A Bimetallic Organic Framework with Mn in MIL-101(Cr) for Lithium-Sulfur Batteries

Lithium-sulfur batteries (LSBs) show excellent performance in terms of specific capacity and energy density. However, the cyclic stability of LSBs is compromised due to the "shuttle effect", which hinders the practical applications of LSBs. Herein, a metal-organic framework (MOF) based on Cr ions as the main body composition, commonly known as MIL-101(Cr), was utilized to minimize the shuttle effect and improve the cyclic performance of LSBs. To obtain MOFs with a certain adsorption capacity for lithium polysulfide and a certain catalytic capacity, we propose an effective strategy of incorporating sulfur-loving metal ions (Mn) into the skeleton to enhance the reaction kinetics at the electrode. Based on the oxidation doping method, Mn²⁺ was uniformly dispersed in MIL-101(Cr) to produce bimetallic Cr₂O₃/MnO_x as a novel sulfur-carrying cathode material. Then, a sulfur injection process was carried out by melt diffusion to obtain the sulfur-containing Cr₂O₃/MnO_x-S electrode. Moreover, an LSB assembled with Cr₂O₃/MnO_x-S showed improved first-cycle discharge (1285 mAh·g^-1 at 0.1 C) and cyclic performance (721 mAh·g^-1 at 0.1 C after 100 cycles), and the overall performance was much better than that of monometallic MIL-101(Cr) as a sulfur carrier. These results revealed that the physical immobilization method of MIL-101(Cr) positively affected the adsorption of polysulfides, while the bimetallic composite Cr₂O₃/MnO_x formed by the doping of sulfur-loving Mn²⁺ into the porous MOF produced a good catalytic effect during LSB charging. This research provides a novel approach for preparing efficient sulfur-containing materials for LSBs.

Role of supercritical carbon dioxide (scCO2) in fabrication of inorganic-based materials: a green and unique route

In recent times, the supercritical carbon dioxide (scCO₂) process has attracted increasing attention in fabricating diverse materials due to the attractive features of environmentally benign nature and economically promising character. Owing to these unique characteristics and high-penetrability, as well as diffusivity conditions of scCO₂, this high-pressure technology, with mild operation conditions, cost-effective, and non-toxic, among others, is often applied to fabricate various organic and inorganic-based materials, resulting in the unique crystal architectures (amorphous, crystalline, and heterojunction), tunable architectures (nanoparticles, nanosheets, and aerogels) for diverse applications. In this review, we give an emphasis on the fabrication of various inorganic-based materials, highlighting the recent research on the driving factors for improving the quality of fabrication in scCO₂, procedures for production and dispersion in scCO₂, as well as common indicators utilized to assess quality and processing ability of materials. Next, we highlight the effects of specific properties of scCO₂ towards synthesizing the highly functional inorganic-based nanomaterials. Finally, we summarize this compilation with interesting perspectives, aiming to arouse a more comprehensive utilization of scCO₂ to broaden the horizon in exploring the green/eco-friendly processing of such versatile inorganic-based materials. Together, we firmly believe that this compilation endeavors to disclose the latent capability and universal prevalence of scCO₂ in the synthesis and processing of inorganic-based materials.

Temperature-Limited Synthesis of Copper Manganites along the Borderline of the Amorphous/Crystalline State and Their Catalytic Activity in CO Oxidation

Copper manganese oxides (CMO) with CuMn2O4 composition are well-known catalysts, which are widely used for the oxidative removal of dangerous chemicals, e.g., enhancing the CO to CO2 conversion. Their catalytic activity is the highest, close to those of the pre-crystalline and amorphous states. Here we show an easy way to prepare a stable CMO material at the borderline of the amorphous and crystalline state (BAC-CMO) at low temperatures (<100 °C) followed annealing at 300 °C and point out its excellent catalytic activity in CO oxidation reactions. We demonstrate that the temperature-controlled decomposition of [Cu(NH3)4](MnO4)2 in CHCl3 and CCl4 at 61 and 77 °C, respectively, gives rise to the formation of amorphous CMO and NH4NO3, which greatly influences the composition as well as the Cu valence state of the annealed CMOs. Washing with water and annealing at 300 °C result in a BAC-CMO material, whereas the direct annealing of the as-prepared product at 300 °C gives rise to crystalline CuMn2O4 (sCMO, 15-40 nm) and ((Cu,Mn)2O3, bCMO, 35-40 nm) mixture. The annealing temperature influences both the quantity and crystallite size of sCMO and bCMO products. In 0.5% CO/0.5% O2/He mixture the best CO to CO2 conversion rates were achieved at 200 °C with the BAC-CMO sample (0.011 mol CO2/(m2 h)) prepared in CCl4. The activity of this BAC-CMO at 125 °C decreases to half of its original value within 3 h and this activity is almost unchanged during another 20 h. The BAC-CMO catalyst can be regenerated without any loss in its catalytic activity, which provides the possibility for its long-term industrial application.

A novel high-performance CeO2-CuMn2O4 catalyst for toluene degradation

A series of spinel CuM₂O₄ (M = Mn, Fe, and Al) was used as the catalyst to investigate the effective degradation of toluene, and then CuMn₂O₄ with better catalytic activity was selected as the research object to study its activity at different ratios of Cu and Mn. Meanwhile, CeO₂ was introduced to modify CuMn bimetallic oxide to improve its catalytic performance. The structure, morphology, and valence states of surface elements of as-prepared catalysts were characterized by XRD, TEM, SEM, N₂ adsorption-desorption, XPS, and H₂-TPR. Using toluene as a probe molecule, the catalytic activity of the catalyst was tested and the results showed that the conversion rate of toluene catalyzed by CeO₂-CuMn₂O₄ catalyst can reach 90% at 200 °C (T₉₀) and 100% at 240 °C (T₁₀₀). The CO₂ yield can also reach 100% at 248 °C. Moreover, the possible catalytic mechanism for toluene by the CeO₂-CuMn₂O₄ was briefly explored. The catalytic oxidation of toluene over the oxide follows the Mars-van Krevelen mechanism.

