Structural Evolution of Chemically-Driven RuO2 Nanowires and 3-Dimensional Design for Photo-Catalytic Applications

Plasma-Deposited Ru-Based Thin Films for Photoelectrochemical Water Splitting

Plasma-enhanced chemical vapor deposition (PECVD) was used to produce new Ru-based thin catalytic films. The surface molecular structure of the films was examined by X-ray photoelectron spectroscopy (XPS). To determine the electro- and photoelectrochemical properties, the oxygen evolution reaction (OER) process was investigated by linear sweep voltammetry (LSV) at pH = 13.6. It was found that Ru atoms were mainly in the metallic state (Ru0) in the as-deposited films, whereas after the electrochemical stabilization, higher oxidation states, mainly Ru+4 (RuO2), were formed. The stabilized films exhibited high catalytic activity in OER—for the electrochemical process, the onset and η10 overpotentials were approx. 220 and 350 mV, respectively, while for the photoelectrochemical process, the pure photocurrent density of about 160 mA/cm2 mg was achieved at 1.6 V (vs. reversible hydrogen electrode (RHE)). The plasma-deposited RuOX catalyst appears to be an interesting candidate for photoanode material for photoelectrochemical (PEC) water splitting.

An Efficient Electrochemical Sensor Driven by Hierarchical Hetero-Nanostructures Consisting of RuO2 Nanorods on WO3 Nanofibers for Detecting Biologically Relevant Molecules

By means of electrospinning with the thermal annealing process, we investigate a highly efficient sensing platform driven by a hierarchical hetero-nanostructure for the sensitive detection of biologically relevant molecules, consisting of single crystalline ruthenium dioxide nanorods (RuO₂ NRs) directly grown on the surface of electrospun tungsten trioxide nanofibers (WO₃ NFs). Electrochemical measurements reveal the enhanced electron transfer kinetics at the prepared RuO₂ NRs-WO₃ NFs hetero-nanostructures due to the incorporation of conductive RuO₂ NRs nanostructures with a high surface area, resulting in improved relevant electrochemical sensing performances for detecting H₂O₂ and L-ascorbic acid with high sensitivity.

Synthesis of Pd/Ru Bimetallic Nanoparticles by Escherichia coli and Potential as a Catalyst for Upgrading 5-Hydroxymethyl Furfural Into Liquid Fuel Precursors

Escherichia coli cells support the nucleation and growth of ruthenium and ruthenium-palladium nanoparticles (Bio-Ru and Bio-Pd/Ru NPs). We report a method for the synthesis of these monometallic and bimetallic NPs and their application in the catalytic upgrading of 5-hydroxymethyl furfural (5-HMF) to 2,5 dimethylfuran (DMF). Examination using high resolution transmission electron microscopy with energy dispersive X-ray microanalysis (EDX) and high angle annular dark field (HAADF) showed Ru NPs located mainly at the cell surface using Ru(III) alone but small intracellular Ru-NPs (size ∼1-2 nm) were visible only in cells that had been pre-"seeded" with Pd(0) (5 wt%) and loaded with equimolar Ru. Pd(0) NPs were distributed between the cytoplasm and cell surface. Cells bearing 5% Pd/5% Ru showed some co-localization of Pd and Ru but chance associations were not ruled out. Cells loaded to 5 wt% Pd/20 wt% Ru showed evidence of core-shell structures (Ru core, Pd shell). Examination of this cell surface material using X-ray photoelectron spectroscopy (XPS) showed Pd(0) and Pd(II) and Ru(IV) and Ru(III), with confirmation by analysis of bulk material using X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) analyses. Both Bio-Ru NPs and Bio-Pd/Ru NPs were active in the conversion of 5-HMF into 2,5-DMF but commercial Ru on carbon catalyst outperformed 5 wt% bio-Ru by fourfold. While 5 wt% Pd/20 wt% Ru achieved 20% yield of DMF the performance of the 5 wt% Pd/5 wt% Ru bio-catalyst was higher and comparable to the commercial 5 wt% Ru/C catalyst in a test reaction using commercial 5-HMF (>50% selectivity). 5-HMF was prepared by thermochemical hydrolysis of starch and cellulose with solvent extraction of 5-HMF into methyltetrahydrofuran (MTHF). Here, with MTHF as the reaction solvent the commercial Ru/C catalyst had little activity (100% conversion, negligible selectivity to DMF) whereas the 5 wt% Pd/5 wt% Ru bio-bimetallic gave 100% conversion and 14% selectivity to DMF from material extracted from hydrolyzates. The results indicate a potential green method for realizing increased energy potential from biomass wastes as well as showing a bio-based pathway to manufacturing a scarcely described bimetallic material.

Electroless deposition of RuO2-based nanoparticles for energy conversion applications

The core/shell VO_x·mH₂O/RuO₂·nH₂O, synthesized by simply immersing VOx·mH₂O into RuCl₃ solution, shows a better catalytic activity of ORR than RuO₂·nH₂O.

Unidirectional growth of single crystalline β-Na0.33V2O5and α-V2O5nanowires driven by controlling the pH of aqueous solution and their electrochemical performances for Na-ion batteries

Single crystalline β-Na_0.33V₂O₅and α-V₂O₅nanowires were prepared with pH controlled precursors.

Self-powered textile for wearable electronics by hybridizing fiber-shaped nanogenerators, solar cells, and supercapacitors

Wearable electronics fabricated on lightweight and flexible substrate are believed to have great potential for portable devices, but their applications are limited by the life span of their batteries. We propose a hybridized self-charging power textile system with the aim of simultaneously collecting outdoor sunshine and random body motion energies and then storing them in an energy storage unit. Both of the harvested energies can be easily converted into electricity by using fiber-shaped dye-sensitized solar cells (for solar energy) and fiber-shaped triboelectric nanogenerators (for random body motion energy) and then further stored as chemical energy in fiber-shaped supercapacitors. Because of the all-fiber-shaped structure of the entire system, our proposed hybridized self-charging textile system can be easily woven into electronic textiles to fabricate smart clothes to sustainably operate mobile or wearable electronics.