Double-Heterojunction-Based HgTe Colloidal Quantum Dot Imagers

Photodetectors based on HgTe colloidal quantum dots (CQDs) are expected to enable the next generation of infrared detection technology due to their low-cost preparation, widely tunable absorption, and direct integration with Si-based electronics. However, the fabrication of HgTe CQD photodiode focal plane arrays (FPAs) has been hampered by the creation of rectifying homojunctions through delicate doping modulation and the time-consuming layer-by-layer assembly of the QD photoactive layer. Herein we address these challenges by exploring energetically favored ZnO/HgTe/ZnTe double heterojunctions (DH), and by forming colloidally stable HgTe ink that enables one-step direct film deposition. The DH HgTe CQD photodiode operates over a broad spectral range from 400 to 1800 nm, comparable to that of uncooled InGaAs detectors, with a record peak EQE of 56% at 1600 nm. A short-wave infrared (SWIR) imager has been finally demonstrated through monolithic integration with a CMOS readout integrated circuit (ROIC) comprising 640 × 512 pixels. The DH architecture is beneficial for the construction of high-performance HgTe CQD photodiodes compatible with silicon chip integration.

Hydrophobized Metal-Organic Frameworks as Versatile Building Blocks for Tailored Nanocrystal Superlattices

This study introduces an effective strategy for hydrophobizing metal-organic frameworks (MOFs) using oleyl phosphate (OP) ligands. This modification makes MOF particles dispersible in nonpolar solvents and provides them with colloidal stability akin to traditional colloidal nanocrystals (NCs). The resulting OP-capped MOF particles can then be employed as building blocks for constructing various two-dimensional (2D) and 3D superlattices through self-assembly methods typically used for NCs. Additionally, binary superlattices with tailored structures can be achieved by coassembling OP-capped MOF particles with different NCs. This robust surface hydrophobization approach is adaptable to various MOFs, facilitating the rational design and creation of complex MOF-based superstructures.

Enhanced Asymmetric Circularly Polarized Luminescence in Self-Organized Helical Superstructures Enabled by Macro-Chiral Liquid Crystal Quantum Dots

Circularly polarized luminescent (CPL) materials have garnered considerable interest for a variety of advanced optical applications including 3D imaging, data encryption, and asymmetric catalysis. However, the development of high-performance CPL has been hindered by the absence of simple synthetic methods for chiral luminescent emitters that exhibit both high quantum yields and dissymmetry factors. In this study, we present an innovative approach for the synthesis of macro-chiral liquid crystal quantum dots (Ch-QDs/LC) and their CPL performance enhancement through doping with 4-cyano-4'-pentylbiphenyl (5CB), thus yielding a CPL-emitting generator (CEG). The Ch-QDs/LCs were synthesized, and their surfaces functionalized with a chiral mesogenic ligand, specifically cholesteryl benzoate, anchored via a lipoic acid linker. Under the regulation of chiral 2S-Zn2+ coordination complexes, the chiral LC encapsulation process promotes coordinated ligand substitution, resulting in an exceptional quantum yield of 56.3%. This is accompanied by high absorption dissymmetry factor (gabs) and luminescence dissymmetry factor (glum) values ranging from 10-3 to 10-2, surpassing most reported dissymmetry factors by at least an order of magnitude. The modular Ch-QDs/LCs demonstrate the ability to transfer chirality to the surrounding medium efficiently and manifest macro-chiral characteristics within a nematic LC matrix. Utilizing Ch-QDs/LC as an effective CPL emitter within achiral 5CB matrices enabled the system to achieve a maximum glum value of 0.35. The resultant CEG device acted as a direct CPL source, initiating enantioselective photopolymerization.

Stabilization and Surface Functionalization of Palladium Disulfide Nanoparticles with Acetylene Derivatives

Metal chalcogenide nanoparticles have been attracting extensive attention in diverse fields. Traditionally these nanoparticles are stabilized by organic ligands such as thiols and amines involving nonconjugated core-ligand interfacial interactions. In the present study, a facile wet-chemistry method is described for the synthesis of palladium disulfide (PdS2) nanoparticles capped with acetylene derivatives. Spectroscopic and electrochemical measurements suggest that conjugated Pd-C≡ linkages are formed at the core-ligand interface and facilitate electronic coupling and hence manipulation of the nanoparticle optical and electronic properties. The unique interfacial linkages also allow further functionalization of the nanoparticles by metathesis reaction with olefin derivatives, as manifested in the reaction with vinylferrocene. This research opens new avenues for the structural engineering and functionalization of metal chalcogenide nanoparticles.

Unraveling the Formation of Ternary AgCuSe Crystalline Nanophases and Their Potential as Antibacterial Agents

AgCuSe nanoparticles could contribute to the growth of strongly light-absorbing thin films and solids with fast ion mobility, among other potential properties. Nevertheless, few methods have been developed so far for the synthesis of AgCuSe nanoparticles, and those reported deliver nanostructures with relatively large sizes and broad size and shape distributions. In this work, a colloidal cation exchange method is established for the easy synthesis of AgCuSe NPs with ca. 8 nm diameters and narrow size dispersion. Notably, in this lower size range the conucleation and growth of two stoichiometric ternary compounds are generally observed, namely the well-known eucairite AgCuSe compound and the novel fischesserite-like Ag3CuSe2 phase, the latter being less thermodynamically stable as predicted computationally and assessed experimentally. An optimal range of Cu/Ag precursor molar ratio has been identified to ensure the growth of ternary nanoparticles and, more specifically, that of the metastable Ag3CuSe2 nanophase isolated for the first occasion. The attained size range for the material paves the way for utilizing AgCuSe nanoparticles in new ways within the field of biomedicine: the results obtained here confirm the antibacterial activity of the new Ag x Cu y Se z nanoparticles against Gram-positive bacteria, with significantly low values of the minimal inhibitory concentration.

