Interplay of metal node and amine functionality in NH2-MIL-53: modulating breathing behavior through intra-framework interactions

Tuning strategies of MIL metal organic frameworks for adsorptive removal of formaldehyde in air

Materials Institute Lavoisier (MIL) metal organic frameworks (MOFs) are known for their potential to adsorb gaseous organic pollutants. This study explores the synergistic effects between the selection of central metals (e.g., titanium, iron, and aluminum) and the incorporation of -NH2 groups in terms of adsorption efficiency against gaseous formaldehyde (FA). A group of the pristine MIL MOFs is synthesized using three different metals (i.e., titanium, iron, and aluminum) and terephthalic acid along with their NH2 derivatives using 2-aminoterephthalic acid. Among the pristine forms, MIL-125(Ti) achieves the highest FA adsorption capacity (Q) of 26.96 mg g-1 and a partition coefficient (PC) of 0.0898 mol kg-1 Pa-1. Further, amination significantly improves the FA adsorption potential of NH2-MIL-125(Ti) with a Q value of 91.22 mg g-1 (PC = 0.3038 mol kg-1 Pa-1). In situ diffuse reflectance infrared Fourier-transform spectroscopy reveals that the FA adsorption of plain MILs should be governed primarily by physisorption. In contrast, FA adsorption of NH2-MILs appears to be regulated by both physisorption and chemisorption, while the latter being affected mainly through FA-NH2 interactions (Schiff base reactions). These findings provide valuable insights into the utility of aminated MIL sorbents, possibly toward the efficient management of indoor air quality.

Studies on ultrafast and remarkable removal of phosphate from sewage water by metal-organic frameworks

In the proposed research, a lanthanum-doped metal-organic framework (La-ATP) has been synthesised to remove phosphate from contaminated aqueous solutions. La-ATP was synthesised by a green energy-saving route using microwave irradiation and exhibited a phenomenal sorption capacity of 290 mg/g for the removal of phosphate. At a minimal dose of 0.1 g/L, 25 mg/L of phosphate gets reduced to 6.3 mg/L within 5 min and reaches equilibrium in 25 min. The isoelectric point of La-ATP was found to be 8.99, and it is efficient in removing phosphate over a wide range of pH 5-10. The existence of commonly occurring competing anions like sulphate, fluoride, chloride, arsenate, bicarbonate, and nitrate does not affect the uptake capacity of La-ATP towards phosphate ions. Furthermore, the robustness of La-ATP is demonstrated by its applicability to remove phosphate from real-life sewage water by reducing 10 mg/L of phosphorus from sewage water to < 0.02 mg/L. The primary mechanism governing phosphate removal was found to be ionic interaction and ligand exchange. Therefore, La-ATP can be considered a viable candidate for the treatment of eutrophic water streams because of its high sorption capacity, super-fast kinetics, and adaptability to contaminated sewage.

Pressure-induced postsynthetic cluster anion substitution in a MIL-53 topology scandium metal-organic framework

Postsynthetic modification of metal-organic frameworks (MOFs) has proven to be a hugely powerful tool to tune physical properties and introduce functionality, by exploiting reactive sites on both the MOF linkers and their inorganic secondary building units (SBUs), and so has facilitated a wide range of applications. Studies into the reactivity of MOF SBUs have focussed solely on removal of neutral coordinating solvents, or direct exchange of linkers such as carboxylates, despite the prevalence of ancillary charge-balancing oxide and hydroxide ligands found in many SBUs. Herein, we show that the μ2-OH ligands in the MIL-53 topology Sc MOF, GUF-1, are labile, and can be substituted for μ2-OCH3 units through reaction with pore-bound methanol molecules in a very rare example of pressure-induced postsynthetic modification. Using comprehensive solid-state NMR spectroscopic analysis, we show an order of magnitude increase in this cluster anion substitution process after exposing bulk samples suspended in methanol to a pressure of 0.8 GPa in a large volume press. Additionally, single crystals compressed in diamond anvil cells with methanol as the pressure-transmitting medium have enabled full structural characterisation of the process across a range of pressures, leading to a quantitative single-crystal to single-crystal conversion at 4.98 GPa. This unexpected SBU reactivity - in this case chemisorption of methanol - has implications across a range of MOF chemistry, from activation of small molecules for heterogeneous catalysis to chemical stability, and we expect cluster anion substitution to be developed into a highly convenient novel method for modifying the internal pore surface and chemistry of a range of porous materials.

