Thiol-Yne Click Postsynthesis of a Sulfonate Group-Enriched Magnetic Microporous Organic Network for Efficient Extraction of Benzimidazole Fungicides

Effective extraction of trace cytokinins in plants based on a carboxyl functionalized microporous organic network

Cytokinin (CK) is a type of hormone that exists widely in plants and plays a significant role in promoting cell proliferation and division. Developing a rapid and sensitive method for the detection of trace CKs remains challenging. Microporous organic networks (MONs) are novel materials widely used in sample preparation owing to their excellent extraction performance. Therefore, a dispersive solid phase extraction method based on carboxylated microporous organic networks (MON-2COOH), combined with ultra-high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) for the detection of four CKs was developed. Upon introducing a carboxyl group into pure MON, the MON-2COOH material had excellent stability, high porosity, and a good dispersion effect, and provided more interaction sites to achieve good adsorption of target compounds. Under the best conditions, the established dSPE-UPLC-MS/MS method had the advantages of low adsorbent dosage (2 mg), low detection limit (1.0-10.0 pg mL-1) and good reproducibility (RSD ≤ 6.54%, n = 5). Synergistic extraction mechanisms involving π-π, hydrogen bonding and hydrophobic interactions were elucidated using both density functional theory calculations and experimental data. This work also confirmed the feasibility of functionalized MONs as satisfactory adsorbents for the enrichment of small organic compounds.

Synthesis of a fluorophilic magnetic microporous organic network for selective enrichment of fipronil and ethiprole in milk and egg samples

Considering the widespreadly use, large consumption, and serious environmental and health threats of phenylpyrazole insecticides (PPIs), development of a selective and sensitive method for accurate detection of their residuals in food samples is of great significance and challenging. Herein, depending on the hydrophobic and F-containing characteristics of PPIs, a novel fluorinated magnetic microporous organic network (FMMON) was designed and prepared for efficient and selective magnetic solid-phase extraction (MSPE) of two typical PPIs (fipronil and ethiprole) from milk and egg samples before the HPLC-UV determination. FMMON owned large specific surface area, multiple interaction sites, excellent magnetic separation performance and stability and exhibited good extraction and selectivity for fipronil and ethiprole through the specific F-F, hydrogen bonding, hydrophobic, and π-π interactions. Under optimal extraction conditions, the established FMMON-MSPE-HPLC-UV method provided wide linear ranges (0.1-1000 µg L-1), low limits of detection (0.03-0.05 µg L-1), large enrichment factors (96.2-99.7), low adsorbent consumption (4 mg), and short extraction time (6 min) for fipronil and ethiprole. This work revealed the bright future of fluorinated MONs in sample pretreatment of fluorinated contaminants in complex substrates.

Efficient construction of high-quality sulfonated porous aromatic frameworks by optimizing the swelling state of porous structures

Conventional post-modification methods usually face the fundamental challenge of balancing the high content of functional groups and large surface area for porous organic polymers (POPs). The reason, presumably, stems from ineffective and insufficient swelling of the porous structure of POP materials, which is detrimental to mass transfer and modification of functional groups, especially with large-sized ones. It is important to note that significant differences exist in the porous structures of POP materials in a solvent-free state after thermal activation and solvent swelling state. Herein, we propose that the improvement of the swelling state of the porous structure of POP materials is more conducive to obtaining high-quality sulfonated POP materials, and employ a one-pot modification strategy for preparing sulfonated porous aromatic frameworks (PAFs) to prove the proposal. These results show that the specific surface area of the resulting polymer is 580 m2 g-1 with a sulfur content of up to 13.2 wt%, which is superior to most sulfonated porous materials and the control sample. More importantly, we have also shown that the same conclusion is reached by performing similar treatments on hyper-crosslinked polymers (HCPs) and conjugated microporous polymers (CMPs), proving that our hypothesis is effective and feasible when compared to the conventional post-sulfonation method. The excellent hydrophilicity, rich content of sulfonic acid groups, high specific surface area and hierarchical pore structure make the resulting polymer an ideal adsorbent for micro-pollutants in water. The maximum adsorption capacities for Rhodamine B (RhB), Methylene Blue (MB), Tetracycline (TC) and Ciprofloxacin (CIP) are 1075 mg g-1, 1020 mg g-1, 826 mg g-1 and 1134 mg g-1, respectively. This study not only demonstrates the preparation of efficient sulfonated porous adsorbents for the efficient removal of cationic dyes and antibiotics but also illustrates an effective method for constructing high-quality functional POP materials by optimizing the swelling state of the porous structure.

Fabrication of fluorinated magnetic microporous organic network for selective and efficient extraction of benzoylurea insecticides in tea beverages

In this work, a novel fluorinated magnetic microporous organic network (Fe3O4@FMON) was exquisitely designed and synthesized for highly efficient and selective magnetic solid phase extraction (MSPE) of fluorinated benzoylurea insecticides (BUs) from complex tea beverage samples. The Fe3O4@FMON exhibited good extraction for BUs via the pre-designed hydrophobic, π-π stacking, hydrogen bonding and specific FF interactions. A sensitive Fe3O4@FMON-based MSPE-HPLC-UV method with wide linear range (0.10-1000 μg L-1, R2 ≥ 0.996), low limits of detection (0.01-0.02 μg L-1), and large enrichment factors (85.6-98.0) for BUs from tea beverage samples was developed. By decorating F elements within MON's networks, the Fe3O4@FMON characterized good hydrophobicity and chemical stability, which could be reused at least 8 times without decrease of recoveries. This work demonstrated the great prospects of Fe3O4@FMON for enriching trace BUs from complex substrates and triggered the potential of FMON for sample pretreatment of fluorinated analytes.