Polytypic metal chalcogenide nanocrystals

By engineering chemically identical but structurally distinct materials into intricate and sophisticated polytypic nanostructures, which often surpass their pure phase objects and even produce novel physical and chemical properties, exciting applications in the fields of photovoltaics, electronics and photocatalysis can be achieved. In recent decades, various methods have been developed for synthesizing a library of polytypic nanocrystals encompassing IV, III-V and II-VI polytypic semiconductors. The exceptional performances of polytypic metal chalcogenide nanocrystals have been observed, making them highly promising candidates for applications in photonics and electronics. However, achieving high-precision control over the morphology, composition, crystal structure, size, homojunctions, and periodicity of polytypic metal chalcogenide nanostructures remains a significant synthetic challenge. This review article offers a comprehensive overview of recent progress in the synthesis and control of polytypic metal chalcogenide nanocrystals using colloidal synthetic strategies. Starting from a concise introduction on the crystal structures of metal chalcogenides, the subsequent discussion delves into the colloidal synthesis of polytypic metal chalcogenide nanocrystals, followed by an in-depth exploration of the key factors governing polytypic structure construction. Subsequently, we provide comprehensive insights into the physical properties of polytypic metal chalcogenide nanocrystals, which exhibit strong correlations with their applications. Thereafter, we emphasize the significance of polytypic nanostructures in various applications, such as photovoltaics, photocatalysis, transistors, thermoelectrics, stress sensors, and the electrocatalytic hydrogen evolution. Finally, we present a summary of the recent advancements in this research field and provide insightful perspectives on the forthcoming challenges, opportunities, and future research directions.

Plasmon-Induced Hot Electrons in Nanostructured Materials: Generation, Collection, and Application to Photochemistry

Plasmon refers to the coherent oscillation of all conduction-band electrons in a nanostructure made of a metal or a heavily doped semiconductor. Upon excitation, the plasmon can decay through different channels, including nonradiative Landau damping for the generation of plasmon-induced energetic carriers, the so-called hot electrons and holes. The energetic carriers can be collected by transferring to a functional material situated next to the plasmonic component in a hybrid configuration to facilitate a range of photochemical processes for energy or chemical conversion. This article centers on the recent advancement in generating and utilizing plasmon-induced hot electrons in a rich variety of hybrid nanostructures. After a brief introduction to the fundamentals of hot-electron generation and decay in plasmonic nanocrystals, we extensively discuss how to collect the hot electrons with various types of functional materials. With a focus on plasmonic nanocrystals made of metals, we also briefly examine those based upon heavily doped semiconductors. Finally, we illustrate how site-selected growth can be leveraged for the rational fabrication of different types of hybrid nanostructures, with an emphasis on the parameters that can be experimentally controlled to tailor the properties for various applications.

Phase-Controlled Synthesis and Phase-Change Properties of Colloidal Cu-Ge-Te Nanoparticles

Phase-change memory (PCM) technology has recently attracted a vivid interest for neuromorphic applications, in-memory computing, and photonic integration due to the tunable refractive index and electrical conductivity between the amorphous and crystalline material states. Despite this, it is increasingly challenging to scale down the device dimensions of conventionally sputtered PCM memory arrays, restricting the implementation of PCM technology in mass applications such as consumer electronics. Here, we report the synthesis and structural study of sub-10 nm Cu-Ge-Te (CGT) nanoparticles as suitable candidates for low-cost and ultrasmall PCM devices. We show that our synthesis approach can accurately control the structure of the CGT colloids, such as composition-tuned CGT amorphous nanoparticles as well as crystalline CGT nanoparticles with trigonal α-GeTe and tetragonal Cu2GeTe3 phases. In situ characterization techniques such as high-temperature X-ray diffraction and X-ray absorption spectroscopy reveal that Cu doping in GeTe improves the thermal properties and amorphous phase stability of the nanoparticles, in addition to nanoscale effects, which enhance the nonvolatility characteristics of CGT nanoparticles even further. Moreover, we demonstrate the thin-film fabrication of CGT nanoparticles and characterize their optical properties with spectroscopic ellipsometry measurements. We reveal that CGT nanoparticle thin films exhibit a negative reflectivity change and have good reflectivity contrast in the near-IR spectrum. Our work promotes the possibility to use PCM in nanoparticle form for applications such as electro-optical switching devices, metalenses, reflectivity displays, and phase-change IR devices.

Alkyne-Functionalized Platinum Chalcogenide (S, Se) Nanoparticles

Metal chalcogenide nanoparticles play a vital role in a wide range of applications and are typically stabilized by organic derivatives containing thiol, amine, or carboxyl moieties, where the nonconjugated particle-ligand interfaces limit the electronic interactions between the inorganic cores and organic ligands. Herein, a wet-chemistry method is developed for the facile preparation of stable platinum chalcogenide (S, Se) nanoparticles capped with acetylene derivatives (e.g., 4-ethylphenylacetylene, EPA). The formation of Pt-C≡ conjugated bonds at the nanoparticle interfaces, which is confirmed by optical and X-ray spectroscopic measurements, leads to markedly enhanced electronic interactions between the d electrons of the nanoparticle cores and π electrons of the acetylene moiety, in stark contrast to the mercapto-capped counterparts with only nonconjugated Pt-S- interfacial bonds, as manifested in spectroscopic measurements and density functional theory calculations. This study underscores the significance of conjugated anchoring linkages in the stabilization and functionalization of metal chalcogenides, a unique strategy for diverse applications.

InAs Nanorod Colloidal Quantum Dots with Tunable Bandgaps Deep into the Short-Wave Infrared

InAs colloidal quantum dots (CQDs) have emerged as candidate lead- and mercury-free solution-processed semiconductors for infrared technology due to their appropriate bulk bandgap, which can be tuned by quantum confinement, and promising charge-carrier transport properties. However, the lack of suitable arsenic precursors and readily accessible synthesis conditions have limited InAs CQDs to smaller sizes (<7 nm), with bandgaps largely restricted to <1400 nm in the near-infrared spectral window. Conventional InAs CQD synthesis requires highly reactive, hazardous arsenic precursors, which are commercially scarce, making the synthesis hard to control and study. Here, we present a controlled synthesis strategy (using only readily available and less reactive precursors) to overcome the practical wavelength limitation of InAs CQDs, achieving monodisperse InAs nanorod CQDs with bandgaps tunable from ∼1200 to ∼1800 nm, thus crossing deep into the short-wave infrared (SWIR) region. By controlling the reactivity through in situ precursor complexation, we isolate the reaction mechanism, producing InAs nanorod CQDs that display narrow excitonic features and efficient carrier multiplication. Our work enables InAs CQDs for a wider range of SWIR applications.

Synthesis and functionalization of the six-vertex anionic amido-substituted silicon cluster [Si6{N(SiMe3)Ph}5]. Dalton Trans 2023;52:14949-14955. [PMID: 37800884 DOI: 10.1039/d2dt03952d] [Citation(s) in RCA: 0] [Impact Index Per Article: 0]

The reaction of the six-vertex amido-substituted silicon cluster Si6{N(SiMe3)Ph}6 1 with two equiv. of KC8 results in the abstraction of K{N(SiMe3)Ph} and leads to the contact ion pair 2 including an anionic silicon cluster with two unsubstituted pyramidal vertices. Facile functionalization of 2 was achieved with MeI, SiCl4 and SiBr4 and results in neutral two-fold functionalized silicon clusters.

