Conductive Tough Hydrogels with a Staggered Ion-Coordinating Structure for High Self-Recovery Rate

Design of PEG-Based Hydrogels as Soft Ionic Conductors

Conductive hydrogels have gained interest in biomedical applications and soft electronics. To tackle the challenge of ionic hydrogels falling short of desired mechanical properties in previous studies, our investigation aimed to understand the pivotal structural factors that impact the conductivity and mechanical behavior of polyethylene glycol (PEG)-based hydrogels with ionic conductivity. Polyether urethane diacrylamide (PEUDAm), a functionalized long-chain macromer based on PEG, was used to synthesize hydrogels with ionic conductivity conferred by incorporating ions into the liquid phase of the hydrogel. The impact of salt concentration, water content, temperature, and gel formation on both mechanical properties and conductivity was characterized to establish parameters for tuning hydrogel properties. To further expand the range of conductivity available in these ionic hydrogels, 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) was incorporated as a single copolymer network or double network configuration. As expected, conductivity in these ionic gels was primarily driven by ion diffusivity and charge density, which were dependent on hydrogel network formation and swelling. Copolymer network structure had minimal effect on the conductivity, which was primarily driven by counter-ion equilibrium; however, the mechanical properties and equilibrium swelling were strongly dependent on network structure. The structure-property relationships elucidated here enable the rationale design of this new double network hydrogel to achieve target properties for a broad range of biomedical applications.

The Influence of the Structural Architecture on the Swelling Kinetics and the Network Behavior of Sodium-Alginate-Based Hydrogels Cross-Linked with Ionizing Radiation

The present work discusses the influence of the structural architecture of sodium alginate-co-acrylic acid-poly(ethylene) oxide hydrogels, crosslinked through electron beam (e-beam) radiation processing. The most important properties of the hydrogels were studied in detail to identify a correlation between the architecture of the hydrogels and their properties. Furthermore, the effect of sodium alginate (NaAlg) concentration, the amounts of the polymer blend, and the size of the samples on hydrogel properties were investigated. The results show that the hydrogels cross-linked (0.5% and 1% NaAlg) with 12.5 kGy exhibit improved physicochemical properties. High gel fraction levels (exceeding 83.5-93.7%) were achieved. Smaller hydrogel diameter (7 mm) contributed to a maximum swelling rate and degree of 20.440%. The hydrogel network was dependent on the hydrogels' diameter and the amount of polymer blend used. The hydrogels best suited the first-order rate constants and exhibited a non-Fickian diffusion character with diffusion exponent values greater than 0.5. This study indicates that the cross-linked hydrogel has good properties, particularly because of its high degree of swelling and extensive stability (more than 180 h) in water. These findings show that hydrogels can be effectively applied to the purification of water contaminated with metals, dyes, or even pharmaceuticals, as well as materials with a gradual release of bioactive chemicals and water retention.

Dynamic Metal-Coordinated Adhesive and Self-Healable Antifreezing Hydrogels for Strain Sensing, Flexible Supercapacitors, and EMI Shielding Applications

Dynamic metal-coordinated adhesive and self-healable hydrogel materials have garnered significant attention in recent years due to their potential applications in various fields. These hydrogels can form reversible metal-ligand bonds, resulting in a network structure that can be easily broken and reformed, leading to self-healing capabilities. In addition, these hydrogels possess excellent mechanical strength and flexibility, making them suitable for strain-sensing applications. In this work, we have developed a mechanically robust, highly stretchable, self-healing, and adhesive hydrogel by incorporating Ca2+-dicarboxylate dynamic metal-ligand cross-links in combination with low density chemical cross-links into a poly(acrylamide-co-maleic acid) copolymer structure. Utilizing the reversible nature of the Ca2+-dicarboxylate bond, the hydrogel exhibited a tensile strength of up to ∼250 kPa and was able to stretch to 15-16 times its original length. The hydrogel exhibited a high fracture energy of ∼1500 J m-2, similar to that of cartilage. Furthermore, the hydrogel showed good recovery, fatigue resistance, and fast self-healing properties due to the reversible Ca2+-dicarboxylate cross-links. The presence of Ca2+ resulted in a highly conductive hydrogel, which was utilized to design a flexible resistive strain sensor. This hydrogel can strongly adhere to different substrates, making it advantageous for applications in flexible electronic devices. When adhered to human body parts, the hydrogel can efficiently detect limb movements. The hydrogel also exhibited excellent performance as a solid electrolyte for flexible supercapacitors, with a capacitance of ∼260 F/g at 0.5 A/g current density. Due to its antifreezing and antidehydration properties, this hydrogel retains its flexibility at subzero temperatures for an extended period. Additionally, the porous network and high water content of the hydrogel impart remarkable electromagnetic attenuation properties, with a value of ∼38 dB in the 14.5-20.5 GHz frequency range, which is higher than any other hydrogel without conducting fillers. Overall, the hydrogel reported in this study exhibits diverse applications as a strain sensor, solid electrolyte for flexible supercapacitors, and efficient material for electromagnetic attenuation. Its multifunctional properties make it a promising candidate for use in various fields as a state-of-the-art material.