Hydroxyl-functionalized cationic porous organic polymers for efficient enrichment and detection of phenolic endocrine disrupting chemicals in water and snapper

Endocrine-disrupting chemicals (EDCs) can disrupt the normal functioning of the endocrine system in organisms, leading to various health issues. Therefore, monitoring EDCs in the environment and food is of significant importance. In this study, a hydroxyl-functionalized ionic porous organic polymer (OH-IPOP) has been synthesized for the first time using 2-benzimidazolemethanol as a monomer. The OH-IPOP exhibited excellent adsorption performance towards phenolic EDCs. An efficient method for determination of phenolic EDCs (p-tert-butylphenol, bisphenol B, bisphenol A and bisphenol F) in environmental water and snapper samples was successfully established by with OH-IPOP as solid-phase extraction sorbent and determination with high-performance liquid chromatography-ultraviolet detection. The method showed good linearity (r2 > 0.998), low detection limits (0.008-0.020 ng mL-1 for lake water, 1.00-3.00 ng/g for snapper), high recovery rates (82.3-106 %), and good precision (relative standard deviation < 6.6 %), making it a highly efficient adsorbent for the enrichment of EDCs in complex sample matrices.

Preparation of alkyl microporous organic network-based capillary column for an efficient gas chromatographic separation of position isomers

The large surface area, excellent thermal stability and easy modification make microporous organic networks (MONs) good candidates in the field of gas chromatography (GC). Due to the limited species and highly conjugated networks of MONs, their applications are still in infancy and restricted. To accelerate their developments and to enrich their types in GC, here we report the first example of synthesizing alkyl MON and its capillary column for GC separation of position isomers. Linear 1,8-dibromooctane is used as the alkyl monomer instead of traditional aromatic ones to construct novel alkyl MON to decrease the inherent conjugated characteristic of MONs. The alkyl MON exhibits good thermal stability (up to 350°C), large surface area (1173 m2 g-1), and non-polar character, allowing good resolution for alkanes, alkyl benzenes, alcohols, ketones, and diverse position isomers, including dichlorobenzene, trichlorobenzene, bromotoluene, nitrotoluene, methylbenzaldehyde, and ionone with the limits of detection (0.003 mg mL-1) and limits of quantitation of (0.10 mg mL-1). The in situ growth-prepared alkyl MON column demonstrates remarkable duration time and precisions for the retention relative standard deviations, (RSDs%, intra-day, n = 7), 0.06%-0.53% (intra-day, n = 7), and 2.87%-10.59% (column-to-column, n = 3). In addition, the fabricated alkyl MON-coated capillary column offers better resolution than three commercial GC columns for the resolution of methylbenzaldehyde, bromotoluene, and chlorotoluene isomers. This work reveals the practicability for synthesizing alkyl MONs and demonstrates their prospects for position isomers separation.

Novel phenazine-based microporous organic network for selective and sensitive determination of trace sulfonamides in milk samples

BACKGROUND

Sulfonamide (SA) residues in food of animal origin possess a potential threat to human health and environment. However, due to the polar and ionic characteristics and trace level of SAs and the complexity of food matrices, direct measurement of SAs in these samples is still very difficult. Development of efficient sample pretreatment method for sensitive and selective extraction of trace SAs is of great significance and urgently desired. Therefore, rational design and synthesizing advanced and selective extractants is quite important.

RESULTS

In this work, a novel phenazine-based microporous organic network (MON) named TEPM-DP is reasonably synthesized and employed as a packing material for selective solid phase extraction (SPE) and sensitive determination of four typical SAs in milk samples. Phenazine-based monomer with aromatic and heteroaromatic ring and numerous N atoms is chosen to construct TEPM-DP adsorbent to provide π-π, hydrogen bonding, hydrophobic, and electrostatic extraction sites for SAs. The proposed method owns wide linear ranges, low limits of detection, high enrichment factors, and good precisions and recoveries for SAs in complex milk samples. The recoveries of SAs on TEPM-DP are much higher than those of commercial C18 and activated carbon. The extraction mechanisms are also elucidated via FT-IR, XPS, and comparative experiments.

SIGNIFICANCE

This work reports the first example of design and synthesizing phenazine-based MON in SPE via a simple and rapid solvothermal method. The results reveal the great prospects of TEPM-DP for enriching polar and ionic SAs in complex samples and uncover the potency of phenazine-based MON in sample pretreatment, which will promote the development of MON.

Thiol-yne click post-synthesis of phenylboronic acid-functionalized magnetic cyclodextrin microporous organic network for selective and efficient extraction of antiepileptic drugs

Owing to their incomplete digestion in the human body and inadequate removal by sewage treatment plants, antiepileptic drugs (AEDs) accumulate in water bodies, potentially affecting the exposed humans and aquatic organisms. Therefore, sensitive and reliable detection methods must be urgently developed for monitoring trace AEDs in environmental water samples. Herein, a novel phenylboronic acid-functionalized magnetic cyclodextrin microporous organic network (Fe3O4@CD-MON-PBA) was designed and synthesized via the thiol-yne click post-modification strategy for selective and efficient magnetic solid-phase extraction (MSPE) of trace AEDs from complex sample matrices through the specific B-N coordination, π-π, hydrogen bonding, electrostatic, and host-guest interactions. Fe3O4@CD-MON-PBA exhibited a large surface area (118.5 m2 g-1), rapid magnetic responsiveness (38.6 emu g-1, 15 s), good stability and reusability (at least 8 times), and abundant binding sites for AEDs. Under optimal extraction conditions, the proposed Fe3O4@CD-MON-PBA-MSPE-HPLC-UV method exhibited a wide linear range (0.5-1000 μg L-1), low limits of detection (0.1-0.5 μg L-1) and quantitation (0.3-2 μg L-1), good anti-interference ability, and large enrichment factors (92.2-104.3 to 92.3-98.0) for four typical AEDs. This work confirmed the feasibility of the thiol-yne click post-synthesis strategy for constructing novel and efficient multifunctional magnetic CD-MONs for sample pretreatment and elucidated the significance of B-N coordination between PBA and N-containing AEDs.