Optical properties of NIR photoluminescent PbS nanocrystal-based three-dimensional networks

The assembly of nanocrystals (NCs) into three-dimensional network structures is a recently established strategy to produce macroscopic materials with nanoscopic properties. These networks can be formed by the controlled destabilization of NC colloids and subsequent supercritical drying to obtain NC-based aerogels. Even though this strategy has been used for many different semiconductor NCs, the emission of NC-based aerogels is limited to the ultraviolet and visible and no near-infrared (NIR) emitting NC-based aerogels have been investigated in literature until now. In the present work we have optimized a gelation route of NIR emitting PbS and PbS/CdS quantum dots (QDs) by means of a recently established gel formation method using trivalent ions to induce the network formation. Thereby, depending on the surface ligands and QDs used the resulting network structure is different. We propose, that the ligand affinity to the nanocrystal surface plays an essential role during network formation, which is supported by theoretical calculations. The optical properties were investigated with a focus on their steady-state and time resolved photoluminescence (PL). Unlike in PbS/CdS aerogels, the absorption of PbS aerogels and their PL shift strongly. For all aerogels the PL lifetimes are reduced in comparison to those of the building blocks with this reduction being especially pronounced in the PbS aerogels.

Marcus Theory and Tunneling Method for the Electron Transfer Rate Analysis in Quantum Dot Sensitized Solar Cells in the Presence of Blocking Layer

In this research study, the effects of different parameters on the electron transfer rate from three quantum dots (QDs), CdSe, CdS, and CdTe, on three metal oxides (MOs), TiO2, SnO2, and SnO2, in quantum-dot-sensitized solar cells (QDSSCs) with porous structures in the presence of four types of blocking layers, ZnS, ZnO, TiO2, and Al2O3, are modeled and simulated using the Marcus theory and tunneling between two spheres for the first time. Here, the studied parameters include the change in the type and thickness of the blocking layer, the diameter of the QD, and the temperature effect. To model the effect of the blocking layer on the QD, the effective sphere method is used, and by applying it into the Marcus theory equation and the tunneling method, the electron transfer rate is calculated and analyzed. The obtained results in a wide range of temperatures of 250-400 °K demonstrate that, based on the composition of the MO-QD, the increase in the temperature could reduce or increase the electron transfer rate, and the change in the QD diameter could exacerbate the effects of the temperature. In addition, the results show which type and thickness of the blocking layer can achieve the highest electron transfer rate. In order to test the accuracy of the simulation method, we calculate the electron transfer rate in the presence of a blocking layer for a reported sample of a QDSSC manufacturing work, which was obtained with an error of ~3%. The results can be used to better interpret the experimental observations and to assist with the design and selection of the appropriate combination of MO-QD in the presence of a blocking layer effect.

A Broadband Photodetector Based on PbS Quantum Dots and Graphene with High Responsivity and Detectivity

A high-efficiency photodetector consisting of colloidal PbS quantum dots (QDs) and single-layer graphene was prepared in this research. In the early stage, PbS QDs were synthesized and characterized, and the results showed that the product conformed with the characteristics of high-quality PbS QDs. Afterwards, the photodetector was derived through steps, including the photolithography and etching of indium tin oxide (ITO) electrodes and the graphene active region, as well as the spin coating and ligand substitution of the PbS QDs. After application testing, the photodetector, which was prepared in this research, exhibited outstanding properties. Under visible and near-infrared light, the highest responsivities were up to 202 A/W and 183 mA/W, respectively, and the highest detectivities were up to 2.24 × 10¹¹ Jones and 2.47 × 10⁸ Jones, respectively, with light densities of 0.56 mW/cm² and 1.22 W/cm², respectively. In addition to these results, the response of the device and the rise and fall times for the on/off illumination cycles showed its superior performance, and the fastest response times were approximately 0.03 s and 1.0 s for the rise and fall times, respectively. All the results illustrated that the photodetector based on PbS and graphene, which was prepared in this research, possesses the potential to be applied in reality.

Mercury chalcogenide colloidal quantum dots for infrared photodetection: from synthesis to device applications

Commercial infrared (IR) photodetectors based on epitaxial growth inorganic semiconductors, e.g. InGaAs and HgCdTe, suffer from high fabrication cost, poor compatibility with silicon integrated circuits, rigid substrates and bulky cooling systems, which leaves a large development window for the emerging solution-processable semiconductor-based photo-sensing devices. Among the solution-processable semiconductors, mercury (Hg) chalcogenide colloidal quantum dots (QDs) exhibit unique ultra-broad and tuneable photo-responses in the short-wave infrared to far-wave infrared range, and have demonstrated photo-sensing abilities comparable to the commercial products, especially with advances in high operation temperature. Here, we provide a focused review on photodetectors employing Hg chalcogenide colloidal QDs, with a comprehensive summary of the essential progress in the areas of synthesis methods of QDs, property control, device engineering, focus plane array integration, etc. Besides imaging demonstrations, a series of Hg chalcogenide QD photodetector based flexible, integrated, multi-functional applications are also summarized. This review shows prospects for the next-generation low-cost highly-sensitive and compact IR photodetectors based on solution-processable Hg chalcogenide colloidal QDs.

A Review of Transition Metal Sulfides as Counter Electrodes for Dye-Sensitized and Quantum Dot-Sensitized Solar Cells

Third-generation solar cells, including dye-sensitized solar cells (DSSCs) and quantum dot-sensitized solar cells (QDSSCs), have been associated with low-cost material requirements, simple fabrication processes, and mechanical robustness. Hence, counter electrodes (CEs) are a critical component for the functionality of these solar cells. Although platinum (Pt)-based CEs have been dominant in CE fabrication, they are costly and have limited market availability. Therefore, it is important to find alternative materials to overcome these issues. Transition metal chalcogenides (TMCs) and transition metal dichalcogenides (TMDs) have demonstrated capabilities as a more cost-effective alternative to Pt materials. This advantage has been attributed to their strong electrocatalytic activity, excellent thermal stability, tunability of bandgap energies, and variable crystalline morphologies. In this study, a comprehensive review of the major components and working principles of the DSSC and QDSSC are presented. In developing CEs for DSSCs and QDSSCs, various TMS materials synthesized through several techniques are thoroughly reviewed. The performance efficiencies of DSSCs and QDSSCs resulting from TMS-based CEs are subjected to in-depth comparative analysis with Pt-based CEs. Thus, the power conversion efficiency (PCE), fill factor (FF), short circuit current density (Jsc) and open circuit voltage (Voc) are investigated. Based on this review, the PCEs for DSSCs and QDSSCs are found to range from 5.37 to 9.80% (I-/I3- redox couple electrolyte) and 1.62 to 6.70% (S-2/Sx- electrolyte). This review seeks to navigate the future direction of TMS-based CEs towards the performance efficiency improvement of DSSCs and QDSSCs in the most cost-effective and environmentally friendly manner.

