Silica-Supported Ionic Liquids for Heat-Powered Sorption Desalination

Novel and highly efficient transformation of carbon dioxide into 2-oxazolidinones over Al-MCM-41 mesoporous-supported ionic liquids

A type of Al-MCM-41 supported dual imidazolium ionic liquids were constructed and efficiently used as catalysts for the synthesis of 2-oxazolidinones from epoxides, amines, and CO2. The influence of the different catalysts and reaction parameters on the catalytic behaviours was investigated. Al-MCM-41@ILTiCl5 was identified as the most excellent catalyst because it could efficiently promote the three-component cycloaddition of CO2, epoxide, and amines to form the corresponding 2-oxazolidinones in high to excellent yields (84∼96%) with excellent selectivities (98∼99.7%). In addition, the recovery and reuse performances of Al-MCM-41@ILTiCl5 were examined. The catalyst could be recovered by simple filtration and reused six times without a change in the catalytic activity. Green reaction conditions, operational simplicity, feasibility, and sustainability of the functionalized catalyst are the main highlights of the present protocol.

Effects of mesylate-/tartrate-based ionic liquids-water mixtures on the phase transition behaviors and stability of corn starch: A comparative study

As one of the most important biopolymers, starch has been applied to replace petroleum-derived polymers for "green" materials. Discovery of novel solvents and understanding of the solvent effects are critical challenges for the destruction of strong hydrogen bonds of starch molecules for manufacturing bio-based materials. Herein, two ionic liquids (ILs), 1-ethyl-3-methyl-imidazolium mesylate ([Emim][MS]) and 1-ethyl-3-methyl-imidazolium tartrate ([Emim][Tar]), were explored as novel solvents for starch. Their effects on phase transition behaviors, microstructure, hydrogen-bond interaction, crystalline structure, micromorphology and thermal stability of corn starch were compared systematically. With the IL/H₂O ratio increasing, the starch/IL/H₂O mixtures underwent endothermic, exothermic/endothermic and exothermic processes, sequentially. However, the starch properties were very different in two ILs-water systems, which were closely related to the solvent composition and IL structure. These differences were further explained by the interactions among starch, water and the two ILs on the basis of the quantum chemical calculations. It was found that [Emim][MS] had a stronger interaction with water than starch, whereas [Emim][Tar] preferred to bind with starch. This study not only provided experimental supports for understanding the starch behaviors in novel "green" solvents, but also laid the theoretical foundation for starch modification and industrial applications of starch-based materials in more appropriate solvents.

Butyl-Methyl-Pyridinium Tetrafluoroborate Confined in Mesoporous Silica Xerogels: Thermal Behaviour and Matrix-Template Interaction

Organic-inorganic silica composites have been prepared via acid catalyzed sol-gel route using tetramethoxysilan (TMOS) and methyl-trimethoxysilane (MTMS) as silica precursors and n-butyl-3-methylpyridinium tetrafluoroborate ([bmPy][BF₄]) as co-solvent and pore template, by varying the content of the ionic liquid (IL). Morphology of the xerogels prepared using the ionic liquid templating agent were investigated using scanning electron microscopy and small angle neutron scattering (SANS). Thermal analysis has been used in order to evaluate the thermal and structural stability of the materials, in both nitrogen and synthetic air atmosphere. In nitrogen atmosphere, the IL decomposition took place in one step starting above 150 °C and completed in the 150–460 °C temperature interval. In synthetic air atmosphere, the IL decomposition produced two-step mass loss, mainly in the 170–430 °C temperature interval. The decomposition mechanism of the IL inside the silica matrix was studied by mass spectrometric evolved gas analysis (MSEGA). The measurements showed that the degradation of the IL’s longer side chain (butyl) starts at low temperature (above 150 °C) through a C-N bond cleavage, initiated by the nucleophilic attack of a fluorine ion.

Ionogels at the Water-Energy Nexus for Desalination Powered by Ultralow-Grade Heat

Industrial processes emit enormous amounts of waste heat below 40 °C into the environment as it is cannot be used in other processes. Adsorption desalination can be driven by low-grade heat but has never been proven at temperatures below 40 °C as current adsorption materials require heat sources of 50-150 °C. Here, we present the first experimental study on adsorption desalination using a novel class of ionogel adsorption materials, which can be regenerated at 25 °C or a driving temperature difference of 5 °C. This outstanding property contrasts with the benchmarking silica gel, which requires heat sources of at least 50 °C. Ionogels are solid-state ionic materials retaining the sorption properties of the constituent ionic liquid. Thermodynamic vapor-liquid equilibrium data of water sorption on commercial ionic liquids reveal 1-ethyl-3-methylimidazolium acetate as the best fluid for this specific application. A full experimental characterization of the material is performed from imaging at the nanoscale to testing on a real adsorption desalinator. At 25 °C, the material achieves a specific daily water production of 6.7 kg_water/(kg_ionogel d), increasing to 17.5 kg_water/(kg_ionogeld) at 45 °C, outperforming silica gel by a factor of 2.