Facile preparation of covalent-organic framework composites for magnetic solid-phase extraction of naphthaleneacetic acid in food prior to HPLC-UV analysis

Novel magnetic covalent organic frameworks (COFs) were prepared by one-pot synthetic strategy and employed as an efficient adsorbent for magnetic solid-phase extraction (MSPE) of naphthaleneacetic acid (NAA) in food samples. Depending on the predesigned the hydrogen bonding, π-π and hydrophobic interactions of magnetic COFs, the efficient and selective extraction process for NAA was achieved within 15 min. The magnetic COFs adsorbent combined with HPLC-UV was devoted to develop a novel quantitative method for NAA in complex food. The method afforded good coefficient in range of 0.002-10.0 µg mL-1 and low limit of detection was 0.0006 µg mL-1. And the newly established method afforded less adsorbent consumption, wider linearity and lower LODs than the reported analytical methods. Ultimately, the method was successfully applied to determine NAA in fresh pear, tomato and peach juice. The magnetic COFs based MSPE coupled with HPLC-UV method provided a simple, efficient and dependable alternative to monitor trace NAA in food samples.

Fabrication of sea urchin shaped polyaniline-modified magnetic microporous organic network for efficient extraction of non-steroidal anti-inflammatory drugs from animal-derived food samples

In this work, a novel polyaniline-modified magnetic microporous organic network (MMON-PANI) composite was fabricated for effective magnetic solid phase extraction (MSPE) of five typical nonsteroidal anti-inflammatory drugs (NSAIDs) from animal-derived food samples before high performance liquid chromatography (HPLC) detection. The core-shell sea urchin shaped MMON-PANI integrates the merits of Fe3O4, MON, and PANI, exhibiting large specific surface area, rapid magnetic responsiveness, good stability, and multiple binding sites to NSAIDs. Convenient and effective extraction of trace NSAIDs from chicken, beef and pork samples is realized on MMON-PANI via the synergetic π-π, hydrogen bonding, hydrophobic, and electrostatic interactions. Under optimal conditions, the MMON-PANI-MSPE-HPLC-UV method exhibits wide linear ranges (0.2-1000 μg L-1), low limits of detection (0.07-1.7 μg L-1), good precisions (intraday and inter-day RSDs < 5.4 %, n = 3), large enrichment factors (98.6-99.9), and less adsorbent consumption (3 mg). The extraction mechanism and selectivity of MMON-PANI are also evaluated in detail. This work proves the incorporation of PANI onto MMON is an efficient way to promote NSAIDs enrichment and provides a new strategy to synthesize multifunctional MON-based composites in sample pretreatment.

Preparation of cationic microporous organic network for efficient solid-phase extraction of nonsteroidal anti-inflammatory drugs from environmental water and milk samples

The overuse of nonsteroidal anti-inflammatory drugs (NSAIDs) poses many serious environmental and food safety concerns. Development of effective and sensitive sample pretreatment method for monitoring trace NSAIDs from complex samples is of great significance. Depending on the ionic and aromatic structures of NSAIDs, a cationic microporous organic network (MON) named TEPM-BBDC with large specific surface area, good solvent and thermal stabilities, and numerous interaction sites was designed and prepared for efficient solid-phase extraction (SPE) of four typical NSAIDs (flurbiprofen, ketoprofen, naproxen, and diclofenac sodium) from environmental water and milk samples. By anchoring the ionic groups in the conjugated MON frameworks, the prepared TEPM-BBDC offered good extraction for NSAIDs based on the π-π, hydrophobic, ion exchange, and electrostatic interactions. Under the optimal extraction conditions (initial concentration of each NSAID: 200 g L-1; sample volume: 50 mL; desorption solvent: 1.5 mL of MeOH + 1 % NH3·H2O; sample loading rate: 5 mL min-1; NaCl concentration: 0 mmol L-1; pH = 5), the proposed TEPM-BBDC-SPE-HPLC-UV method owned wide linear range (0.50-1000 g L-1), low limits of detection (0.10-0.40 g L-1), large enrichment factors (92.2-99.2), good precisions (intra-day and inter-day, RSD% = 1.3-7.8 %, n = 6) and reproducibility (column-to-column, RSD% = 8.0 %, n = 3). The developed method also exhibited good recoveries (83.6-113.4 %) for the determination of NSAIDs in river water, lake water and milk samples. This work not only revealed the potential of TEPM-BBDC for SPE of ionic NSAIDs in complex samples, but also highlighted the prospect of ionic MONs in sample pretreatment.

Solvent and monomer regulation synthesis of core-shelled magnetic β-cyclodextrin microporous organic network for efficient extraction of estrogens in biological samples prior to HPLC analysis

The abnormal estrogens levels in human body can cause many side effects and diseases, but the quantitative detection of the trace estrogens in complex biological samples still remains great challenge. Here we reported the fabrication of a novel core-shell structured magnetic cyclodextrin microporous organic network (Fe3O4@CD-MON) for rapid magnetic solid phase extraction (MSPE) of four estrogens in human serum and urine samples prior to HPLC-UV determination. The uniform spherical core-shell Fe3O4@CD-MONs was successfully regulated by altering the reactive monomers and solvents. The Fe3O4@CD-MONs owned high specific surface area, good hydrophobicity, large superparamagnetism, and abundant extraction sites for estrogens. Under optimal conditions, the proposed MSPE-HPLC-UV method provided wide linearity range (2.0-400 μg L-1), low limits of detection (0.5-1.0 μg L-1), large enrichment factors (183-198), less adsorbent consumption (3 mg), short extraction time (3 min), and good stability and reusability (at least 8 cycles). The established method had also been successfully applied to the enrichment and detection of four estrogens in serum and urine samples with a recovery of 88.4-105.1 % and a relative standard deviation of 1.0-5.9 %. This work confirmed the feasibility of solvent and monomer regulation synthesis of Fe3O4@CD-MON composites, and revealed the great prospects of magnetic CD-MONs for efficient enrichment of trace estrogens in complex biological samples.