Near-infrared-IIb emitting single-atom catalyst for imaging-guided therapy of blood-brain barrier breakdown after traumatic brain injury

The blood-brain barrier breakdown, as a prominent feature after traumatic brain injury, always triggers a cascade of biochemical events like inflammatory response and free radical-mediated oxidative damage, leading to neurological dysfunction. The dynamic monitoring the status of blood-brain barrier will provide potent guidance for adopting appropriate clinical intervention. Here, we engineer a near-infrared-IIb Ag₂Te quantum dot-based Mn single-atom catalyst for imaging-guided therapy of blood-brain barrier breakdown of mice after traumatic brain injury. The dynamic change of blood-brain barrier, including the transient cerebral hypoperfusion and cerebrovascular damage, could be resolved with high spatiotemporal resolution (150 ms and ~ 9.6 µm). Notably, the isolated single Mn atoms on the surface of Ag₂Te exhibited excellent catalytic activity for scavenging reactive oxygen species to alleviate neuroinflammation in brains. The timely injection of Mn single-atom catalyst guided by imaging significantly promoted the reconstruction of blood-brain barrier and recovery of neurological function after traumatic brain injury.

Noninvasive Gastrointestinal Tract Imaging Using BSA-Ag2Te Quantum Dots as a CT/NIR-II Fluorescence Dual-Modal Imaging Probe in Vivo

The combination of high-resolution computed tomography (CT) and the real-time sensitive second near-infrared window (NIR-II) fluorescence bioimaging can provide complementary information for the diagnosis, progression and prognosis of gastrointestinal disorders. Ag₂Te quantum dots (QDs) are a kind of promising CT/NIR-II fluorescence dual-modal imaging probe due to their high atomic number and narrow bandgap. However, conventional Ag₂Te QDs synthesized by oil phase approaches often suffer from complicated steps, harsh reaction conditions, and toxic organic solvents. Herein, we report the synthesis of bovine serum albumin (BSA)-Ag₂Te QDs using a biomineralization approach for CT/NIR-II fluorescence dual-modal imaging of the gastrointestinal tract. The BSA-Ag₂Te QDs are fabricated in a facile one-pot approach under mild conditions and exhibit homogeneous size, favorable monodispersity, admirable aqueous solubility, excellent X-ray attenuation properties, and outstanding NIR-II fluorescence performance. In vivo imaging experiments show that BSA-Ag₂Te QDs can be used in gastrointestinal tract CT/NIR-II dual-modal imaging with high spatiotemporal resolution and sensitivity. In addition, in an intestinal obstruction mouse model, accurate lesion positioning and imaging-guided obstruction relief surgery are successfully realized based on BSA-Ag₂Te QDs. Besides, BSA-Ag₂Te QDs have outstanding biocompatibility in vitro and in vivo. This study presents a high-performance and biosafe CT/NIR-II fluorescence dual-modal imaging probe for visualizing the gastrointestinal tract in vivo.

Thermoelectric Silver-Based Chalcogenides

Heat is abundantly available from various sources including solar irradiation, geothermal energy, industrial processes, automobile exhausts, and from the human body and other living beings. However, these heat sources are often overlooked despite their abundance, and their potential applications remain underdeveloped. In recent years, important progress has been made in the development of high-performance thermoelectric materials, which have been extensively studied at medium and high temperatures, but less so at near room temperature. Silver-based chalcogenides have gained much attention as near room temperature thermoelectric materials, and they are anticipated to catalyze tremendous growth in energy harvesting for advancing internet of things appliances, self-powered wearable medical systems, and self-powered wearable intelligent devices. This review encompasses the recent advancements of thermoelectric silver-based chalcogenides including binary and multinary compounds, as well as their hybrids and composites. Emphasis is placed on strategic approaches which improve the value of the figure of merit for better thermoelectric performance at near room temperature via engineering material size, shape, composition, bandgap, etc. This review also describes the potential of thermoelectric materials for applications including self-powering wearable devices created by different approaches. Lastly, the underlying challenges and perspectives on the future development of thermoelectric materials are discussed.

Ultra-mild synthesis of nanometric metal chalcogenides using organyl chalcogenide precursors

Bis(trialkylsilyl) monochalcogenides and diorganyl dichalcogenides, (R₃Si)₂E and R₂E₂ (E = S, Se or Te and R = alkyl, aryl or allyl group), have emerged in the past decade as excellent reagents for the synthesis of metal chalcogenide nanoparticles (NPs) and clusters owing to their ability to transfer the chalcogenide anion (E^2-) under ultra-mild conditions and versatility in reacting even with non-conventional metal reagents or being employed in a variety of synthetic methods. In comparison, the related non-silylated diorganyl monochalcogenides R₂E have received attention only recently for the solution phase synthesis of metal chalcogenide NPs. In spite of sharing many similarities, these three families of organyl chalcogenides are different in their coordination ability and decomposition behavior, and therefore in reactivities towards metal reagents. This feature article provides a concise overview on the use of these three families as synthons for the ultralow-temperature synthesis of metal chalcogenide nanomaterials, deliberating their different decomposition mechanisms and critically assessing their advantages for certain applications. More specifically, it discusses their usefulness in (i) affording molecular precursors with different kinetic and thermal stabilities, (ii) isolating reactive intermediates for comprehending the mechanism of molecule-to-nanoparticle transformation and, therefore, achieving fine control over the synthesis, (iii) stabilizing isolable metastable or difficult-to-achieve phases, and (iv) yielding complex ternary nanoparticles with controlled stoichiometry or composites with sensitive materials without modifying the characteristics of the latter. Besides providing a perspective on the low-temperature synthesis of nanomaterials, this overview is expected to assist further progress, particularly in the field of R₂E, leading to interesting materials including metastable ones for new applications.

