Alternating Current Techniques for a Better Understanding of Photoelectrocatalysts

Hematite decorated with Ni metal-organic framework for sensitive photoelectrochemical sensing of glucose

Photoelectrochemical (PEC) sensor is a simple and practical detection device with the advantages of low background signals and high sensitivity. In this work, a simple two-step post-calcination method was adopted to prepare α-Fe2O3 photoelectrode, followed by a Ni metal-organic framework (Ni-MOF) was deposited via a one-step solvothermal process, to obtain Ni-MOF/α-Fe2O3 photoelectrode, which was finally used for glucose sensing. The linear sweep voltammetry for glucose oxidation over Ni-MOF/α-Fe2O3 displayed a 0.24 V negative shift of initial potential and a significant photocurrent increase compared to bare α-Fe2O3, suggesting an accelerated glucose oxidation kinetics caused by Ni-MOF. (Photo)electrochemical characterizations revealed Ni-MOF could not only promote the charge separation but also provide active sites for glucose oxidation. As a result, Ni-MOF/α-Fe2O3 demonstrated a superior sensing performance toward glucose in the concentration range of 0.002-1.6 mM at 0 V vs. SCE. Specially, when the concentration of glucose was 1 mM, the photocurrent of Ni-MOF/α-Fe2O3 was increased by 18-fold compared to α-Fe2O3. The Ni-MOF/α-Fe2O3 sensors also offered good selectivity, excellent reproducibility and remarkable long-term stability. Especially, the present Ni-MOF/α-Fe2O3 based PEC method exhibited comparable accuracy to high performance liquid chromatography (HPLC) in real sample analysis, such as bread and glucose solution. The results of this work would provide useful information for developing new semiconductor PEC glucose sensors.

Carboxyl-Group-Bearing Metal Corroles of Cobalt, Manganese and Copper for Electrocatalytic Hydrogen Evolution

5,15-bis(perfluorophenyl)-10-(4-carboxyphenyl) corrole and its Co(III), Mn(III), and Cu(III) corrole complexes were synthesized. The electrocatalytic hydrogen evolution reaction (HER) of these metal corrole complexes was investigated using different proton sources (AcOH, trifluoroacetic acid, and TsOH) in an organic dimethylformamide solvent. The electrocatalytic HER may proceed through EECC, EECEC, or EEECEC pathways (where E represents electron transfer and C represents proton binding) depending on the acidity and concentration of the proton source used. The Co corrole complex exhibits remarkable hydrogen production performance, achieving a turnover frequency of 201 s-1 and a catalytic efficiency of 1.00. The examined metal corrole complexes also exhibit good HER activity in aqueous solution, with their catalytic activity following an order of 1-Co>1-Cu>1-Mn in both organic and aqueous phases.

Particle-Based Photoelectrodes for PEC Water Splitting: Concepts and Perspectives

This comprehensive review delves into the intricacies of the photoelectrochemical (PEC) water splitting process, specifically focusing on the design, fabrication, and optimization of particle-based photoelectrodes for efficient green hydrogen production. These photoelectrodes, composed of semiconductor materials, potentially harness light energy and generate charge carriers, driving water oxidation and reduction reactions. The versatility of particle-based photoelectrodes as a platform for investigating and enhancing various semiconductor candidates is explored, particularly the emerging complex oxides with compelling charge transfer properties. However, the challenges presented by many factors influencing the performance and stability of these photoelectrodes, including particle size, shape, composition, morphology, surface modification, and electrode configuration, are highlighted. The review introduces the fundamental principles of semiconductor photoelectrodes for PEC water splitting, presents an exhaustive overview of different synthesis methods for semiconductor powders and their assembly into photoelectrodes, and discusses recent advances and challenges in photoelectrode material development. It concludes by offering promising strategies for improving photoelectrode performance and stability, such as the adoption of novel architectures and heterojunctions.

Barium-induced lattice expansion of Ni(OH)2: enhancing catalytic urea oxidation activity for energy-saving H2 production

Constructing an environmentally friendly and efficient electrocatalyst holds important and profound significance for energy-efficient hydrogen production. Replacing the oxygen evolution reaction with a lower potential urea oxidation reaction (UOR) may save energy in water electrolysis to produce hydrogen. The UOR is characterized by its high energy barrier, which results in slow reaction kinetics. In this study, we introduced Ba(OH)2 into Ni(OH)2 to form uniform nanosheets. Due to the introduction of Ba2+, the lattice expansion of Ni(OH)2 was triggered, leading to significant improvement in UOR activity. The catalyst achieved a current density of 100 mA cm-2 at only 1.316 V and exhibited remarkable stability over time. Density functional theory (DFT) calculations demonstrate that the Ba-Ni(OH)2 site significantly reduces the energy barrier for urea adsorption, intermediate steps, and desorption. This work provides a novel and environmentally friendly strategy for constructing energy-efficient and highly efficient catalysts through the doping of alkaline earth metals.

Overcoming the Potential Window-Limited Functional Group Compatibility by Alternating Current Electrolysis

The functional group compatibility of an electrosynthetic method is typically limited by its potential reaction window. Here, we report that alternating current (AC) electrolysis can overcome such potential window-limited functional group compatibility. Using alkene heterodifunctionalization as a model system, we design and demonstrate a series of AC-driven reactions that add two functional groups sequentially and separately under the cathodic and anodic pulses, including chloro- and bromotrilfuoromethylation as well as chlorosulfonylation. We discovered that the oscillating redox environment during AC electrolysis allows the regeneration of the redox-active functional groups after their oxidation or reduction in the preceding step. As a result, even though redox labile functional groups such as pyrrole, quinone, and aryl thioether fall in the reaction potential window, they are tolerated under AC electrolysis conditions, leading to synthetically useful yields. The cyclic voltammetric study has confirmed that the product yield is limited by the extent of starting material regeneration during the redox cycling. Our findings open a new avenue for improving functional group compatibility in electrosynthesis and show the possibility of predicting the product yield under AC electrolysis from voltammogram features.

Intensity modulated photocurrent spectroscopy to investigate hidden kinetics at hybrid perovskite–electrolyte interface

The numerous assorted accounts of the fundamental questions of ion migration in hybrid perovskites are making the picture further intricate. The review of photo-induced ion migration using small perturbation frequency domain techniques other than impedance spectroscopy is more crucial now. Herein, we probe into this by investigating perovskite–electrolyte (Pe–E) and polymer-aqueous electrolyte (Po–aqE) interface using intensity modulated photocurrent spectroscopy (IMPS) in addition to photoelectrochemical impedance spectroscopy (PEIS). We reported that the electronic-ionic interaction in hybrid perovskites including the low-frequency ion/charge transfer and recombination kinetics at the interface leads to the spiral feature in IMPS Nyquist plot of perovskite-based devices. This spiral trajectory for the perovskite-electrolyte interface depicts three distinct ion kinetics going on at the different time scales which can be more easily unveiled by IMPS rather than PEIS. Hence, IMPS is a promising alternative to PEIS. We used Peter’s method of interpretation of IMPS plot in photoelectrochemistry to estimate charge transfer efficiency \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({Q}_{ste})$$\end{document}(Qste) from the Rate Constant Model. The \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Q}_{ste}$$\end{document}Qste at low-frequency for Pe–E interface exceeds unity due to ion migration induced modified potential across the perovskite active layer. Hence, ion migration and mixed electronic-ionic conductivity of hybrid perovskites are responsible for the extraordinary properties of this material.