Ionic Crosslinked Hydrogel Films for Immediate Decontamination of Chemical Warfare Agents

This study describes the development of hydrogel formulations with ionic crosslinking capacity and photocatalytic characteristics. The objective of this research is to provide an effective, accessible, "green", and facile route for the decontamination of chemical warfare agents (CWAs, namely the blistering agent-mustard gas/sulfur mustard (HD)) from contaminated surfaces, by decomposition and entrapment of CWAs and their degradation products inside the hydrogel films generated "on-site". The decontamination of the notorious warfare agent HD was successfully achieved through a dual hydrolytic-photocatalytic degradation process. Subsequently, the post-decontamination residues were encapsulated within a hydrogel membrane film produced via an ionic crosslinking mechanism. Polyvinyl alcohol (PVA) and sodium alginate (ALG) are the primary constituents of the decontaminating formulations. These polymeric components were chosen for this application due to their cost-effectiveness, versatility, and their ability to form hydrogen bonds, facilitating hydrogel formation. In the presence of divalent metallic ions, ALG undergoes ionic crosslinking, resulting in rapid gelation. This facilitated prompt PVA-ALG film curing and allowed for immediate decontamination of targeted surfaces. Additionally, bentonite nanoclay, titanium nanoparticles, and a tetrasulfonated nickel phthalocyanine (NiPc) derivative were incorporated into the formulations to enhance absorption capacity, improve mechanical properties, and confer photocatalytic activity to the hydrogels obtained via Zn2+-mediated ionic crosslinking. The resulting hydrogels underwent characterization using a variety of analytical techniques, including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), viscometry, and mechanical analysis (shear, tensile, and compression tests), as well as swelling investigations, to establish the optimal formulations for CWA decontamination applications. The introduction of the fillers led to an increase in the maximum strain up to 0.14 MPa (maximum tensile resistance) and 0.39 MPa (maximum compressive stress). The UV-Vis characterization of the hydrogels allowed the determination of the band-gap value and absorption domain. A gas chromatography-mass spectrometry assay was employed to evaluate the decontamination efficacy for a chemical warfare agent (sulfur mustard-HD) and confirmed that the ionic crosslinked hydrogel films achieved decontamination efficiencies of up to 92.3%. Furthermore, the presence of the photocatalytic species can facilitate the degradation of up to 90% of the HD removed from the surface and entrapped inside the hydrogel matrix, which renders the post-decontamination residue significantly less dangerous.

Design of PEG-based hydrogels as soft ionic conductors

Conductive hydrogels have gained interest in biomedical applications and soft electronics. To tackle the challenge of ionic hydrogels falling short of desired mechanical properties in previous studies, our investigation aimed to understand the pivotal structural factors that impact the conductivity and mechanical behavior of polyethylene glycol (PEG)-based hydrogels with ionic conductivity. Polyether urethane diacrylamide (PEUDAm), a functionalized long-chain macromer based on PEG, was used to synthesize hydrogels with ionic conductivity conferred by incorporating ions into the liquid phase of hydrogel. The impact of salt concentration, water content, temperature, and gel formation on both mechanical properties and conductivity was characterized to establish parameters for tuning hydrogel properties. To further expand the range of conductivity available in these ionic hydrogels, 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) was incorporated as a single copolymer network or double network configuration. As expected, conductivity in these ionic gels was primarily driven by ion diffusivity and charge density, which was dependent on hydrogel network formation and swelling. Copolymer network structure had minimal effect on the conductivity which was primarily driven by counter-ion equilibrium; however, the mechanical properties and equilibrium swelling was strongly dependent on network structure. The structure-property relationships elucidated here enables the rationale design of this new double network hydrogel to achieve target properties for a broad range of applications.

Smart materials for flexible electronics and devices: hydrogel

In recent years, flexible conductive materials have attracted considerable attention for their potential use in flexible energy storage devices, touch panels, sensors, memristors, and other applications. The outstanding flexibility, electricity, and tunable mechanical properties of hydrogels make them ideal conductive materials for flexible electronic devices. Various synthetic strategies have been developed to produce conductive and environmentally friendly hydrogels for high-performance flexible electronics. In this review, we discuss the state-of-the-art applications of hydrogels in flexible electronics, such as energy storage, touch panels, memristor devices, and sensors like temperature, gas, humidity, chemical, strain, and textile sensors, and the latest synthesis methods of hydrogels. Describe the process of fabricating sensors as well. Finally, we discussed the challenges and future research avenues for flexible and portable electronic devices based on hydrogels.