Kinetics of Guest-Induced Structural Transitions in Metal-Organic-Framework MIL-53(Al)-NH2 Probed by High-Pressure Nuclear Magnetic Resonance

A nuclear magnetic resonance (NMR) study of a pore opening in amino-functionalized metal-organic framework (MOF) MIL-53(Al) in response to methane pressure variation is presented. Variations of both NMR signal intensities and transversal relaxation rates for methane are found to reveal hysteretic structural transitions in the MOF material, which are smeared out over broad pressure ranges. Experiments with pressure reversals upon an incomplete adsorption/desorption gave deeper insight into the microscopic transition mechanisms. These experiments have unequivocally proven that the non-stepwise pore opening/closing transitions observed in the experiments are governed by a distribution of the opening/closing pressures over different MOF crystallites, for example, due to a distribution of the crystal sizes or shapes. The slow kinetics of the structural transitions measured in the hysteresis regime revealed a complex free energy landscape for the phase transition process.

Strengthening Intraframework Interaction within Flexible MOFs Demonstrates Simultaneous Sieving Acetylene from Ethylene and Carbon Dioxide

Efficient separation of acetylene (C₂ H₂ )/ethylene (C₂ H₄ ) and acetylene/carbon dioxide (CO₂ ) by adsorption is an industrially promising process, but adsorbents capable of simultaneously capturing trace acetylene from ethylene and carbon dioxide are scarce. Herein, a gate-opening effect on three isomorphous flexible metal-organic frameworks (MOFs) named Co(4-DPDS)₂ MO₄ (M = Cr, Mo, W; 4-DPDS = 4,4-dipyridyldisulfide) is modulated by anion pillars substitution. The shortest CrO₄ ^2- strengthens intraframework hydrogen bonding and thus blocks structural transformation after activation, striking a good balance among working capacity, separation selectivity, and trace impurity removal of flexible MOFs out of nearly C₂ H₂ /C₂ H₄ and C₂ H₂ /CO₂ molecular sieving. The exceptional separation performance of Co(4-DPDS)₂ CrO₄ is confirmed by dynamic breakthrough experiments. It reveals the specific threshold pressures control in anion-pillared flexible materials enabled elimination of the impurity leakage to realize high purity products through precise control of the intraframework interaction. The adsorption mechanism and multimode structural transformation property are revealed by both calculations and crystallography studies. This work demonstrates the feasibility of modulating flexibility for controlling gate-opening effect, especially for some cases of significant aperture shrinkage after activation.

A critical review on the synthesis of NH2-MIL-53(Al) based materials for detection and removal of hazardous pollutants

Nowadays, emerging hazardous pollutants have caused many harmful effects on the environment and human health, calling for the state of the art methods for detection, qualification, and treatment. Metal-organic frameworks are porous, flexible, and versatile materials with unique structural properties, which can solve such problems. In this work, we reviewed the synthesis, activation, and characterization, and potential applications of NH₂-MIL-53(Al). This material exhibited intriguing breathing effects, and obtained very high surface areas (182.3-1934 m²/g) with diverse morphologies. More importantly, NH₂-MIL-53(Al) based materials could be used for the detection and removal of various toxic pollutants such as organic dyes, pharmaceuticals, herbicides, insecticides, phenols, heavy metals, and fluorides. We shed light on plausible adsorption mechanisms such as hydrogen bonds, π-π stacking interactions, and electrostatic interactions onto NH₂-MIL-53(Al) adsorbents. Interestingly, NH₂-MIL-53(Al) based adsorbents could be recycled for many cycles with high stability. This review also recommended that NH₂-MIL-53(Al) based materials can be a good platform for the environmental remediation fields.

