Synthesis of amino-functionalized nanocellulose by guanidine based deep eutectic solvent and its application in fine fibers retention

A guanidine-based Deep Eutectic Solvent (DES) consisting of 1,3-diaminoguanidine monohydrochloride and glycerol was utilized to prepare C-CNC from dissolving pulp. The pulp fibers were oxidized to dialdehyde cellulose by periodate, then fibrillated through the hydrogen bonds shear of DES and aminocationized through Schiff base effect of the amino groups in the DES solvent to obtain C-CNC. The results revealed that the characterization of the DES (such as viscosity, polarity, and pH) was related to the molar ratio of glycerol/guanidine-salts. The hydrogen bond network structure of DES solvent with optimal system was simulated by DFT and its damage to fiber hydrogen bond network was predicted. The C-CNC produced under the optimal reaction conditions (molar ratio of 1:2, 90 °C for 2 h) was highly dispersible with an average length and diameter of 85 ± 35 nm and 5.0 ± 1.2 nm, a charge density of 2.916 mol/g. C-CNC exhibited excellent flocculation when added to fine fiber suspensions of chemomechanical slurries, achieving rapid flocculation and settling onto fibers in <1 min. The DES solvent maintained its reactivity after 5 cycles. This study lays the foundation for the batch preparation of nanocellulose in an environmentally friendly manner and its application as a green additive in paper industry.

Acetylation of Nanocellulose: Miscibility and Reinforcement Mechanisms in Polymer Nanocomposites

The improvement of properties in nanocomposites obtained by topochemical surface modification, e.g., acetylation, of the nanoparticles is often ascribed to improved compatibility between the nanoparticle and the matrix. It is not always clear however what is intended: specific interactions at the interface leading to increased adhesion or the miscibility between the nanoparticle and the polymer. In this work, it is demonstrated that acetylation of cellulose nanocrystals greatly improves mechanical properties of their nanocomposites with polycaprolactone. In addition, molecular dynamics simulations with a combination of potential of mean force calculations and computational alchemy are employed to analyze the surface energies between the two components. The work of adhesion between the two phases decreases with acetylation. It is discussed how acetylation can still contribute to the miscibility, which leads to a stricter use of the concept of compatibility. The integrated experimental-modeling toolbox used has wide applicability for assessing changes in the miscibility of polymer nanocomposites.

Single-Step Inkjet-Printed Dielectric Template for Large Area Flexible Signage and Low-Information Displays

In recent years, the proliferation of smart gadgets has increased the demand for information displays; fortunately, organic light-emitting diodes (OLEDs) show great promise for use in display, lighting, and signage contexts. This research demonstrates inkjet printing of dielectric materials to provide maskless emission area patterning and electrical isolation for large-area OLEDs on flexible/rigid indium tin oxide (ITO)-coated substrates, avoiding the need for typical photolithography steps, including etching and lift-off processes. We have studied the impact of impinged droplets' velocity fluctuations, which are measured in relation to their interaction with the substrate, allowing for the determination of the drop diameter and shape. The inkjet parameters, such as pulse waveform, pulse voltage, and pulse width, are controlled to provide consistently repeatable ejection of dielectric ink droplets. The single-step patterning of complex designs with a minimum opening of 18 μm features is successfully printed with high fidelity. The effect of substrate temperature on the printed template/structure size and shape is explored. We have successfully demonstrated an ultralarge-area (120 × 120 mm2) OLED signage application on inkjet-printed dielectric template (IJPDt). Standard small-area OLEDs (4 × 4 mm2) achieved a maximum brightness of 24480 cd m-2 at 10 V and a maximum current efficiency of 17 cd A-1 with a low turn-on voltage of 2.7 V.