Self-Healable and 4D Printable Hydrogel for Stretchable Electronics

Materials with high stretchability and conductivity are used to fabricate stretchable electronics. Self-healing capability and four-dimensional (4D) printability are becoming increasingly important for these materials to facilitate their recovery from damage and endow them with stimuli-response properties. However, it remains challenging to design a single material that combines these four strengths. Here, a dually crosslinked hydrogel is developed by combining a covalently crosslinked acrylic acid (AAC) network and Fe3+ ions through dynamic and reversible ionically crosslinked coordination. The remarkable electrical sensitivity (a gauge factor of 3.93 under a strain of 1500%), superior stretchability (a fracture strain up to 1700%), self-healing ability (a healing efficiency of 88% and 97% for the mechanical and electrical properties, respectively), and 4D printability of the hydrogel are demonstrated by constructing a strain sensor, a two-dimensional touch panel, and shape-morphing structures with water-responsive behavior. The hydrogel demonstrates vast potential for applications in stretchable electronics.

Sandwich hydrogel to realize cartilage-mimetic structures and performances from polyvinyl alcohol, chitosan and sodium hyaluronate

Developing artificial substitutes that mimic the structures and performances of natural cartilage is of great importance. However, it is challenging to integrate the high strength, excellent biocompatibility, low coefficient of friction, long-term wear resistance, outstanding swelling resistance, and osseointegration potential into one material. Herein, a sandwich hydrogel with cartilage-mimetic structures and performances was prepared to achieve this goal. The precursor hydrogel was obtained by freezing-thawing the mixture of poly vinyl alcohol, chitosan and deionized water three cycles, accompanied by soaking in sodium hyaluronate solution. The top of the precursor hydrogel was hydrophobically modified with lauroyl chloride and then loaded with lecithin, while the bottom was mineralized with hydroxyapatite. Due to the multiple linkages (crystalline domains, hydrogen bonds, and ionic interactions), the compressive stress was 71 MPa. Owing to the synergy of the hydrophobic modification and lecithin, the coefficient of friction was 0.01. Additionally, no wear trace was observed after 50,000 wear cycles. Remarkably, hydroxyapatite enabled the hydrogel osseointegration potential. The swelling ratio of the hydrogel was 0.06 g/g after soaking in simulated synovial fluid for 7 days. Since raw materials were non-toxic, the cell viability was 100 %. All of the above merits make it an ideal material for cartilage replacement.

Construction and Evaluation of Alginate Dialdehyde Grafted RGD Derivatives/Polyvinyl Alcohol/Cellulose Nanocrystals IPN Composite Hydrogels

To enhance the mechanical strength and cell adhesion of alginate hydrogel, making it satisfy the requirements of an ideal tissue engineering scaffold, the grafting of Arg-Gly-Asp (RGD) polypeptide sequence onto the alginate molecular chain was conducted by oxidation of sodium periodate and subsequent reduction amination of 2-methylpyridine borane complex (2-PBC) to synthesize alginate dialdehyde grafted RGD derivatives (ADA-RGD) with good cellular affinity. The interpenetrating network (IPN) composite hydrogels of alginate/polyvinyl alcohol/cellulose nanocrystals (ALG/PVA/CNCs) were fabricated through a physical mixture of ion cross-linking of sodium alginate (SA) with hydroxyapatite/D-glucono-δ-lactone (HAP/GDL), and physical cross-linking of polyvinyl alcohol (PVA) by a freezing/thawing method, using cellulose nanocrystals (CNCs) as the reinforcement agent. The effects of the addition of CNCs and different contents of PVA on the morphology, thermal stability, mechanical properties, swelling, biodegradability, and cell compatibility of the IPN composite hydrogels were investigated, and the effect of RGD grafting on the biological properties of the IPN composite hydrogels was also studied. The resultant IPN ALG/PVA/CNCs composite hydrogels exhibited good pore structure and regular 3D morphology, whose pore size and porosity could be regulated by adjusting PVA content and the addition of CNCs. By increasing the PVA content, the number of physical cross-linking points in PVA increased, resulting in greater stress support for the IPN composite hydrogels of ALG/PVA/CNCs and consequently improving their mechanical characteristics. The creation of the IPN ALG/PVA/CNCs composite hydrogels' physical cross-linking network through intramolecular or intermolecular hydrogen bonding led to improved thermal resistance and reduced swelling and biodegradation rate. Conversely, the ADA-RGD/PVA/CNCs IPN composite hydrogels exhibited a quicker degradation rate, attributed to the elimination of ADA-RGD by alkali. The results of the in vitro cytocompatibility showed that ALG/0.5PVA/0.3%CNCs and ADA-RGD/PVA/0.3%CNCs composite hydrogels showed better proliferative activity in comparison with other composite hydrogels, while ALG/PVA/0.3%CNCs and ADA-RGD/PVA/0.3%CNCs composite hydrogels displayed obvious proliferation effects, indicating that PVA, CNCs, and ADA-RGD with good biocompatibility were conducive to cell proliferation and differentiation for the IPN composite hydrogels.

