Ordered Large-Pore Mesoporous Cr2O3 with Ultrathin Framework for Formaldehyde Sensing

Generation of Oxygen Vacancies in Metal-Organic Framework-Derived One-Dimensional Ni0.4Fe2.6O4 Nanorice Heterojunctions for ppb-Level Diethylamine Gas Sensing

Metal-organic frameworks (MOFs) are ideal sensing materials due to their distinctive morphologies, high surface area, and simple calcination to remove sacrificial MOF scaffolds. Oxygen vacancies (O_vs) can be efficiently generated by the thermal annealing of metal oxides in an inert atmosphere. Herein, MIL-53-based Fe and Fe/Ni-MOFs nanorices (NRs) were first prepared by using a solvothermal method, and then one-dimensional (1D) Fe₂O₃ and Ni_0.4Fe_2.6O₄ NRs were derived from the MOFs after calcination at 350 °C in an air and argon (Ar) atmosphere, respectively. It was found that Ar-annealed Ni_0.4Fe_2.6O₄ NRs have higher O_vs concentrations (82.11%) and smaller NRs (24.3 nm) than air-annealed NRs (65.68% & 31.5 nm). Beneficially, among the synthesized NRs, the Ar-Ni_0.4Fe_2.6O₄ NRs show a higher sensitivity to diethylamine (DEA) (R_a/R_g = 23 @ 5 ppm, 175 °C), low detection limit (R_a/R_g = 1.2 @ 200 ppb), wide dynamic response (R_a/R_g = 93.5@ 30 ppm), high stability (30 days), and faster response/recovery time (4 s/38 s). Moreover, the 1D nanostructure containing heterostructures offers excellent sensing selectivity and a wide detection range from 200 ppb to 30 ppm in the presence of DEA. The outstanding gas sensing behavior can be attributable to synergistic impact, structural advantages, high concentration of O_vs, and the heterojunction interface, which can have profound effects on gas sensor performance. This study provides a unique technique for constructing high-performance gas sensors for ppb-level DEA detection and the formation of O_vs in metal oxides without the need for any additives.

Microwave-assisted preparation of polysubstituted imidazoles using Zingiber extract synthesized green Cr2O3 nanoparticles

Cr₂O₃ nanoparticles were prepared using Zingiber officinal extract which were used as an efficient and reusable catalyst in the practical synthesis of polysubstituted imidazoles by means of a convenient reaction of aromatic aldehydes with ammonium acetate and benzil under microwave irradiation and H₂O as solvent. The structure of the compounds was studied by IR and ¹H-NMR spectrum. The most important benefits of this process are operational simplicity, reasonable reaction times, and excellent yield of products. The results show that the optimal conditions for the formation of imidazole derivatives are as follow: power of 400 W, reaction time of 4-9 min, H₂O as a solvent, and 15 mmol of catalyst amount.

Porous Cr2O3 Architecture Assembled by Nano-Sized Cylinders/Ellipsoids for Enhanced Sensing to Trace H2S Gas

How to achieve high sensing of Cr₂O₃-based sensors for harmful inorganic gases is still a challenge. To this end, Cr₂O₃ nanomaterials assembled from different building blocks were simply prepared by chromium salt immersion and air calcination with waste scallion roots as the biomass template. The hierarchical architecture calcined at 600 °C is constructed from nanocylinders and nanoellipsoids (named as Cr₂O₃-600), and also possesses multistage pore distribution for target gas accessibility. Interestingly, the synergism of two shapes of nanocrystals enables the Cr₂O₃-based sensor to realize highly sensitive detection of trace H₂S gas. At 170 °C, Cr₂O₃-600 exhibits a high response of 42.8 to 100 ppm H₂S gas, which is 3.45 times larger than that of Cr₂O₃-500 assembled from nanocylinders. Meanwhile, this sensor has a low detection limit of 1.0 ppb (S = 1.4), good selectivity, stability, and moisture resistance. These results show that the combination of nanosized cylinders/ellipsoids together with exposed (104) facet can effectively improve the sensing performance of the p-type Cr₂O₃ material. In addition, the Cr₂O₃-600 sensor shows satisfactory results for actual monitoring of the corruption process of fresh chicken.

