Tribological testing of skin products: gender, age, and ethnicity on the volar forearm

Human Head and Helmet Interface Friction Coefficients with Biological Sex and Hair Property Comparisons

Dummy headforms used for impact testing have changed little over the years, and frictional characteristics are thought not to represent the human head accurately. The frictional interface between the helmet and head is an essential factor affecting impact response. However, few studies have evaluated the coefficient of friction (COF) between the human head and helmet surface. This study's objectives were to quantify the human head's static and dynamic COF and evaluate the effect of biological sex and hair properties. Seventy-four participants slid their heads along a piece of helmet foam backed by a fixed load cell at varying normal force levels. As normal force increased, static and dynamic human head COF decreased following power-law curves. At 80 N, the static COF is 0.32 (95% CI 0.30-0.34), and the dynamic friction coefficient is 0.27 (95% CI 0.26-0.28). Biological sex and hair properties were determined not to affect human head COF. The COFs between the head and helmet surface should be used to develop more biofidelic head impact testing methods, define boundary conditions for computer simulations, and aid decision-making for helmet designs.

Effect of massage on retinol skin penetration

Topical administration of active substances may be promoted by optimizing not only the vehicle formulation but also the application protocol. The formulation aspects are widely studied in the literature while a few works are dedicated to the development of application methods. In this context, we studied an application protocol usable as a part of skincare routine by investigating the effect of massage on the skin penetration of retinol. Retinol is a lipophilic molecule widely used as an anti-ageing firming agent in cosmetic formulations. Massage was applied to pig skin explants mounted to Franz diffusion cells after or before the deposit of the retinol-loaded formulation. Thetype of skin massage (roll or rotary type) and its duration were varied.The massage protocol had a significant influence on retinol skin penetration. Due to its highly lipophilic character, retinol accumulated into the stratum corneum but, depending on the massage protocol, a significant retinol concentration was obtained after 4 hours in epidermis and dermis layers. Results showed that the roll-type massage was significantly more efficient than the rotary process that exhibited little effect on retinol cutaneous penetration. Such results could be interesting for the development of massage devices in association with cosmetic formulations.

Friction properties of in vivo human skin from visualized friction testing

Investigations on mechanical behaviors of intravital human skin are of significance in various fields. However, due to the great complexity and the individual variation of human skin, traditional experimental mechanics often fails to work in such research objects. In this study, the friction property considering the skin-uplift effect of human skin was in vivo studied experimentally and theoretically. An in situ and noninvasive friction experiment was performed in vivo on human skin, where the projected contact morphology was captured through a novel specially developed optical system. According to the contact morphology, a model taking uplift resistance into account is proposed based on Greenwood model, in which the contact area was depicted as a combination of two ellipses to better characterize the skin deformation. Moreover, since the model degrades into Greenwood model in small deformation, it can be considered as an extension from the perspective of small deformation to large deformation. Based on the model, the adhesion friction and deformation friction have been separated according to the ratio of indentation depth to probe radius. The results show that the friction property of skin varies with the indentation depth changing, and the deformation friction is positively correlated with the ratio of indentation depth to probe radius.

Interpersonal differences in the friction response of skin relate to FTIR measures for skin lipids and hydration

Understanding the mechanical response of skin to contact is of importance when developing products that interact with the skin. The shear forces that arise due to friction in the interface are a key aspect of skin interactions, because shear is known to contribute to discomfort and tissue injury. However, the frictional response of skin shows large variations between people. It has been hypothesised that these variations relate to differences between people in the physiological properties of their skin, but the underlying mechanisms are not well understood. In order to gain new insights into these interpersonal differences in friction behaviour, in vivo FTIR measurements and in vivo friction measurements were performed on the same patch of skin. Quantitative analysis of the various peaks in the FTIR spectra provided information on the moisture content of the stratum corneum and the amount and mechanical properties of the lipids on the skin. The lipid viscosity, as characterised by the width of the 2920 cm^-1 peak, correlates with the friction, whilst, interestingly, no relationship was found between the quantity of lipids on the skin surface and the coefficient of friction. Additionally, and as expected, a fairly strong correlation was obtained between the moisture content, as characterised by the height of the Amide I peak and the coefficient of friction. The presented results show that spectroscopy techniques can be used in as a non-invasive method to identify people who may show elevated levels of friction and thus are at increased risk of developing shear induced tissue injury.