Mid-Infrared HgTe Colloidal Quantum Dots In-Situ Passivated by Iodide

Today, colloidal quantum dots (CQDs) have received wide attention due to their properties of tunable infrared absorption. For example, HgTe colloidal quantum dots have shown excellent optical absorption (absorption coefficient α > 104 cm−1), spectral absorption tunability covering the entire infrared atmospheric window, and even the terahertz (THz). However, the efficient surface passivation of HgTe CQDs was limited by the highly sterically hindered long-chain organic ligands. Here, we demonstrate a new method to synthesize monodisperse mid-infrared HgTe CQDs, and the preparation process of the Hg precursor solution is optimized. With I− in-situ passivated on the surfaces, the spherical HgTe quantum dots are successfully synthesized with the tunability size from 8 to 15 nm. The noise current density of the photoconductive device is as low as 10−11 A·Hz−1/2 at 130 K with a frequency of 1 Hz.

The impact of chemical composition of halide surface ligands on the electronic structure and stability of lead sulfide quantum dot materials

There is a high fundamental interest in the surface and bulk chemistry of quantum dot (QD) solids, as they have proven to be very promising materials in optoelectronic devices. The choice of surface ligands for quantum dots in solid devices determines many of the film properties, as the ligands influence for example the doping density, chemical stability and charge transport. Lead halide ligands have developed as the main ligand of choice for lead sulfide quantum dots, as they have been shown to passivate quantum dot surfaces and enhance the chemical stability. In this study, we successfully varied the ligand composition on the surface of PbS quantum dot films from pure lead iodide to pure lead bromide and investigated its influence on the chemical and electronic structure of the QD solids using hard X-ray photoelectron spectroscopy (HAXPES). Furthermore, we developed a surface treatment to prevent the surface oxidation of a bulk PbS reference sample. Through measurements of this sample and of lead halide reference samples, we were able to assign the contributions of different chemical bonding to the Pb 4f core level and of different atomic orbitals to the valence band spectral shape of the QD materials. Overall, we found that the valence band edge position was very similar for all different iodide:bromide ratios and that all investigated compositions were able to protect the quantum dot surfaces within solid films from oxidation. However, the ligand composition significantly influences the sample stability under X-rays. The iodide rich QD solids showed the highest stability with very little to no chemical changes over several hours of X-ray exposure, while the bromide rich QD solids changed already within the first hour of exposure.

Kinetic Control for Continuously Tunable Lattice Parameters, Size, and Composition during CsPbX3 (X = Cl, Br, I) Nanorod Synthesis

The fast kinetics of all-inorganic CsPbX₃ (X = Cl, Br, or I) nanocrystal growth entail that many synthetic strategies for structural control established in other semiconductor systems do not apply. Rather, products are often determined by thermodynamic factors, limiting the range of synthetic outcomes and functionality. In this study, we show how reaction kinetics are significantly slowed if nanocrystals are prepared using a dual injection strategy that moderates the crucial interaction between cesium and halide during nucleation and growth. The result is highly uniform nanorod or cuboid nanocrystals with a controllable size and aspect ratio across the quantum confinement regime, obtainable for both pure and mixed halide compositions. Further, the crystal lattice is continuously tunable between the tetragonal (I4/mcm) and orthorhombic (Pbnm) phases, independent of the overall nanorod morphology, enabling significantly more sophisticated structure-property relationships that can be tailored during this kinetically controlled synthesis.

Emerging Roles of Green-Synthesized Chalcogen and Chalcogenide Nanoparticles in Cancer Theranostics

The last few decades have seen an overwhelming increase in the amount of research carried out on the use of inorganic nanoparticles. More fascinating is the tremendous progress made in the use of chalcogen and chalcogenide nanoparticles in cancer theranostics. These nanomaterials, which were initially synthesized through chemical methods, have now been efficiently produced using different plant materials. The paradigm shift towards the biogenic route of nanoparticle synthesis stems from its superior advantages of biosafety, eco-friendliness, and simplicity, among others. Despite a large number of reviews available on inorganic nanoparticle synthesis through green chemistry, there is currently a dearth of information on the green synthesis of chalcogens and chalcogenides for cancer research. Nanoformulations involving chalcogens such as sulfur, selenium, and tellurium and their respective chalcogenides have recently emerged as promising tools in cancer therapeutics and diagnosis. Similar to other inorganic nanoparticles, chalcogens and chalcogenides have been synthesized using plant extracts and their purified biomolecules. In this review, we provide an up-to-date discussion of the recent progress that has been made in the plant-mediated synthesis of chalcogens and chalcogenides with a special focus on their application in cancer theranostics.

Mid-IR Intraband Photodetectors with Colloidal Quantum Dots

In this paper, we investigate an intraband mid-infrared photodetector based on HgSe colloidal quantum dots (CQDs). We study the size, absorption spectra, and carrier mobility of HgSe CQDs films. By regulating the time and temperature of the reaction during synthesis, we have achieved the regulation of CQDs size, and the number of electrons doped in conduction band. It is experimentally verified by the field effect transistor measurement that dark current is effectively reduced by a factor of 10 when the 1Se state is doped with two electrons compared with other doping densities. The HgSe CQDs film mobility is also measured as a function of temperature the HgSe CQDs thin film detector, which could be well fitted by Marcus Theory with a maximum of 0.046 ± 0.002 cm2/Vs at room temperature. Finally, we experimentally discuss the device performance such as photocurrent and responsivity. The responsivity reaches a maximum of 0.135 ± 0.012 A/W at liquid nitrogen temperature with a narrow band photocurrent spectrum.

Plant-Based Structures as an Opportunity to Engineer Optical Functions in Next-Generation Light Management

This review addresses the reconstruction of structural plant components (cellulose, lignin, and hemicelluloses) into materials displaying advanced optical properties. The strategies to isolate the main building blocks are discussed, and the effects of fibrillation, fibril alignment, densification, self-assembly, surface-patterning, and compositing are presented considering their role in engineering optical performance. Then, key elements that enable lignocellulosic to be translated into materials that present optical functionality, such as transparency, haze, reflectance, UV-blocking, luminescence, and structural colors, are described. Mapping the optical landscape that is accessible from lignocellulosics is shown as an essential step toward their utilization in smart devices. Advanced materials built from sustainable resources, including those obtained from industrial or agricultural side streams, demonstrate enormous promise in optoelectronics due to their potentially lower cost, while meeting or even exceeding current demands in performance. The requirements are summarized for the production and application of plant-based optically functional materials in different smart material applications and the review is concluded with a perspective about this active field of knowledge.

Nanomaterials for fluorescent detection of curcumin

Owing to the attractive biological and pharmacological activities, sensitive and selective detection of curcumin is of great significance. Nanomaterials possessing unique optical properties exhibit potential applications in the fluorescent detection of curcumin. This review first discussed the detection strategies of fluorescent nanosensors. In the subsequent section, we highlighted the recent advances of different nanomaterials for fluorescent detection of curcumin, including semiconductor QDs, lanthanide upconversion nanoparticles, fluorescent metal nanoclusters, and carbon quantum dots. And we further provided the merits of fluorescent nanosensors for curcumin. Lastly, the challenges and further directions were presented.

