites by Template-free Electrodeposition

Fractal dendrites are extensively observed in industry, especially in the electrochemical deposition process. The fractal dendrite electrodeposition behavior of quasi-two-dimensional Cu (Q2D-Cu) metal based on the wire is examined via direct electrodeposition using a thin layer reactor. Here, to explain the fractal growth mechanism, the directional migration and random walking of ions are introduced in the traditional diffusion-limited aggregation model, and fractal patterns consistent with the experimental results are successfully simulated. In addition, the Cu fractal dendrite structure is finely adjusted by varying electrodeposition conditions, demonstrating its great potential for further optimization. The CuO/Q2D-Cu fractal dendrite photothermal device fabricated through in situ assembly of CuO nanowires on Cu fractal dendrite has good photothermal conversion ability. Therefore, metal fractal dendrites, which are considered harmful in the electroplating industry, have application prospects in the photothermal field.

Versatile Melanin-Like Coatings with Hierarchical Structure toward Personal Thermal Management, Anti-Icing/Deicing, and UV Protection

Superhydrophobic photothermal coatings are promising for multifunctional applications due to the efficient use of solar energy, but the current challenge is to seek one easy-to-prepare material with high photothermal performance. Herein, inspired by mussel adhesion and lotus leaf surfaces, we developed superhydrophobic photothermal coatings with hierarchical structure by depositing melanin-like polydopamine (PDA) and dip-coating polydimethylsiloxane (PDMS)/hydrophobic fumed silica (SiO₂) sequentially. Benefitting from the efficient photothermal conversion performance of PDA, the coated fabric can rapidly warm up to 100 °C under 100 mW/cm² sun irradiation. Meanwhile, the coatings show excellent superhydrophobic properties (WCA of 163°), which not only prevent the adhesion of the contaminant from maintaining a long-term and efficient photothermal performance but also help the fabric to own outstanding passive anti-icing and active deicing performances. Furthermore, the superhydrophobic properties of the coatings can be maintained after sandpaper abrasion, repeat tape-peeling, and ultrasonication. In addition, superior UV protection of the coatings can meet the long-term service conditions under outdoor sunlight. The PDA-based superhydrophobic photothermal coatings are believed to inspire new strategies for solar-driven multifunctional applications such as personal thermal management, anti-icing/deicing of variously shaped components, photothermal antibacterial, and so on.

Flexible biomimetic materials with excellent photothermal performance and superhydrophobicity

Although thousands of superhydrophobic composites have been reported, it is still a challenge to develop eco-friendly superhydrophobic materials by a simple and low-cost strategy. Here, a paper-based superhydrophobic material was prepared by carbon fiber powders and polydimethylsiloxane through a facile spraying method. This obtained material has excellent liquid resistance and self-cleaning properties, whose contact angle reaches 155°. In addition, it possesses excellent photothermal conversion characteristics with a stable surface temperature of 73.4 °C and good water evaporation performance with an evaporation rate up to 1.08 kg/(m2·h) under one solar intensity (100 mW/cm2). Also, it has outstanding self-deicing performance, whose deicing time is 120 s earlier than that of the untreated surface under one solar intensity. An adaptability test shows this strategy of functional coatings can also be applied to other fiber substrates (coating paper, kraft paper, non-woven fabric, paulownia veneer, etc.). Overall, this superhydrophobic material has a promising application prospect in many fields such as waterproof packaging, deicing materials, water evaporation materials, etc.

Superhydrophobic MXene Coating with Biomimetic Structure for Self-Healing Photothermal Deicing and Photoelectric Detector

Two-dimensional transition metal carbides (Ti₃C₂T_x MXene) have emerged as new candidates for applications in multifunctional devices owing to their outstanding performance. However, these electronic devices are easily disturbed by water, breakage, oxidation during use, and limited energy resources. To solve these problems, herein, inspired by nature, a novel superhydrophobic, healable photothermal deicing and photodetector (SHPP) with a "papillary structure" is successfully fabricated for the first time, by a simple layer-by-layer assembly spraying process with 0D/1D/2D nanomaterials. As a result, the superhydrophobic modified 2D MXene coating (FM coating) on the SHPP sensor exhibits outstanding self-cleaning, long-term durability (>20 days), as well as excellent photothermal deicing performances under near-infrared light. Meanwhile, the unique semiembedded nano-ZnO/1D silver nanowire supports the sensor with desirable photoelectric performance with UV light and a fast response time (∼1 s), and good cycle stability. Moreover, benefiting from the transparent self-healing substrate, the photothermal deicing and photodetector properties can be restored at room temperature. The bioinspired structures and function mechanisms offer SHPP sensors great potential for the utilization of clean light energy, sensing, self-cleaning, anti-icing, and so forth.