Mechanical Properties of Alginate Hydrogels Cross-Linked with Multivalent Cations

Ionically, cross-linked alginate gels have a potential to be used in a wide range of biomedical, environmental and catalytic applications. The study deals with preparation of alginate hydrogels cross-linked with various cations and the analysis of their equilibrium swelling and mechanical properties. It is shown that the type of cations used in the cross-linking process affects the elastic moduli and the equilibrium degree of swelling of the gels. The experimental data in small-amplitude oscillatory tests are fitted with a model that involves two material parameters: the elastic modulus of a polymer network and a measure of its inhomogeneity. The influence of cations on these quantities is studied numerically. It is revealed that the dependence of the elastic modulus of ionically cross-linked alginate gels on their equilibrium degree of swelling differs from that predicted by the conventional theory for covalently cross-linked gels.

High-Strength Double-Network Conductive Hydrogels Based on Polyvinyl Alcohol and Polymerizable Deep Eutectic Solvent

Conductive hydrogels feature the flexibility of soft materials plus conductive properties providing functionality for effectively sticking to the epidermis and detecting human activity signals. Their stable electrical conductivity also effectively avoids the problem of uneven distribution of solid conductive fillers inside traditional conductive hydrogels. However, the simultaneous integration of high mechanical strength, stretchability, and transparency through a simple and green fabrication method remains a great challenge. Herein, a polymerizable deep eutectic solvent (PDES) composed of choline chloride and acrylic acid was added to a biocompatible PVA matrix. The double-network hydrogels were then simply prepared by thermal polymerization and one freeze-thaw method. The introduction of the PDES significantly improved the tensile properties (1.1 MPa), ionic conductivity (2.1 S/m), and optical transparency (90%) of the PVA hydrogels. When the gel sensor was fixed to human skin, real-time monitoring of a variety of human activities could be implemented with accuracy and durability. Such a simple preparation method performed by combining a deep eutectic solvent with traditional hydrogels offers a new avenue to construct multifunctional conductive hydrogel sensors with excellent performance.

A Liquid Metal Microdroplets Initialized Hemicellulose Composite for 3D Printing Anode Host in Zn-Ion Battery

Maintaining a steady affinity between gallium-based liquid metals (LM) and polymer binders, particularly under continuous mechanical deformation, such as extrusion-based 3D printing or plating/stripping of Zinc ion (Zn²⁺ ), is very challenging. Here, an LM-initialized polyacrylamide-hemicellulose/EGaIn microdroplets hydrogel is used as a multifunctional ink to 3D-print self-standing scaffolds and anode hosts for Zn-ion batteries. The LM microdroplets initiate acrylamide polymerization without additional initiators and cross-linkers, forming a double-covalent hydrogen-bonded network. The hydrogel acts as a framework for stress dissipation, enabling recovery from structural damage due to the cyclic plating/stripping of Zn²⁺ . The LM-microdroplet-initialized polymerization with hemicelluloses can facilitate the production of 3D printable inks for energy storage devices.

High stretchable and self-healing nanocellulose-poly(acrylic acid) composite hydrogels for sustainable CO2 shutoff

The injection of CO₂ into oil reservoirs to enhance oil recovery (EOR) has become a widely accepted and effective technical method, which, however, remains subject to the gas channeling caused by the reservoir fractures. Herein, this work developed a novel plugging gel combining excellent mechanical properties, fatigue resistance, elastic and self-healing properties for the CO₂ shutoff purpose. This gel consisting of grafted nanocellulose and polymer network was synthesized via a free-radical polymerization, and reinforced by using Fe³⁺ to cross-link the two networks. The as-prepared PAA-TOCNF-Fe³⁺ gel has a stress of 1.03 MPa and a high strain of 1491 %, and self-heals to its original 98 % in stress and 96 % in strain after rupture, respectively. The introduce of TOCNF/Fe³⁺ improves the excellent energy dissipation and self-healing via the synergy effect of dynamical coordination bonds and hydrogen bonds. Further, the PAA-TOCNF-Fe³⁺ gel is both flexible and high-strength in plugging the multi-round CO₂ injection, during which the CO₂ breakthrough pressure is above 9.9 MPa/m, the plugging efficiency exceeds 96 %, and the self-healing rate is larger than 90 %. Given that above, this gel shows a great potential to plug the high-pressure CO₂ flow, which could offer a new method for CO₂-EOR and carbon storage.