Guidelines for designing a realistic peripheral venous catheter insertion simulator: A literature review

A literature review was conducted to develop more realistic medical simulators that better prepare aspiring health professionals to perform a medical procedure in vivo. Thus, this review proposes an approach that might assist researchers design improved medical simulators, particularly new materials that would enhance the sensation of touch for skin substitutes. By targeting the current needs in the field of simulation learning, we concluded that peripheral venous catheter insertion simulators lack realistic haptic feedback. Enhanced peripheral venous catheter insertion simulators will accelerate the mastery of the medical procedure, thus decreasing the number of failures in patients and costs related to this procedure.

Evaluation of the head-helmet sliding properties in an impact test

The scalp plays a crucial role in head impact biomechanics, being the first tissue involved in the impact and providing a sliding interface between the impactor and/or helmet and the skull. It is important to understand both the scalp-skull and the scalp-helmet sliding in order to determine the head response due to an impact. However, experimental data on the sliding properties of the scalp is lacking. The aim of this work was to identify the sliding properties of the scalp using cadaver heads, in terms of scalp-skull and scalp-liner (internal liner of the helmet) friction and to compare these values with that of widely used artificial headforms (HIII and magnesium EN960). The effect of the hair, the direction of sliding, the speed of the test and the normal load were considered. The experiments revealed that the sliding behaviour of the scalp under impact loading is characterised by three main phases: (1) the low friction sliding of the scalp over the skull (scalp-skull friction), (2) the tensioning effect of the scalp and (3) the sliding of the liner fabric over the scalp (scalp-liner friction). Results showed that the scalp-skull coefficient of friction (COF) is very low (0.06 ± 0.048), whereas the scalp-liner COF is 0.29 ± 0.07. The scalp-liner COF is statistically different from the value of the HIII-liner (0.75 ± 0.06) and the magnesium EN960-liner (0.16 ± 0.026). These data will lead to the improvement of current headforms for head impact standard tests, ultimately leading to more realistic head impact simulations and the optimization of helmet designs.

A tribo-mechanical analysis of PVA-based building-blocks for implementation in a 2-layered skin model

Poly(vinyl) alcohol hydrogel (PVA) is a well-known polymer widely used in the medical field due to its biocompatibility properties and easy manufacturing. In this work, the tribo-mechanical properties of PVA-based blocks are studied to evaluate their suitability as a part of a structure simulating the length scale dependence of human skin. Thus, blocks of pure PVA and PVA mixed with Cellulose (PVA-Cel) were synthesised via freezing/thawing cycles and their mechanical properties were determined by Dynamic Mechanical Analysis (DMA) and creep tests. The dynamic tests addressed to elastic moduli between 38 and 50kPa for the PVA and PVA-Cel, respectively. The fitting of the creep compliance tests in the SLS model confirmed the viscoelastic behaviour of the samples with retardation times of 23 and 16 seconds for the PVA and PVA-Cel, respectively. Micro indentation tests were also achieved and the results indicated elastic moduli in the same range of the dynamic tests. Specifically, values between 45-55 and 56-81kPa were obtained for the PVA and PVA-Cel samples, respectively. The tribological results indicated values of 0.55 at low forces for the PVA decreasing to 0.13 at higher forces. The PVA-Cel blocks showed lower friction even at low forces with values between 0.2 and 0.07. The implementation of these building blocks in the design of a 2-layered skin model (2LSM) is also presented in this work. The 2LSM was stamped with four different textures and their surface properties were evaluated. The hydration of the 2LSM was also evaluated with a corneometer and the results indicated a gradient of hydration comparable to the human skin.