Simple Design of a Porous Solar Evaporator for Salt-Free Desalination and Rapid Evaporation

Solar-driven interfacial evaporation is considered to be one of the promising and efficient ways of producing clean water in recent years. However, it remains a challenge to develop solar evaporation devices with high solar evaporation rates and salt-free blocking properties. Here, a porous solar evaporator with directed water transport and salt-free desalination through excellent photothermal conversion and purposefully guided migration of the salt solution was developed. The designed porous photothermal sponge with the synergistic effect of MXene and polypyrrole can achieve evaporation rates of 1.47 and 2.27 kg m^-2 h^-1, respectively, in the capillary model and siphon model water-transporting solar evaporation devices. More interestingly, the designed zigzag-shaped device with an evaporation rate of 2.45 kg m^-2 h^-1 was achieved. In addition, the evaporator can operate stably under 9 h in the siphon model solar evaporation device and achieves the effect of salt-free desalination. The above design provides a good strategy for solar-powered desalination applications.

Wettability Controlled Surface for Energy Conversion

To achieve clean and high-efficiency utilization of renewable energy, functional surfaces with controllable and patternable wettability are becoming a fast-growing research focus. In this work, a laser scribing strategy to fabricate patterned graphene surfaces that are capable of energy conversion in different forms is demonstrated. Using the laser raster-scanning and vector-scanning modes, two distinct surface structures are constructed on polybenzoxazine substrate, yielding a superhydrophilic (LSHL) surface and superhydrophobic (LSHB) surface, respectively. Of particular note is that the unique hierarchical structure of LSHB surface has endowed it with quite a robust superwetting behaviors. Further profiting from the flexibility of the processing method, wettability patterns with spatially resolved LSHL and LSHB regions are designed, achieving the conversion of surface energy to liquid kinetic energy. This also offers a tractable approach to fabricate wettability-engineered devices that enable the directional, pumpless transport of water by capillary pressure gradient and the selective surface cooling via jet impingement. In addition, the LSHB surface demonstrates the high conversion of electric-to-thermal energy (222 °C cm² W^-1 ) and light-to-thermal energy (88%). Overall, the material system and processing method present a promising step forward to developing easy-fabricated graphene surfaces with spatially controlled wettability for efficient energy utilization and conversion.

Superhydrophobic E-textile with an Ag-EGaIn Conductive Layer for Motion Detection and Electromagnetic Interference Shielding

As as emerging innovation, electronic textiles have shown promising potential in health monitoring, energy harvesting, temperature regulation, and human-computer interactions. To access broader application scenarios, numerous e-textiles have been designed with a superhydrophobic surface to steer clear of interference from humidity or chemical decay. Nevertheless, even the cutting-edge electronic textiles (e-textiles) still have difficulty in realizing superior conductivity and satisfactory water repellency simultaneously. Herein, a facile and efficient approach to integrate a hierarchical elastic e-textile is proposed by electroless silver plating on GaIn alloy liquid metal coated textiles. The continuous uneven surface of AgNPs and deposition of FAS-17 endow the textile with exceptional and robust superhydrophobic performance, in which the conductivity and the contact angle of the as-made textile could reach 2145 ± 122 S/cm and 161.5 ± 2.1°, respectively. On the basis of such excellent conductivity, the electromagnetic interference (EMI) shielding function is excavated and the average shielding efficiency (SE) reaches about 87.56 dB within frequencies of 8.2-12.4 GHz. Furthermore, due to its high elasticity and low modulus, the textile can serve as a wearable strain sensor for motion detection, health monitoring, and underwater message transmission. This work provides a novel route to fabricate high-performance hydrophobic e-textiles, in which the encapsulation strategy could be referenced for the further development of conductive textiles.