Novel benzylphosphate-based covalent porous organic polymers for the effective capture of rare earth elements from aqueous solutions

It has been a major challenge to develop stable and cost-effective porous materials that efficiently recover heavy rare earth elements (HREEs) due to ever-increasing demand, low availability and high cost of HREEs. This study presents two novel benzylphosphate-based covalent porous organic polymers (BPOP-1 and BPOP-2) that were prepared by facile one-pot Friedel-Crafts reactions. Various analytical techniques are used to investigate the successful syntheses of BPOP materials and establish their material properties, which include an unusual crystalline nature, large surface area, hierarchical pore structure, and superior chemical stabilities. The BPOPs effectively adsorb, and thus remove HREEs from aqueous media. In particular, BPOP-1 had higher phosphate content and exhibits superior adsorption capacities (Eu³⁺: 289.5; Gd³⁺: 292.7; Tb³⁺: 294.4; Dy³⁺: 301.9 mg/g) than BPOP-2, while BPOP-2 had higher mesoporosity and correspondingly supports faster adsorption kinetics. Remarkably, both BPOP materials exhibit some of the highest HREE adsorption capacities reported to date, the selective capture of Dy³⁺ ions, and excellent cyclic adsorption/desorption properties. We provide a potential adsorption mechanism for Dy³⁺ capture by the BPOP adsorbent. These demonstrate that introducing phosphate functionality into a robust porous polymer backbone with high surface area is a promising strategy for selective HREEs capture from wastewater.

Application of Metal-Organic Framework-Based Composites for Gas Sensing and Effects of Synthesis Strategies on Gas-Sensitive Performance

Gas sensing materials, such as semiconducting metal oxides (SMOx), carbon-based materials, and polymers have been studied in recent years. Among of them, SMOx-based gas sensors have higher operating temperatures; sensors crafted from carbon-based materials have poor selectivity for gases and longer response times; and polymer gas sensors have poor stability and selectivity, so it is necessary to develop high-performance gas sensors. As a porous material constructed from inorganic nodes and multidentate organic bridging linkers, the metal-organic framework (MOF) shows viable applications in gas sensors due to its inherent large specific surface area and high porosity. Thus, compounding sensor materials with MOFs can create a synergistic effect. Many studies have been conducted on composite MOFs with three materials to control the synergistic effects to improve gas sensing performance. Therefore, this review summarizes the application of MOFs in sensor materials and emphasizes the synthesis progress of MOF composites. The challenges and development prospects of MOF-based composites are also discussed.

Tuning the excited-state intramolecular proton transfer (ESIPT)-based luminescence of metal-organic frameworks by metal nodes toward versatile photoluminescent applications

Here, using three metal cations (Mg2+, Al3+, and Zr4+) and an excited-state intramolecular proton transfer (ESIPT) active linker, 2,5-dihydroxyterephthalic acid (H2DHT), three luminescent metal-organic frameworks (LMOFs) were obtained. Importantly, their ESIPT-based luminescence originated from the linker was systematically tuned in emission profiles including intensity, emission color, and quantum efficiency in the solution as well as in the solid state, which is largely dependent on the composition and structural characteristics of these three LMOFs. Similar to the free linker, the Mg-based MOF possesses a relatively strong luminescence, the Al-based MOF has moderate luminescence due to the breathing effect, and the Zr-based MOF is very weakly luminescent, mainly caused by the LMCT process. Benefiting from unique emission behaviors of these three LMOFs, we further modulated their ESIPT-based luminescence through the interplay between guest species and components of LMOFs by combining with various photophysical processes, and successfully explored their potential applications as versatile photoluminescent platforms for target-triggered sensory materials, responsive fluorescent hydrogels, and white-light-emitting phosphors.

