Interpenetrating collagen-fibrin composite matrices with varying protein contents and ratios

Liver dECM-Gelatin Composite Bioink for Precise 3D Printing of Highly Functional Liver Tissues

In recent studies, liver decellularized extracellular matrix (dECM)-based bioinks have gained significant attention for their excellent compatibility with hepatocytes. However, their low printability limits the fabrication of highly functional liver tissue. In this study, a new liver dECM-gelatin composite bioink (dECM gBioink) was developed to overcome this limitation. The dECM gBioink was prepared by incorporating a viscous gelatin mixture into the liver dECM material. The novel dECM gBioink showed 2.44 and 10.71 times higher bioprinting resolution and compressive modulus, respectively, than a traditional dECM bioink. In addition, the new bioink enabled stable stacking with 20 or more layers, whereas a structure printed with the traditional dECM bioink collapsed. Moreover, the proposed dECM gBioink exhibited excellent hepatocyte and endothelial cell compatibility. At last, the liver lobule mimetic structure was successfully fabricated with a precisely patterned endothelial cell cord-like pattern and primary hepatocytes using the dECM gBioink. The fabricated lobule structure exhibited excellent hepatic functionalities and dose-dependent responses to hepatotoxic drugs. These results demonstrated that the gelatin mixture can significantly improve the printability and mechanical properties of the liver dECM materials while maintaining good cytocompatibility. This novel liver dECM gBioink with enhanced 3D printability and resolution can be used as an advanced tool for engineering highly functional liver tissues.

A bone-on-a-chip collagen hydrogel-based model using pre-differentiated adipose-derived stem cells for personalized bone tissue engineering

Mesenchymal stem cells have contributed to the continuous progress of tissue engineering and regenerative medicine. Adipose-derived stem cells (ADSC) possess many advantages compared to other origins including easy tissue harvesting, self-renewal potential, and fast population doubling time. As multipotent cells, they can differentiate into osteoblastic cell linages. In vitro bone models are needed to carry out an initial safety assessment in the study of novel bone regeneration therapies. We hypothesized that 3D bone-on-a-chip models containing ADSC could closely recreate the physiological bone microenvironment and promote differentiation. They represent an intermedium step between traditional 2D-in vitro and in vivo experiments facilitating the screening of therapeutic molecules while saving resources. Herein, we have differentiated ADSC for 7 and 14 days and used them to fabricate in vitro bone models by embedding the pre-differentiated cells in a 3D collagen matrix placed in a microfluidic chip. Osteogenic markers such as alkaline phosphatase activity, calcium mineralization, changes on cell morphology, and expression of specific proteins (bone sialoprotein 2, dentin matrix acidic phosphoprotein-1, and osteocalcin) were evaluated to determine cell differentiation potential and evolution. This is the first miniaturized 3D-in vitro bone model created from pre-differentiated ADSC embedded in a hydrogel collagen matrix which could be used for personalized bone tissue engineering.

pH and Thrombin Concentration Are Decisive in Synthesizing Stiff, Stable, and Open-Porous Fibrin-Collagen Hydrogel Blends without Chemical Cross-Linker

Fibrin-collagen hydrogel blends exhibit high potential for tissue engineering applications. However, it is still unclear whether the underlying cross-linking mechanisms are of chemical or physical nature. It is here hypothesized that chemical cross-linkers play a negligible role and that instead pH and thrombin concentration are decisive for synthetizing blends with high stiffness and hydrolytic stability. Different fibrin-collagen formulations (pure and with additional transglutaminase) are used and the blends' compaction rate, hydrolytic stability, compressive strength, and hydrogel microstructure are investigated. The effect of thrombin concentration on gel compaction is examined and the importance of pH control during synthesis observed. It is revealed that transglutaminase impairs gel stability and it is deduced that fibrin-collagen blends mainly cross-link by mechanical interactions due to physical fibril entanglement as opposed to covalent bonds from chemical cross-linking. High thrombin concentrations and basic pH during synthesis reduce gel compaction and enhance stiffness and long-term stability. Scanning electron microscopy reveals a highly interpenetrating fibrous network with unique, interconnected open-porous microstructures. Endothelial cells proliferate on the blends and form a confluent monolayer. This study reveals the underlying cross-linking mechanisms and presents enhanced fibrin-collagen blends with high stiffness, hydrolytic stability, and large, interconnected pores; findings that offer high potential for advanced tissue engineering applications.

Core-shell bioprinting of vascularized in vitro liver sinusoid models

In vitro liver models allow the investigation of the cell behavior in disease conditions or in response to changes in the microenvironment. A major challenge in liver tissue engineering is to mimic the tissue-level complexity: Besides the selection of suitable biomaterial(s) replacing the extracellular matrix (ECM) and cell sources, the three-dimensional (3D) microarchitecture defined by the fabrication method is a critical factor to achieve functional constructs. In this study, coaxial extrusion-based 3D bioprinting has been applied to develop a liver sinusoid-like model that consists of a core compartment containing pre-vascular structures and a shell compartment containing hepatocytes. The shell ink was composed of alginate and methylcellulose (algMC), dissolved in human fresh frozen plasma. The algMC blend conferred high printing fidelity and stability to the core-shell constructs and the plasma as biologically active component enhanced viability and supported cluster formation and biomarker expression of HepG2 embedded in the shell. For the core, a natural ECM-like ink based on angiogenesis-supporting collagen-fibrin (CF) matrices was developed; the addition of gelatin (G) enabled 3D printing in combination with the plasma-algMC shell ink. Human endothelial cells (HUVEC), laden in the CFG core ink together with human fibroblasts as supportive cells, formed a pre-vascular network in the core in the absence and presence of HepG2 in the shell. The cellular interactions occurring in the triple culture model enhanced the albumin secretion. In conclusion, core-shell bioprinting was shown to be a valuable tool to study cell-cell-interactions and to develop complex tissue-like models.

Advancements in Extracellular Matrix-Based Biomaterials and Biofabrication of 3D Organotypic Skin Models

Over the last decades, three-dimensional (3D) organotypic skin models have received enormous attention as alternative models to in vivo animal models and in vitro two-dimensional assays. To date, most organotypic skin models have an epidermal layer of keratinocytes and a dermal layer of fibroblasts embedded in an extracellular matrix (ECM)-based biomaterial. The ECM provides mechanical support and biochemical signals to the cells. Without advancements in ECM-based biomaterials and biofabrication technologies, it would have been impossible to create organotypic skin models that mimic native human skin. In this review, the use of ECM-based biomaterials in the reconstruction of skin models, as well as the study of complete ECM-based biomaterials, such as fibroblasts-derived ECM and decellularized ECM as a better biomaterial, will be highlighted. We also discuss the benefits and drawbacks of several biofabrication processes used in the fabrication of ECM-based biomaterials, such as conventional static culture, electrospinning, 3D bioprinting, and skin-on-a-chip. Advancements and future possibilities in modifying ECM-based biomaterials to recreate disease-like skin models will also be highlighted, given the importance of organotypic skin models in disease modeling. Overall, this review provides an overview of the present variety of ECM-based biomaterials and biofabrication technologies available. An enhanced organotypic skin model is expected to be produced in the near future by combining knowledge from previous experiences and current research.