Multi-interface Assembled N-Doped MXene/HCFG/AgNW Films for Wearable Electromagnetic Shielding Devices with Multimodal Energy Conversion and Healthcare Monitoring Performances

With the progressive requirements of modern electronics, outstanding electromagnetic interference (EMI) shielding materials are extensively desirable to protect intelligent electronic equipment against EMI radiation under various conditions, while integrating functional applications. So far, it remains a great challenge to effectively construct thin films with diversiform frameworks as integrated shielding devices. To simultaneously promote electromagnetic waves (EMWs) attenuation and construct integrated multifunction, an alternating-layered deposition strategy is designed to fabricate polydimethylsiloxane packaged N-doped MXene (Ti₃CNT_x)/graphene oxide wrapped hollow carbon fiber/silver nanowire films (p-LMHA) followed by annealing and encapsulation approaches. Contributed by the synergistic effect of consecutively conductive networks and porous architectures, LMHA films exhibit satisfying EMI shielding effectiveness of 73.2 dB at a thickness of 11 μm, with a specific EMI shielding effectiveness of 31 150.1 dB·cm²·g^-1. Benefiting from the encapsulation, p-LMHA films further impart hydrophobicity and reliability against harsh environments. Besides, p-LMHA devices integrate a rapid-response behavior of the electro/photothermal and, meanwhile, function as a healthcare monitoring sensor. Therefore, it is believed that the p-LMHA films assembled by independent conductive networks with reliability offer a facile solution for practical multimodular protection of devices with integration characteristics.

Layer-by-Layer Assembly of Ag@Ti3C2TX and Chitosan on PLLA Substrate to Enhance Antibacterial and Biocompatibility

Poly L-lactic acid (PLLA) is a non-toxic, biocompatible degradable polymer material with excellent mechanical properties after molding. However, it faces challenges in the use of biomedical materials because of its intolerance to bacteria. Here, we use an easy-to-operate method to prepare a composite multilayer membrane: PLLA membrane was used as substrates to assemble positively charged chitosan and negatively charged Ag@MXene on the surface using the Layer-by-layer (LBL) method. The assembly process was detected by Fluorescein Isothiocyanate (FITC)-labelled chitosan and the thickness of the coating multilayer was also detected as 210.0 ± 12.1 nm for P-M membrane and 460.5 ± 26.5 nm for P-Ag@M membrane. The surface self-assembled multilayers exhibited 91.27% and 96.11% growth inhibition ratio against E. coli and S. aureus strains under 808 nm near-infrared (NIR) laser radiation with a synergistic photothermal antibacterial effect. Furthermore, best biocompatibility of P-M and P-Ag@M membranes compare to PLLA membrane motivated us to further explore its application in biomedical materials.

Functional Polyaniline/MXene/Cotton Fabrics with Acid/Alkali-Responsive and Tunable Electromagnetic Interference Shielding Performances

Although two-dimensional transition-metal carbides (MXenes) and intrinsic conductive polymers have been combined to produce functional electromagnetic interference (EMI) shielding composites, acid/alkali-responsive EMI shielding textiles have not been reported. Herein, electrically conductive polyaniline (PANI)/MXene/cotton fabrics (PMCFs) are fabricated by an efficient vacuum filtration-assisted spray-coating method for acid/alkali-responsive and tunable EMI shielding applications on the basis of the high electrical conductivity of MXene sheets and the acid/alkali doping/de-doping feature of PANI nanowires. The as-prepared PMCF exhibits a sensitive ammonia response of 19.6% at an ammonia concentration of 200 ppm. The high EMI shielding efficiency of ∼54 dB is achieved by optimizing the decorated structure of the PANI/MXene coating on the cotton fabrics. More importantly, the PMCF can act adaptively as a "switch" for EMI shielding between the efficient strong shielding of 24 dB and the inefficient weak shielding of 15 dB driven by the stimulation of hydrogen chloride and ammonia vapors. This multifunctional fabric would possess promising applications for intelligent garments, flexible electronic sensors, and smart electromagnetic wave response in special environments.