Ionic conductive hydroxypropyl methyl cellulose reinforced hydrogels with extreme stretchability, self-adhesion and anti-freezing ability for highly sensitive skin-like sensors

Ionically-conductive hydrogels are attracting increasing interest as skin-like sensors, however, the fabrication of ion-conductive hydrogels with excellent mechanical properties, high conductivity, self-adhesion and anti-freezing ability for high-performance sensors remains a challenge. Herein, a highly ion-conductive hydrogel is prepared by introducing LiCl into polyacrylamide/hydroxypropyl methyl cellulose (PAM/HPMC) composite hydrogel. The introduction of LiCl simultaneously endows the PAM/HPMC/LiCl hydrogel with outstanding stretchability (1453 %), high tensile strength (135 kPa), skin-like elasticity (9.18 kPa), high conductivity (7.85 S/m), good adhesiveness and wide operating temperature range. Impressively, this ion-conductive hydrogel can be utilized in skin-like sensor, which achieves high strain sensitivity (GF = 11.19) with wide sensing ranges (up to 600 %), and excellent endurance over 250 consecutive stretching. As a result, the wearable sensor assembled from the hydrogels can be used to detect complex human activities with high stability even at -40 °C. This work promotes the development of ion-conductive hydrogels with broad operating temperature in advanced sensory platform.

Nanocomposite conductive tough hydrogel based on metal coordination reinforced covalent Pluronic F-127 micelle network for human motion sensing

The design of conductive hydrogels integrating anti-fatigue, high sensitivity, strong mechanical property and good sterilization performance remains a challenge. We innovatively introduced metal coordination in covalently crosslinked Pluronic F-127 micelle network and synthesized nanocomposite conductive tough hydrogel through the combination of covalent crosslinking, metal coordination and silver nanowire reinforcement. Compared with pure diacylated PF127 hydrogel (PF127), the tensile strength of PF-AA-AM-Al³⁺/Ag0.25 hydrogel reaching 1.4 MPa was about 10 times than that of PF127. The toughness of PF-AA-AM-Al³⁺/Ag0.25 reaches 1.88 MJ/m³. Compared with PF-AA-AM-Al³⁺, the introduction of silver nanowires increased the fatigue life of PF-AA-AM-Al³⁺/Ag0.25 by 200% (31837 cycles), 170% (12804 cycles) and 1022% (511 cycles) under 100%, 120% and 150% ultimate tensile strains, respectively. Besides, the PF-AA-AM-Al³⁺/Ag0.25 showed strain sensitivity to small deformation (Gauge factor = 2.42) in wearable tests on hands and knees. In addition, the PF-AA-AM-Al³⁺/Ag0.25 had good cytocompatibility and antibacterial performance that bacteria killing ratio of 98% to S. aureus and 99% to E. coli. Finally, a viscoelastic numerical constitutive model was established based on finite element method to study the damage failure history of the material. Comparative analysis showed that local stress concentration was the main factor leading to the failure of hydrogel.

Conductive Gels: Properties and Applications of Nanoelectronics

Conductive gels are a special class of soft materials. They harness the 3D micro/nanostructures of gels with the electrical and optical properties of semiconductors, producing excellent novel attributes, like the formation of an intricate network of conducting micro/nanostructures that facilitates the easy movement of charge carriers. Conductive gels encompass interesting properties, like adhesion, porosity, swelling, and good mechanical properties compared to those of bulk conducting polymers. The porous structure of the gels allows the easy diffusion of ions and molecules and the swelling nature provides an effective interface between molecular chains and solution phases, whereas good mechanical properties enable their practical applications. Due to these excellent assets, conductive gels are promising candidates for applications like energy conversion and storage, sensors, medical and biodevices, actuators, superhydrophobic coatings, etc. Conductive gels offer promising applications, e.g., as soft sensors, energy storage, and wearable electronics. Hydrogels with ionic species have some potential in this area. However, they suffer from dehydration due to evaporation when exposed to the air which limits their applications and lifespan. In addition to conductive polymers and organic charge transfer complexes, there is another class of organic matter called "conductive gels" that are used in the organic nanoelectronics industry. The main features of this family of organic materials include controllable photoluminescence, use in photon upconversion technology, and storage of optical energy and its conversion into electricity. Various parameters change the electronic and optical behaviors of these materials, which can be changed by controlling some of the structural and chemical parameters of conductive gels, their electronic and optical behaviors depending on the applications. If the conjugated molecules with π bonds come together spontaneously, in a relative order, to form non-covalent bonds, they form a gel-like structure that has photoluminescence properties. The reason for this is the possibility of excitation of highest occupied molecular orbital level electrons of these molecules due to the collision of landing photons and their transfer to the lowest unoccupied molecular orbital level. This property can be used in various nanoelectronic applications such as field-effect organic transistors, organic solar cells, and sensors to detect explosives. In this paper, the general introduction of conductive or conjugated gels with π bonds is discussed and some of the physical issues surrounding electron excitation due to incident radiation and the mobility of charge carriers, the position, and role of conductive gels in each of these applications are discussed.