Synthesis of Fibrin-Type I Collagen Biomaterials via an Acidic Gel

Fibrin-Type I collagen composite gels have been widely studied as biomaterials, in which both networks are usually formed simultaneously at a neutral pH. Here, we describe a new protocol in which mixed concentrated solutions of collagen and fibrinogen were first incubated at acidic pH to induce fibrinogen gel formation, followed by a pH change to neutral inducing collagen fiber formation. Thrombin was then added to form fibrin-collagen networks. Using this protocol, mixed gels containing 20 mg.mL⁻¹ fibrin and up to 10 mg.mL⁻¹ collagen could be prepared. Macroscopic observations evidenced that increasing the content of collagen increases the turbidity of the gels and decreases their shrinkage during the fibrinogen-to-fibrin conversion. The presence of collagen had a minor influence on the rheological properties of the gels. Electron microscopy allowed for observation of collagen fibers within the fibrin network. 2D cultures of C2C12 myoblasts on mixed gels revealed that the presence of collagen favors proliferation and local alignment of the cells. However, it interferes with cell differentiation and myotube formation, suggesting that further control of in-gel collagen self-assembly is required to elaborate fully functional biomaterials.

Adipogenic Differentiation Alters Properties of Vascularized Tissue-Engineered Skeletal Muscle

Advances in the engineering of comprehensive skeletal muscle models in vitro will improve drug screening platforms and can lead to better therapeutic approaches for the treatment of skeletal muscle injuries. To this end, a vascularized tissue-engineered skeletal muscle (TE-SkM) model that includes adipocytes was developed to better emulate the intramuscular adipose tissue that is observed in skeletal muscles of patients with diseases such as diabetes. Muscle precursor cells cultured with and without microvessels derived from adipose tissue (microvascular fragments) were used to generate TE-SkM constructs, with and without a microvasculature, respectively. TE-SkM constructs were treated with adipogenic induction media to induce varying levels of adipogenesis. With a delayed addition of induction media to allow for angiogenesis, a robust microvasculature in conjunction with an increased content of adipocytes was achieved. The augmentation of vascularized TE-SkM constructs with adipocytes caused a reduction in maturation (compaction), mechanical integrity (Young's modulus), and myotube and vessel alignment. An increase in basal glucose uptake was observed in both levels of adipogenic induction, and a diminished insulin-stimulated glucose uptake was associated with the higher level of adipogenic differentiation and the greater number of adipocytes.

Changes in the Molecular Characteristics of Bovine and Marine Collagen in the Presence of Proteolytic Enzymes as a Stage Used in Scaffold Formation

Biopolymers, in particular collagen and fibrinogen, are the leading materials for use in tissue engineering. When developing technology for scaffold formation, it is important to understand the properties of the source materials as well as the mechanisms that determine the formation of the scaffold structures. Both factors influence the properties of scaffolds to a great extent. Our present work aimed to identify the features of the molecular characteristics of collagens of different species origin and the changes they undergo during the enzymatic hydrolysis used for the process of scaffold formation. For this study, we used the methods of gel-penetrating chromatography, dynamic light scattering, reading IR spectra, and scanning electron microscopy. It was found that cod collagen (CC) and bovine collagen (BC) have different initial molecular weight parameters, and that, during hydrolysis, the majority of either type of protein is hydrolyzed by the proteolytic enzymes within the first minute. The differently sourced collagen samples were also hydrolyzed with the formation of two low molecular fractions: Mw ~ 10 kDa and ~20 kDa. In the case of CC, the microstructure of the final scaffolds contained denser, closely spaced fibrillar areas, while the BC-sourced scaffolds had narrow, short fibrils composed of unbound fibers of hydrolyzed collagen in their structure.

Cellulose Nanocrystal-Fibrin Nanocomposite Hydrogels Promoting Myotube Formation

Cellulose nanocrystals (CNCs) have been widely studied as fillers to form reinforced nanocomposites with a wide range of applications, including the biomedical field. Here, we evaluated the possibility to combine them with fibrinogen and obtain fibrin hydrogels with improved mechanical stability as potential cellular scaffolds. In diluted conditions at a neutral pH, it was evidenced that fibrinogen could adsorb on CNCs in a two-step process, favoring their alignment under flow. Composite hydrogels could be prepared from concentrated fibrinogen solutions and nanocrystals in amounts up to 0.3 wt %. CNCs induced a significant modification of the initial fibrin fibrillogenesis and final fibrin network structure, and storage moduli of all nanocomposites were larger than those of pure fibrin hydrogels. Moreover, optimal conditions were found that promoted muscle cell differentiation and formation of long myotubes. These results provide original insights into the interactions of CNCs with proteins with key physiological functions and offer new perspectives for the design of injectable fibrin-based formulations.

Engineering a macroporous fibrin-based sequential interpenetrating polymer network for dermal tissue engineering

The success of skin tissue engineering for deep wound healing relies predominantly on the design of innovative and effective biomaterials. This study reports the synthesis and characterization of a new type of naturally-derived and macroporous interpenetrating polymer network (IPN) for skin repair. These biomaterials consist of a biologically active fibrous fibrin network polymerized within a mechanically robust and macroporous construct made of polyethylene glycol and biodegradable serum albumin (PEGDM-co-SAM). First, mesoporous PEGDM-co-SAM hydrogels were synthesized and subjected to cryotreatment to introduce an interconnected macroporous network. Subsequently, fibrin precursors were incorporated within the cryotreated PEG-based network and then allowed to spontaneously polymerize and form a sequential IPN. Rheological measurements indicated that fibrin-based sequential IPN hydrogels exhibited improved and tunable mechanical properties when compared to fibrin hydrogels alone. In vitro data showed that human dermal fibroblasts adhere, infiltrate and proliferate within the IPN constructs, and were able to secrete endogenous extracellular matrix proteins, namely collagen I and fibronectin. Furthermore, a preclinical study in mice demonstrated that IPNs were stable over 1-month following subcutaneous implantation, induced a minimal host inflammatory response, and displayed a substantial cellular infiltration and tissue remodeling within the constructs. Collectively, these data suggest that macroporous and mechanically reinforced fibrin-based sequential IPN hydrogels are promising three-dimensional platforms for dermal tissue regeneration.

Diabetic Conditions Confer Metabolic and Structural Modifications to Tissue-Engineered Skeletal Muscle

Skeletal muscle is a tissue that is directly involved in the progression and persistence of type 2 diabetes (T2D), a disease that is becoming increasingly common. Gaining better insight into the mechanisms that are affecting skeletal muscle dysfunction in the context of T2D has the potential to lead to novel treatments for a large number of patients. Through its ability to emulate skeletal muscle architecture while also incorporating aspects of disease, tissue-engineered skeletal muscle (TE-SkM) has the potential to provide a means for rapid high-throughput discovery of therapies to treat skeletal muscle dysfunction, to include that which occurs with T2D. Muscle precursor cells isolated from lean or obese male Zucker diabetic fatty rats were used to generate TE-SkM constructs. Some constructs were treated with adipogenic induction media to accentuate the presence of adipocytes that is a characteristic feature of T2D skeletal muscle. The maturity (compaction and creatine kinase activity), mechanical integrity (Young's modulus), organization (myotube orientation), and metabolic capacity (insulin-stimulated glucose uptake) were all reduced by diabetes. Treating constructs with adipogenic induction media increased the quantity of lipid within the diabetic TE-SkM constructs, and caused changes in construct compaction, cell orientation, and insulin-stimulated glucose uptake in both lean and diabetic samples. Collectively, the findings herein suggest that the recapitulation of structural and metabolic aspects of T2D can be accomplished by engineering skeletal muscle in vitro.