Application of nanotechnology in medical diagnosis and imaging

Nanotechnology has tremendously impacted the advancement in imaging, early detection, diagnosis, and prognosis of diseases by improving upon existing clinically relevant technologies. The unique biophysical properties of the nanoparticles enable contrast enhancement to improve biomedical imaging while our ability to manipulate nanoparticles for molecular level specificity enables tissue-specific diagnosis. Importantly, subtle variation in size or composition of the nanoparticles can result in great changes in their optical, magnetic or electrical properties that allows unique possibility of multiplexing. This concise but focused review summarizes the important classes of nanoparticles that have been actively used in improving our ability to image diseased tissues and have contributed to develop technologies that has led to early detection and diagnosis of diseases.

Silver chalcogenide nanoparticles: a review of their biomedical applications

Silver chalcogenide (Ag2X, where X = S, Se, or Te) nanoparticles have been extensively investigated for their applications in electronics but have only recently been explored for biomedical applications. In the past 10 years, Ag2X, primarily silver sulfides at first, have become of great importance as quantum dots, since they not only possess excellent deep tissue imaging properties in the near-infrared regions I and II, but also have low toxicities. Their appealing properties have led to numerous recent developments of Ag2X for biomedical applications. Furthermore, Ag2X have been discovered in the past 2-3 years to be potent X-ray contrast agents, adding to the numerous biomedical uses of these nanoparticles. In this review, we discuss the most recent advances in silver chalcogenide nanoparticle use in areas such as bio-imaging, theranostics, and biosensors. Moreover, we examine the advances in synthetic approaches for these nanoparticles, which include aqueous and organic syntheses routes. Finally, we discuss the advantages and current limitations in the use of silver chalcogenides for different biomedical applications and their potential for advancement and expansions in use.

Solvent-Dependent Photophysical Properties of a Semiconducting One-Dimensional Silver Cluster-Assembled Material

Unraveling the total structure of the atom-precise silver cluster-assembled materials (CAMs) is extremely significant to elucidating the structure-property correlation, but it is a very challenging task. Herein, a new silver CAM is synthesized by a facile synthetic pathway with a unique distorted elongated square-bipyramid-based Ag₁₁ core geometry. The core is protected by two different kinds of the surface protecting ligands (adamantanethiolate and trifluoroacetate) and connected through a bidentate organic linker. The crystallographic data show that this material embraces a one-dimensional periodic structure that orchestrates by various noncovalent interactions to build a thermally stable supramolecular assembly. Further characterization confirms its n-type semiconducting property with an optical band gap of 1.98 eV. The impact of an adamantanethiol-protected silver core on the optical properties of this type of periodic framework is analyzed by the UV-vis absorbance and emission phenomena. Theoretical calculations predicted that the occupied states are majorly contributed by Ag-S. Solvent-dependent photoluminescence studies proved that a polar solvent can significantly perturb the metal thiolate and thiolate-centered frontier molecular orbitals that are involved in the electronic transitions.

Water-Soluble High-Quality Ag2Te Quantum Dots Prepared by Mutual Adaptation of Synthesis and Surface Modification for In Vivo Imaging

Near-infrared (NIR) in vivo fluorescence imaging has exhibited the distinct advantage of high optical resolution at deeper penetration into biological tissues. Ag₂Te quantum dots (QDs), with a relatively narrow band gap, show great promise for fluorescence emission at long wavelengths in the second near-infrared (NIR-II) window for bioimaging. However, existing Ag₂Te QDs have severely hindered the application of in vivo bioimaging due to their poor fluorescence brightness and stability, so it is important to prepare Ag₂Te QDs with high quantum yield and stability as well as high biocompatibility in the NIR-II window. Herein, we designed an integrated method for the preparation of water-soluble Ag₂Te QDs by mutual adaptation of QD synthesis and surface modification. We first synthesized high-quality Ag₂Te QDs with different NIR-II emission wavelengths and the photoluminescence quantum yields (PLQYs) up to 6.51% by rapidly injecting the TBP-Te precursor into a hot solvent to form a highly fluorescent Ag₂Te core. Then water-dispersible Ag₂Te QDs were obtained by direct exchange of the hydrophobic Ag₂Te QD surface ligands with thiol ligands. The PLQY of the water-soluble Ag₂Te QDs obtained by this method can still be maintained at 4.94%. With these highly bright and stable Ag₂Te QDs, the abdominal vessels, hindlimb arterial vessels, venous vessels, sacral lymph nodes, and tumor vessels were visualized non-invasively in vivo in the NIR-II window in mice. The results demonstrate that the integrated strategy of QD synthesis and modification provides valuable technical support for further in-depth applications of Ag₂Te QDs.

Au-Doped Ag2 Te Quantum Dots with Bright NIR-IIb Fluorescence for In Situ Monitoring of Angiogenesis and Arteriogenesis in a Hindlimb Ischemic Model

Fluorescence located in 1500-1700 nm (denoted as the near-infrared IIb window, NIR-IIb) has drawn great interest for bioimaging, owing to its ultrahigh tissue penetration depth and spatiotemporal resolution. Therefore, NIR-IIb fluorescent probes with high photoluminescence quantum yield (PLQY) and stability along with high biocompatibility are urgently pursued. Herein, a novel NIR-IIb fluorescent probe of Au-doped Ag₂ Te (Au:Ag₂ Te) quantum dots (QDs) is developed via a facile cation exchange method. The Au dopant concentration in the Ag₂ Te QDs is tunable from 0% to 10% by controlling the ratio of supplied Au precursor to Ag₂ Te QDs, resulting in a wide range of PL emission in the NIR-IIb window and a much-enhanced PL intensity. After surface modification, the Au:Ag₂ Te QDs possess bright NIR-IIb emission, high colloidal stability and photostability, and decent biocompatibility. Further, in vivo monitoring of the process of angiogenesis and arteriogenesis in an ischemic hindlimb is successfully performed.