Biocompatible Conductive Hydrogels: Applications in the Field of Biomedicine

The impact of COVID-19 has rendered medical technology an important factor to maintain social stability and economic increase, where biomedicine has experienced rapid development and played a crucial part in fighting off the pandemic. Conductive hydrogels (CHs) are three-dimensional (3D) structured gels with excellent electrical conductivity and biocompatibility, which are very suitable for biomedical applications. CHs can mimic innate tissue's physical, chemical, and biological properties, which allows them to provide environmental conditions and structural stability for cell growth and serve as efficient delivery substrates for bioactive molecules. The customizability of CHs also allows additional functionality to be designed for different requirements in biomedical applications. This review introduces the basic functional characteristics and materials for preparing CHs and elaborates on their synthetic techniques. The development and applications of CHs in the field of biomedicine are highlighted, including regenerative medicine, artificial organs, biosensors, drug delivery systems, and some other application scenarios. Finally, this review discusses the future applications of CHs in the field of biomedicine. In summary, the current design and development of CHs extend their prospects for functioning as an intelligent and complex system in diverse biomedical applications.

β-Cyclodextrin-Based Ultrahigh Stretchable, Flexible, Electro- and Pressure-Responsive, Adhesive, Transparent Hydrogel as Motion Sensor

In the present work, a multiple-stimuli-responsive hydrogel has been synthesized via polymerization of acrylamide (AAm) and N-hydroxy methyl acrylamide (HMAm) on β-cyclodextrin (β-CD). The synthesized hydrogel β-CD-g-(pAAm/pHMAm) exhibited various striking features like ultrahigh stretchability (>6000%), flexibility, stab resistivity, self-recoverability, electroresponsiveness, pressure-responsiveness, adhesiveness, and high transparency (>90%). Besides, the hydrogel has demonstrated enhanced biocompatibility, UV resistance, and thermoresponsive shape memory behaviors. On the basis of these attractive characteristics of the hydrogel, a flexible pressure sensor for the real-time monitoring of human motion with superior biocompatibility and transparency was fabricated. Moreover, due to the nanofibrillar surface morphology of the β-CD-g-(pAAm/pHMAm) hydrogel, the sensor based on the gel exhibited high sensitivity (0.053 kPa^-1 for 0-3.3 kPa). The flexible sensor demonstrates very fast response time (130 ms-210 ms) with adequate stability (5000 cycles). Interestingly, the sensor can rapidly sense both robust (index finger and wrist) motions as well as tiny (swallowing and phonation) physiological actions. In addition, this adhesive hydrogel patch also acts as a potential carrier for the sustained topical release of (∼80.8% in 48 h) the antibiotic drug gentamicin sulfate.

Quality assessment of lemon (Citrus aurantifolia, swingle) coated with self-healed multilayer films based on chitosan/carboxymethyl cellulose under cold storage conditions

The polyelectrolyte multilayer self-healing coating film of chitosan and carboxymethyl cellulose (PEM-SH) tended to maintain high sensory quality and control physiological and pathological decay of lemon fruits under cold storage. The PEM-SH film was characterized by ATR-IR, XRD, X-ray photoelectron spectroscopy, SEM analysis, swelling ratio, self-healing, and mechanical characteristics. The 3-layered film (3L) exhibited the optimum barrier properties; WVP: 3.32 ± 0.06 g. mm. k Pa-1.h-1.m-2 and GTR: 0.256 ± 0.032 cc.M-2.day-1. The moisture sorption isotherm data were fitted with BET, GAB, and Peleg models and three models showed applicability. The coated fruits exhibit superior features of fruit quality such as reduced weight loss %, respiration rate, and decay symptoms appearance. The 3L-coated fruit showed the lower pectinase enzyme activity (0.689 Ug-1 FW) up to 60 days. As well as, increased total soluble solids, keeping vitamin C of loss and decreasing percentage acidity of juice up to 60 days.

Starch as a reinforcement agent for poly(ionic liquid) hydrogels from deep eutectic solvent via frontal polymerization

For the first time, conductive starch/poly(ionic liquid) hydrogels from a polymerizable deep eutectic solvent (DES) by frontal polymerization (FP) were reported. The solubility and dispersibility for starch granules in the polymerizable DES was investigated. The effects of starch content on FP behaviors, mechanical properties and electrical conductivity of composite hydrogels were studied. Results showed that starch could be partially dissolved and dispersed in the DES. Comparing with the pure poly(ionic liquid) hydrogel from DES (the tensile strength was 41 K Pa), the tensile strength of composite hydrogel could increased by 3.07 times and reached 126 K Pa. When the fixed strain was 80 %, its compressive strength could increase by 6 times and reaches 16.8 MPa. The main reason was that there was a strong interfacial interaction between starch and the polymer hydrogel network. The starch/poly(ionic liquid) composite hydrogels also had good electrical conductivity. Absorption of water could increase the conductivity of the composite hydrogel significantly.