Performance of Washing-Free Printing of Disperse Dye Inks: Influence of Water-Borne Polymers

Dye-containing wastewater discharge from the textile industry poses a serious pollution hazard that can be overcome by eliminating the washing step following the dyeing process. To study the washing-free printing of disperse dye ink, a number of water-borne polymers were selected and added to the ink, and the properties of the inks were discussed. By optimizing the ink formulation, printed fabrics with high color strength and color fastness were produced. The effects of the addition of polyvinylpyrrolidone (PVP), polyvinyl alcohol (PVA), and polyethylene glycol (PEG) on the ink jetting performance and printing performance were intensively investigated. The migration–diffusion–fixation behavior of disperse dyes in inks on the polyester fiber was explored. The disperse dye ink with 0.075 wt.% PVA exhibited the strongest migration–diffusion effect. The PVA ink exhibited excellent jetting performance and printing color fastness, and the printing color strength was better than that of the PVP and PEG ink. The addition of PVA increased the difference between the solubility parameter of the disperse dyes and ink system, which improved the migration of disperse dyes from the ink system to the polyester fabric. Meanwhile, PVA could form a protective layer on printed fabrics because of its excellent film-forming properties at room temperature. The washing-free inkjet printing method developed in this study provides a theoretical basis for screening water-borne polymers and an environmentally friendly pathway for the printing of textiles.

The State-Of-The-Art Functionalized Nanomaterials for Carbon Dioxide Separation Membrane

Nanocomposite membrane (NCM) is deemed as a practical and green separation solution which has found application in various fields, due to its potential to delivery excellent separation performance economically. NCM is enabled by nanofiller, which comes in a wide range of geometries and chemical features. Despite numerous advantages offered by nanofiller incorporation, fabrication of NCM often met processing issues arising from incompatibility between inorganic nanofiller and polymeric membrane. Contemporary, functionalization of nanofiller which modify the surface properties of inorganic material using chemical agents is a viable approach and vigorously pursued to refine NCM processing and improve the odds of obtaining a defect-free high-performance membrane. This review highlights the recent progress on nanofiller functionalization employed in the fabrication of gas-separative NCMs. Apart from the different approaches used to obtain functionalized nanofiller (FN) with good dispersion in solvent and polymer matrix, this review discusses the implication of functionalization in altering the structure and chemical properties of nanofiller which favor interaction with specific gas species. These changes eventually led to the enhancement in the gas separation efficiency of NCMs. The most frequently used chemical agents are identified for each type of gas. Finally, the future perspective of gas-separative NCMs are highlighted.

Effects of Process and Formulation Parameters on Submicron Polymeric Particles Produced by a Rapid Emulsion-Diffusion Method

Emulsification-diffusion method is often used to produce polymeric nanoparticles. However, their numerous and/or lengthy steps make it difficult to use widely. Thus, a modified method using solvent blends (miscible/partially miscible in water, 25–100%) as the organic phases to overcome these disadvantages and its design space were investigated. To further simplify the process, no organic/aqueous phase saturation and no water addition after the emulsification step were performed. Biodegradable (PLGA) or pH-sensitive (Eudragit^® E100) nanoparticles were robustly produced using low/medium shear stirring adding dropwise the organic phase into the aqueous phase or vice versa. Several behaviors were also obtained: lowering the partially water-miscible solvent ratio relative to the organic phase or the poloxamer-407 concentration; or increasing the organic phase polarity or the polyvinyl alcohol concentration produced smaller particle sizes/polydispersity. Nanoparticle zeta potential increased as the water-miscible solvent ratio increased. Poloxamer-407 showed better performance to decrease the particle size (~50 nm) at low concentrations (≤1%, w/v) compared with polyvinyl alcohol at 1–5% (w/v), but higher concentrations produced bigger particles/polydispersity (≥600 nm). Most important, an inverse linear correlation to predict the particle size by determining the solubility parameter was found. A rapid method to broadly prepare nanoparticles using straightforward equipment is provided.

Chemical affinity and dispersibility of boron nitride nanotubes

Boron nitride nanotubes (BNNTs) are electrically insulating nanoparticles that display highly competitive elastic modulus and thermal conductivity. Long presented as potential fillers for nanocomposite applications, their poor dispersibility in most commodity polymers has, however, limited their spread. In this work, the chemical affinity of purified BNNTs, measured in terms of Hansen solubility parameters (HSP), were obtained through sedimentation tests in a wide set of organic solvents, taking into account relative sedimentation time. The parameters obtained were {δ _d; δ _p; δ _h} = {16.8; 10.7; 14.7} ± {0.3; 0.9; 0.3} MPa^1/2, with a Hildebrand parameter, δ _t = 24.7 MPa^1/2 and a sphere radius of 5.4 MPa^1/2. The solubility parameters were determined considering complete dispersion of the purified nanomaterial, as well as the viscosity and density of the host solvent. These factors, combined with the high purity of the BNNTs, are crucial to minimize the uncertainty of the HSP characterization. Such refined values provide necessary insights both to optimize the solvent casting of unmodified BNNTs, and to orient the surface modification efforts that would be needed to integrate these nanomaterials into a wider range of host matrices.

