Formation of nanostructured, nanocrystalline boron nitride microparticles with diatom-derived 3-D shapes

Small-Scale Biological and Artificial Multidimensional Sensors for 3D Sensing

A vast majority of existing sub-millimeter-scale sensors have a planar, 2D geometry as a result of conventional top-down lithographic procedures. However, 2D sensors often suffer from restricted sensing capability, allowing only partial measurements of 3D quantities. Here, nano/microscale sensors with different geometric (1D, 2D, and 3D) configurations are reviewed to introduce their advantages and limitations when sensing changes in quantities in 3D space. This Review categorizes sensors based on their geometric configuration and sensing capabilities. Among the sensors reviewed here, the 3D configuration sensors defined on polyhedral structures are especially advantageous when sensing spatially distributed 3D quantities. The nano- and microscale vertex configuration forming polyhedral structures enable full 3D spatial sensing due to orthogonally aligned sensing elements. Particularly, the cubic configuration leveraged in 3D sensors offers an array of diverse applications in the field of biosensing for micro-organisms and proteins, optical metamaterials for invisibility cloaking, 3D imaging, and low-power remote sensing of position and angular momentum for use in microbots. Here, various 3D sensors are compared to assess the advantages of their geometry and its impact on sensing mechanisms. 3D biosensors in nature are also explored to provide vital clues for the development of novel 3D sensors.

Synthesis and 3D Interconnected Nanostructured h-BN-Based Biocomposites by Low-Temperature Plasma Sintering: Bone Regeneration Applications

Recent advances and demands in biomedical applications drive a large amount of research to synthesize easily scalable low-density, high-strength, and wear-resistant biomaterials. The chemical inertness with low density combined with high strength makes h-BN one of the promising materials for such application. In this work, three-dimensional hexagonal boron nitride (h-BN) interconnected with boron trioxide (B₂O₃) was prepared by easily scalable and energy efficient spark plasma sintering (SPS) process. The composite structure shows significant densification (1.6-1.9 g/cm³) and high surface area (0.97-14.5 m²/g) at an extremely low SPS temperature of 250 °C. A high compressive strength of 291 MPa with a reasonably good wear resistance was obtained for the composite structure. The formation of strong covalent bonds between h-BN and B₂O₃ was formulated and established by molecular dynamics simulation. The composite showed significant effect on cell viability/proliferation. It shows a high mineralized nodule formation over the control, which suggests its use as a possible osteogenic agent in bone formation.

Tunable multimodal adhesion of 3D, nanocrystalline CoFe2O4 pollen replicas

3D replicas of sunflower pollen microparticles, comprised of a multicomponent magnetic spinel ferrite (CoFe₂O₄) with tailorable adhesive properties, have been synthesized for the first time via a conformal layer-by-layer (LbL) surface sol-gel (SSG) deposition process followed by organic pyrolysis and oxide compound formation at a peak temperature of 600 °C-900 °C. These high-fidelity ferrite pollen replicas exhibited multimodal (van der Waals, vdW, and magnetic) adhesion that could be tuned via control of the CoFe₂O₄ nanoparticle and crystal sizes. The CoFe₂O₄ pollen replicas exhibited a non-monotonic change in short-range (~10 nm) vdW adhesion with an increase in the peak firing temperature, which was consistent with the counteracting effects of particle coarsening on the size and number of nanoparticles present on the sharp tips of the echini (spines) on the pollen replica surfaces. The longer-range (up to ~1 mm) magnetic force of adhesion increased monotonically with an increase in firing temperature, which was consistent with the observed increases in the values of the saturation and remanent magnetization of CoFe₂O₄ with an increase in average nanocrystal size. By adjusting the nanocrystal/nanoparticle sizes of the CoFe₂O₄ pollen replicas, the total force of adhesion (vdW  +  magnetic) to a magnetic substrate could be increased by a factor of ~3 relative to native pollen grains.