Photoluminescent Nanoparticles for Chemical and Biological Analysis and Imaging

Research related to the development and application of luminescent nanoparticles (LNPs) for chemical and biological analysis and imaging is flourishing. Novel materials and new applications continue to be reported after two decades of research. This review provides a comprehensive and heuristic overview of this field. It is targeted to both newcomers and experts who are interested in a critical assessment of LNP materials, their properties, strengths and weaknesses, and prospective applications. Numerous LNP materials are cataloged by fundamental descriptions of their chemical identities and physical morphology, quantitative photoluminescence (PL) properties, PL mechanisms, and surface chemistry. These materials include various semiconductor quantum dots, carbon nanotubes, graphene derivatives, carbon dots, nanodiamonds, luminescent metal nanoclusters, lanthanide-doped upconversion nanoparticles and downshifting nanoparticles, triplet-triplet annihilation nanoparticles, persistent-luminescence nanoparticles, conjugated polymer nanoparticles and semiconducting polymer dots, multi-nanoparticle assemblies, and doped and labeled nanoparticles, including but not limited to those based on polymers and silica. As an exercise in the critical assessment of LNP properties, these materials are ranked by several application-related functional criteria. Additional sections highlight recent examples of advances in chemical and biological analysis, point-of-care diagnostics, and cellular, tissue, and in vivo imaging and theranostics. These examples are drawn from the recent literature and organized by both LNP material and the particular properties that are leveraged to an advantage. Finally, a perspective on what comes next for the field is offered.

Simultaneous Conduction and Valence Band Regulation of Indium-Based Quantum Dots for Efficient H2 Photogeneration

Indium-based chalcogenide semiconductors have been served as the promising candidates for solar H₂ evolution reaction, however, the related studies are still in its infancy and the enhancement of efficiency remains a grand challenge. Here, we report that the photocatalytic H₂ evolution activity of quantized indium chalcogenide semiconductors could be dramatically aroused by the co-decoration of transition metal Zn and Cu. Different from the traditional metal ion doping strategies which only focus on narrowing bandgap for robust visible light harvesting, the conduction and valence band are coordinately regulated to realize the bandgap narrowing and the raising of thermodynamic driving force for proton reduction, simultaneously. Therefore, the as-prepared noble metal-free Cu_0.4-ZnIn₂S₄ quantum dots (QDs) exhibits extraordinary activity for photocatalytic H₂ evolution. Under optimal conditions, the Cu_0.4-ZnIn₂S₄ QDs could produce H₂ with the rate of 144.4 μmol h⁻¹ mg⁻¹, 480-fold and 6-fold higher than that of pristine In₂S₃ QDs and Cu-doped In₂S₃ QDs counterparts respectively, which is even comparable with the state-of-the-art cadmium chalcogenides QDs.

Dithiocarbamate Complexes as Single Source Precursors to Nanoscale Binary, Ternary and Quaternary Metal Sulfides

Nanodimensional metal sulfides are a developing class of low-cost materials with potential applications in areas as wide-ranging as energy storage, electrocatalysis, and imaging. An attractive synthetic strategy, which allows careful control over stoichiometry, is the single source precursor (SSP) approach in which well-defined molecular species containing preformed metal-sulfur bonds are heated to decomposition, either in the vapor or solution phase, resulting in facile loss of organics and formation of nanodimensional metal sulfides. By careful control of the precursor, the decomposition environment and addition of surfactants, this approach affords a range of nanocrystalline materials from a library of precursors. Dithiocarbamates (DTCs) are monoanionic chelating ligands that have been known for over a century and find applications in agriculture, medicine, and materials science. They are easily prepared from nontoxic secondary and primary amines and form stable complexes with all elements. Since pioneering work in the late 1980s, the use of DTC complexes as SSPs to a wide range of binary, ternary, and multinary sulfides has been extensively documented. This review maps these developments, from the formation of thin films, often comprised of embedded nanocrystals, to quantum dots coated with organic ligands or shelled by other metal sulfides that show high photoluminescence quantum yields, and a range of other nanomaterials in which both the phase and morphology of the nanocrystals can be engineered, allowing fine-tuning of technologically important physical properties, thus opening up a myriad of potential applications.

Interplay of Bright Triplet and Dark Excitons Revealed by Magneto-Photoluminescence of Individual PbS/CdS Quantum Dots

A low-temperature polarization-resolved magneto-photoluminescence experiment is performed on individual PbS/CdS core/shell quantum dots (QDs). The experiment enables a direct measurement of the exciton Landé g factor and the anisotropic zero-field splitting of the lowest emissive bright exciton triplet in PbS/CdS QDs. While anisotropic splittings of individual QDs distribute randomly in 104-325 μeV range, the exciton Landé g factors increase from 0.95 to 2.70 as the emission energy of the QD increases from 1.0 to 1.2 eV. The tight-binding calculations allow to rationalize these trends as a direct consequence of reducing a cubic symmetry of QD via addition/removal of a few (<70) atoms from the surfaces of the PbS core. Furthermore, it is observed that while right (σ  ⁺ ) and left (σ   ^- ) circularly polarized photoluminescence (PL) peaks split linearly with magnetic field as expected for Zeeman effect, the energy splitting between X and Y linearly polarized PL peaks remains nearly unchanged. The theoretical study reveals rich and complex magnetic field-induced interplay of bright triplet and dark exciton states explaining this puzzling behavior. These findings fill the missing gaps in the understanding of lead salt QDs and provide foundation for development of classical and quantum light sources operating at telecommunication wavelengths.

NIR-quantum dots in biomedical imaging and their future

Fluorescence imaging has gathered interest over the recent years for its real-time response and high sensitivity. Developing probes for this modality has proven to be a challenge. Quantum dots (QDs) are colloidal nanoparticles that possess unique optical and electronic properties due to quantum confinement effects, whose excellent optical properties make them ideal for fluorescence imaging of biological systems. By selectively controlling the synthetic methodologies it is possible to obtain QDs that emit in the first (650-950 nm) and second (1000-1400 nm) near infra-red (NIR) windows, allowing for superior imaging properties. Despite the excellent optical properties and biocompatibility shown by some NIR QDs, there are still some challenges to overcome to enable there use in clinical applications. In this review, we discuss the latest advances in the application of NIR QDs in preclinical settings, together with the synthetic approaches and material developments that make NIR QDs promising for future biomedical applications.

Self-assembly of colloidal inorganic nanocrystals: nanoscale forces, emergent properties and applications

The self-assembly of colloidal nanoparticles has made it possible to bridge the nanoscopic and macroscopic worlds and to make complex nanostructures. The nanoparticle-mediated assembly enables many potential applications, from biodetection and nanomedicine to optoelectronic devices. Properties of assembled materials are determined not only by the nature of nanoparticle building blocks, but also by spatial positions of nanoparticles within the assemblies. A deep understanding of nanoscale interactions between nanoparticles is a prerequisite to controlling nanoparticle arrangement during assembly. In this review, we present an overview of interparticle interactions governing their assembly in a liquid phase. Considerable attention is devoted to examples that illustrate nanoparticle assembly into ordered superstructures using different types of building blocks, including plasmonic nanoparticles, magnetic nanoparticles, lanthanide-doped nanophosphors, and quantum dots. We also cover the physicochemical properties of nanoparticle ensembles, especially those arising from particle coupling effects. We further discuss future research directions and challenges in controlling self-assembly at a level of precision that is most crucial to technology development.