In vitro investigation of skin damage due to microscale shearing

Despite several studies dealing with the mechanical and tribological properties of skin, the majority of these investigations have been performed at macroscopic levels. However, because of the multilayer structure of skin, it is necessary to perform studies at microscopic scales to reveal the effect of individual layer constituents on the overall skin response to mechanical stimuli. To bridge the gap in knowledge of the micromechanical behavior of skin, a custom-made mechanical tester, optical microscopy, and cross-sectional histology were used to examine the deformation and tribological behavior of porcine skin subjected to various normal and shear loadings. Representative friction and wear results of skin tested under unidirectional and reciprocating (cyclic) shearing (scratching) conditions are interpreted in terms of the scratching speed, normal load, and number of scratch cycles to illustrate the effects of stratum corneum, cellular epidermis, and dermis on the friction and wear characteristics of skin. Depending on the normal load and scratch time (cycles), different friction mechanisms (i.e., adhesion, plowing, and squeeze-film lubrication) and wear mechanisms (i.e., surface plasticity/plowing, bulk shearing, cohesive failure, tearing, and delamination) were found to control shear-induced skin damage. The results of this study provide insight into microscale friction and wear processes influencing the mechanical response of skin subjected to normal and shear surface tractions.

A comparison of two methods of measuring static coefficient of friction at low normal forces: a pilot study

This study compares two methods for estimating static friction coefficients for skin. In the first method, referred to as the 'tilt method', a hand supporting a flat object is tilted until the object slides. The friction coefficient is estimated as the tangent of the angle of the object at the slip. The second method estimates the friction coefficient as the pull force required to begin moving a flat object over the surface of the hand, divided by object weight. Both methods were used to estimate friction coefficients for 12 subjects and three materials (cardboard, aluminium, rubber) against a flat hand and against fingertips. No differences in static friction coefficients were found between the two methods, except for that of rubber, where friction coefficient was 11% greater for the tilt method. As with previous studies, the friction coefficients varied with contact force and contact area. Static friction coefficient data are needed for analysis and design of objects that are grasped or manipulated with the hand. The tilt method described in this study can easily be used by ergonomic practitioners to estimate static friction coefficients in the field in a timely manner.

Influence of epidermal hydration on the friction of human skin against textiles

Friction and shear forces, as well as moisture between the human skin and textiles are critical factors in the formation of skin injuries such as blisters, abrasions and decubitus. This study investigated how epidermal hydration affects the friction between skin and textiles.The friction between the inner forearm and a hospital fabric was measured in the natural skin condition and in different hydration states using a force plate. Eleven males and eleven females rubbed their forearm against the textile on the force plate using defined normal loads and friction movements. Skin hydration and viscoelasticity were assessed by corneometry and the suction chamber method, respectively.In each individual, a highly positive linear correlation was found between skin moisture and friction coefficient (COF). No correlation was observed between moisture and elasticity, as well as between elasticity and friction. Skin viscoelasticity was comparable for women and men. The friction of female skin showed significantly higher moisture sensitivity. COFs increased typically by 43% (women) and 26% (men) when skin hydration varied between very dry and normally moist skin. The COFs between skin and completely wet fabric were more than twofold higher than the values for natural skin rubbed on a dry textile surface.Increasing skin hydration seems to cause gender-specific changes in the mechanical properties and/or surface topography of human skin, leading to skin softening and increased real contact area and adhesion.

Textiles and Human Skin, Microclimate, Cutaneous Reactions: An Overview

This article overviews research in the interdisciplinary area of textile/skin interaction and related cutaneous intolerance. Microclimate in the skin/clothing system and especially the skin responses relates to the moisture and heat transfer within this system and plays a critical role in skin irritation from textiles. A discussion is then given on skin irritation reactions to textiles, including intolerance caused by chemicals (dyes and finishes) and physical contact/friction. Finally, two skin injuries, blisters and pressure ulcers, which are caused by physical contact, pressure, and friction, are documented. Despite the prevalent problems caused by ill textile/skin interactions, minimal efforts have been devoted to this field. In addition, the in vivo experimental studies infrequently lead to a solid conclusion. The cause may lie in the dramatic variation of skin conditions among individuals as well as among different anatomic sites of the same person. Another reason might be the lack of communications between researchers in the areas of textiles and dermatology.