Pure &crystallized 2D Boron Nitride sheets synthesized via a novel process coupling both PDCs and SPS methods

Within the context of emergent researches linked to graphene, it is well known that h-BN nanosheets (BNNSs), also referred as 2D BN, are considered as the best candidate for replacing SiO₂ as dielectric support or capping layers for graphene. As a consequence, the development of a novel alternative source for highly crystallized h-BN crystals, suitable for a further exfoliation, is a prime scientific issue. This paper proposes a promising approach to synthesize pure and well-crystallized h-BN flakes, which can be easily exfoliated into BNNSs. This new accessible production process represents a relevant alternative source of supply in response to the increasing need of high quality BNNSs. The synthesis strategy to prepare pure h-BN is based on a unique combination of the Polymer Derived Ceramics (PDCs) route with the Spark Plasma Sintering (SPS) process. Through a multi-scale chemical and structural investigation, it is clearly shown that obtained flakes are large (up to 30 μm), defect-free and well crystallized, which are key-characteristics for a subsequent exfoliation into relevant BNNSs.

Boron nitride ceramics from molecular precursors: synthesis, properties and applications

Hexagonal boron nitride (h-BN) attracts considerable interest particularly when it is prepared from borazine-based single-source precursors through chemical routes suitable for the shaping and the nanostructuration of the final ceramic.

Polymer-Derived Boron Nitride: A Review on the Chemistry, Shaping and Ceramic Conversion of Borazine Derivatives

Boron nitride (BN) is a III-V compound which is the focus of important research since its discovery in the early 19th century. BN is electronic to carbon and thus, in the same way that carbon exists as graphite, BN exists in the hexagonal phase. The latter offers an unusual combination of properties that cannot be found in any other ceramics. However, these properties closely depend on the synthesis processes. This review states the recent developments in the preparation of BN through the chemistry, shaping and ceramic conversion of borazine derivatives. This concept denoted as Polymer-Derived Ceramics (PDCs) route allows tailoring the chemistry of precursors to elaborate complex BN shapes which cannot be obtained by conventional process. The effect of the chemistry of the molecular precursors, i.e., borazine and trichloroborazine, and their polymeric derivatives i.e., polyborazylene and poly[tri(methylamino)borazine], in which the specific functional groups and structural motifs determine the shaping potential by conventional liquid-phase process and plastic-forming techniques is discussed. Nanotubes, nano-fibers, coatings, monoliths and fiber-reinforced matrix composites are especially described. This leads to materials which are of significant engineering interest.

Synthesis of hexagonal boron nitride graphene-like few layers

Self-standing highly crystallized hexagonal boron nitride (h-BN) mono-, bi- and few-layers have been obtained for the first time via the Polymer Derived Ceramics (PDCs) route by adding lithium nitride (Li₃N) micropowders to liquid-state polyborazylene (PBN). Incorporation of Li₃N as a crystallization promoter allows the onset of crystallization of h-BN at a lower temperature (1200 °C) than under classical conditions (1800 °C). The hexagonal structure was confirmed by both electron and X-ray diffraction.

Fabrication of nanopatterned polymeric microparticles using a diatom as a sacrificial template

Diatoms serve as sacrificial templates to fabricate polymeric microparticles with elaborate nano-scale architecture.

Biotemplated materials for sustainable energy and environment: current status and challenges

Materials science will play a key role in the further development of emerging solutions for the increasing problems of energy and environment. Materials found in nature have many inspiring structures, such as hierarchical organizations, periodic architectures, or nanostructures, that endow them with amazing functions, such as energy harvesting and conversion, antireflection, structural coloration, superhydrophobicity, and biological self-assembly. Biotemplating is an effective strategy to obtain morphology-controllable materials with structural specificity, complexity, and related unique functions. Herein, we highlight the synthesis and application of biotemplated materials for six key areas of energy and environment technologies, namely, photocatalytic hydrogen evolution, CO(2) reduction, solar cells, lithium-ion batteries, photocatalytic degradation, and gas/vapor sensing. Although the applications differ from each other, a common fundamental challenge is to realize optimum structures for improved performances. We highlight the role of four typical structures derived from biological systems exploited to optimize properties: hierarchical (porous) structures, periodic (porous) structures, hollow structures, and nanostructures. We also provide examples of using biogenic elements (e.g., C, Si, N, I, P, S) for the creation of active materials. Finally, we disscuss the challenges of achieving the desired performance for large-scale commercial applications and provide some useful prototypes from nature for the biomimetic design of new materials or systems. The emphasis is mainly focused on the structural effects and compositional utilization of biotemplated materials.