High-speed and high-precision PbSe/PbI2 solution process mid-infrared camera

Infrared (IR) cameras based on semiconductors grown by epitaxial methods face two main challenges, which are cost and operating at room temperature. The alternative new technologies which can tackle these two difficulties develop new and facile material and methods. Moreover, the implementation of high speed camera, which makes high resolution images with normal methods, is very expensive. In this paper, a new nanostructure based on a cost-effective solution processed technology for the implementation of the high-speed mid-infrared light camera at room temperature is proposed. To this end, the chemically synthesized PbSe-PbI2 core-shell Quantum Dots (QDs) are used. In this work, a camera including 10 × 10 pixels is fabricated and synthesized QDs spin-coated on interdigitated contact (IDC) and then the fabricated system passivated by epoxy resin. Finally, using an electronic reading circuit, all pixels are converted to an image on the monitor. To model the fabricated camera, we solved Schrodinger-Poisson equations self consistently. Then output current from each pixel is modeled based on semiconductor physics and dark and photocurrent, as well as Responsivity and Detectivity, are calculated. Then the fabricated device is examined, and dark and photocurrents are measured and compared to the theoretical results. The obtained results indicate that the obtained theoretical and measured experimental results are in good agreement together. The fabricated detector is high speed with a rise time of 100 ns. With this speed, we can get 10 million frames per second; this means we can get very high-resolution images. The speed of operation is examined experimentally using a chopper that modulates input light with 50, 100, 250, and 500 Hz. It is shown that the fabricated device operates well in these situations, and it is not limited by the speed of detector. Finally, for the demonstration of the proposed device operation, some pictures and movies taken by the camera are attached and inserted in the paper.

Lab-on-Microsphere-FRET-Based Multiplex Sensor Platform

Here we report on the development and investigation of a novel multiplex assay model based on polymer microspheres (PMS) encoded with ternary AIS/ZnS quantum dots (QDs). The system was prepared via layer-by-layer deposition technique. Our studies of Förster resonance energy transfer (FRET) between the QD-encoded microspheres and two different cyanine dyes have demonstrated that the QD photoluminescence (PL) quenching steadily increases with a decrease in the QD-dye distance. We have found that the sensitized dye PL intensity demonstrates a clear maximum at two double layers of polyelectrolytes between QDs and Dye molecules on the polymer microspheres. Time resolved PL measurements have shown that the PL lifetime decreases for the QDs and increases for the dyes due to FRET. The designed system makes it possible to record spectrally different bands of FRET-induced dye luminescence with different decay times and thereby allows for the multiplexing by wavelength and photoluminescence lifetimes of the dyes. We believe that PMS encoded with AIS/ZnS QDs have great potential for the development of new highly selective and sensitive sensor systems for multiplex analysis to detect cell lysates and body fluids' representative biomarkers.

Graphene, an epoch-making material in RFID technology: a detailed overview

Many researchers claim that graphene, a specially studied carbon allotrope, has a single layer of atoms organized in a two-dimensional honeycomb lattice.

Resonant plasmon enhancement of light emission from CdSe/CdS nanoplatelets on Au nanodisk arrays

Semiconducting nanoplatelets (NPLs) have attracted great attention due to the superior photophysical properties compared to their quantum dot analogs. Understanding and tuning the optical and electronic properties of NPLs in a plasmonic environment is a new paradigm in the field of optoelectronics. Here, we report on the resonant plasmon enhancement of light emission including Raman scattering and photoluminescence from colloidal CdSe/CdS nanoplatelets deposited on arrays of Au nanodisks fabricated by electron beam lithography. The localized surface plasmon resonance (LSPR) of the Au nanodisk arrays can be tuned by varying the diameter of the disks. In the case of surface-enhanced Raman scattering (SERS), the Raman intensity profile follows a symmetric Gaussian shape matching the LSPR of the Au nanodisk arrays. The surface-enhanced photoluminescence (SEPL) profile of NPLs, however, follows an asymmetric Gaussian distribution highlighting a compromise between the excitation and emission enhancement mechanisms originating from energy transfer and Purcell effects. The SERS and SEPL enhancement factors depend on the nanodisk size and reach maximal values at 75 and 7, respectively, for the sizes, for which the LSPR energy of Au nanodisks coincides with interband transition energies in the semiconductor platelets. Finally, to explain the origin of the resonant enhancement behavior of SERS and SEPL, we apply a numerical simulation to calculate plasmon energies in Au nanodisk arrays and emission spectra from NPLs in such a plasmonic environment.

Defect studies on short-wave infrared photovoltaic devices based on HgTe nanocrystals/TiO2 heterojunction

Narrow bandgap (<0.5 eV) colloidal semiconductor nanocrystals (e.g. mercury chalcogenides) provide practical platforms for next generation short wave infrared, mid wave infrared and long wave infrared optoelectronic devices. Until now, most of the efforts in the field of infrared active nanocrystals have been taken on synthesizing nanocrystals, determining quantum states and building different geometries for optoelectronic devices. However, studies on interface trap states in the devices made from these narrow band gap nanocrystals are mostly unexplored. Herein, we investigate the defects or traps in these nanocrystals-embedded devices, which will be critical for improving their optoelectronic performance. In this article, we fabricate HgTe nanocrystals/TiO₂ based photovoltaic devices and used capacitance-voltage (C-V) and deep level transient spectroscopy (DLTS) to investigate and obtain quantitative information on deep level trap states. Interestingly, frequency dependent C-V measurements show two peaks in the capacitance at lower frequency (<40 kHz), which is attributed to the presence of trap states. However, at high frequency the presence of a weak hump-like structure almost at the center of above two peaks validate the role of interface traps. DLTS studies show that traps at the interface of HgTe nanocrystals/TiO₂ acts as recombination centers having activation energies of 0.27, 0.4 and 0.45 eV with corresponding trap densities of 1.4 [Formula: see text], 1.[Formula: see text] and 1.[Formula: see text] and estimated capture cross-sections of 6.3 [Formula: see text], 7.5 [Formula: see text] and 3.7 [Formula: see text], respectively. In this work, DLTS has revealed the existence of interface trap states and the frequency dependent capacitance measurements corroborate the effect of charge storage on the heterostructures built from these nanocrystals that helps in the development of futuristic devices.