How Chemoresistive Sensors Can Learn from Heterogeneous Catalysis. Hints, Issues, and Perspectives

The connection between heterogeneous catalysis and chemoresistive sensors is emerging more and more clearly, as concerns the well-known case of supported noble metals nanoparticles. On the other hand, it appears that a clear connection has not been set up yet for metal oxide catalysts. In particular, the catalytic properties of several different oxides hold the promise for specifically designed gas sensors in terms of selectivity towards given classes of analytes. In this review, several well-known metal oxide catalysts will be considered by first exposing solidly established catalytic properties that emerge from related literature perusal. On this basis, existing gas-sensing applications will be discussed and related, when possible, with the obtained catalysis results. Then, further potential sensing applications will be proposed based on the affinity of the catalytic pathways and possible sensing pathways. It will appear that dialogue with heterogeneous catalysis may help workers in chemoresistive sensors to design new systems and to gain remarkable insight into the existing sensing properties, in particular by applying the approaches and techniques typical of catalysis. However, several divergence points will appear between metal oxide catalysis and gas-sensing. Nevertheless, it will be pointed out how such divergences just push to a closer exchange between the two fields by using the catalysis knowledge as a toolbox for investigating the sensing mechanisms.

Alkali metal-incorporated spinel oxide nanofibers enable high performance detection of formaldehyde at ppb level

Sensing material with high sensitivity, excellent selectivity and ultra-low detection limit is crucial for monitoring formaldehyde, which is a kind of hazardous gas to human health at very low concentration. Some one-dimensional semiconductor metal oxides show acceptable responses towards formaldehyde. However, the detection limit and selectivity of these sensors are still not satisfied, especially at ppb level. Herein, alkali metals (K, Na) doped CdGa₂O₄ nanofibers with excellent formaldehyde sensing performance are prepared by an electrospinning method. These nanofibers have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), electron paramagnetic resonance spectroscopy (EPR), elemental mapping and other techniques. As a result, the sensor based on 7.5 at.% K doped CdGa₂O₄ gives remarkably improved formaldehyde sensing properties compared with that of pristine CdGa₂O₄. The greatly increased sensitivity and selectivity should be attributed to the increased chemisorbed oxygen and the enhanced basicity caused by the additional alkali metal, respectively. All in all, the 7.5 at.% K doped CdGa₂O₄ is a good candidate for the rapid detecting formaldehyde at ppb level.

Gas sensing mechanisms of metal oxide semiconductors: a focus review

In recent years, gas sensors have been increasingly used in industrial production and daily life. Metal oxide semiconductor gas sensing materials are favoured for their outstanding physical and chemical properties, low cost and simple preparation methods. However, the gas sensing mechanisms of metal oxide semiconductors have not been considered by researchers, resulting in omissions and errors in the interpretation of gas sensing mechanisms in many articles. This review organizes and introduces several common gas sensing mechanisms of metal oxide semiconductors in detail and classifies them into two categories. The scope and relationship of these mechanisms are clarified. In addition, this review selects four strategies for enhancing the gas sensing properties of metal oxide semiconductors and analyses the gas sensing mechanisms to highlight the importance of the gas sensing mechanism. Finally, some perspectives for future investigations on the gas sensing mechanisms of metal oxide semiconductors are discussed as well.

Gas sensors using ordered macroporous oxide nanostructures

Detection and monitoring of harmful and toxic gases have gained increased interest in relation to worldwide environmental issues. Semiconducting metal oxide gas sensors have been considered promising for the facile remote detection of gases and vapors over the past decades. However, their sensing performance is still a challenge to meet the demands for practical applications where excellent sensitivity, selectivity, stability, and response/recovery rate are imperative. Therefore, sensing materials with novel architectures and fabrication processes have been pursued with a flurry of research activity. In particular, the preparation of ordered macroporous metal oxide nanostructures is regarded as an intriguing candidate wherein ordered aperture sizes in the range from 50 nm to 1.5 μm can increase the chemical diffusion rate and considerably strengthen the performance stability and repeatability. This review highlights the recent advances in the fabrication of ordered macroporous nanostructures with different dimensions and compositions, discusses the sensing behavior evolution governed by structural layouts, hierarchy, doping, and heterojunctions, as well as considering their general principles and future prospects. This would provide a clear scale for others to tune the sensing performance of porous materials in terms of specific components and structural designs.