Engineered Collagen Matrices

Collagen is the most abundant protein in mammals, accounting for approximately one-third of the total protein in the human body. Thus, it is a logical choice for the creation of biomimetic environments, and there is a long history of using collagen matrices for various tissue engineering applications. However, from a biomaterial perspective, the use of collagen-only scaffolds is associated with many challenges. Namely, the mechanical properties of collagen matrices can be difficult to tune across a wide range of values, and collagen itself is not highly amenable to direct chemical modification without affecting its architecture or bioactivity. Thus, many approaches have been pursued to design scaffold environments that display critical features of collagen but enable improved tunability of physical and biological characteristics. This paper provides a brief overview of approaches that have been employed to create such engineered collagen matrices. Specifically, these approaches include blending of collagen with other natural or synthetic polymers, chemical modifications of denatured collagen, de novo creation of collagen-mimetic chains, and reductionist methods to incorporate collagen moieties into other materials. These advancements in the creation of tunable, engineered collagen matrices will continue to enable the interrogation of novel and increasingly complex biological questions.

Engineering of biomaterials for tumor modeling

Development of biomaterials mimicking tumor and its microenvironment has recently emerged for the use of drug discovery, precision medicine, and cancer biology. These biomimetic models have developed by reconstituting tumor and stroma cells within the 3D extracellular matrix. The models are recently extended to recapitulate the in vivo tumor microenvironment, including biological, chemical, and mechanical conditions tailored for specific cancer type and its microenvironment. In spite of the recent emergence of various innovative engineered tumor models, many of these models are still early stage to be adapted for cancer research. In this article, we review the current status of biomaterials engineering for tumor models considering three main aspects - cellular engineering, matrix engineering, and engineering for microenvironmental conditions. Considering cancer-specific variability in these aspects, our discussion is focused on pancreatic cancer, specifically pancreatic ductal adenocarcinoma (PDAC). In addition, we further discussed the current challenges and future opportunities to create reliable and relevant tumor models.

Polymer microcapsules and microbeads as cell carriers for in vivo biomedical applications

Polymer microcarriers are being extensively explored as cell delivery vehicles in cell-based therapies and hybrid tissue and organ engineering. Spherical microcarriers are of particular interest due to easy fabrication and injectability. They include microbeads, composed of a porous matrix, and microcapsules, where matrix core is additionally covered with a semipermeable membrane. Microcarriers provide cell containment at implantation site and protect the cells from host immunoresponse, degradation and shear stress. Immobilized cells may be genetically altered to release a specific therapeutic product directly at the target site, eliminating side effects of systemic therapies. Cell microcarriers need to fulfil a number of extremely high standards regarding their biocompatibility, cytocompatibility, immunoisolating capacity, transport, mechanical and chemical properties. To obtain cell microcarriers of specified parameters, a wide variety of polymers, both natural and synthetic, and immobilization methods can be applied. Yet so far, only a few approaches based on cell-laden microcarriers have reached clinical trials. The main issue that still impedes progress of these systems towards clinical application is limited cell survival in vivo. Herein, we review polymer biomaterials and methods used for fabrication of cell microcarriers for in vivo biomedical applications. We describe their key limitations and modifications aiming at improvement of microcarrier in vivo performance. We also present the main applications of polymer cell microcarriers in regenerative medicine, pancreatic islet and hepatocyte transplantation and in the treatment of cancer. Lastly, we outline the main challenges in cell microimmobilization for biomedical purposes, the strategies to overcome these issues and potential future improvements in this area.

Type I Collagen-Fibrin Mixed Hydrogels: Preparation, Properties and Biomedical Applications

Type I collagen and fibrin are two essential proteins in tissue regeneration and have been widely used for the design of biomaterials. While they both form hydrogels via fibrillogenesis, they have distinct biochemical features, structural properties and biological functions which make their combination of high interest. A number of protocols to obtain such mixed gels have been described in the literature that differ in the sequence of mixing/addition of the various reagents. Experimental and modelling studies have suggested that such co-gels consist of an interpenetrated structure where the two proteins networks have local interactions only. Evidences have been accumulated that immobilized cells respond not only to the overall structure of the co-gels but can also exhibit responses specific to each of the proteins. Among the many biomedical applications of such type I collagen-fibrin mixed gels, those requiring the co-culture of two cell types with distinct affinity for these proteins, such as vascularization of tissue engineering constructs, appear particularly promising.

3D printing of multilayered scaffolds for rotator cuff tendon regeneration

Repairing massive rotator cuff tendon defects remains a challenge due to the high retear rate after surgical intervention. 3D printing has emerged as a promising technique that enables the fabrication of engineered tissues with heterogeneous structures and mechanical properties, as well as controllable microenvironments for tendon regeneration. In this study, we developed a new strategy for rotator cuff tendon repair by combining a 3D printed scaffold of polylactic-co-glycolic acid (PLGA) with cell-laden collagen-fibrin hydrogels. We designed and fabricated two types of scaffolds: one featuring a separate layer-by-layer structure and another with a tri-layered structure as a whole. Uniaxial tensile tests showed that both types of scaffolds had improved mechanical properties compared to single-layered PLGA scaffolds. The printed scaffold with collagen-fibrin hydrogels effectively supported the growth, proliferation, and tenogenic differentiation of human adipose-derived mesenchymal stem cells. Subcutaneous implantation of the multilayered scaffolds demonstrated their excellent in vivo biocompatibility. This study demonstrates the feasibility of 3D printing multilayered scaffolds for application in rotator cuff tendon regeneration.

Pancreatic extracellular matrix and platelet-rich plasma constructing injectable hydrogel for pancreas tissue engineering

The development of pancreatic extracellular matrices enriched with insulin-secreting β-cells is a promising tissue engineering approach to treat type 1 diabetes. However, its long-term therapeutic efficacy is restricted by the defensive mechanism of host immune response and the lack of developed vascularization as appropriate after transplantation. Platelet-rich plasma (PRP), as an autologous platelet concentrate, contains a large number of active factors that are essential for the cell viability, vascularization, and immune regulation. In this study, we have incorporated pancreatic extracellular matrix (PEM) with PRP to develop a three-dimensional (3D) injectable PEM-PRP hydrogel to coculture and transplant rat insulinoma cells (INS-1) and human umbilical vein endothelial cells (HUVECs). Results from this study demonstrated that PEM-PRP hydrogel mimicked the biochemical compositions of native extracellular matrices, and possessed the enhanced elastic modulus and resistance to enzymatic degradation that enabled biomaterials to maintain its volume and slowly degrade. Additionally, PEM-PRP hydrogel could release growth factors in a sustained manner. In vitro, PEM-PRP hydrogel significantly promoted the viability, insulin-secreting function, and insulin gene expression of gel encapsulated INS-1 cells. Moreover, HUVECs encapsulated in PEM-PRP hydrogel were found to constitute many lumen-like structures and exhibited high expression of proangiogenic genes. In vivo transplantation of PEM-PRP hydrogel encapsulated with INS-1 cells and HUVECs improved the viability of INS-1 cells, promoted vascularization, inhibited the host inflammatory response, and reversed hyperglycemia of diabetic rats. Our study suggests that the PEM-PRP hydrogel offers excellent biocompatibility and proangiogenic property, and may serve as an effective biomaterial platform to maintain the long-term survival and function of insulin-secreting β cells.

GROWTH AND CHARACTERIZATION OF A TISSUE-ENGINEERED CONSTRUCT FROM HUMAN CORONARY ARTERY SMOOTH MUSCLE CELLS

Objective

To optimize a bioengineered «I-Wire» platform to grow tissue-engineered constructs (TCs) derived from coronary artery smooth muscle cells and characterize the mechano-elastic properties of the grown TCs.