Porous Mn-based oxides for complete ethanol and toluene catalytic oxidation: the relationship between structure and performance

SmMn₂O₅ exhibited a higher catalytic activity for catalytic oxidation of ethanol and toluene than SmMnO₃, Mn₃O₄ and Mn₂O₃. Mn³⁺–Mn³⁺ dimers facilitate C–C bond cleavage.

Low-temperature catalytic oxidation of benzene over nanocrystalline Cu–Mn composite oxides by facile sol–gel synthesis

We prepare a series of nanocrystalline copper–manganese oxides by a facile citric acid sol–gel method, and test their activities for catalytic oxidation of benzene.

Supercritical Antisolvent Precipitation of Amorphous Copper-Zinc Georgeite and Acetate Precursors for the Preparation of Ambient-Pressure Water-Gas-Shift Copper/Zinc Oxide Catalysts

A series of copper–zinc acetate and zincian georgeite precursors have been produced by supercritical CO₂ antisolvent (SAS) precipitation as precursors to Cu/ZnO catalysts for the water gas shift (WGS) reaction. The amorphous materials were prepared by varying the water/ethanol volumetric ratio in the initial metal acetate solutions. Water addition promoted georgeite formation at the expense of mixed metal acetates, which are formed in the absence of the water co‐solvent. Optimum SAS precipitation occurs without water to give high surface areas, whereas high water content gives inferior surface areas and copper–zinc segregation. Calcination of the acetates is exothermic, producing a mixture of metal oxides with high crystallinity. However, thermal decomposition of zincian georgeite resulted in highly dispersed CuO and ZnO crystallites with poor structural order. The georgeite‐derived catalysts give superior WGS performance to the acetate‐derived catalysts, which is attributed to enhanced copper–zinc interactions that originate from the precursor.

The effect of sodium species on methanol synthesis and water–gas shift Cu/ZnO catalysts: utilising high purity zincian georgeite

The effect of sodium species on the physical and catalytic properties of Cu/ZnO catalysts derived from zincian georgeite has been investigated. Catalysts prepared with <100 ppm to 2.1 wt% Na⁺, using a supercritical CO₂ antisolvent technique, were characterised and tested for the low temperature water–gas shift reaction and also CO₂ hydrogenation to methanol. It was found that zincian georgeite catalyst precursor stability was dependent on the Na⁺ concentration, with the 2.1 wt% Na⁺-containing sample uncontrollably ageing to malachite and sodium zinc carbonate. Samples with lower Na⁺ contents (<100–2500 ppm) remained as the amorphous zincian georgeite phase, which on calcination and reduction resulted in similar CuO/Cu particle sizes and Cu surface areas. The aged 2.1 wt% Na⁺ containing sample, after calcination and reduction, was found to comprise of larger CuO crystallites and a lower Cu surface area. However, calcination of the high Na⁺ sample immediately after precipitation (before ageing) resulted in a comparable CuO/Cu particle size to the lower (<100–2500 ppm) Na⁺ containing samples, but with a lower Cu surface area, which indicates that Na⁺ species block Cu sites. Activity of the catalysts for the water–gas shift reaction and methanol yields in the methanol synthesis reaction correlated with Na⁺ content, suggesting that Na⁺ directly poisons the catalyst. In situ XRD analysis showed that the ZnO crystallite size and consequently Cu crystallite size increased dramatically in the presence of water in a syn-gas reaction mixture, showing that stabilisation of nanocrystalline ZnO is required. Sodium species have a moderate effect on ZnO and Cu crystallite growth rate, with lower Na⁺ content resulting in slightly reduced rates of growth under reaction conditions.

Cobalt Ferrite Bearing Nitrogen-Doped Reduced Graphene Oxide Layers Spatially Separated with Microporous Carbon as Efficient Oxygen Reduction Electrocatalyst

The present work discloses how high-quality dispersion of fine particles of cobalt ferrite (CF) could be attained on nitrogen-doped reduced graphene oxide (CF/N-rGO) and how this material in association with a microporous carbon phase could deliver significantly enhanced activity toward electrochemical oxygen reduction reaction (ORR). Our study indicates that the microporous carbon phase plays a critical role in spatially separating the layers of CF/N-rGO and in creating a favorable atmosphere to ensure the seamless distribution of the reactants to the active sites located on CF/N-rGO. In terms of the ORR current density, the heat-treated hybrid catalyst at 150 °C (CF/N-rGO-150) is found to be clearly outperforming (7.4 ± 0.5 mA/cm(2)) the state-of-the-art 20 wt % Pt-supported carbon catalyst (PtC) (5.4 ± 0.5 mA/cm(2)). The mass activity and stability of CF-N-rGO-150 are distinctly superior to PtC even after 5000 electrochemical cycles. As a realistic system level exploration of the catalyst, testing of a primary zinc-air battery could be demonstrated using CF/N-rGO-150 as the cathode catalyst. The battery is giving a galvanostatic discharge time of 15 h at a discharge current density of 20 mA/cm(2) and a specific capacity of ∼630 mAh g(-1) in 6 M KOH by using a Zn foil as the anode. Distinctly, the battery performance of this system is found to be superior to that of PtC in less concentrated KOH solution as the electrolyte.

Novel cobalt zinc oxide Fischer–Tropsch catalysts synthesised using supercritical anti-solvent precipitation

Cobalt zinc oxide catalysts have been prepared by anti-solvent precipitation in supercritical CO₂ and investigated for CO hydrogenation.