A review on nanocellulose as a lightweight filler of polyolefin composites

Nanocellulose (NC) possesses low density, high aspect ratio, impressive mechanical properties, nanoscale dimensions, which shows huge potential applications as a reinforced filler. Polyolefin (PO), represented by polyethylene (PE) and polypropylene (PP), has been widely used in industries. Recently nanocellulose/polyolefin nanocomposites (NC/PO nanocomposites) have caught more attention from the application of automotive components, aerospace, furniture, building, home appliances, and sport. In this review, the surface modifications of nanocellulose and polyolefin are summarized respectively, such as surface adsorption modification, small molecule modification, and graft copolymerization modification. The common preparations of NC/PO nanocomposites are discussed, including the melting compounding, the solvent casting, and the in-situ polymerization. The lightweight, mechanical properties, and aging-resistant properties of NC/PO nanocomposites are highlighted. Finally, the potentials and challenges for industrial production development of NC/PO nanocomposites are discussed.

Hansen solubility parameters obtained via molecular dynamics simulations as a route to predict siloxane surfactant adsorption

HYPOTHESIS

The Hansen Solubility Parameters (HSP) derived from Molecular Dynamics (MD) simulations can be used as a fast approach to predict surfactants adsorption on a solid surface. Experiments and simulations: We focused on the specific case of siloxane-based surfactants adsorption on silicon oxide surface (SiO₂), encountered in inkjet printing processes. A simplified atomistic model of the SiO₂ surface was designed to enable the computation of its solubility parameter using MD, and to subsequently determine the interactions of the SiO₂ surface with the siloxane-based surfactant and the various solvents employed. Surfactant adsorption was characterized experimentally using contact angle goniometry, ellipsometry, XPS and AFM.

FINDINGS

Comparison of the numerical results with experiments showed that the HSP theory allows to identify the range of solvents that are likely to prevent surfactant adsorption on the SiO₂ surface. The proposed approach indicates that polar solvents, such as acetone and triacetin, which are strongly attracted to the silicon oxide surface might form a shield that prevents siloxane-based surfactants adsorption. This simple approach, can guide the selection of adequate solvents for surfaces and surfactants with specific chemical structures, providing opportunities for controlling interfacial adsorption.

A novel drug–drug coamorphous system without molecular interactions: improve the physicochemical properties of tadalafil and repaglinide

Tadalafil and repaglinide, categorized as BCS class II drugs, have low oral bioavailabilities due to their poorly aqueous solubilities and dissolutions. The aim of this study was to enhance the dissolution of tadalafil and repaglinide by co-amorphization technology and evaluate the storage and compression stability of such coamorphous system. Based on Flory–Huggins interaction parameter (χ ≤ 0) and Hansen solubility parameter (δ_t ≤ 7 MPa^0.5) calculations, tadalafil and repaglinide was predicted to be well miscible with each other. Coamorphous tadalafil–repaglinide (molar ratio, 1 : 1) was prepared by solvent-evaporation method and characterized with respect to its thermal properties, possible molecular interactions. A single T_g (73.1 °C) observed in DSC and disappearance of crystallinity in PXRD indicated the formation of coamorphous system. Principal component analysis of FTIR in combination with Raman spectroscopy and Ss ¹³C NMR suggested the absence of intermolecular interactions in coamorphous tadalafil–repaglinide. In comparison to pure crystalline forms and their physical mixtures, both drugs in coamorphous system exhibited significant increases in intrinsic dissolution rate (1.5–3-fold) and could maintain supersaturated level for at least 4 hours in non-sink dissolution. In addition, the coamorphous tadalafil–repaglinide showed improved stability compared to the pure amorphous forms under long-term stability and accelerated storage conditions as well as under high compressing pressure. In conclusion, this study showed that co-amorphization technique is a promising approach for improving the dissolution rate of poorly water-soluble drugs and for stabilizing amorphous drugs.

The coamorphous tadalafil–repaglinide (molar ratio, 1 : 1) prepared by solvent-evaporation method significantly improve the physicochemical properties of tadalafil and repaglinide.