Materials and Methods

A fibrinogen-based cell mixture was pipetted in a casting mold having two parallel titanium anchoring wires inserted in the grooves on opposite ends of the mold to support the TC. The casting mold was 3 mm in depth, 2 mm in width and 12 mm in length. To measure TC deformation, a flexible probe with a diameter of 365 mk and a length of 42 mm was utilized. The deflection of the probe tip at various tensile forces applied to the TC was recorded using an inverted microscope optical recording system. The elasticity modulus was calculated based on a stretch-stress diagram reconstructed for each TC. The mechano-elastic properties of control TCs and TCs under the influence of isoproterenol (Iso), acetylcholine (ACh), blebbistatin (Bb) and cytochalasin D (Cyto-D) were evaluated. Immunohistochemical staining of smooth muscle α-actin, desmin and the cell nucleus was implemented for the structural characterization of the TCs.

Results

The TCs formed on day 5-6 of incubation. Subsequent measurements during the following 7 days did not reveal significant changes in elasticity. Values of the elastic modulus were 7.4 ± 1.5 kPa at the first day, 7.9 ± 1.4 kPa on the third day, and 7.8 ± 1.9 kPa on the seventh day of culturing after TC formation. Changes in the mechano-elastic properties of the TCs in response to the subsequent application of Bb and Cyto-D had a two-phase pattern, indicating a possible separation of active and passive elements of the TC elasticity. The application of 1 μM of Iso led to an increase in the value of the elastic modulus from 7.9 ± 1.5 kPa to 10.2 ± 2.1 kPa (p<0.05, n = 6). ACh did not cause a significant change in elasticity.

Conclusion

The system allows quantification of the mechano-elastic properties of TCs in response to pharmacological stimuli and can be useful to model pathological changes in vascular smooth muscle cells.

Enhanced vascularization and biocompatibility of rat pancreatic decellularized scaffolds loaded with platelet-rich plasma

The ultimate goal of pancreatic tissue engineering is to create a long-lived substitute organ to treat diabetes. However, the lack of neovascularization and the occurrence of immune response limit the efficacy of tissue-engineered pancreas after in vivo transplantation. Platelet-rich plasma (PRP) is an autologous platelet concentrate containing a large number of growth factors and immunoregulatory factors. The aim of this study was to evaluate rat pancreatic decellularized scaffold (PDS) loaded with PRP for vascularization, host inflammatory response and macrophage polarization in an animal model. The study results indicated that compared to PDS, PRP-loading PDS exhibited the enhanced mechanical properties and released growth factors in a slow and sustained manner to supplement the loss of growth factors during decellularization. In vitro, human umbilical vein endothelial cells (HUVECs) were seeded in PDS and PRP-loading PDS, and cultured in the circular perfusion system. When compared with PDS, PRP-loading PDS significantly promoted the colonization, proliferation and pro-angiogenic genes expression of cells on scaffolds. In vivo, PDS loaded with PRP then re-endothelialized with HUVECs were implanted subcutaneously in rats, which enhanced the angiogenesis of scaffolds, inhibited the host inflammatory response, and induced the polarization dominated by pro-regenerative M2 macrophages that also facilitated tissue vascular regeneration. Thus, the re-endothelialized PRP-loading PDS may represent a promising bioengineered pancreas with sustained vascularization and excellent biocompatibility.

Macromolecular gelatin properties affect fibrin microarchitecture and tumor spheroid behavior in fibrin-gelatin gels

The biophysical properties of extracellular matrices (ECM) are known to regulate cell behavior, however decoupling cell behavior changes due to the relative contributions of material microstructure versus biomechanics or nutrient permeability remains challenging, especially within complex, multi-material matrices. We developed four gelatin-fibrin interpenetrating network (IPN) formulations which are identical in composition but possess variable gelatin molecular weight distributions, and display differences in microstructure, biomechanics, and diffusivity. In this work we interrogate the response of multicellular tumor spheroids to these IPN formulations and found that a high stiffness, gelatin-network dominated IPNs impeded remodeling and invasion of multicellular tumor spheroids; whereas relatively lower stiffness, fibrin-network dominated IPNs permitted protease-dependent remodeling and spheroid invasion. Cell proliferation correlated to nutrient diffusivity across tested IPN formulations. These findings demonstrate the complexity of ECM IPNs, relative to single polymer matrices, and highlight that cell response does not derive from a single aspect of the ECM, but rather from the interplay of multiple biomechanical properties. The methodology developed here represents a framework for future studies which aim to characterize cellular phenotypic responses to biophysical cues present within complex, multi-material matrices.

Primary Human Osteoblasts Cultured in a 3D Microenvironment Create a Unique Representative Model of Their Differentiation Into Osteocytes

Microengineered systems provide an in vitro strategy to explore the variability of individual patient response to tissue engineering products, since they prefer the use of primary cell sources representing the phenotype variability. Traditional in vitro systems already showed that primary human osteoblasts embedded in a 3D fibrous collagen matrix differentiate into osteocytes under specific conditions. Here, we hypothesized that translating this environment to the organ-on-a-chip scale creates a minimal functional unit to recapitulate osteoblast maturation toward osteocytes and matrix mineralization. Primary human osteoblasts were seeded in a type I collagen hydrogel, to establish the role of lower (2.5 × 10⁵ cells/ml) and higher (1 × 10⁶ cells/ml) cell density on their differentiation into osteocytes. A custom semi-automatic image analysis software was used to extract quantitative data on cellular morphology from brightfield images. The results are showing that cells cultured at a high density increase dendrite length over time, stop proliferating, exhibit dendritic morphology, upregulate alkaline phosphatase (ALP) activity, and express the osteocyte marker dental matrix protein 1 (DMP1). On the contrary, cells cultured at lower density proliferate over time, do not upregulate ALP and express the osteoblast marker bone sialoprotein 2 (BSP2) at all timepoints. Our work reveals that microengineered systems create unique conditions to capture the major aspects of osteoblast differentiation into osteocytes with a limited number of cells. We propose that the microengineered approach is a functional strategy to create a patient-specific bone tissue model and investigate the individual osteogenic potential of the patient bone cells.

Hydrogel scaffolds based on blood plasma cryoprecipitate and collagen derived from various sources: Structural, mechanical and biological characteristics

At present there is a growing need for tissue engineering products, including the products of scaffold-technologies. Biopolymer hydrogel scaffolds have a number of advantages and are increasingly being used to provide means of cell transfer for therapeutic treatments and for inducing tissue regeneration. This work presents original hydrogel biopolymer scaffolds based on a blood plasma cryoprecipitate and collagen and formed under conditions of enzymatic hydrolysis. Two differently originated collagens were used for the scaffold formation. During this work the structural and mechanical characteristics of the scaffold were studied. It was found that, depending on the origin of collagen, scaffolds possess differences in their structural and mechanical characteristics. Both types of hydrogel scaffolds have good biocompatibility and provide conditions that maintain the three-dimensional growth of adipose tissue stem cells. Hence, scaffolds based on such a blood plasma cryoprecipitate and collagen have good prospects as cell carriers and can be widely used in regenerative medicine.