Ultrafast assembly of swordlike Cu3(1,3,5-benzenetricarboxylate)n metal-organic framework crystals with exposed active metal sites

Owing to their large surface area and high uptake capacity, metal-organic frameworks (MOFs) have attracted considerable attention as potential materials for gas storage, energy conversion, and electrocatalysis. Various strategies have recently been proposed to manipulate the MOF surface chemistry to facilitate exposure of the embedded metal centers at the crystal surface to allow more effective binding of target molecules to these active sites. Nevertheless, such strategies remain complex, often requiring strict control over the synthesis conditions to avoid blocking pore access, reduction in crystal quality, or even collapse of the entire crystal structure. In this work, we exploit the hydrodynamics and capillary resonance associated with acoustically-driven dynamically spreading and nebulizing thin films as a new method for ultrafast synthesis of swordlike Cu₃(1,3,5-benzenetricarboxylate)_n (Cu-BTC) MOFs with unique monoclinic crystal structures (P2₁/n) distinct to that obtained via conventional bulk solvothermal synthesis, with 'swordlike' morphologies whose lengths far exceed their thicknesses. Through pulse modulation and taking advantage of the rapid solvent evaporation associated with the high nebulisation rates, we are also able to control the thicknesses of these large aspect ratio (width and length with respect to the thickness) crystals by arresting their vertical growth, which, in turn, allows exposure of the metal active sites at the crystal surface. An upshot of such active site exposure on the crystal surface is the concomitant enhancement in the conductivity of the MOF, evident from the improvement in its current density by two orders of magnitude.

High-Performance CO2-Selective Hybrid Membranes by Exploiting MOF-Breathing Effects

Conventional CO₂ separation in the petrochemical industry via cryogenic distillation or amine-based absorber-stripper units is energy-intensive and environmentally unfriendly. Membrane-based gas separation technology, in contrast, has contributed significantly to the development of energy-efficient systems for processes such as natural gas purification. The implementation of commercial polymeric membranes in gas separation processes is restricted by their permeability-selectivity trade-off and by their insufficient thermal and chemical stability. Herein, we present the fabrication of a Matrimid-based membrane loaded with a breathing metal-organic framework (MOF) (NH₂-MIL-53(Al)) which is capable of separating binary CO₂/CH₄ gas mixtures with high selectivities without sacrificing much of its CO₂ permeabilities. NH₂-MIL-53(Al) crystals were embedded in a polyimide (PI) matrix, and the mixed-matrix membranes (MMMs) were treated at elevated temperatures (up to 350 °C) in air to trigger PI cross-linking and to create PI-MOF bonds at the interface to effectively seal the grain boundary. Most importantly, the MOF transitions from its narrow-pore form to its large-pore form during this treatment, which allows the PI chains to partly penetrate the pores and cross-link with the amino functions at the pore mouth of the NH₂-MIL-53(Al) and stabilizes the open-pore form of NH₂-MIL-53(Al). This cross-linked MMM, with MOF pore entrances was made more selective by the anchored PI-chains and achieves outstanding CO₂/CH₄ selectivities. This approach provides significant advancement toward the design of selective MMMs with enhanced thermal and chemical stabilities which could also be applicable for other potential applications, such as separation of hydrocarbons (olefin/paraffin or isomers), pervaporation, and solvent-resistant nanofiltration.

The introduction of functional side groups and the application of the mixed-linker concept in divalent MIL-53(Ni) materials

Divalent MIL-53(Ni) metal–organic frameworks with 2-bromoterephthalate and terephthalate linkers feature interesting material properties as proven by various characterization techniques.

Application of Fe-based metal-organic framework and its pyrolysis products for sulfonamide treatment