Graphene-Modified ZnO Nanostructures for Low-Temperature NO2 Sensing

This paper develops a novel ultrasonic spray-assisted solvothermal (USS) method to synthesize wrapped ZnO/reduced graphene oxide (rGO) nanocomposites with a Schottky junction for gas-sensing applications. The as-obtained ZnO/rGO-x samples with different graphene oxide (GO) contents (x = 0-1.5 wt %) are characterized by various techniques, and their gas-sensing properties for NO₂ and other VOC gases are also evaluated. The results show that the USS-derived ZnO/rGO samples exhibit high NO₂-sensing property at low operating temperatures (e.g., 70-130 °C) because of their high specific surface area and porous structures when compared with the ZnO/rGO sample obtained by the traditional precipitation method. The content of rGO shows an obvious effect on their NO₂-sensing properties, and the ZnO/rGO-0.5 sample has a high response of 62 operating at 130 °C, three times that of pure ZnO. The detection limit of the ZnO/rGO-0.5 sensor to NO₂ is as low as 10 ppb under the present test condition. In addition, the ZnO/rGO-0.5 sensor shows a highly selective response to NO₂ gas when compared with organic vapors and other inflammable or toxic gases. The theoretical and experimental analyses indicate that the enhancement in NO₂-sensing performance of the ZnO/rGO sensor is attributed to the formation of wrapped ZnO/rGO Schottky junctions.

Designing and Fabricating Ordered Mesoporous Metal Oxides for CO₂ Catalytic Conversion: A Review and Prospect

In the past two decades, great progress has been made in the aspects of fabrication and application of ordered mesoporous metal oxides. Ordered mesoporous metal oxides have attracted more and more attention due to their large surface areas and pore volumes, unblocked pore structure, and good thermal stabilities. Compared with non-porous metal oxides, the most prominent feature is their ability to interact with molecules not only on their outer surface but also on the large internal surfaces of the material, providing more accessible active sites for the reactants. This review carefully describes the characteristics, classification and synthesis of ordered mesoporous metal oxides in detail. Besides, it also summarizes the catalytic application of ordered mesoporous metal oxides in the field of carbon dioxide conversion and resource utilization, which provides prospective viewpoints to reduce the emission of greenhouse gas and the inhibition of global warming. Although the scope of current review is mainly limited to the ordered mesoporous metal oxides and their application in the field of CO₂ catalytic conversion via heterogeneous catalysis processes, we believe that it will provide new insights and viewpoints to the further development of heterogeneous catalytic materials.

Volatile Organic Compound Gas-Sensing Properties of Bimodal Porous α-Fe2O3 with Ultrahigh Sensitivity and Fast Response

Porous solid with multimodal pore size distribution provides plenty of advantages including large specific surface area and superior mass transportation to achieve high gas-sensing performances. In this study, α-Fe₂O₃ nanoparticles with bimodal porous structures were prepared successfully through a nanocasting pathway, adopting the bicontinuous 3D cubic symmetry mesoporous silica KIT-6 as the hard template. Its structure and morphology were characterized by X-ray diffraction, nitrogen adsorption-desorption, transmission electron microscopy, and so on. Furthermore, the gas sensor fabricated from this material exhibited excellent gas-sensing performance to several volatile organic compounds (acetone, ethyl acetate, isopropyl alcohol, n-butanol, ethanol, and methanol), such as ultrahigh sensitivity, rapid response speed (less than 10 s) and recovery time, good reproducibility, as well as stability. These would be associated with the desirable pore structure of the material, facilitating the molecules diffusion toward the entire sensing surface, and providing more active sensing sites for analytical gas.

Ordered mesoporous NiFe2O4 with ultrathin framework for low-ppb toluene sensing

Highly sensitive and selective detection against specific target gases, especially at low-ppb (part per billion) level, remain a great number of challenges in gas sensor applications. In this paper, we first present an ordered mesoporous NiFe₂O₄ for highly sensitive and selective detection against low-ppb toluene. A series of mesoporous NiFe₂O₄ materials were synthesized by templating from mesoporous silica KIT-6 and its framework thickness was reduced from 8.5 to 5 nm by varying the pore size of KIT-6 from 9.4 to 5.6 nm, accompanied with the increase of the specific surface area from 134 to 216 m² g^-1. The ordered mesoporous NiFe₂O₄ with both ultrathin framework of 5 nm and large specific surface area of up to 216 m² g^-1 exhibits a highest response (R_gas/R_air - 1 = 77.3) toward 1,000 ppb toluene at 230 °C and is nearly 7.3 and 76.7 times higher than those for the NiFe₂O₄ replica with thick framework and its bulk counterpart respectively, which also possesses a quite low limit of detection (<2 ppb), and good selectivity.

Microwave-assisted fast synthesis of hierarchical NiCo2O4 nanoflower-like supported Ni(OH)2 nanoparticles with an enhanced electrocatalytic activity towards methanol oxidation

NiCo₂O₄/Ni(OH)₂ synthesizing through microwave-assisted hydrothermal method and coordination of homogeneous precipitation, exhibiting excellent electrocatalytic activity.