Removal and detection of phenols through an SPE-HPLC method using microporous organic networks as adsorbent

The design and development of a facile synthesis approach to construct novel materials for the rapid adsorption and removal of environmental pollutants are of significant interest. In this work, we report the rational design and facile synthesis of magnetic core-shell-based microporous organic networks, Fe3O4@MON-TBPT-TEB (TTMON, achieved by reacting 2,4,6-tris(p-bromophenyl) triazine and 1,3,5-triethynylbenzene) and Fe3O4@MON-TBPM-DEBP (TDMON, achieved by reacting tetrakis (4-bromophenyl) methane and 4-4'-diethynylbiphenyl). These MONs possessed excellent dispersity, electrostatic attraction as well as plenty of π-π and hydrophobic interaction sites enabled them to efficiently absorb targeted environmental pollutants. TTMON and TDMON exhibited excellent adsorption capacities of 440 and 510 mg g-1, respectively, at 25 °C for 2,4,6-trichlorophenol (TCP). TCP, 2,4-dichlorophenol (DCP), 2-naphthol (2-NT) and 4-nitrophenol (4-NP) from aqueous solution were treated by both MONs, followed by their analysis with high-performance liquid chromatography (HPLC). For TDMON, the proposed SPE-HPLC-UV method showed an LOD of 0.03 μg L-1, LOQ of 0.11 μg L-1, and a wide linear range of 1-1000 μg L-1 for TCP. The adsorption kinetics, thermodynamics, isotherms, effect of pH and humic acid (HA), ionic strength, regeneration, and reusability of the MONs were also studied. The results revealed that the novel-designed MONs have potential applications as efficient adsorbents in sample pretreatment.

Fabrication of a β-CD-functionalized magnetic microporous organic network for effective enrichment and detection of fluoroquinolone antibiotics in water samples

Fluoroquinolone (FQ) antibiotics, one of the leading environmental pollutants, have ecotoxic effects that can accumulate through ecosystems and harm human health. The determination of FQs is still difficult due to the complex matrix, many interfering factors, and low concentration. Hence, a magnetic microporous organic network (MON) composite denoted as Fe3O4@MON-NH2@CM-β-CD with excellent FQ adsorption performance was prepared by β-CD covalent modification of a MON. Based on the existence of π-π packing, hydrophobic interaction, and hydrogen bonding between Fe3O4@MON-NH2@CM-β-CD and FQs, a new magnetic solid phase extraction (MSPE) method for the enrichment of FQs was developed. Under optimized MSPE conditions, five FQs were detected by HPLC-UV with good linearity (R2 ≥ 0.9989) in the range of 0.02-1 μg mL-1, and detection limits (S/N = 3) in the range of 0.0014-0.0023 μg mL-1. The satisfactory recoveries ranged from 93.1 to 116.2% with RSDs lower than 8.39% when applied to actual environmental water samples. These results revealed that Fe3O4@MON-NH2@CM-β-CD as an adsorbent for MSPE had excellent performance for FQ extraction from real samples, and the MON material types were expanded through the functionalization of MONs, which would have great potential for further application in various analytical methods.

Amide and carboxyl dual-functionalized magnetic microporous organic networks for efficient extraction of cephalosporins

Cephalosporins (CEFs) are a class of widely used toxic antibiotics. Development of a rapid and sensitive method for detecting trace CEF residues in food samples is still challenging. Herein, we report preparation of an amide and carboxyl groups dual-functionalized core-shelled magnetic microporous organic network MMON-COOH-2CONH for efficient magnetic solid-phase extraction (MSPE) of CEFs from milk powder samples. Under optimal conditions, the established MMON-COOH-2CONH-MSPE-HPLC-UV method owns wide linear range (3-10000 µg kg-1), low limits of detection (1-3 µg kg-1), large enrichment factors (93.9-99.4), low adsorbent consumption (3 mg), and short extraction time (6 min). Synergistic extraction mechanisms of ionic bonding, hydrogen bonding, π-π, and hydrophobic interactions were elucidated by both theoretical density functional theory calculations and experimental data. This study confirms that preparation of dual-functionalized MMONs and introduction of ionic groups are feasible to promote MMONs application in sample pretreatment.

Fabrication of amino- and hydroxyl dual-functionalized magnetic microporous organic network for extraction of zearalenone from traditional Chinese medicine prior to the HPLC determination

Efficient enrichment of trace zearalenone (ZEN) from the complex traditional Chinese medicine (TCM) samples is quite difficult, but of great significance for TCM quality control. Herein, we reported a novel magnetic solid phase extraction (MSPE) strategy for ZEN enrichment using the amino- and hydroxyl dual-functionalized magnetic microporous organic network (Fe3O4@MON-NH2-OH) as an advanced adsorbent combined with the high-performance liquid chromatography (HPLC) determination. Efficient extraction of ZEN was achieved via the possible hydrogen bonding, hydrophobic, and π-π interactions between Fe3O4@MON-NH2-OH and ZEN. The adsorption capacity of Fe3O4@MON-NH2-OH for ZEN was 215.0 mg g-1 at the room temperature, which was much higher than most of the reported adsorbents. Under the optimal condition, the developed Fe3O4@MON-NH2-OH-MSPE-HPLC method exhibited wide linear range (5-2500 μg L-1), low limits of detection (1.4-35 μg L-1), less adsorbent consumption (5 mg), and large enhancement factor (95) for ZEN. The proposed method was successfully applied to detect trace ZEN from 10 kinds of real TCM samples. Conclusively, this work demonstrates the Fe3O4@MON-NH2-OH can effectively extract trace ZEN from the complex TCM matrices, which may open up a new way for the application of MONs in the enrichment and extraction of trace contaminants or active constituents from the complex TCM samples.

