Revealing How Topography of Surface Microstructures Alters Capillary Spreading

Azimuthal Variation of Apparent Contact Angles on Structured Surfaces Featuring Micrometric Ramps, Pyramids and Staggered Cubes at Two Different Inherent Wettabilities

As new manufacturing methods enable manufacturing of microstructured surfaces with varying structure geometries, questions remain on some effects on the wetting behavior and the resulting apparent contact angles. In this study, we report the manufacturing process using 3D Direct Laser Writing (3D-DLW) and hot embossing for Poly methyl methacrylate (PMMA) surfaces with micrometric pyramids, cubes on a staggered grid and two types of ramped structures. We measure the azimuthal variation of the apparent contact angle of sessile droplets on the surfaces. Using plasma polymerization or no treatment of the surfaces, two different inherent wettabilities are studied. We find that while all structure types cause an azimuthal variation of the apparent contact angle, pinning at the ramp tops increases the contact angle more strongly on one side. On pyramid structures, pinning lines can occur on the structure axes and diagonals similarly. For cubes on a hexagonal grid, the strongest contact angle increases are observed along the primary structure axes, where pinning is preferred while smaller peaks are seen on the secondary axes at 60 and 120° to the primary axis.

Modulation of the Capillary Force Profile at the Solid-Solid Interface through Topographical Modifications

Modulations of interfacial adhesion at solid-solid contacts are desired in many multidisciplinary applications. This study aims at the creation of reproducible solid-solid interfaces with significantly mitigated capillary adhesion through physical modifications. First, a continuum boundary element-based mathematical model to predict capillary forces at solid-solid contacts was developed and validated. Next, the model was utilized to simulate the capillary adhesion between a glass substrate with hypothetical surface topographies, in the form of nanopillars and nanowells, and silica particles of various sizes at varied humidity conditions. This study revealed that the nanopillar surface topography was much more effective than the nanowell in suppressing the capillary condensation and could lower the capillary forces by more than one order of magnitude for the micrometer-scale and nanoscale particulates. This study suggested that topographical tuning at the solid-solid interface can significantly reduce interfacial adhesion and promote the dust-resistance characteristic of a substrate. Finally, this simulation study can guide the fabrication of solid surfaces with reproducible topography and optimized geometrical parameters to yield an extremely reduced interfacial capillary adhesion.

Interaction between honeybee mandibles and propolis

In a biomimetic top-down process, challenging the problem of resin deposition on woodworking machine tools, an adequate biological model was sought, which hypothetically could have developed evolutionary anti-adhesive strategies. The honeybee (Apis mellifera) was identified as an analogue model since it collects and processes propolis, which largely consists of collected tree resin. Propolis is a sticky substance used by bees to seal their hive and protect the colony against pathogens. In spite of its stickiness, honeybees are able to handle and manipulate propolis with their mandibles. We wanted to know if beneficial anti-adhesive properties of bee mandibles reduce propolis adhesion. The anatomy of bee mandibles was studied in a (cryo-)scanning electron microscope. Adhesion experiments were performed with propolis on bee mandibles to find out if bee mandibles have anti-adhesive properties that enable bees to handle the sticky material. A scale-like pattern was found on the inside of the mandible. Fresh mandibles were covered with a seemingly fluid substance that was at least partially removed during the washing process. Propolis adhesion on bee mandibles was measured to be 1 J/m² and was indeed significantly lower compared to five technical materials. Propolis adhesion was higher on mandibles that were washed compared to fresh, unwashed mandibles. Results indicate that the medial surface of the mandible is covered with a fluid substance that reduces propolis adhesion. First results suggested that the surface pattern does do not have a direct effect on propolis adhesion.

Vibration sorting of small droplets on hydrophilic surface by asymmetric contact-line friction

Droplet spreading and transport phenomenon is ubiquitous and has been studied by engineered surfaces with a variety of topographic features. To obtain a directional bias in dynamic wetting, hydrophobic surfaces with a geometrical asymmetry are generally used, attributing the directionality to one-sided pinning. Although the pinning may be useful for directional wetting, it usually limits the droplet mobility, especially for small volumes and over wettable surfaces. Here, we demonstrate a pinning-less approach to rapidly transport millimeter sized droplets on a partially wetting surface. Placing droplets on an asymmetrically structured surfaces with micron-scale roughness and applying symmetric horizontal vibration, they travel rapidly in one direction without pinning. The key, here, is to generate capillary-driven rapid contact-line motion within the time-scale of period of vibration. At the right regime where a friction factor local at the contact line dominates the rapid capillary motion, the asymmetric surface geometry can induce smooth and continuous contact-line movement back and forth at different speed, realizing directional motion of droplets even with small volumes over the wettable surface. We found that the translational speed is selective and strongly dependent on the droplet volume, oscillation frequency, and surface pattern properties, and thus droplets with a specific volume can be efficiently sorted out.