3D imaging of diatoms with ion-abrasion scanning electron microscopy

Ion-abrasion scanning electron microscopy (IASEM) takes advantage of focused ion beams to abrade thin sections from the surface of bulk specimens, coupled with SEM to image the surface of each section, enabling 3D reconstructions of subcellular architecture at approximately 30nm resolution. Here, we report the first application of IASEM for imaging a biomineralizing organism, the marine diatom Thalassiosira pseudonana. Diatoms have highly patterned silica-based cell wall structures that are unique models for the study and application of directed nanomaterials synthesis by biological systems. Our study provides new insights into the architecture and assembly principles of both the "hard" (siliceous) and "soft" (organic) components of the cell. From 3D reconstructions of developmentally synchronized diatoms captured at different stages, we show that both micro- and nanoscale siliceous structures can be visualized at specific stages in their formation. We show that not only are structures visualized in a whole-cell context, but demonstrate that fragile, early-stage structures are visible, and that this can be combined with elemental mapping in the exposed slice. We demonstrate that the 3D architectures of silica structures, and the cellular components that mediate their creation and positioning can be visualized simultaneously, providing new opportunities to study and manipulate mineral nanostructures in a genetically tractable system.

An overview of silica in biology: its chemistry and recent technological advances

Biomineralisation is widespread in the biological world and occurs in bacteria, single-celled protists, plants, invertebrates and vertebrates. Minerals formed in the biological environment often show unusual physical properties (e.g. strength, degree of hydration) and often have structures that exhibit order on many length scales. Biosilica, found in single cell organisms through to higher plants and primitive animals (sponges), is formed from an environment that is undersaturated with respect to silicon and under conditions of around neutral pH and low temperature, ca. 4-40 degrees C. Formation of the mineral may occur intra- or extra-cellularly, and specific biochemical locations for mineral deposition that include lipids, proteins and carbohydrates are known. In most cases, the formation of the mineral phase is linked to cellular processes, understanding of which could lead to the design of new materials for biomedical, optical and other applications. This Chapter briefly describes the occurrence of silica in biology including known roles for the mineral phase, the chemistry of the material, the associated biomolecules and some recent applications of this knowledge in materials chemistry.The terminology which is used in this and other contributions within this volume is as follows: Si: the chemical symbol for the element and the generic term used when the nature of the specific silicon compound is not known. Si(OH) ( 4 ): orthosilicic acid, the fundamental building block used in the formation of silicas. SiO ( 2 ) x nH ( 2 ) O or SiO ( 2-x ) (OH) ( 2x ) x 2H ( 2 ) O: amorphous, hydrated, polymerised material. Oligomerisation: the formation of dimers and small oligomers from orthosilicic acid by removal of water. For example, 2Si(OH)(4) <--> (HO)(3)Si-O-Si(OH)(3) + H(2)O Polymerisation: the mutual condensation of silicic acid to give molecularly coherent units of increasing size. Organosilicon compound: must contain silicon covalently bonded to carbon within a distinct chemical species Silane: a compound having silicon atom(s) and organic chemical groups often connected through an oxygen linkage; e.g. tetrethoxy or tetramethoxysilane Silanol: hydroxyl group bonded to silicon atom Silicate: a chemically specific ion having negative charge (e.g. [Formula: see text]), term also used to describe salts (e.g. sodium silicate Na(2)SiO(3)) Opal: the term used to describe the gem-stone and often used to describe the type of amorphous silica produced by biological organisms. The two are similar in structure at the molecular level (disordered or amorphous), but at higher levels of structural organisation are distinct from one another.