Application of Multivariate Adaptive Regression Splines (MARSplines) for Predicting Hansen Solubility Parameters Based on 1D and 2D Molecular Descriptors Computed from SMILES String

A new method of Hansen solubility parameters (HSPs) prediction was developed by combining the multivariate adaptive regression splines (MARSplines) methodology with a simple multivariable regression involving 1D and 2D PaDEL molecular descriptors. In order to adopt the MARSplines approach to QSPR/QSAR problems, several optimization procedures were proposed and tested. The effectiveness of the obtained models was checked via standard QSPR/QSAR internal validation procedures provided by the QSARINS software and by predicting the solubility classification of polymers and drug-like solid solutes in collections of solvents. By utilizing information derived only from SMILES strings, the obtained models allow for computing all of the three Hansen solubility parameters including dispersion, polarization, and hydrogen bonding. Although several descriptors are required for proper parameters estimation, the proposed procedure is simple and straightforward and does not require a molecular geometry optimization. The obtained HSP values are highly correlated with experimental data, and their application for solving solubility problems leads to essentially the same quality as for the original parameters. Based on provided models, it is possible to characterize any solvent and liquid solute for which HSP data are unavailable.

Application of Solvent Parameters for Predicting Organogel Formation

Solvents, accounting the majority of the organogel system, have a tremendous impact on the characteristics of gels. To date, there is a large variety of organogel systems; relatively few have been investigated in the field of structure-solvent correlation. Here, a series of solvent parameters were applied to explore the role of solvent effect on network forming and gel property, intending to build the connection between the precise solvent parameter and gel property. Among the solvent parameters, Kamlet-Taft Parameters and Hansen solubility parameters can distinguish specific types of intermolecular interactions, which could correlate solvent parameter with the gel property. From an analysis of the morphologies obtained from POM and SEM, the gelator structure has an impact on its self-assembly. For possible conformations, the gelators were investigated through XRD. The investigation of solvent-property relationship will provide a theoretical basis for controllable drug delivery implants.

An overview of the transport of liquid molecules through structured polymer films, barriers and composites - Experiments correlated to structure-based simulations

Films engineered to control the transport of liquids are widely used through society. Examples include barriers in packaging, wound care products, and controlled release coatings in pharmaceutics. When observed at the macroscopic scale such films commonly appear homogeneous, however, a closer look reveals a complex nano- and microstructure that together with the chemical properties of the different domains control the transport properties. In this review we compare and discuss macroscopic transport properties, measured using the straightforward, yet highly powerful technique "modified Ussing chambers", also denoted side-by-side diffusion cells, for a wide range of structured polymer films and composites. We also discuss and compare the macroscopic observations and conclusions on materials properties with that of lattice Boltzmann simulations of transport properties based on underlying material structure and chemistry. The survey of the field: (i) highlights the use and power of modified Ussing Chambers for determining liquid transport properties of polymer films, (ii) demonstrates the predictability in both directions between macroscopic observations of transport using modified Ussing chambers and structure-based simulations, and (iii) provides experimental and theoretical insights regarding the transport-determining properties of structured polymer films and composites.

Synthesis of organic aerogels with tailorable morphology and strength by controlled solvent swelling following Hansen solubility

We introduce a generalized approach to synthesize aerogels that allows remarkable control over its mechanical properties. The Hansen solubility parameters are used to predict and regulate the swelling properties of the precursor gels and, consequently, to achieve aerogels with tailored density and mechanical properties. As a demonstration, crosslinked organogels were synthesized from cellulose esters to generate aerogels. By determination of Hansen's Relative Energy Difference, it was possible to overcome the limitations of current approaches that solely rely on the choice of precursor polymer concentration to achieve a set of aerogel properties. Hence, from a given concentration, aerogels were produced in a range of mass densities, from 25 to 113 mg/cm3. Consequently, it was possible to tailor the stiffness, toughness and compressive strength of the aerogels, in the ranges between 14-340, 4-103 and 22-373 kPa, respectively. Additionally, unidirectional freeze-drying introduced pore alignment in aerogels with honeycomb morphologies and anisotropy. Interestingly, when the swelling of the polymeric gel was arrested in a non-equilibrium state, it was possible to gain additional control of the property space. The proposed method is a novel and generic solution to achieving full control of aerogel development, which up to now has been an intractable challenge.