Synergy coordination of cellulose-based dialdehyde and carboxyl with Fe3+ recoverable conductive self-healing hydrogel for sensor

A novel dual ionic network cellulose-based composite conductive self-healing hydrogel was fabricated with high elongation, rapid recoverability, high conductive sensitivity, self-healing ability and good biocompatibility. The hydrogel was constructed by the synergistic complexations of new-fashioned bidentate aldehyde groups on dialdehyde cellulose nanofibers (DACNFs) and carboxyl groups of acrylic acid (AA) with Fe³⁺. The elongation (~1300%) of the hydrogel containing 1 wt% DACNFs was approximate 13-fold of the pure PAA hydrogel and can recover to original state within 2 min after 80% compression. The self-healing efficiency increased with the addition of DACNFs in the dual ionic network cellulose-based composite conductive self-healing hydrogel. The hydrogel configured for a wearable test and showed high stretching sensitivity with a gauge factor of 13.82 at strain within 1.6%. The gauge factor (GF) decrease with the incremental strain within 20%. GF were 0.696 between 20% and 300% strain, 0.837 within 300% and 500%. Meanwhile, the current had a good linear relationship with the bending angles of hydrogels and pressure on hydrogels, which may provide a great potential in monitor both minor variations and large movements.

Assessing Green Methods for Pectin Extraction from Waste Orange Peels

In this work, we assess three different methods for the extraction of pectin from waste orange peels, using water as extracting solvent. “Hot-water”, Rapid Solid Liquid Dynamic (RSLD) and microwave-assisted extractions have been compared and evaluated in terms of amount and quality of extracted pectin, as well as embodied energy. This analysis provides useful guidelines for pectin production from food waste according to green procedures, enabling the identification of acidic “hot-water” as the most sustainable extraction route.

Dynamic cross-linking of an alginate-acrylamide tough hydrogel system: time-resolved in situ mapping of gel self-assembly

Hydrogels are a popular class of biomaterial that are used in a number of commercial applications (e.g.; contact lenses, drug delivery, and prophylactics). Alginate-based tough hydrogel systems, interpenetrated with acrylamide, reportedly form both ionic and covalent cross-links, giving rise to their remarkable mechanical properties. In this work, we explore the nature, onset and extent of such hybrid bonding interactions between the complementary networks in a model double-network alginate-acrylamide system, using a host of characterisation techniques (e.g.; FTIR, Raman, UV-vis, and fluorescence spectroscopies), in a time-resolved manner. Further, due to the similarity of bonding effects across many such complementary, interpenetrating hydrogel networks, the broad bonding interactions and mechanisms observed during gelation in this model system, are thought to be commonly replicated across alginate-based and broader double-network hydrogels, where both physical and chemical bonding effects are present. Analytical techniques followed real-time bond formation, environmental changes and re-organisational processes that occurred. Experiments broadly identified two phases of reaction; phase I where covalent interaction and physical entanglements predominate, and; phase II where ionic cross-linking effects are dominant. Contrary to past reports, ionic cross-linking occurred more favourably via mannuronate blocks of the alginate chain, initially. Evolution of such bonding interactions was also correlated with the developing tensile and compressive properties. These structure-property findings provide mechanistic insights and future synthetic intervention routes to manipulate the chemo-physico-mechanical properties of dynamically-forming tough hydrogel structures according to need (i.e.; durability, biocompatibility, adhesion, etc.), allowing expansion to a broader range of more physically and/or environmentally demanding biomaterials applications.

Tannic Acid-Silver Dual Catalysis Induced Rapid Polymerization of Conductive Hydrogel Sensors with Excellent Stretchability, Self-Adhesion, and Strain-Sensitivity Properties

The application of conductive hydrogels in intelligent biomimetic electronics is a hot topic in recent years, but it is still a great challenge to develop the conductive hydrogels through a rapid fabrication process at ambient temperature. In this work, a versatile poly(acrylamide) @cellulose nanocrystal/tannic acid-silver nanocomposite (NC) hydrogel integrated with excellent stretchability, repeatable self-adhesion, high strain sensitivity, and antibacterial property, was synthesized via radical polymerization within 30 s at ambient temperature. Notably, this rapid polymerization was realized through a tannic acid-silver (TA-Ag) mediated dynamic catalysis system that was capable of activating ammonium persulfate and then initiated the free-radical polymerization of the acrylamide monomer. Benefiting from the incorporation of TA-Ag metal ion nanocomplexes and cellulose nanocrystals, which acted as dynamic connecting bridges by hydrogen bonds to efficiently dissipate energy, the obtained NC hydrogels exhibited prominent tensile strain (up to 4000%), flexibility, self-recovery, and antifatigue properties. In addition, the hydrogels showed repeatable adhesiveness to different substrates (e.g., glass, wood, bone, metal, and skin) and significant antibacterial properties, which were merits for the hydrogels to be assembled into a flexible epidermal sensor for long-term human-machine interfacial contact without concerns about the use of external adhesive tapes and bacterial breeding. Moreover, the remarkable conductivity (σ ∼ 5.6 ms cm^-1) and strain sensitivity (gauge factor = 1.02) allowed the flexible epidermal sensors to monitor various human motions in real time, including huge movement of deformations (e.g., wrist, elbow, neck, shoulder) and subtle motions. It is envisioned that this work would provide a promising strategy for the rapid preparation of conductive hydrogels in the application of flexible electronic skin, biomedical devices, and soft robotics.