Enhanced osteogenesis of quasi-three-dimensional hierarchical topography

Natural extracellular matrices (ECMs) are three-dimensional (3D) and multi-scale hierarchical structure. However, coatings used as ECM-mimicking structures for osteogenesis are typically two-dimensional or single-scaled. Here, we design a distinct quasi-three-dimensional hierarchical topography integrated of density-controlled titania nanodots and nanorods. We find cellular pseudopods preferred to anchor deeply across the distinct 3D topography, dependently of the relative density of nanorods, which promote the osteogenic differentiation of osteoblast but not the viability of fibroblast. The in vivo experimental results further indicate that the new bone formation, the relative bone-implant contact as well as the push-put strength, are significantly enhanced on the 3D hierarchical topography. We also show that the exposures of HFN7.1 and mAb1937 critical functional motifs of fibronectin for cellular anchorage are up-regulated on the 3D hierarchical topography, which might synergistically promote the osteogenesis. Our findings suggest the multi-dimensions and multi-scales as vital characteristic of cell-ECM interactions and as an important design parameter for bone implant coatings.

Properties of interpenetrating polymer networks associating fibrin and silk fibroin networks obtained by a double enzymatic method

Fibrin gels are of interest as biomaterials for regenerative medicine but present poor mechanical properties, undergo fast degradation and strongly contract in presence of cells. To face these drawbacks, a fibrin network can be associated with another polymer network, in an Interpenetrating Polymer Network (IPN) architecture. In this study, we report the properties of an IPN comprising a fibrin (Fb) network and a silk fibroin (SF) network. This IPN is synthesized through the action of 2 enzymes, each one being specific of one protein gelation, i.e. thrombin (Tb) for Fb gelation, and horseradish peroxidase (HRP) for SF gelation. The effective formation of both Fb and SF networks in an IPN architecture was first verified at qualitative and quantitative levels. The resulting IPN was easily manipulable, displayed high viscoelastic properties and showed homogeneous macro- and micro-structure. Then the degradability of the IPN by two proteases, thermolysin (TL) and trypsin (TRY), obeying different mechanisms was presented. Finally, two-dimensional culture of human fibroblasts on the IPN surface induced little material contraction, while fibroblasts showed healthy morphology, displayed high viability and produced mature extracellular matrix (ECM) proteins. Taken together, the results suggest that this new IPN have a strong potential for tissue engineering and regenerative medicine.

Emerging Trends in Information-Driven Engineering of Complex Biological Systems

Synthetic biological systems are used for a myriad of applications, including tissue engineered constructs for in vivo use and microengineered devices for in vitro testing. Recent advances in engineering complex biological systems have been fueled by opportunities arising from the combination of bioinspired materials with biological and computational tools. Driven by the availability of large datasets in the "omics" era of biology, the design of the next generation of tissue equivalents will have to integrate information from single-cell behavior to whole organ architecture. Herein, recent trends in combining multiscale processes to enable the design of the next generation of biomaterials are discussed. Any successful microprocessing pipeline must be able to integrate hierarchical sets of information to capture key aspects of functional tissue equivalents. Micro- and biofabrication techniques that facilitate hierarchical control as well as emerging polymer candidates used in these technologies are also reviewed.

A Review of Integrin-Mediated Endothelial Cell Phenotype in the Design of Cardiovascular Devices

Sustained biomaterial thromboresistance has long been a goal and challenge in blood-contacting device design. Endothelialization is one of the most successful strategies to achieve long-term thromboresistance of blood-contacting devices, with the endothelial cell layer providing dynamic hemostatic regulation. It is well established that endothelial cell behavior is influenced by interactions with the underlying extracellular matrix (ECM). Numerous researchers have sought to exploit these interactions to generate improved blood-contacting devices by investigating the expression of hemostatic regulators in endothelial cells on various ECM coatings. The ability to select substrates that promote endothelial cell-mediated thromboresistance is crucial to advancing material design strategies to improve cardiovascular device outcomes. This review provides an overview of endothelial cell regulation of hemostasis, the major components found within the cardiovascular basal lamina, and the interactions of endothelial cells with prominent ECM components of the basement membrane. A summary of ECM-mimetic strategies used in cardiovascular devices is provided with a focus on the effects of key adhesion modalities on endothelial cell regulators of hemostasis.

Characterization of the tissue crossing the supratrochlear aperture of the humerus using histochemical techniques

INTRODUCTION

The supratrochlear aperture (STA) is the opening observed in the septum that separates the olecranon from the coronoid fossae. Numerous studies have shown that there is considerable variation in the occurrence of this feature within and among populations.

MATERIALS AND METHODS

Cadavers (n = 43) were assessed for the presence of the STA by means of X-ray. Ten samples of STA-bearing bones and an equal number of controls without STA were obtained from cadavers using a hole saw. These samples were decalcified, fixed in formalin and processed for histological assessment in differing (ascending) grades of alcohol before being embedded in paraffin wax. Sections (10 µm thick) were stained with haematoxylin and eosin (H&E) for general architecture as well as the rapid one-step Mallory-Heidenhain stain for bone and connective tissue.

RESULTS

The STA samples exhibited an abundance of connective tissue arranged in regular bundles of fibers across the STA. In contrast, the controls showed only bone tissue in the septum.

DISCUSSION AND CONCLUSION

The arrangement of connective tissue fibers organized in regular bundles is a characteristic of strength, which may indicate that the STA is under sustained stress or pressure from the olecranon and coronoid processes of the ulna. It remains debatable whether the STA should continue to be considered as a foramen in life as we demonstrate that it is obliterated by connective tissue. It contains no neurovascular structures, making it unlike other structures defined as foramina.

Mechanics of a two-fiber model with one nested fiber network, as applied to the collagen-fibrin system

The mechanical behavior of collagen-fibrin (col-fib) co-gels is both scientifically interesting and clinically relevant. Collagen-fibrin networks are a staple of tissue engineering research, but the mechanical consequences of changes in co-gel composition have remained difficult to predict or even explain. We previously observed fundamental differences in failure behavior between collagen-rich and fibrin-rich co-gels, suggesting an essential change in how the two components interact as the co-gel's composition changes. In this work, we explored the hypothesis that the co-gel behavior is due to a lack of percolation by the dilute component. We generated a series of computational models based on interpenetrating fiber networks. In these models, the major network component percolated the model space but the minor component did not, instead occupying a small island embedded within the larger network. Each component was assigned properties based on a fit of single-component gel data. Island size was varied to match the relative concentrations of the two components. The model predicted that networks rich in collagen, the stiffer component, would roughly match pure-collagen gel behavior with little additional stress due to the fibrin, as seen experimentally. For fibrin-rich gels, however, the model predicted a smooth increase in the overall network strength with added collagen, as seen experimentally but not consistent with an additive parallel model. We thus conclude that incomplete percolation by the low-concentration component of a co-gel is a major determinant of its macroscopic properties, especially if the low-concentration component is the stiffer component.

STATEMENT OF SIGNIFICANCE

Models for the behavior of fibrous networks have useful applications in many different fields, including polymer science, textiles, and tissue engineering. In addition to being important structural components in soft tissues and blood clots, these protein networks can serve as scaffolds for bioartificial tissues. Thus, their mechanical behavior, especially in co-gels, is both interesting from a materials science standpoint and significant with regard to tissue engineering.