Droplet Impact on Surfaces with Asymmetric Microscopic Features

The impact of liquid drops on a rigid surface is central in cleaning, cooling, and coating processes in both nature and industrial applications. However, it is not clear how details of pores, roughness, and texture on the solid surface influence the initial stages of the impact dynamics. Here, we experimentally study drops impacting at low velocities onto surfaces textured with asymmetric (tilted) ridges. We found that the difference between impact velocity and the capillary speed on a solid surface is a key factor of spreading asymmetry, where the capillary speed is determined by the friction at a moving three-phase contact line. The line-friction capillary number Ca_f = μ_fV₀/σ (where μ_f,V₀, and σ are the line friction, impact velocity, and surface tension, respectively) is defined as a measure of the importance of the topology of surface textures for the dynamics of droplet impact. We show that when Ca_f ≪ 1, the droplet impact is asymmetric; the contact line speed in the direction against the inclination of the ridges is set by line friction, whereas in the direction with inclination, the contact line is pinned at acute corners of the ridges. When Ca_f ≫ 1, the geometric details of nonsmooth surfaces play little role.

Modulating the foreign body response of implants for diabetes treatment

Diabetes Mellitus is a group of diseases characterized by high blood glucose levels due to patients' inability to produce sufficient insulin. Current interventions often require implants that can detect and correct high blood glucose levels with minimal patient intervention. However, these implantable technologies have not reached their full potential in vivo due to the foreign body response and subsequent development of fibrosis. Therefore, for long-term function of implants, modulating the initial immune response is crucial in preventing the activation and progression of the immune cascade. This review discusses the different molecular mechanisms and cellular interactions involved in the activation and progression of foreign body response (FBR) and fibrosis, specifically for implants used in diabetes. We also highlight the various strategies and techniques that have been used for immunomodulation and prevention of fibrosis. We investigate how these general strategies have been applied to implants used for the treatment of diabetes, offering insights on how these devices can be further modified to circumvent FBR and fibrosis.

Droplet leaping governs microstructured surface wetting

Microstructured surfaces that control the direction of liquid transport are not only ubiquitous in nature, but they are also central to technological processes such as fog/water harvesting, oil-water separation, and surface lubrication. However, a fundamental understanding of the initial wetting dynamics of liquids spreading on such surfaces is lacking. Here, we show that three regimes govern microstructured surface wetting on short time scales: spread, stick, and contact line leaping. The latter involves establishing a new contact line downstream of the wetting front as the liquid leaps over specific sections of the solid surface. Experimental and numerical investigations reveal how different regimes emerge in different flow directions during wetting of periodic asymmetrically microstructured surfaces. These insights improve our understanding of rapid wetting in droplet impact, splashing, and wetting of vibrating surfaces and may contribute to advances in designing structured surfaces for the mentioned applications.

The Effect of Surface Roughness on the Contact Line and Splashing Dynamics of Impacting Droplets

Whether a droplet splashes upon impact onto a solid is known to depend not only on the fluid properties and its speed, but also on the substrate characteristics. Past research has shown that splashing is heavily influenced by the substrate roughness. Indeed, in this manuscript, we demonstrate that splashing is ruled by the surface roughness, the splashing ratio, and the dynamic contact angle. Experiments consist of water and ethanol droplets impacting onto solid substrates with varying degrees of roughness. High speed imaging is used to extract the dynamic contact angle as a function of the spreading speed for these impacting droplets. During the spreading phase, the dynamic contact angle achieves an asymptotic maximum value, which depends on the substrate roughness and the liquid properties. We found that this maximum dynamic contact angle, together with the liquid properties, the ratio of the peak to peak roughness and the surface feature mean width, determines the splashing to no-splashing threshold. In addition, these parameters consistently differentiate the splashing behaviour of impacts onto smooth hydrophilic, hydrophobic and superhydrophobic surfaces.