Full Poly(ethylene glycol) Hydrogels with High Ductility and Self-Recoverability

Energy dissipation is a common mechanism to improve the ductility of polymeric hydrogels. However, for poly(ethylene glycol) (PEG) hydrogels, it is not easy to dissipate energy, as polymer chains are dispersed in water without strong interchain interactions or decent entanglement. The brittleness limits the real applications of PEG hydrogels, although they are promising candidates in biomedical fields, as PEG has been approved by the U.S. Food and Drug Administration. Herein, we chemically introduced a center for energy dissipation in the PEG hydrogel system. Amphiphilic segmented PEG derivatives were designed through the melt polycondensation of triethylene glycol (PEG₁₅₀) and high molecular weight PEG in the presence of succinic acid and mercaptosuccinic acid as dicarboxylic acids. Full PEG hydrogels with elastic nanospheres as giant cross-linkers were facilely prepared by the self-assembly of esterified PEG₁₅₀ segments and the oxidation of mercapto groups. The resultant full PEG hydrogels can dissipate energy by the deformation of elastic nanospheres with outstanding ductility and self-recoverability while maintaining the excellent biocompatibility owing to their full PEG components. This work provides an original strategy to fabricate full PEG hydrogels with high ductility and self-recoverability, potentially applicable in biomedical fields.

Alkaline Double-Network Hydrogels with High Conductivities, Superior Mechanical Performances, and Antifreezing Properties for Solid-State Zinc-Air Batteries

For the development of advanced flexible and wearable electronic devices, functional electrolytes with excellent conductivity, temperature tolerance, and desirable mechanical properties need to be engineered. Herein, an alkaline double-network hydrogel with high conductivity and superior mechanical and antifreezing properties is designed and promisingly utilized as the flexible electrolyte in all-solid-state zinc-air batteries. The conductive hydrogel is comprised of covalently cross-linked polyelectrolyte poly(2-acrylamido-2-methylpropanesulfonic acid potassium salt) (PAMPS-K) and interpenetrating methyl cellulose (MC) in the presence of concentrated alkaline solutions. The covalently cross-linked PAMPS-K skeleton and interpenetrating MC chains endow the hydrogel with good mechanical strength, toughness, an extremely rapid self-recovery capability, and an outstanding antifatigue property. Gratifyingly, the entrapment of a concentrated alkaline solution in the hydrogel matrix yields an extremely high ionic conductivity (105 mS cm^-1 at 25 °C) and an excellent antifreezing capacity. The hydrogel retains comparable conductivity and eligible strength to withstand various mechanical deformations at -20 °C. The all-solid-state zinc-air batteries using PAMPS-K/MC hydrogels as flexible alkaline electrolytes exhibit comparable values of specific capacity (764.7 mAh g^-1), energy capacity (850.2 mWh g^-1), cycling stability, and mechanical flexibility. The batteries still possess competitive electrochemical performances even when the operating temperature drops to -20 °C.

Double-Hydrophobic-Coating through Quenching for Hydrogels with Strong Resistance to Both Drying and Swelling

In recent years, various hydrogels with a wide range of functionalities have been developed. However, owing to the two major drawbacks of hydrogels-air-drying and water-swelling-hydrogels developed thus far have yet to achieve most of their potential applications. Herein, a bioinspired, facile, and versatile method for fabricating hydrogels with high stability in both air and water is reported. This method includes the creation of a bioinspired homogeneous fusion layer of a hydrophobic polymer and oil in the outermost surface layer of the hydrogel via a double-hydrophobic-coating produced through quenching. As a proof-of-concept, this method is applied to a polyacrylamide hydrogel without compromising its mechanical properties. The coated hydrogel exhibits strong resistance to both drying in air and swelling in multiple aqueous environments. Furthermore, the versatility of this method is demonstrated using different types of hydrogels and oils. Because this method is easy to apply and is not dependent on hydrogel surface chemistry, it can significantly broaden the scope of next-generation hydrogels for real-world applications in both wet and dry environments.