Evaluation of Fibrin-Based Interpenetrating Polymer Networks as Potential Biomaterials for Tissue Engineering

Interpenetrating polymer networks (IPNs) have gained great attention for a number of biomedical applications due to their improved properties compared to individual components alone. In this study, we investigated the capacity of newly-developed naturally-derived IPNs as potential biomaterials for tissue engineering. These IPNs combine the biologic properties of a fibrous fibrin network polymerized at the nanoscale and the mechanical stability of polyethylene oxide (PEO). First, we assessed their cytotoxicity in vitro on L929 fibroblasts. We further evaluated their biocompatibility ex vivo with a chick embryo organotypic culture model. Subcutaneous implantations of the matrices were subsequently conducted on nude mice to investigate their biocompatibility in vivo. Our preliminary data highlighted that our biomaterials were non-cytotoxic (viability above 90%). The organotypic culture showed that the IPN matrices induced higher cell adhesion (across all the explanted organ tissues) and migration (skin, intestine) than the control groups, suggesting the advantages of using a biomimetic, yet mechanically-reinforced IPN-based matrix. We observed no major inflammatory response up to 12 weeks post implantation. All together, these data suggest that these fibrin-based IPNs are promising biomaterials for tissue engineering.

Collagen-Fibrinogen Lyophilised Scaffolds for Soft Tissue Regeneration

A significant body of research has considered collagen as a scaffold material for soft tissue regeneration. The main structural component of extra-cellular matrix (ECM), collagen’s advantages over synthetic polymers are numerous. However, for applications where higher stiffness and stability are required, significant cross-linking may affect bioactivity. A carbodiimide (EDC) cross-linking route consumes carboxylate groups that are key to collagen’s essential cell recognition motifs (GxOGER). Fibrinogen was considered as a promising additive as it plays a key role in the process of wound repair and contains RGD integrin binding sites which bind to a variety of cells, growth factors and cytokines. Fibrinogen’s binding sites however, also contain the same carboxylate groups as collagen. We have successfully produced highly interconnected, porous collagen-fibrinogen scaffolds using a lyophilisation technique and micro-computed tomography demonstrated minimal influence of either fibrinogen content or cross-linking concentration on the scaffold structure. The specific biological effect of fibrinogen additions into cross-linked collagen are considered by using films as a model for the struts of bulk scaffolds. By considering various additions of fibrinogen to the collagen film with increasing degrees of cross-linking, this study demonstrates a significant biological advantage with fibrinogen addition across the cross-linking concentrations typically applied to collagen-based scaffolds.

Fibrin in Reproductive Tissue Engineering: A Review on Its Application as a Biomaterial for Fertility Preservation

In recent years, reproductive medicine has made good use of tissue engineering and regenerative medicine techniques to develop alternatives to restore fertility in cancer patients. For young female cancer patients who cannot undergo any of the currently applied strategies due to the possible presence of malignant cells in their ovaries, the challenge is creating an in vitro or in vivo artificial ovary using carefully selected biomaterials. Thanks to its numerous qualities, fibrin has been widely used as a scaffold material for fertility preservation applications. The goal of this review is to examine and discuss the applications and advantages of this biopolymer for fertility restoration in cancer patients, and consider the main results achieved so far.

Tissue engineering-based therapeutic strategies for vocal fold repair and regeneration

Vocal folds are soft laryngeal connective tissues with distinct layered structures and complex multicomponent matrix compositions that endow phonatory and respiratory functions. This delicate tissue is easily damaged by various environmental factors and pathological conditions, altering vocal biomechanics and causing debilitating vocal disorders that detrimentally affect the daily lives of suffering individuals. Modern techniques and advanced knowledge of regenerative medicine have led to a deeper understanding of the microstructure, microphysiology, and micropathophysiology of vocal fold tissues. State-of-the-art materials ranging from extracecullar-matrix (ECM)-derived biomaterials to synthetic polymer scaffolds have been proposed for the prevention and treatment of voice disorders including vocal fold scarring and fibrosis. This review intends to provide a thorough overview of current achievements in the field of vocal fold tissue engineering, including the fabrication of injectable biomaterials to mimic in vitro cell microenvironments, novel designs of bioreactors that capture in vivo tissue biomechanics, and establishment of various animal models to characterize the in vivo biocompatibility of these materials. The combination of polymeric scaffolds, cell transplantation, biomechanical stimulation, and delivery of antifibrotic growth factors will lead to successful restoration of functional vocal folds and improved vocal recovery in animal models, facilitating the application of these materials and related methodologies in clinical practice.

Enhancement of posterolateral lumbar spine fusion using recombinant human bone morphogenetic protein-2 and mesenchymal stem cells delivered in fibrin glue

Mesenchymal stem cells have shown great potential for accelerating bone healing. In the present study, we evaluate the efficacy of fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 composite for posterolateral spinal fusion in a rabbit model. Forty adult rabbits underwent posterolateral intertransverse fusion at the L5–L6 level. The animals were randomly divided into four groups based on the implant material: fibrin glue, fibrin glue/mesenchymal stem cells composite, fibrin glue-recombinant human bone morphogenetic protein-2 (fibrin glue/recombinant human bone morphogenetic protein-2) composite, and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 composite. After six weeks, the rabbits were euthanized for manual palpation, radiographic examination, biomechanical testing, and histology. Manual palpation results showed that the fusion rate for fibrin glue, fibrin glue/mesenchymal stem cells, fibrin glue/recombinant human bone morphogenetic protein-2, and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 was 0, 0, 40%, and 70%, respectively. Moreover, fusion rate determined by radiographic examination for fibrin glue, fibrin glue/mesenchymal stem cells, fibrin glue/recombinant human bone morphogenetic protein-2, and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 was 0, 0, 40%, and 80%, respectively. Gray analysis showed that fibrin glue/recombinant human bone morphogenetic protein-2 group had higher ossification area and density than fibrin glue group; and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 group had higher ossification area and density than fibrin glue/recombinant human bone morphogenetic protein-2 group. Formation of continuous bone masses between L5 and L6 level in mesenchymal stem cells/recombinant human bone morphogenetic protein-2/fibrin glue group was further confirmed by computed tomography scanning and three-dimensional reconstruction. Biomechanical testing demonstrated that the fusion strength (flexion, extension, lateral bending, and axial rotation) in fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 group is significantly higher than that in fibrin glue/recombinant human bone morphogenetic protein-2 group. The formation of mature bone tissues between transverse processes of the fused specimens from both fibrin glue/recombinant human bone morphogenetic protein-2, and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 groups was confirmed by HE staining, and quantitative real-time polymerase chain reaction results showed the upregulation of CD31, type I collagen, osteocalcin, and osteonectin in the fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 group. In conclusion, our findings show that mesenchymal stem cells delivered with recombinant human bone morphogenetic protein-2 using fibrin glue as carrier are more effective in enhancing spine fusion than recombinant human bone morphogenetic protein-2 without mesenchymal stem cells in the rabbit model.

Hyaluronic acid-fibrin interpenetrating double network hydrogel prepared in situ by orthogonal disulfide cross-linking reaction for biomedical applications

To strengthen the mechanical properties of a fibrin gel and improve its applicability as a scaffold for tissue engineering (TE) applications, a strategy for the in situ preparation of the interpenetrating network (IPN) of fibrin and hyaluronic acid (HA) was developed on the basis of simultaneous and orthogonal fibrinogenesis and disulfide cross-linking. The synthetic pathway included the preparation of mutually reactive HA derivatives bearing thiol and 2-dithiopyridyl groups. Combining thiol-derivatized HA with thrombin and 2-dithiopyridyl-modified HA with fibrinogen and then mixing the obtained liquid formulations afforded IPNs with fibrin-resembling fibrillar architectures at different ratios between fibrin and HA networks. The formation of two networks was confirmed by conducting reference experiments with the compositions lacking one of the four components. The composition of 2% (w/v) fibrin and 1% (w/v) HA showed the highest storage modulus (G'), as compared with the single network counterparts. The degradation of fibrin in IPN hydrogels was slower than that in pure fibrin gels both during incubation of the hydrogels in a fibrin-cleaving nattokinase solution and during the culturing of cells after their encapsulation in the hydrogels. Together with the persistence of HA network, it permitted longer cell culturing time in the IPN. Moreover, the proliferation and spreading of MG63 cells that express the hyaluronan receptor CD44 in IPN hydrogel was increased, as compared with its single network analogues. These results are promising for tunable ECM-based materials for TE and regenerative medicine.