The occurrence and fate of antibiotic compounds in water can adversely affect human and animal health; hence, the removal of such substrates from soil and water is indispensable. Herein, we described the synthesis method of mesoporous carbon (MPC) via the pyrolysis route from a coordination polymer Fe-based MIL-53 (or MIL-53, shortly). The MPC structure was analyzed by several physical techniques such as SEM, TEM, BET, FT-IR, VSM, and XRD. The response surface methodology (RSM) was applied to find out the effects of initial concentration, MPC dosage, and pH on the removal efficiency of trimethoprim (TMP) and sulfamethoxazole (SMX) antibiotics in water. Under the optimized conditions, the removal efficiencies of TMP and SMX were found to be 87% and 99%, respectively. Moreover, the adsorption kinetic and isotherm studies showed that chemisorption and the monolayer adsorption controlled the adsorption process. The leaching test and recyclability studies indicated that the MPC structure was stable and can be reused for at least four times without any considerable change in the removal efficiency. Plausible adsorption mechanisms were also addressed in this study. Because of high maximum adsorption capacity (85.5 mg/g and 131.6 mg/g for TMP and SMX, respectively) and efficient reusability, MPC is recommended to be a potential adsorbent for TMP and SMX from water media.

Metal-Organic Framework MIL-53(Fe) as an Adsorbent for Ibuprofen Drug Removal from Aqueous Solutions: Response Surface Modeling and Optimization

Ibuprofen contamination from water sources has been increasingly alarming due to its environmentally accumulative retention; however, the strategies for ibuprofen-containing water treatment are still an enormous challenge. Herein, we described the utilization of metal-organic frameworks MIL-53(Fe) (MIL = Materials of Institute Lavoisier) for the adsorption of ibuprofen in synthetic solution. Firstly, the MIL-53(Fe) was solvothemally synthesized and then characterized using the X-ray diffraction and Fourier-transform infrared spectroscopy techniques. The optimization of ibuprofen adsorption over MIL-53(Fe) was performed with three independent variables including ibuprofen concentration (1.6–18.4 mg/L), adsorbent dosage (0.16–1.84 g/L), and pH (2.6–9.4) according to the experimental design from response surface methodology. Under the optimized conditions, more than 80% of ibuprofen could be eliminated from water, indicating the promising potential of the MIL-53(Fe) material for treatment of this drug. Kinetic and isotherm models also were used to elucidate the chemisorption and monolayer behavior mechanisms of ibuprofen over MIL-53(Fe).

Rotational Dynamics of Linkers in Metal⁻Organic Frameworks

Among the numerous fascinating properties of metal⁻organic frameworks (MOFs), their rotational dynamics is perhaps one of the most intriguing, with clear consequences for adsorption and separation of molecules, as well as for optical and mechanical properties. A closer look at the rotational mobility in MOF linkers reveals that it is not only a considerably widespread phenomenon, but also a fairly diverse one. Still, the impact of these dynamics is often understated. In this review, we address the various mechanisms of linker rotation reported in the growing collection of literature, followed by a highlight of the methods currently used in their study, and we conclude with the impacts that such dynamics have on existing and future applications.

New functionalized MIL-53(In) solids: syntheses, characterization, sorption, and structural flexibility

The syntheses and characterization of a series of functionalized MIL-53(In) solids have been reported. Chemical groups with variations in steric hindrance and chemical nature (–(OH)₂, –Br or –NO₂ groups) were introduced through the terephthalate linker to modify the pore surface. Single crystal X-ray diffraction data, N₂ adsorption–desorption isotherms, and infrared spectra were systematically investigated to explore the impact of the functional groups grafted onto the organic linker on the dynamic behaviour of these highly flexible hybrid porous frameworks. Owing to the distinctive steric hindrance and chemical nature, the different substituents can influence the interactions between the framework and the trapped molecules, further influencing the flexibility of the materials. Dihydroxyl modified MIL-53(In) exhibits no nitrogen accessible porosity. Notably, functionalization by –Br and –NO₂ groups leads to the different capabilities of the corresponding solids to accommodate N₂ molecules.

Syntheses, characterization, sorption, and structural flexibility of new functionalized MIL-53(In) solids were fully investigated.