Length-controlled hydrophobic CF3-COF as a highly efficient absorbent coating for dual-mode solid-phase microextraction of sixteen polycyclic aromatic hydrocarbons in water samples

Polycyclic aromatic hydrocarbons (PAHs), a group of seriously hazardous environmental contaminants, have attracted extensive attention due to their carcinogenicity, genotoxicity, mutagenicity, and ubiquity. In this work, the excellent hydrophobic trifluoromethyl-enriched covalent organic framework (CF3-COF) was designed and synthesized as coating of solid-phase microextraction (SPME). The CF3-COF offered a high adsorption selectivity for PAHs, which could be attributed to the multiple interactions between the CF3-COF and PAHs, including hydrophobicity interaction, π-π and H bond interactions. Furthermore, headspace (HS) and direct immersion (DI) dual-mode solid-phase microextraction (HS/DI-SPME) were innovatively integrated as a dual-mode extraction by varying the length of SPME coating on stainless-steel, which could simultaneously and efficiently extract 16 PAHs with different volatile. Amazingly, the proposed strategy achieved fast adsorption for PAHs and shortened the adsorption equilibrium time to 15 min. By further integrating with gas chromatography tandem mass spectrometry (GC-MS/MS), PAHs could be detected in the range of 0.008-0.16 ng mL-1 with a quantitative limit of 0.029-0.47 ng mL-1, respectively. The recoveries of PAHs in water samples ranged from 80.84 to 117.67 %. This work indicates that the dual-mode CF3-COF-SPME is a promising candidate for the enrichment of multiple hazardous substances in complicated samples.

Sacrificial template synthesis of hollow sulfonate group functionalized microporous organic network for efficient solid phase extraction of sulfonamide antibiotics from milk and honey samples

The highly conjugated and hydrophobic characteristics of microporous organic networks (MONs) have largely impeded their broad applications in sample pretreatment especially for the polar or ionic analytes. In this work, a novel uniform hollow shaped sulfonate group functionalized MON (H-MON-SO3H-2) was synthesized via the sacrificial template method for the efficient solid phase extraction (SPE) of sulfonamides (SAs) from environmental water, milk, and honey samples prior to HPLC analysis. H-MON-SO3H-2 exhibited large specific surface area, penetrable space, good stability, and numerous hydrogen bonding, electrostatic, hydrophobic and π-π interaction sites, allowing sensitive SPE of SAs with wide linear range (0.150-1000 μg L-1), low limit of detection (0.045-0.188 μg L-1), good precisions (intra-day and inter-day RSD < 7.3%, n = 5), large enrichment factors (95.7-98.5), high adsorption capacities (250.4-545.0 mg g-1), and satisfactory reusability (more than 80 times). Moreover, the established method was successfully applied to extract SAs from spiked samples with the recoveries of 86.1-104.3%. This work demonstrated the great potential of H-MON-SO3H-2 in the efficient SPE of trace SAs in complex environmental water and food samples and revealed the prospect of hollow MONs in sample pretreatment.

Fluorine-functionalized magnetic amino microporous organic network for enrichment of perfluoroalkyl substances

Perfluoroalkyl substances (PFAS) are persistent organic pollutants that pose significant risks to human health and the environment. Efficient and selective enrichment of these compounds was crucial for their accurate detection and quantification in complex matrices. Herein, we report a novel magnetic solid-phase extraction (MSPE) method using fluorine-functionalized magnetic amino-microporous organic network (Fe3O4@MONNH2@F7) adsorbent for the efficient enrichment of PFAS from aqueous samples. The core-shell Fe3O4@MONNH2@F7 nanosphere was synthesized, featuring magnetic Fe3O4 nanoparticles as the core and a porous amino-functionalized MONs coating as the shell, which was further modified by fluorination. The synthesized adsorbent material exhibited high specific surface area, hydrophobicity, and abundant fluorine groups, facilitating efficient and selective adsorption of PFAS via electrostatic attraction, hydrophobic-hydrophobic interactions, fluorine-fluorine interactions, π-CF interactions and hydrogen bonding. Furthermore, the MSPE method coupled with ultra-high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) allowed for the rapid, sensitive, and accurate determination of ultra-trace PFAS in real water samples, human serum, and human follicular fluid. Under optimal conditions, the established MSPE method demonstrated a linear range (2 to 2000 ng L-1), with a correlation coefficient exceeding 0.9977, low limits of detection ranging from 0.54 to 1.47 ng L-1, with a relative standard deviation (RSD) < 9.1%. Additionally, the method showed excellent performance in complex real samples (recovery ratio of 81.7 to 121.6 %). The adsorption mechanism was investigated through kinetic, isotherm, and molecular simulation studies, revealing that the introduction of fluorine groups enhanced the hydrophobic interaction and fluorine-fluorine attraction between the adsorbent and PFAS. This work provides a proof-of-concept strategy for designing adsorbent materials with high efficiency and selectivity by post-modification, which has great potential for the detection and analysis of PFAS in complex samples.