A Simple Polypyrrole/Polyvinylidene Fluoride Membrane with Hydrophobic and Self-Floating Ability for Solar Water Evaporation

The traditional hydrophobic solarevaporator is generally obtained through the modification of alkyl or fluoroalkyl on the photothermal membrane. However, the modified groups can easily be oxidized in the long-term use process, resulting in the poor salt resistance and stability of photothermal membrane. In order to solve this problem, a simple polypyrrole/polyvinylidene fluoride membrane, consisting of an intrinsic hydrophobic support (polyvinylidene fluoride) and a photothermal material (polypyrrole), was fabricated by ultrasonically mixing and immersed precipitation. This photothermal membrane showed good self-floating ability in the process of water evaporation. In order to further improve the photothermal conversion efficiency, a micropyramid structure with antireflective ability was formed on the surface of membrane by template method. The micropyramids can enhance the absorption efficiency of incident light. The water evaporation rate reached 1.42 kg m⁻² h⁻¹ under 1 sun irradiation, and the photothermal conversion efficiency was 88.7%. The hydrophobic polyvinylidene fluoride ensures that NaCl cannot enter into membrane during the evaporation process of the brine, thus realizing the stability and salt resistance of polypyrrole/polyvinylidene fluoride in 3.5%wt and 10%wt NaCl solution.

Flexible Ti3C2T x /(Aramid Nanofiber/PVA) Composite Films for Superior Electromagnetic Interference Shielding

Multifunctional electromagnetic interference (EMI) shielding materials would solve electromagnetic radiation and pollution problems from electronic devices. Herein, the directional freeze-drying technology is utilized to prepare the aramid nanofiber/polyvinyl alcohol aerogel with a directionally porous structure (D-ANF/PVA), and the Ti₃C₂T_x dispersion is fully immersed into the D-ANF/PVA aerogel via ultrasonication and vacuum-assisted impregnation. Ti₃C₂T_x/(ANF/PVA) EMI shielding composite films with directionally ordered structure (D-Ti₃C₂T_x/(ANF/PVA)) are then prepared by freeze-drying and hot pressing. Constructing a directionally porous structure enables the highly conductive Ti₃C₂T_x nanosheets to be wrapped on the directionally porous D-ANF/PVA framework in order arrangement and overlapped with each other. And the hot pressing process effectively reduces the layer spacing between the stacked wavy D-ANF/PVA, to form a large number of Ti₃C₂T_x-Ti₃C₂T_x continuous conductive paths, which significantly improves the conductivity of the D-Ti₃C₂T_x/(ANF/PVA) EMI shielding composite film. When the amount of Ti₃C₂T_x is 80 wt%, the EMI shielding effectiveness (EMI SE) and specific SE (SSE/t) of D-Ti₃C₂T_x/(ANF/PVA) EMI shielding composite film achieve 70 dB and 13790 dB·cm²·g⁻¹ (thickness and density of 120 μm and 0.423 g·cm⁻³), far superior to random-structured Ti₃C₂T_x/(ANF/PVA) (R-Ti₃C₂T_x/(ANF/PVA)) composite film (46 dB and 9062 dB·cm²·g⁻¹, respectively) via blending-freeze-drying followed by hot pressing technology. Meanwhile, the D-Ti₃C₂T_x/(ANF/PVA) EMI shielding composite film possesses excellent flexibility and foldability.

Bimodal Tactile Sensor without Signal Fusion for User-Interactive Applications

Tactile sensors with multimode sensing ability are cornerstones of artificial skin for applications in humanoid robotics and smart prosthetics. However, the intuitive and interference-free reading of multiple tactile signals without involving complex algorithms and calculations remains a challenge. Herein a pressure-temperature bimodal tactile sensor without any interference is demonstrated by combining the fundamentally different sensing mechanisms of optics and electronics, enabling the simultaneous and independent sensing of pressure and temperature with the elimination of signal separation algorithms and calculations. The bimodal sensor comprises a mechanoluminescent hybrid of ZnS-CaZnOS and a poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) thermoresistant material, endowing the unambiguous transduction of pressure and temperature into optical and electrical signals, respectively. This device exhibits the highest temperature sensitivity of -0.6% °C^-1 in the range of 21-60 °C and visual sensing of the applied forces at a low limitation of 2 N. The interference-free and light-emitting characteristics of this device permit user-interactive applications in robotics for encrypted communication as well as temperature and pressure monitoring, along with wireless signal transmission. This work provides an unexplored solution to signal interference of multimodal tactile sensors, which can be extended to other multifunctional sensing devices.