Nanosheets of Nonlayered Aluminum Metal-Organic Frameworks through a Surfactant-Assisted Method

During the last decade, the synthesis and application of metal-organic framework (MOF) nanosheets has received growing interest, showing unique performances for different technological applications. Despite the potential of this type of nanolamellar materials, the synthetic routes developed so far are restricted to MOFs possessing layered structures, limiting further development in this field. Here, a bottom-up surfactant-assisted synthetic approach is presented for the fabrication of nanosheets of various nonlayered MOFs, broadening the scope of MOF nanosheets application. Surfactant-assisted preorganization of the metallic precursor prior to MOF synthesis enables the manufacture of nonlayered Al-containing MOF lamellae. These MOF nanosheets are shown to exhibit a superior performance over other crystal morphologies for both chemical sensing and gas separation. As revealed by electron microscopy and diffraction, this superior performance arises from the shorter diffusion pathway in the MOF nanosheets, whose 1D channels are oriented along the shortest particle dimension.

Gas/vapour separation using ultra-microporous metal-organic frameworks: insights into the structure/separation relationship

The separation of related molecules with similar physical/chemical properties is of prime industrial importance and practically entails a substantial energy penalty, typically necessitating the operation of energy-demanding low temperature fractional distillation techniques. Certainly research efforts, in academia and industry alike, are ongoing with the main aim to develop advanced functional porous materials to be adopted as adsorbents for the effective and energy-efficient separation of various important commodities. Of special interest is the subclass of metal-organic frameworks (MOFs) with pore aperture sizes below 5-7 Å, namely ultra-microporous MOFs, which in contrast to conventional zeolites and activated carbons show great prospects for addressing key challenges in separations pertaining to energy and environmental sustainability, specifically materials for carbon capture and separation of olefin/paraffin, acetylene/ethylene, linear/branched alkanes, xenon/krypton, etc. In this tutorial review we discuss the latest developments in ultra-microporous MOF adsorbents and their use as separating agents via thermodynamics and/or kinetics and molecular sieving. Appreciably, we provide insights into the distinct microscopic mechanisms governing the resultant separation performances, and suggest a plausible correlation between the inherent structural features/topology of MOFs and the associated gas/vapour separation performance.

Emergence of Nonlinear Optical Activity by Incorporation of a Linker Carrying the p-Nitroaniline Motif in MIL-53 Frameworks

p-Nitroaniline presents the typical motif of a second-order nonlinear optically (NLO) active molecule. However, because of its crystallization in an antiparallel and hence centrosymmetric structure, the NLO activity is lost. In this contribution, the p-nitroaniline motif was built successfully into the MIL-53 metal-organic framework. More precisely, MIL-53 was synthesized with 2-amino-5-nitroterephthalate as organic linker, with Al³⁺, Ga³⁺, or In³⁺ as inorganic cation. The Al and Ga structures are polar, as confirmed by second-harmonic generation microscopy, yielding stable NLO materials. Indeed, they contain a 22-36% surplus of the dipolar 2-amino-5-nitro-terephthalate oriented in a parallel fashion. The indium compound was shown to be less crystalline and centrosymmetric. Ab initio modeling of the second-order NLO response shows that the Al and Ga materials show a response comparable to typical inorganic commercial NLO materials such as KDP. As a hybrid material, capable of low-temperature synthesis and processing and the ultrafast NLO responses associated with organic materials, this material can potentially provide an interesting venue for applications with respect to traditional inorganic NLO materials.

Gas Phase Sensing of Alcohols by Metal Organic Framework-Polymer Composite Materials