Efficient adsorption of chloroquine phosphate by a novel sodium alginate/tannic acid double-network hydrogel in a wide pH range

In this work, a novel double-network composite hydrogel (SA/TA), composed of sodium alginate (SA) and tannic acid (TA), was designed and fabricated by a successive cross-linking method using Ti(IV) and Ca(II) as crosslinkers. SA/TA exhibited reinforced mechanical strength and anti-swelling properties because of the double-network structure. SA/TA was used as an adsorbent for removal of a popular antiviral drug, chloroquine phosphate (CQ), in water. The adsorption performance of SA/TA was systematically investigated, to study various effects including those of TA mass content, solution pH, adsorption time, and initial CQ concentration. Adsorption was also examined in presence of inorganic and organic coexisting substances commonly found in wastewater, and under different actual water samples. Batch experimental results indicated that SA/TA could maintain higher and more stable CQ uptakes within a wide solution pH range from 3.0 to 10.0, compared to its precursor, SA hydrogel, owing to the addition of TA-Ti(IV) coordination network. The maximum experimental CQ uptake exhibited by the 1:1 (by wt) SA/TA (SA/TA2) was as high as 0.699 mmol/g at the initial pH of 9.0. A high concentration of coexisting NaCl evidently reduced the CQ uptakes of SA/TA2 due to the electrostatic shielding effect, moreover, divalent cations including Ca(II) and Mg(II) also inhibited the adsorption of CQ due to competitive adsorption. However, humic acid had little effect on this adsorption. Considering the apparent adsorption performance, the aforementioned effects of various factors and the spectroscopic characterizations, multi-interactions are suggested for adsorption including chelation, electrostatic interactions, π-π electron donor-acceptor interaction and hydrogen bonding. SA/TA showed a slight loss in adsorption capacity toward CQ and sustained physicochemical structural stability, even after six adsorption-desorption cycles. In addition to CQ, SA/TA could be efficiently used for adsorption of two other antivirus drugs, namely, hydroxychloroquine sulfate and oseltamivir phosphate. This work provides an effective strategy for the design and fabrication of novel adsorbents that can effectively adsorb antiviral drugs over a wide pH range.

Fabrication of magnetic Fe3O4 doped β-cyclodextrin microporous organic network for the efficient extraction of endocrine disrupting chemicals from food takeaway boxes

Endocrine disrupting chemicals (EDCs) are a typical class of natural or man-made endogenous hormone agonists or antagonists that can directly or potentially interfere with human endocrine system. However, it is still difficult to analyze trace EDCs directly from complex environment and food matrices. Therefore, the proper sample pretreatment is highly desired and the preparation of efficient adsorbents is of great challenge and importance. Herein, we report the facile one-pot solvothermal synthesis of Fe3O4 nanoparticle doped magnetic β-cyclodextrin microporous organic network composites (MCD-MONs) for the magnetic solid phase extraction (MSPE) of four phenolic EDCs in water and food takeaway boxes prior to the high-performance liquid chromatography analysis. The sheet-like Fe3O4 doped MCD-MONs offered good magnetic property (16.5 emu g-1) and stability, and provided numerous hydrogen bonding, hydrophobic, π-π, and host-guest interaction sites for EDCs. Under the optimal experimental conditions, the established method was successfully verified with wide linear range (2.0-1000 µg L-1), low limits of detection (0.6-1.0 µg L-1), good precisions (intra-day and inter-day RSDs < 5.2 %, n = 3), large enrichment factors (88-98) and adsorption capacity (90.3-255.8 mg g-1), short extraction time (6 min), less adsorbent consumption (3 mg), and good reusability (at least 8 times) for EDCs. The proposed method was successfully applied to detect the trace EDCs in real samples with the recovery of 84.0-99.7 %. This work demonstrated the great potential of MCD-MONs for the efficient MSPE of trace EDCs from complex food takeaway boxes and water samples and uncovered the prospect of CD-based MONs in sample pretreatment.

Fabrication of zwitterionic magnetic microporous organic network for efficient extraction of fluoroquinolone antibiotics from meat samples

A zwitterionic magnetic microporous organic network (MMON-SO3H-NH2) with numerous amino and sulfonic acid ion-pare binding sites was designed and synthesized for efficient magnetic solid-phase extraction (MSPE) of fluoroquinolones (FQs) from meat samples. The core-shell MMON-SO3H-NH2 offered large specific surface area, rapid magnetic responsiveness, good stability, and multiple binding sites for FQs. The density functional theory and independent gradient model evaluations confirmed hydrogen bonding, π-π and ion-pair interactions between MMON-SO3H-NH2 and FQs. Under the optimal conditions, the established MMON-SO3H-NH2-MSPE-HPLC-UV method gave wide linear range (0.15-1000 μg L-1), low limits of detection (0.05-4.5 μg L-1) and limits of quantitation (0.15-13 μg L-1), and high enrichment factors (82.1-99.6) using 3 mg of adsorbent. This work demonstrates that the preparation of zwitterionic MONs is an efficient way to promote the extraction performance of MONs for zwitterionic targets and provides an effective sample pretreatment method for enriching and monitoring FQs in complex food matrices.

Room-temperature synthesis of dual-functionalized magnetic microporous organic network for efficient extraction of vanillins in food

Microporous organic networks (MONs) are promising materials for the magnetic solid-phase extraction (MSPE) of trace targets from diverse complex samples. However, all the reported magnetic MONs (MMONs) are mono-functionalized and synthesized by refluxing at high temperatures, which is not an energy-efficient and environmentally friendly method. Here, for the first time, we report the room-temperature fabrication of a novel dual-functionalized MMON (MMON-B) for the efficient MSPE of typical vanillin additives from food samples prior to high-performance liquid chromatography (HPLC). The conjugated MMON-B with numerous -OH and -NH₂ groups afforded good extraction for vanillins via π-π, hydrophobic, and hydrogen-bonding interactions. The factors affecting the extraction were studied in detail. Under the optimal conditions, the developed MMON-B-MSPE-HPLC-UV method exhibited wide linear range (0.50-1200 μg L^-1), low limits of detection (0.10-0.15 μg L^-1), and good reusability and stability. Therefore, MMON-B was successfully used to enrich vanillins in complex food samples. The morphology and extraction efficiency of the room-temperature synthesized MMON-B were comparable with those of the MMON-B synthesized via the conventional reflux method, indicating that the room-temperature fabrication method is a good alternative to the reflux method. This study presents the feasibility of using a room-temperature method for synthesizing dual-functionalized MONs, and the findings may significantly promote the application of MONs in the MSPE of trace targets from complex matrices.

