Naturally manufactured biochar materials based sensor electrode for the electrochemical detection of polystyrene microplastics

In recent times, microplastics have become a disturbance to both aquatic and terrestrial ecosystems and the ingestion of these particles can have severe consequences for wildlife, aquatic organisms, and even humans. In this study, two types of biochars were manufactured through the carbonization of naturally found starfish (SF-1) and aloevera (AL-1). The produced biochars were utilized as sensing electrode materials for the electrochemical detection of ∼100 nm polystyrene microplastics (PS). SF-1 and AL-1 based biochars were thoroughly analyzed in terms of morphology, structure, and composition. The detection of microplastics over biochar based electrodes was carried out by electrochemical studies. From electrochemical results, SF-1 based electrode exhibited the detection efficiency of ∼0.2562 μA/μM∙cm2 with detection limit of ∼0.44 nM whereas, a high detection efficiency of ∼3.263 μA/μM∙cm2 was shown by AL-1 based electrode and detection limit of ∼0.52 nM for PS (100 nm) microplastics. Process contributed to enhancing the sensitivity of AL-1 based electrode might associate to the presence of metal-carbon framework over biochar's surfaces. The AL-1 biochar electrode demonstrated excellent repeatability and detection stability for PS microplastics, suggesting the promising potential of AL-1 biochar for electrochemical microplastics detection.

Understanding the intermediates and carbon dioxide adsorption of potassium chloride-incorporated graphitic carbon nitride with tailoring melamine and urea as precursors

In this study, we demonstrated the synthesis of potassium chloride (KCl)-incorporated graphitic carbon nitride, (g-C₃N₄, CN) with varying amounts of N-vacancies and pyridinic-N as well as enhanced Lewis basicity, via a single-step thermal polymerization by tailoring the precursors of melamine and urea for carbon oxide (CO₂) capture. Melamine, as a precursor, undergoes a phase transformation into melam and triazine-rich g-C₃N₄, whereas the addition of urea polymerizes the mixture to form melem and heptazine-rich g-C₃N₄ (CN11). Owing to the abundance of pyridinic-N and the high surface area, CN11 adsorbed higher amounts of CO₂ (44.52 μmol m^-2 at 25 °C and 1 bar of CO₂) than those reported for other template-free carbon materials. Spectroscopic analysis revealed that the enhanced CO₂ adsorption is due to the presence of pyridinic-N and Lewis basic sites on the surface. The intermediates of CO₂adsorption, including carbonate and bicarbonate species, attached to the CN samples were identified using in-situ Fourier-transform infrared spectroscopy (FTIR). This work provides insights into the mechanism of CO₂ adsorption by comparing the structural features of the synthesized KCl-incorporated g-C₃N₄ samples_. CN11, with an excellent CO₂ uptake capacity, is viewed as a promising candidate for CO₂ capture and storage.

Hydrolytic Degradation and Bioactivity of Electrospun PCL-Mg-NPs Fibrous Mats

In this work, the in vitro degradation behavior of nanofibers was investigated in phosphate buffer solution (PBS) and simulated body fluid (SBF) to study their degradation behavior, as well as their bioactivity. The degradation was studied at different immersion times in order to evaluate how the presence of Mg-based nanoparticles can affect the degradation in terms of morphology, crystallinity, degradation rate and pH changes, and finally to evaluate the bioactivity of PCL-based electrospun nanofibers. We found that the degradation of the materials takes more than 3 months; however, the presence of nanoparticles seems to have an accelerating effect on the degradation of the electrospun nanofibers based on PCL. In fact, a reduction in diameter of almost 50% was observed with the highest content of both types of nanoparticles and an increase in crystallinity after 296 days of immersion in PBS. Moreover, the carbonyl index was calculated from an FTIR analysis, and a reduction of 20-30% was observed due to the degradation effect. Additionally, the bioactivity of PCL-based electrospun nanofibers was studied and the formation of crystals on the nanofibers surface was detected, except for neat electrospun PCL related to the formation of NaCl and apatites, depending on the amount and type of nanoparticles. The presence of apatites was confirmed by an XRD analysis and FT-IR analysis observing the characteristic peaks; furthermore, the EDX analysis demonstrated the formation of apatites than can be reconducted to the presence of HA when 20 wt% of nanoparticles is added to the PCL electrospun fibers.

Carbon Nanotubes-Based Fuel Cell for Cr(VI) Removal and Electricity Generation

A fuel cell, an energy transducer, can convert chemical energy into electrical energy. In this work, graphite felt (GF) loaded with polypyrrole (PPy) and carboxylic carbon nanotubes (CNTs-COOH) was used as a cathode (GF/PPy/CNTs-COOH) in a double-chamber nonbiofuel cell (D-nBFC) to remove Cr(VI) efficiently. Therein, Na₂S₂O₃ in an alkaline solution and Cr(VI) in a strongly acidic solution were employed as anode and cathode solutions, respectively. An agar salt bridge, consisting of saturated KCl solution, was used to transport ions between the anode and cathode. This system suggested that the removal efficiency of Cr(VI) could reach 99.6%. The maximum current, power, and power density could achieve 136.8 μA, 18.7 μW, and 20.8 mW/m² at 90 min, respectively. Additionally, GF/PPy/CNTs-COOH also had good electrocatalytic stability and reusability after four cycles, which played an important role in the development of the D-nBFC system. Therefore, this study provides an environmentally friendly and efficient method to remove Cr(VI) and generate electricity simultaneously.

Synthesis of OSL nanophosphor Li3B7O12:Mn and its dosimetric properties

The present paper reports the structural, morphological and optical properties of nanophosphor Li₃B₇O₁₂:Mn with an optimised dopant concentration of 0.25 mol% and its surface modification under the irradiation of 250 keV proton beams and gamma photons for ion fluence ranging from 1 × 10¹³ to 6.25 × 10¹⁵ ions cm^-2 and doses from 100 mGy-100 Gy, respectively. This nanophosphor has been synthesised by the high temperature solid state reaction method. Its optical properties are characterised by optically stimulated luminescence (OSL) and thermo luminescence (TL) techniques. This nanophosphor is polycrystalline in nature with a grain size of 40-80 nm confirmed by x-ray diffraction (XRD) and transmission electron microscopy (TEM). The OSL decay and TL glow curve response of the proton beam irradiated samples exhibit significant intensity at a fluence of 2.5 × 10¹⁴ ions cm^-2. Moreover, Li₃B₇O₁₂:Mn displays a linear response for gamma doses in the range of 100 mGy-50 Gy. We have also investigated the reusability and reproducibility of this material. The above study demonstrates that Li₃B₇O₁₂:Mn is a robust and promising candidate for medical proton dosimetry.