Affinity layers play a crucial role in chemical sensors for the selective and sensitive detection of analytes. Here, we report the use of composite affinity layers containing Metal Organic Frameworks (MOFs) in a polymeric matrix for sensing purposes. Nanoparticles of NH₂-MIL-53(Al) were dispersed in a Matrimid polymer matrix with different weight ratios (0-100 wt %) and drop-casted on planar capacitive transducer devices. These coated devices were electrically analyzed using impedance spectroscopy and investigated for their sensing properties toward the detection of a series of alcohols and water in the gas phase. The measurements indicated a reversible and reproducible response in all devices. Sensor devices containing 40 wt % NH₂-MIL-53(Al) in Matrimid showed a maximum response for methanol and water. The sensor response time slowed down with increasing MOF concentration until 40 wt %. The half time of saturation response (τ_0.5) increased by ∼1.75 times for the 40 wt % composition compared to devices coated with Matrimid only. This is attributed to polymer rigidification near the MOF/polymer interface. Higher MOF loadings (≥50 wt %) resulted in brittle coatings with a response similar to the 100 wt % MOF coating. Cross-sensitivity studies showed the ability to kinetically distinguish between the different alcohols with a faster response for methanol and water compared to ethanol and 2-propanol. The observed higher affinity of the pure Matrimid polymer toward methanol compared to water allows also for a higher uptake of methanol in the composite matrices. Also, as indicated by the sensing studies with a mixture of water and methanol, the methanol uptake is independent of the presence of water up to 6000 ppm of water. The NH₂-MIL-53(Al) MOFs dispersed in the Matrimid matrix show a sensitive and reversible capacitive response, even in the presence of water. By tuning the precise compositions, the affinity kinetics and overall affinity can be tuned, showing the promise of this type of chemical sensors.

Breathing-induced new phase transition in an MIL-53(Al)–NH2 metal–organic framework under high methane pressures

The room temperature methane sorption tests on a flexible MOF reveal a new phase transition to a large pore phase above 45 bar, which is helpful to increase the deliverable capacity for natural gas storage.

Deducing CO2 motion, adsorption locations and binding strengths in a flexible metal-organic framework without open metal sites

Microporous metal-organic frameworks (MOFs) have high surface areas and porosities, and are well-suited for CO2 capture. MIL-53 features corner-sharing MO4(OH)2 (M = Al, Ga, Cr, etc.) octahedra interconnected by benzenedicarboxylate linkers that form one-dimensional rhombic tunnels, and exhibits an excellent adsorption ability for guest molecules such as CO2. Studying the behavior of adsorbed CO2 in MIL-53 via solid-state NMR (SSNMR) provides rich information on the dynamic motion of guest molecules as well as their binding strengths to the MOF host, and sheds light on the specific guest adsorption mechanisms. Variable-temperature (13)C SSNMR spectra of (13)CO2 adsorbed within various forms of MIL-53 are acquired and analyzed. CO2 undergoes a combination of two motions within MIL-53; we report the types of motion present, their rates, and rotational angles. (1)H-(13)C CP SSNMR experiments are used to examine the proximity of (1)H atoms in the MOF to (13)C atoms in CO2 guests. By replacing (1)H with (2)H in MIL-53, the location of the CO2 adsorption site in MIL-53 is experimentally confirmed by (1)H-(13)C CP SSNMR. The binding strength of CO2 within these MIL-53 MOFs follows the order MIL-53-NH2 (Al) > MIL-53-NH2 (Ga) > MIL-53 (Al) > MIL-53 (Ga).

Metal Organic Framework Crystals in Mixed-Matrix Membranes: Impact of the Filler Morphology on the Gas Separation Performance

Mixed-matrix membranes (MMMs) comprising NH2-MIL-53(Al) and Matrimid® or 6FDA-DAM have been investigated. The MOF loading has been varied between 5 and 20 wt%, while NH2-MIL-53(Al) with three different morphologies: nanoparticles, nanorods and microneedles have been dispersed in Matrimid®. The synthesized membranes have been tested in the separation of CO2 from CH4 in an equimolar mixture. At 3 bar and 298 K for 8 wt% MOF loading, incorporation of NH2-MIL-53(Al) nanoparticles leads to the largest improvement compared to nanorods and microneedles. The incorporation of the best performing filler, i.e. NH2-MIL-53(Al) nanoparticles, to the highly permeable 6FDA-DAM has a larger effect, and the CO2 permeability increased up to 85 % with slightly lower selectivities for 20 wt% MOF loading. Specifically, these membranes have a permeability of 660 Barrer with CO2/CH4 separation factor of 28, leading to a performance very close to the Robeson limit of 2008. Furthermore, a new non-destructive technique based on Raman spectroscopy mapping is introduced to assess the homogeneity of the filler dispersion in the polymer matrix. The MOF contribution can be calculated by modelling the spectra. The determined homogeneity of the MOF filler distribution in the polymer is confirmed by FIB-SEM analysis.