Construction of Stable Magnetic Vinylene-Linked Covalent Organic Frameworks for Efficient Extraction of Benzimidazole Fungicides

Covalent organic frameworks (COFs) have attracted impressive interest in separation on aqueous media. Herein, we integrated the stable vinylene-linked COFs with magnetic nanosphere via the monomer-mediated in situ growth strategy to construct a crystalline Fe₃O₄@v-COF composite for enrichment and determination of benzimidazole fungicides (BZDs) from complex sample matrices. The Fe₃O₄@v-COF has a crystalline assembly, high surface area, porous character together with a well-defined core-shell structure, and serves as progressive pretreatment materials for magnetic solid phase extraction (MSPE) of BZDs. Adsorption mechanism studies revealed that the extended conjugated system and numerous polar cyan groups on v-COF provides abundant π-π and multiple hydrogen bonding sites, which are conducive to interact with BZDs collaboratively. Fe₃O₄@v-COF also displayed enrichment effects to various polar pollutions with conjugated structures and hydrogen-bonding sites. Fe₃O₄@v-COF-based MSPE-high-performance liquid chromatography exhibited the low limit of detection, wide linearity, and good precision. Moreover, Fe₃O₄@v-COF showed better stability, enhanced extraction performance, and more sustainable reusability in comparison with its imine-linked counterpart. This work proposes a feasible strategy on constructing the crystalline stable magnetic vinylene-linked COF composite for the determination of trace contaminants in complex food matrices.

Post-synthetic modification of a magnetic covalent organic framework with alkyne linkages for efficient magnetic solid-phase extraction and determination of trace basic orange II in food samples

Efficient magnetic solid phase extraction using covalent organic frameworks (COFs) can find important applications in food safety. In this work, a sulfonate-functionalized magnetic COF (Fe₃O₄@COF-SO₃Na) was synthesized by self-polycondensation of two-in-one monomer 1,6-bis(4-formylphenyl)-3,8-bis((4-aminophenyl) ethynyl)) pyrene (BFBAEPy) on the surface of aminated Fe₃O₄ and a thiol-yne click reaction. It was further adopted as an adsorbent for the efficient magnetic solid-phase extraction (MSPE) of basic orange II. The selective adsorption experiment indicated that it displayed selective adsorption ability to basic orange II due to the ion exchange, hydrogen bonds, and π-π interactions. Under the optimized conditions, the proposed MSPE method coupled with HPLC-DAD showed excellent linearity in the range of 0.05-0.5 µg/mL (R² = 0.9997) for basic orange II. The lower limits of detection (LODs) for basic orange II were 1.0-1.4 µg/L for three food samples: yellow croaker, paprika and dried bean curd. The recoveries were 90.1-98.8% with relative standard deviations (RSDs) below 4.2%. Therefore, this work provides an effective strategy to modify magnetic COFs as absorbents in MSPE. Due to the tunability of functional groups in thiol‑yne click reactions, the functional groups of magnetic COFs can be readily designed to enrich their multifunctional applications. Meanwhile, this work proposed a new method to detect trace amounts of basic orange II in food samples.

Synthesis of crown ether-based microporous organic networks: A new type of efficient adsorbents for chlorophenols

Microporous organic networks (MONs) are a booming class of functional materials in elimination of environmental pollutants. However, the limit varieties of MONs still restrict their broad applications. Here we report the synthesis of a novel type of crown ether (CE)-based MONs via the coupling between brominated 18-crown-6 ether and different aromatic alkynyls. The constructed CE-based MONs integrates the good conjugation property of MONs and the inherent host-guest binding sites of CE, allowing the ultrafast and efficient adsorption and removal of a typical environmental priority pollutant 2,4,6-trichlorophenol (2,4,6-TCP). The hydrophobic CE-based MONs can also address the recovery challenge of unstable discrete CE in most organic and inorganic solvents. All CE-based MONs displayed fast adsorption kinetics (< 3 min) and large adsorption capacities (229.1-341.7 mg g^-1) for 2,4,6-TCP. The CE-based MONs also gave stable adsorption capacities for 2,4,6-TCP in pH range of 4.0-6.0, NaCl concentration of 0-40 mg L^-1, HA concentration of 0-30 mg L^-1, or H₂O₂ ratio of < 5 %. Density functional theory calculation, Fourier transform infrared and X-ray photoelectron spectra evaluation revealed adsorption process involved hydrophobic, π-π and hydrogen bonding interactions. The CE-based MONs also showed favorable reusability and good adsorption for other toxic chlorophenols. This work highlights the potential of CE-based MONs in contaminants elimination.