A Technique to Determine Friction at the Fingertips

This article proposes a technique to calculate the coefficient of friction for the fingertip– object interface. Twelve subjects (6 males and 6 females) participated in two experiments. During the first experiment (the imposed displacement method), a 3-D force sensor was moved horizontally while the subjects applied a specified normal force (4 N, 8 N, 12 N) on the surface of a sensor covered with different materials (sandpaper, cotton, rayon, polyester, and silk).Thenormal forceand thetangential force(i.e., the force due to the sensor motion) were recorded. Thecoefficient of friction(µd) was calculated as the ratio between the tangential force and the normal force. In the second experiment (the beginning slip method), a small instrumented object was gripped between the index finger and the thumb, held stationary in the air, and then allowed to drop. The weight (200 g, 500 g, and 1,000 g) and the surface (sandpaper, cotton, rayon, polyester, and silk) in contact with the digits varied across trials. The same sensor as in the first experiment was used to record thenormal force(in a horizontal direction) and thetangential force(in the vertical direction). Theslip force(i.e., the minimal normal force or grip force necessary to prevent slipping) was estimated as the force at the moment when the object just began to slip. The coefficient of friction was calculated as the ratio between the tangential force and the slip force. The results show that (1) the imposed displacement method is reliable; (2) except sandpaper, for all other materials the coefficient of friction did not depend on the normal force; (3) theskin–sandpapercoefficient of friction was the highest µd= 0.96 ± 0.09 (for 4-N normal force) and theskin–rayonrayon coefficient of friction was the smallest µd= 0.36 ± 0.10; (4) no significant difference between the coefficients of friction determined with the imposed displacement method and the beginning slip method was observed. We view the imposed displacement technique as having an advantage as compared with the beginning slip method, which is more cumbersome (e.g., dropped object should be protected from impacts) and prone to subjective errors owing to the uncertainty in determining the instance of the slip initiation (i.e., impeding sliding).

Barefoot-pedestrian tribometry: in vivo method of measurement of available friction between the human heel and the walkway

We have developed an in vivo tribometer for characterizing the friction of a human heel against a planar test surface. The pedestrian steps down on an angled test surface and an observer determines if the person's heel slips. In the simplest variation, the subject simply steps down onto the test surface. The second variation has the standing subject's lower leg constrained to a vertically running carriage, forcing the pedestrian's leg to descend vertically. The third variation has the subject sitting, with an operator raising and lowering the carriage to which the leg is attached. The test surface was fixed at a given angle, a set of repeated tests was run, and the number of tests and slips were recorded. The test-surface angle was incremented through a range that varied from no slips to all slips. We analyzed the data using logistic regression. We found that the unconstrained test subject's logistic-regression curves varied greatly from subject to subject. The standing, constrained subjects were significantly closer to each other, but at the expense of a much higher spread of the angular range. The seated, constrained test subject's results were both extremely close and had extremely low angular spread.

Skin friction blistering: computer model

BACKGROUND/PURPOSE

Friction blisters, a common injury in sports and military operations, can adversely effect or even halt performance. Given its frequency and hazardous nature, recent research efforts appear limited. Blistering can be treated as a delamination phenomenon; similar issues in materials science have been extensively investigated in theory and experiment. An obstacle in studying blistering is the difficulty of conducting experiment on humans and animals. Computer modeling thus becomes a preferred tool.

METHOD

This paper used a dynamic non-linear finite-element model with a blister-characterized structure and contact algorithm for outer materials and blister roof to investigate the effects on deformation and stress of an existing blister by changing the friction coefficient and elastic modulus of the material in contact with the blister.

RESULTS

Through the dynamics mode and harmonic frequency approach, we demonstrated that the loading frequency leads to dramatic changes of displacement and stress in spite of otherwise similar loading. Our simulations show that an increased friction coefficient does not necessarily result in an increase in either the stress on the hot spot or blister deformation; local maximum friction stress and Von Mises stress exist for some friction coefficients over the wide range examined here. In addition, the stiffness of contact material on blistering is also investigated, and no significant effects on deformation and Von Mises stress are found, again at the range used. The model and method provided here may be useful for evaluating loading environments and contact materials in reducing blistering incidents.

CONCLUSION

The coupling finite-element model can predict the effects of friction coefficient and contacting materials&apos stiffness on blister deformation and hot spot stress.