Surface modification route to prepare novel polyamide@NH2_MIL-88B nanocomposite membranes for water treatment

A surface modification route is used to fabricate a novel PA nanocomposite membrane with a PA coating on a NH₂_MIL-88B interlayer.

CO2 capture under humid conditions in NH2-MIL-53(Al): the influence of the amine functional group

NH₂-MIL-53(Al) exhibited a considerable stronger affinity to water than MIL-53(Al). Thus, the hydrophobicity (shown by in situ FTIR) of the pores within MIL-53(Al) enhanced the CO₂ adsorption.

Covalent immobilization of glucose oxidase on amino MOFs via post-synthetic modification

Post Synthetic Modification (PSM) of amino-metal organic frameworks (NH₂-MOFs) with the enzyme Glucose Oxidase (GOx) is reported.

An advanced approach for measuring acidity of hydroxyls in confined space: a FTIR study of low-temperature CO and (15)N2 adsorption on MOF samples from the MIL-53(Al) series

Acidity of solids is decisive for their interaction with guest molecules. One of the most used methods for measuring the acidity of surface hydroxyl groups is the hydrogen bond method based on the spectral shift of the OH stretching modes induced by the adsorption of weak bases. However, many materials of practical interest (e.g. metal organic frameworks, zeolites, etc.) are porous and the OH groups are involved in H-bonding with framework basic sites. Here we show that MIL-53(Al) and NH2-MIL-53(Al) samples are characterized by one type of structural hydroxyl but three IR bands are detected at 100 K with these materials (at 3721, 3711 and 3683 cm(-1)). These bands are assigned to structural hydroxyls involved in H-bonding with different strengths. There is no correlation between the acidities of the hydroxyls, as measured by low-temperature CO or (15)N2 adsorption, and the main reason for this is the pre-existing H-bond. A method for the estimation of the intrinsic frequency of the OH groups (i.e. if not participating in H-bonds), based on the analysis of the spectral data obtained with two molecular probes, is proposed. According to this method, the OH stretching frequency of the structural hydroxyls of MIL-53(Al) samples is determined to be 3727 cm(-1). The formation of 1 : 1 adducts between the hydroxyls and strong bases leads to breaking of the pre-existing H-bonds. When the base is weak, bifurcated complexes are formed which slightly affects the spectral shift. The conclusions derived here considerably broaden the applicability of the H-bond method for assessing protonic acidity of materials and systems where the OH groups are preliminarily involved in H-bonding.

Experimental Evidence of Negative Linear Compressibility in the MIL-53 Metal-Organic Framework Family

We report a series of powder X-ray diffraction experiments performed on the soft porous crystals MIL-53(Al) and NH2-MIL-53(Al) in a diamond anvil cell under different pressurization media. Systematic refinements of the obtained powder patterns demonstrate that these materials expand along a specific direction while undergoing total volume reduction under an increase in hydrostatic pressure. The results confirm for the first time the Negative Linear Compressibility behaviour of this family of materials recently predicted from quantum chemical calculations.

Crystallographic studies of gas sorption in metal-organic frameworks

Metal-organic frameworks (MOFs) are a class of porous crystalline materials of modular design. One of the primary applications of these materials is in the adsorption and separation of gases, with potential benefits to the energy, transport and medical sectors. In situ crystallography of MOFs under gas atmospheres has enabled the behaviour of the frameworks under gas loading to be investigated and has established the precise location of adsorbed gas molecules in a significant number of MOFs. This article reviews progress in such crystallographic studies, which has taken place over the past decade, but has its origins in earlier studies of zeolites, clathrates etc. The review considers studies by single-crystal or powder diffraction using either X-rays or neutrons. Features of MOFs that strongly affect gas sorption behaviour are discussed in the context of in situ crystallographic studies, specifically framework flexibility, and the presence of (organic) functional groups and unsaturated (open) metal sites within pores that can form specific interactions with gas molecules.