STATEMENT OF SIGNIFICANCE

The present work is devoted to in situ fabrication of injectable extracellular matrix hydrogels through simultaneous generation of networks of fibrin and hyaluronic acid (HA) that interpenetrate each other. This is accomplished by combination of enzymatic fibrin cross-linking with orthogonal disulphide cross-linking of HA. High hydrophilicity of HA prevents compaction of the fibrin network, while fibrin provides an adhesive environment for in situ encapsulated cells. The interpenetrating network hydrogel shows an increased stiffness along with a lower degradation rate of fibrin in comparison to the single fibrin network. As a result, the cells have sufficient time for the remodelling of the scaffold. This new approach can be applied for modular construction of in vitro tissue models and tissue engineering scaffolds in vivo.

A novel platelet lysate hydrogel for endothelial cell and mesenchymal stem cell-directed neovascularization

Mesenchymal stem cells (MSC) hold promise in promoting vascular regeneration of ischemic tissue in conditions like critical limb ischemia of the leg. However, this approach has been limited in part by poor cell retention and survival after delivery. New biomaterials offer an opportunity to localize cells to the desired tissue after delivery, but also to improve cell survival after delivery. Here we characterize the mechanical and microstructural properties of a novel hydrogel composed of pooled human platelet lysate (PL) and test its ability to promote MSC angiogenic activity using clinically relevant in vitro and in vivo models. This PL hydrogel had comparable storage and loss modulus and behaved as a viscoelastic solid similar to fibrin hydrogels despite having 1/4-1/10th the fibrin content of standard fibrin gels. Additionally, PL hydrogels enabled sustained release of endogenous PDGF-BB for up to 20days and were resistant to protease degradation. PL hydrogel stimulated pro-angiogenic activity by promoting human MSC growth and invasion in a 3D environment, and enhancing endothelial cell sprouting alone and in co-culture with MSCs. When delivered in vivo, the combination of PL and human MSCs improved local tissue perfusion after 8days compared to controls when assessed with laser Doppler perfusion imaging in a murine model of hind limb ischemia. These results support the use of a PL hydrogel as a scaffold for MSC delivery to promote vascular regeneration.

STATEMENT OF SIGNIFICANCE

Innovative strategies for improved retention and viability of mesenchymal stem cells (MSCs) are needed for cellular therapies. Human platelet lysate is a potent serum supplement that improves the expansion of MSCs. Here we characterize our novel PL hydrogel's desirable structural and biologic properties for human MSCs and endothelial cells. PL hydrogel can localize cells for retention in the desired tissue, improves cell viability, and augments MSCs' angiogenic activity. As a result of these unique traits, PL hydrogel is ideally suited to serve as a cell delivery vehicle for MSCs injected into ischemic tissues to promote vascular regeneration, as demonstrated here in a murine model of hindlimb ischemia.

Tissue-Engineered Vocal Fold Mucosa Implantation in Rabbits

OBJECTIVE

To assess phonatory function and wound healing of a tissue-engineered vocal fold mucosa (TE-VFM) in rabbits. An "artificial" vocal fold would be valuable for reconstructing refractory scars and resection defects, particularly one that uses readily available autologous cells and scaffold. This work implants a candidate TE-VFM after resecting native epithelium and lamina propria in rabbits.

STUDY DESIGN

Prospective animal study.

SETTING

Research laboratory.

SUBJECTS AND METHODS

Rabbit adipose-derived stem cells were isolated and cultured in three-dimensional fibrin scaffolds to form TE-VFM. Eight rabbits underwent laryngofissure, unilateral European Laryngologic Society type 2 cordectomy, and immediate reconstruction with TE-VFM. After 4 weeks, larynges were excised, phonated, and examined by histology.

RESULTS

Uniform TE-VFM implants were created, with rabbit mesenchymal cells populated throughout fibrin hydrogels. Rabbits recovered uneventfully after implantation. Phonation was achieved in all, with mucosal waves evident at the implant site. Histology after 4 weeks showed resorbed fibrin matrix, continuous epithelium, and mildly increased collagen relative to contralateral unoperated vocal folds. Elastic fiber appearance was highly variable. Inflammatory cell infiltrate was limited to animals receiving sex-mismatched implants.

CONCLUSION

TE-VFMs were successfully implanted into 8 rabbits, with minor evidence of scar formation and immune reaction. Vibration was preserved 4 weeks after resecting and reconstructing the complete vocal fold cover layer. Further studies will investigate the mechanism and durability of improvement. TE-VFM with autologous cells is a promising new approach for vocal fold reconstruction.

Design and Validation of a Vacuum Assisted Anchorage for the Uniaxial Tensile Testing of Soft Materials

Current commercial tensile testing systems use spring-loaded or other compression-based grips to clamp materials in place posing a problem for very soft or delicate materials that cannot withstand this mechanical clamping force. In order to perform uniaxial tensile tests on soft tissues or materials, we have created a novel vacuum-assisted anchor (VAA). Fibrin gels were subjected to uniaxial extension, and the testing data was used to determine material mechanical properties. Utilizing the VAA, we achieved successful tensile breaks of soft fibrin gels while finding statistically significant differences between the mechanical properties of gels fabricated at two different fibrinogen concentrations.

Hydrogels based on collagen and fibrin – frontiers and applications

Hydrogels are a versatile tool for a multitude of applications in biomedical research and clinical practice. Especially collagen and fibrin hydrogels are distinguished by their excellent biocompatibility, natural capacity for cell adhesion and low immunogenicity. In many ways, collagen and fibrin represent an ideal biomaterial, as they can serve as a scaffold for tissue regeneration and promote the migration of cells, as well as the ingrowth of tissues. On the other hand, pure collagen and fibrin materials are marked by poor mechanical properties and rapid degradation, which limits their use in practice. This paper will review methods of modification of natural collagen and fibrin materials to next-generation materials with enhanced stability. A special focus is placed on biomedical products from fibrin and collagen already on the market. In addition, recent research on the in vivo applications of collagen and fibrin-based materials will be showcased.

Angiogenin-loaded fibrin/bone powder composite scaffold for vascularized bone regeneration

Background

Angiogenin (ANG) is a potent stimulator of angiogenesis. The aim of this study was to fabricate an ANG-loaded scaffold and to evaluate its angiogenic and osteogenic effects. In this study, we fabricated an ANG-loaded scaffold using bovine bone powder and fibrin glue. We then evaluated the structural, morphological, and mechanical properties of the scaffold and the in vitro release profile of ANG. Cell proliferation, viability, and adhesion were evaluated using endothelial cells in vitro, and angiogenesis and new bone formation were evaluated using a rabbit calvarial defect model in vivo.

