Alkali Metal Cations Modulate the Energy Level of SnO2 via Micro-agglomerating and Anchoring for Perovskite Solar Cells

Composite SnO2-K2S ETL for energy level regulation and electron mobility enhancement in perovskite solar cells

High-performance perovskite solar cells commonly utilize SnO2 as the electron transport layer (ETL), which is vital for perovskite crystallization and defect regulation, yet energy level mismatch, oxygen vacancies in SnO2, and defects at the buried interface impede the device's photovoltaic performance. Therefore, we found that incorporating K2S into the SnO2 layer effectively regulated the energy levels and occupied oxygen vacancies, enhancing the electron mobility of the composite SnO2-K2S ETL and improving the interface quality to promote efficient electron extraction and transport. Consequently, the device based on SnO2-K2S ETL showed an enhanced photovoltaic performance with power conversion efficiency of to 23.28%.

LiOH Additive Triggering Beneficial Aging Effect of SnO2 Nanocrystal Colloids for Efficient Wide-Bandgap Perovskite Solar Cells

Commercial SnO2 nanocrystals used for producing electron transporting layers (ETLs) of perovskite solar cells (PSC) are prone to aggregation at room temperature and contain many structural defects. Herein, we report that the LiOH additive can simultaneously delay the aggregation and donate the beneficial aging effect to SnO2 nanocrystals. The resulting SnO2 ETLs show the desired characteristics, including a broadened absorption range, reduced defects, improved transporting properties, and decreased work function. Meanwhile, perovskite Cs0.15FA0.65MA0.20Pb(I0.80Br0.20)3 films with a wide bandgap of 1.68 eV grown on them exhibit the pure phase, higher crystallinity, fewer defects, better buried-interface contact, and more aligned energy levels with each other than the ones based on SnO2 nanocrystals without the LiOH additive and aging treatment. Hence, the average efficiencies are boosted from (18.79 ± 0.40)% to (20.16 ± 0.36)% for the resulting wide-bandgap PSCs, wherein the champion efficiency of 21.12% is achieved. In addition, the as-obtained PSCs possess good thermal and humidity stability.

Synergistic dual-layer passivation boosts efficiency and stability in perovskite solar cells using naphthol sulfonate

The performance and stability of perovskite solar cells (PSCs) are critically influenced by the interfacial properties between the perovskite absorption layer and the electron transport layer (ETL). This study introduces a novel interfacial engineering approach using dipotassium 7-hydroxynaphthalene-1,3-disulfonate (K-NDS) as a multifunctional passivator to enhance both the SnO2 ETL and the perovskite absorber layer. The sulfonic acid groups (-SO3-) in K-NDS effectively fill oxygen vacancies on the SnO2 surface, while the hydroxyl groups (-OH) passivate dangling bonds, improving the crystallinity of the perovskite film. Additionally, the diffusion of K+ from the SnO2 ETL into the perovskite layer optimizes energy level alignment, thereby enhancing charge carrier extraction and transport. This bifacial passivation strategy has significantly improved both the power conversion efficiency (PCE) and long-term stability of PSCs. The modified devices achieved a champion PCE of 23.00% and an open-circuit voltage (VOC) of 1.172 V. Furthermore, these devices maintained 75% of their initial PCE even after 1000 hours of storage under indoor environmental conditions. This work demonstrates the effectiveness of synergistic interfacial passivation in advancing the performance and durability of PSCs.

Tin-Lead Perovskite Solar Cells with Preferred Crystal Orientation by Buried Interface Approach

Mixed tin-lead perovskite solar cells (PSCs) have garnered much attention for their ideal bandgap and high environmental research value. However, poly (3,4-ethylenedioxythiophene): poly (styrene sulfonate) (PEDOT: PSS), widely used as a hole transport layer (HTL) for Sn-Pb PSCs, results in unsatisfactory power conversion efficiency (PCE) and long-term stability of PSCs due to its acidity and moisture absorption. A synergistic strategy by incorporating histidine (HIS) into the PEDOT: PSS HTL is applied to simultaneously regulate the nucleation and crystallization of perovskite (PVK). HIS neutralizes the acidity of PEDOT: PSS and enhances conductivity. Especially, the coordination of the C═N and -COO- functional groups in the HIS molecule with Sn2+ and Pb2+ induces vertical growth of PVK film, resulting in the release of residual surface stress. Additionally, this strategy also optimizes the energy level alignment between the perovskite layer and the HTL, which improves charge extraction and transport. With these cooperative effects, the PCE of Sn-Pb PSCs reaches 21.46% (1 sun, AM1.5), maintaining excellent stability under a nitrogen atmosphere. Hence, the buried interface approach exhibits the potential for achieving high-performance and stable Sn-Pb PSCs.