Nitrogen-rich based conjugated microporous polymers for highly efficient adsorption and removal of COVID-19 antiviral drug chloroquine phosphate from environmental waters

Chloroquine phosphate (CQP) has been suggested as an important and effective clinical reliever medication for the 2019 coronavirus (COVID-19). Nevertheless, its excessive use will inevitably cause irreparable damage to the entire ecosystem, thereby posing a considerable environmental safety concern. Hence, the development of highly-efficient methods of removing CQP from water pollution sources, e.g., effluents from hospitals and pharmaceutical factories is significant. This study reported the fabrication of novel C—N bond linked conjugated microporous polymers (CMPs) (BPT–DMB–CMP) with multiple nitrogen-rich anchoring sites for the quick and efficient removal of CQP from aqueous solutions. The irreversible covalent C—N bond linked in the internal framework of BPT–DMB–CMP endowed it with good chemical stability and excellent adsorbent regeneration. With its predesigned functional groups (i.e., rich N—H bonds, triazine rings, and benzene rings) and large area surface (1,019.89 m²·g⁻¹), BPT–DMB–CMP demonstrated rapid adsorption kinetics (25 min) and an extraordinary adsorption capacity (334.70 mg·g⁻¹) for CQP, which is relatively higher than that of other adsorbents. The adsorption behavior of CQP on BPT–DMB–CMP corresponded with Liu model and mixed-order model. Based on the density functional theory (DFT) calculations, X-ray photoelectron spectroscopy (XPS), and adsorption comparisons test, the halogen bonding, and hydrogen bonding cooperates with π − π, C — H···π interactions and size-matching effect in the CQP adsorption system on BPT–DMB–CMP. The excellent practicability for the removal of CQP from real wastewater samples verified the prospect of practical application of BPT–DMB–CMP. BPT–DMB–CMP exhibited the application potentials for the adsorption of other antiviral drugs. This work opens up an efficient, simple, and high adsorption capacity way for removal CQP.

Buchwald-Hartwig coupled conjugated microporous polymer for efficient removal COVID-19 antiviral drug famciclovir from waters: Adsorption behavior and mechanism

The consumption of famciclovir (FCV) has been increased dramatically since the outbreak of coronavirus in 2019, and the pollution and harm of FCV in waters are concerned. Here, by utilizing aryl halides on 2, 4, 6-tris(4-bromophenyl)- 1, 3, 5-triazine (BPT) and primary amine groups on benzidine (BZ), a novel conjugated microporous polymer, namely BPT-BZ-CMP, was synthesized by Buchwald-Hartwig coupling reaction and applied in the removal of FCV from aqueous solution firstly. The synthesized BPT-BZ-CMP were characterized by various methods, including FTIR, SEM, BET, and Zeta-potential. Due to the micropore structure and high specific surface area, it took only 30 min for BPT-BZ-CMP to adsorb FCV to reach an equilibrium, and the maximum adsorption capacity was 347.8 mg·g^-1. The Liu and pseudo-second-order kinetic models properly fit the adsorption equilibrium and kinetic data, respectively. The adsorption process was a spontaneous process, and the hydrogen bonding, π-π interaction and C-H···π interaction enhanced the adsorption of FCV on BPT-BZ-CMP. BPT-BZ-CMP maintained a good adsorption capacity after four consecutive adsorption-desorption cycle experiments. This study confirmed the potential of BPT-BZ-CMP as efficient sorbent to remove FCV from aqueous solutions.

Core-shell-structured magnetic covalent organic frameworks for effective extraction of parabens prior to their determination by HPLC

Covalent organic framework (COF)-decorated magnetic nanoparticles (Fe₃O₄@DhaTab) with core-shell structure have been synthesized by one-pot method. The prepared Fe₃O₄@DhaTab was well characterized, and parameters of magnetic solid-phase extraction (MSPE) for parabens were also investigated in detail. Under optimized conditions, the adsorbent dosage was only 3 mg and extraction time was 10 min. The developed Fe₃O₄@DhaTab-based MSPE-HPLC analysis method offered good linearity (0.01-20 μg mL^-1) with R² (0.999) and low limits of detection (3.3-6.5 μg L^-1) using UV detector at 254 nm. The proposed method was applied to determine four parabens in environmental water samples with recoveries in the range 64.0-105% and relative standard deviations of 0.16-7.8%. The adsorption mechanism was explored and indicated that porous DhaTab shell provided π-π, hydrophobic, and hydrogen bonding interactions in the MSPE process. The results revealed the potential of magnetic-functionalized COFs in determination of environmental contaminants.

Monodispersed CaCO3@hydroxyapatite/magnetite microspheres for efficient and selective extraction of benzoylurea insecticides in tea beverages samples

A novel monodispersed CaCO₃@hydroxyapatite/magnetite microsphere (CaCO₃ @HAP/Fe₃O₄) was prepared via an in-situ growth strategy, and applied as an adsorbent for efficient and selective adsorption of benzoylurea insecticides (BUs) in various tea beverages samples. The sorbent exhibited uniformity in particle size, good mono-dispersibility and excellent solvent stability. The adsorption equilibrium of BUs (100 ng/mL) in 10 mL of tea beverages samples was achieved on 20 mg of CaCO₃ @HAP/Fe₃O₄ within 10 min. The adsorption followed pseudo-second-order kinetics and Langmuir models and the maximum adsorption capacities of 131.9-161.3 mg/g were accomplished via hydrophobic interactions, hydrogen bonding, and the affinity of F atom and Ca²⁺. Coupled with high performance liquid chromatography, the method offered wide linear ranges of 0.8-1000 ng/mL with correlation coefficients (r) ≥ 0.9995, low limits of detection of 0.2-0.3 ng/mL and large enrichment factors of 75.7-102. The recoveries ranged from 75.7%- 102% with intra- and inter-day precisions of 1.9%- 9.3% and 1.6%- 11.8%, respectively. In addition, CaCO₃ @HAP/Fe₃O₄ could be easily regenerated and reused at least 10 times with no significant loss of recovery. These results revealed an alternative strategy for fast and convenient determination of BUs in tea beverages samples and proved the great feasibility of CaCO₃ @HAP/Fe₃O₄ in the application for the selective adsorption of BUs.