Multifunctional cotton with PANI-Ag NPs heterojunction for solar-driven water evaporation

Water evaporation using photothermal materials is a cost-effective and sustainable technology for alleviating the world's freshwater crisis, but oil contaminants and organic pollutants exist in the original water sources, which severely degrade the evaporation performance and pose environmental hazards. In this paper, we demonstrate a photothermal material (multifunctional cotton) that simultaneously demonstrates oil-resistance, organic pollutant removal, and a high water evaporation rate. A Schottky heterostructure was formed between polyaniline (PANI) and Ag NPs, which improved the photothermal conversion and achieved a water evaporation rate of 1.37 kg m^-2 h^-1 and photothermal conversion efficiency of 84.7% under one-sun illumination (1 kW m^-2). Notably, various organic pollutants in the water source were thoroughly removed by visible-light catalytic degradation and adsorption, which displayed efficiencies of 99.3% and 97%, respectively. The multifunctional cotton also possessed excellent superoleophobicity, and repelled oil contaminants and organic pollutants in water. Considering these merits, the as-prepared multifunctional cotton is an outstanding candidate for water evaporation from various sources.

Preparation and Self-Cleaning Performance of Carbon-Based Superhydrophobic Coatings Based on Non-Fluorine and Non-Toxic Corn Straw

Recently, superhydrophobic surfaces with self-cleaning ability have attracted broad research interest due to their huge potential in daily lives and industrial applications, but the use of fluorinate, toxic organic compounds, and expensive feedstocks make superhydrophobic materials a great challenge in practical application. In this study, we present a facile dip-coating strategy to prepare superhydrophobic coatings with self-cleaning properties based on a non-fluorine and non-toxic system by using eco-friendly corn straw as raw material. During this process, aromatic carbon particles with rough hierarchical structures were prepared firstly via a simple fast pyrolysis process, followed by modification with polydimethylsiloxane (PDMS) in absolute ethanol solvent to decrease the surface free energy. Research shows these natural straw-derived carbons display a microstructure of several protrusions which is similar to the lotus leave’s and the resulted coatings exhibit an outstanding superhydrophobic property with a static water contact angle (WCA) of 151.67 ± 1.36 degrees. In addition, the as-prepared coatings possessed excellent self-cleaning performance: no contaminations were observed on the surfaces after examining with sludge, calcimine, water, and common liquids such as tea, milk, soybean milk as well as ink, which have a broad range of potential application in the field of antifouling, waterproofing, and anticorrosive.

Flexible Ag Microparticle/MXene-Based Film for Energy Harvesting

Ultra-thin flexible films have attracted wide attention because of their excellent ductility and potential versatility. In particular, the energy-harvesting films (EHFs) have become a research hotspot because of the indispensability of power source in various devices. However, the design and fabrication of such films that can capture or transform different types of energy from environments for multiple usages remains a challenge. Herein, the multifunctional flexible EHFs with effective electro-/photo-thermal abilities are proposed by successive spraying Ag microparticles and MXene suspension between on waterborne polyurethane films, supplemented by a hot-pressing. The optimal coherent film exhibits a high electrical conductivity (1.17×10⁴ S m^-1), excellent Joule heating performance (121.3 °C) at 2 V, and outstanding photo-thermal performance (66.2 °C within 70 s under 100 mW cm^-1). In addition, the EHFs-based single-electrode triboelectric nanogenerators (TENG) give short-circuit transferred charge of 38.9 nC, open circuit voltage of 114.7 V, and short circuit current of 0.82 μA. More interestingly, the output voltage of TENG can be further increased via constructing the double triboelectrification layers. The comprehensive ability for harvesting various energies of the EHFs promises their potential to satisfy the corresponding requirements.