Ce-Doped SnO2 Electron Transport Layer for Minimizing Open Circuit Voltage Loss in Lead Perovskite Solar Cells

In the planar heterostructure of perovskite-based solar cells (PSCs), tin oxide (SnO2) is a material that is often used as the electron transport layer (ETL). SnO2 ETL exhibits favorable optical and electrical properties in the PSC structures. Nevertheless, the open circuit voltage (VOC) depletion occurs in PSCs due to the defects arising from the high oxygen vacancy on the SnO2 surface and the deeper conduction band (CB) energy level of SnO2. In this research, a cerium (Ce) dopant was introduced in SnO2 (Ce-SnO2) to suppress the VOC loss of the PSCs. The CB minimum of SnO2 was shifted closer to that of the perovskite after the Ce doping. Besides, the Ce doping effectively passivated the surface defects on SnO2 as well as improved the electron transport velocity by the Ce-SnO2. These results enabled the power conversion efficiency (PCE) to increase from 21.1% (SnO2) to 23.0% (Ce-SnO2) of the PSCs (0.09 cm2 active area) with around 100 mV of improved VOC and reduced hysteresis. Also, the Ce-SnO2 ETL-based large area (1.0 cm2) PSCs delivered the highest PCE of 22.9%. Furthermore, a VOC of 1.19 V with a PCE of 23.3% was demonstrated by Ce-SnO2 ETL-based PSCs (0.09 cm2 active area) that were treated with 2-phenethylamine hydroiodide on the perovskite top surface. Notably, the unencapsulated Ce-SnO2 ETL-based PSC was able to maintain above 90% of its initial PCE for around 2000 h which was stored under room temperature condition (23-25 °C) with a relative humidity of 40-50%.

Improving Thermal Stability of High-Efficiency Methylammonium-Free Perovskite Solar Cells via Chloride Additive Engineering

Tin dioxide (SnO2), in perovskite solar cells (PSCs), stands out as the material most suited to the electron transport layer (ETL), yielding advantages with regard to ease of preparation, high mobility, and favorable energy level alignment. Nonetheless, there is a chance that energy losses from defects in the SnO2 and interface will result in a reduction in the Voc. Consequently, optimizing the interfaces within solar cell devices is a key to augmenting both the efficiency and the stability of PSCs. Herein this present study, we introduced butylammonium chloride (BACl) into the SnO2 ETL. The resulting optimized SnO2 film mitigated interface defect density, thereby improving charge extraction. The robust bonding capability of negatively charged Cl- ions facilitated their binding with noncoordinated Sn4+ ions, effectively passivating defects associated with oxygen vacancies and enhancing charge transport within the SnO2 ETL. Concurrently, doped BA+ and Cl- diffused into the perovskite lattice, fostering perovskite grain growth and reducing the defects in perovskite. In comparison to the control device, the Voc saw a 70 mV increase, achieving a champion efficiency of 22.86%. Additionally, following 1000 h of ambient storage, the unencapsulated device based on SnO2 preburied with BACl retained around 90% of its initial photovoltaic conversion efficiency.

One-Stone-for-Two-Birds Method to Improve the SnO2 Layers for High Power-per-Weight Flexible Perovskite Solar Cell Mini-modules

Maintaining the power conversion efficiency (PCE) of flexible perovskite solar cells (fPSCs) while decreasing their weight is essential to utilize their lightweight and flexibility as much as possible for commercialization. Strengthening the interfaces between functional layers, such as flexible substrates, charge transport layers, and perovskite active layers, is critical to addressing the issue. Herein, we propose a feasible and one-stone-for-two-birds method to improve the electron transport layer (ETL), SnO2, and the interface between the ETL and perovskite layer simultaneously. In detail, poly(acrylate ammonium) (PAAm), a low-cost polymer with a long chain structure, is added into the SnO2 aqueous solution to reduce the aggregation of SnO2 nanoparticles, resulting in the deposition of a conformal and high-quality ETL film on the tin-doped indium oxide film surface. Simultaneously, PAAm addition can effectively regulate the crystallization of the perovskite films, strengthening the interface between the SnO2 film and the buried surface of the perovskite layer. The outstanding PCEs of 22.41% on small-scale fPSCs and 18.54% on fPSC mini-modules are among the state-of-the-art n-i-p type fPSCs. Moreover, the fPSC mini-module on the 20 μm-thick flexible substrate shows a comparable PCE with that of the fPSC mini-module on the 125 μm-thick flexible substrate, exhibiting a high power-to-weight of 5.097 W/g. This work provides an easy but essential direction for further applications of fPSCs in diverse scenarios.