Results

Micro-computed tomography imaging showed that the bone powder was uniformly distributed in the scaffold, and scanning electron microscopy showed that the bone powder was bridged by polymerized fibrin. The porosity and compressive strength of the scaffolds were ~60 % and ~0.9 MPa, respectively, and were not significantly altered by ANG loading. In vitro, at 7 days, approximately 0.4 μg and 1.3 μg of the ANG were released from the FB/ANG 0.5 and FB/ANG 2.0, respectively and sustained slow release was observed until 25 days. The released ANG stimulated cell proliferation and adherence and was not cytotoxic. Furthermore, in vivo implantation resulted in enhanced angiogenesis, and new bone formation depended on the amount of loaded ANG.

Conclusions

These studies demonstrate that a fibrin and bone powder scaffold loaded with ANG might be useful to promote bone regeneration by enhanced angiogenesis.

Characterization of Fibrin and Collagen Gels for Engineering Wound Healing Models

Hydrogels are used for 3D in vitro assays and tissue engineering and regeneration purposes. For a thorough interpretation of this technology, an integral biomechanical characterization of the materials is required. In this work, we characterize the mechanical and functional behavior of two specific hydrogels that play critical roles in wound healing, collagen and fibrin. A coherent and complementary characterization was performed using a generalized and standard composition of each hydrogel and a combination of techniques. Microstructural analysis was performed by scanning electron microscopy and confocal reflection imaging. Permeability was measured using a microfluidic-based experimental set-up, and mechanical responses were analyzed by rheology. We measured a pore size of 2.84 and 1.69 μm for collagen and fibrin, respectively. Correspondingly, the permeability of the gels was 1.00·10⁻¹² and 5.73·10⁻¹³ m². The shear modulus in the linear viscoelastic regime was 15 Pa for collagen and 300 Pa for fibrin. The gels exhibited strain-hardening behavior at ca. 10% and 50% strain for fibrin and collagen, respectively. This consistent biomechanical characterization provides a detailed and robust starting point for different 3D in vitro bioapplications, such as collagen and/or fibrin gels. These features may have major implications for 3D cellular behavior by inducing divergent microenvironmental cues.

Inducible VEGF expression by human embryonic stem cell-derived mesenchymal stromal cells reduces the minimal islet mass required to reverse diabetes

Islet transplantation has been hampered by loss of function due to poor revascularization. We hypothesize that co-transplantation of islets with human embryonic stem cell-derived mesenchymal stromal cells that conditionally overexpress VEGF (hESC-MSC:VEGF) may augment islet revascularization and reduce the minimal islet mass required to reverse diabetes in mice. HESC-MSCs were transduced by recombinant lentiviruses that allowed conditional (Dox-regulated) overexpression of VEGF.

HESC-MSC

VEGF were characterized by tube formation assay. After co-transplantation of hESC-MSC:VEGF with murine islets in collagen-fibrin hydrogel in the omental pouch of diabetic nude mice, we measured blood glucose, body weight, glucose tolerance and serum C-peptide. As control, islets were transplanted alone or with non-transduced hESC-MSCs. Next, we compared functional parameters of 400 islets alone versus 200 islets co-transplanted with hESC-MSC:VEGF. As control, 200 islets were transplanted alone. Metabolic function of islets transplanted with hESC-MSC:VEGF significantly improved, accompanied by superior graft revascularization, compared with control groups. Transplantation of 200 islets with hESC-MSC:VEGF showed superior function over 400 islets alone. We conclude that co-transplantation of islets with VEGF-expressing hESC-MSCs allowed for at least a 50% reduction in minimal islet mass required to reverse diabetes in mice. This approach may contribute to alleviate the need for multiple donor organs per patient.

Characterizing natural hydrogel for reconstruction of three-dimensional lymphoid stromal network to model T-cell interactions

Hydrogels have been used in regenerative medicine because they provide a three-dimensional environment similar to soft tissues, allow diffusion of nutrients, present critical biological signals, and degrade via endogenous enzymatic mechanisms. Herein, we developed in vitro system mimicking cell-cell and cell-matrix interactions in secondary lymphoid organs (SLOs). Existing in vitro culture systems cannot accurately represent the complex interactions happening between T-cells and stromal cells in immune response. To model T-cell interaction in SLOs in vitro, we encapsulated stromal cells in fibrin, collagen, or fibrin-collagen hydrogels and studied how different mechanical and biological properties affect stromal network formation. Overall, fibrin supplemented with aprotinin was superior to collagen and fibrin-collagen in terms of network formation and promotion of T-cell penetration. After 8 days of culture, stromal networks formed through branching and joining with other adjacent cell populations. T-cells added to the newly formed stromal networks migrated and attached to stromal cells, similar to the T-cell zones of the lymph nodes in vivo. Our results suggest that the constructed three-dimensional lymphoid stromal network can mimic the in vivo environment and allow the modeling of T-cell interaction in SLOs.

The effects of fibrinogen concentration on fibrin/atelocollagen composite gel: an in vitro and in vivo study in rabbit calvarial bone defect

OBJECTIVE

This study aimed to optimize the fibrinogen concentration in fibrin and atelocollagen (AT-COL) (fibrin/AT-COL) composite gel for improving bone regeneration.

METHODS AND MATERIALS

The fibrin/AT-COL composite gels were fabricated using various fibrinogen concentrations, and the microstructure and mechanical properties of the resulting composite gels analyzed. The cytocompatibility of the composite gels was examined using human mesenchymal stem cell (hMSCs). Furthermore, in nine rabbits, the in vivo bone regeneration efficiency was evaluated using a rabbit calvarial defects model at 2 weeks (n = 3), 4 weeks (n = 3), and 8 weeks (n = 3).

RESULTS

Scanning electron microscopy analysis revealed the formation of a fibrin layer matrix and collagen fibril networks. The composite gel containing 40 mg/ml fibrinogen showed a densely packed fibrin matrix and displayed superior mechanical properties. Cells cultured in the composite gels prepared with 5-20 mg/ml fibrinogen appeared elongated, with a spindle-like morphology. At a higher fibrinogen concentration (40 mg/ml), many cells were rounded and showed limited viability. In an in vivo study, at 8 weeks, the volume of fibrin/AT-COL gel (P = 0.02) was significantly higher than that of fibrin gel alone in the newly formed bone. Histological analysis revealed more islands of newly formed bone filling the central area of the defect in the fibrin/AT-COL gel-implanted animals.

CONCLUSION

Our results demonstrate that optimization of the fibrinogen content of fibrin/AT-COL composites should be beneficial for bone tissue engineering.

Implanted cell-dense prevascularized tissues develop functional vasculature that supports reoxygenation after thrombosis

Achieving adequate vascularization within implanted engineered tissues is a significant obstacle to maintaining viability and functionality. In vitro prevascularization of engineered tissues has been explored as a potential solution to this challenge. The traditional paradigm of in vitro prevascularization is to implant an engineered tissue with a preformed vascular network that is perfused after anastomosis with the host circulation. We investigated the efficacy of this strategy by implanting cell-dense prevascularized tissues created via cell-mediated contraction and composed of collagen and a collagen-fibrin mixture into dorsal window chambers surgically prepared on immunocompromised mice. We found that host-implant anastomosis takes place in 2-6 days and that perfusion of vessels within the implants is subsequently restricted by thrombosis. However, by day 7, a functional vascular network composed of host and implant vessels developed. Prevascularization enhanced intra-implant pO2 significantly as early as 2 days postimplantation, reaching a maximum of 55 mmHg by day 8, which was significantly greater than the maximum within cellularized control tissues (18 mmHg). By day 14, collagen tissues supported ∼ 0.51 × 10(9) implanted and host-derived cells per mL. Our findings elucidate key features of in vitro prevascularization that can be used toward the design of larger and more functionally complex engineered tissues.