Unraveling the Mechanism of Alkali Metal Fluoride Post-Treatment of SnO2 for Efficient Planar Perovskite Solar Cells

The facile synthesis and beneficial properties of tin oxide have driven the development of efficient planar perovskite solar cells (PSCs). To increase the PSC performance, alkali salts are used to treat the SnO2 surface to minimize the defect states. However, the underlying mechanism of alkali cations' role in the PSCs needs further exploration. Herein the effect of alkali fluoride salts (KF, RbF, and CsF) on the properties of SnO2 and PSC performance is investigated. The results show different alkali have significant roles depending on their nature. Larger cations Cs+ preferably locate at the SnO2 film surface to passivate surface defects and enhance conductivity, while smaller cations like Rb+ or K+ cations tend to diffuse into the perovskite layer to reduce trap density of the material. The former effect leads to enhanced fill factor while the latter effect increases the open circuit voltage of the device. It is then demonstrated that a dual cation post-treatment of the SnO2 layer with RbF and CsF achieves PSC with a significantly higher power conversion efficiency (PCE) of 21.66% compared to pristine PSC with a PCE of 19.71%. This highlights the significance of defect engineering of SnO2 using selective multiple alkali treatment to improve PSC performance.

Effects of the Electrical Properties of SnO2 and C60 on the Carrier Transport Characteristics of p-i-n-Structured Semitransparent Perovskite Solar Cells

Recently, metal halide perovskite-based top cells have shown significant potential for use in inexpensive and high-performance tandem solar cells. In state-of-the-art p-i-n perovskite/Si tandem devices, atomic-layer-deposited SnO2 has been widely used as a buffer layer in the top cells because it enables conformal, pinhole-free, and highly transparent buffer layer formation. In this work, the effects of various electrical properties of SnO2 and C60 layers on the carrier transport characteristics and the performance of the final devices were investigated using a numerical simulation method, which was established based on real experimental data to increase the validity of the model. It was found that the band alignment at the SnO2/C60 interface does, indeed, have a significant impact on the electron transport. In addition, as a general design rule, it was suggested that at first, the conduction band offset (CBO) between C60 and SnO2 should be chosen so as not to be too negative. However, even in a case in which this CBO condition is not met, we would still have the means to improve the electron transport characteristics by increasing the doping density of at least one of the two layers of C60 and/or SnO2, which would enhance the built-in potential across the perovskite layer and the electron extraction at the C60/SnO2 interface.

Synergistic Optimization of Buried Interface by Multifunctional Organic-Inorganic Complexes for Highly Efficient Planar Perovskite Solar Cells

For the further improvement of the power conversion efficiency (PCE) and stability of perovskite solar cells (PSCs), the buried interface between the perovskite and the electron transport layer is crucial. However, it is challenging to effectively optimize this interface as it is buried beneath the perovskite film. Herein, we have designed and synthesized a series of multifunctional organic-inorganic (OI) complexes as buried interfacial material to promote electron extraction, as well as the crystal growth of the perovskite. The OI complex with BF4- group not only eliminates oxygen vacancies on the SnO2 surface but also balances energy level alignment between SnO2 and perovskite, providing a favorable environment for charge carrier extraction. Moreover, OI complex with amine (- NH2) functional group can regulate the crystallization of the perovskite film via interaction with PbI2, resulting in highly crystallized perovskite film with large grains and low defect density. Consequently, with rational molecular design, the PSCs with optimal OI complex buried interface layer which contains both BF4- and -NH2 functional groups yield a champion device efficiency of 23.69%. More importantly, the resulting unencapsulated device performs excellent ambient stability, maintaining over 90% of its initial efficiency after 2000 h storage, and excellent light stability of 91.5% remaining PCE in the maximum power point tracking measurement (under continuous 100 mW cm-2 light illumination in N2 atmosphere) after 500 h.

Small Molecules Functionalized Zinc Oxide Interlayers for High Performance Low-Temperature Carbon-Based CsPbI2 Br Perovskite Solar Cells

The charge recombination resulting from bulk defects and interfacial energy level mismatch hinders the improvement of the power conversion efficiency (PCE) and stability of carbon-based inorganic perovskite solar cells (C-IPSCs). Herein, a series of small molecules including ethylenediaminetetraacetic acid (EDTA) and its derivatives (EDTA-Na and EDTA-K) are studied to functionalize the zinc oxide (ZnO) interlayers at the SnO₂ /CsPbI₂ Br buried interface to boost the photovoltaic performance of low-temperature C-IPSCs. This strategy can simultaneously passivate defects in ZnO and perovskite films, adjust interfacial energy level alignment, and release interfacial tensile stress, thereby improving interfacial contact, inhibiting ion migration, alleviating charge recombination, and promoting electron transport. As a result, a maximum PCE of 13.94% with a negligible hysteresis effect is obtained, which is one of the best results reported for low-temperature CsPbI₂ Br C-IPSCs so far. Moreover, the optimized devices without encapsulation demonstrate greatly improved operational stability.