Preparation of a novel metal-free polypyrrole-red phosphorus adsorbent for efficient removal of Cr(VI) from aqueous solution

The toxicity and carcinogenicity of Cr(VI) makes it a major threat to the health of animals and people. However, how to efficiently remove Cr(VI) still faces important challenges. In this study, a new metal-free polypyrrole-red phosphorus (PPy-RP) composite is successfully synthesized by in-situ oxidation polymerization for Cr(VI) removal from wastewater. The maximum adsorption capacity (q_m) of Cr(VI) on PPy-RP-1 is 513.2 mg/g when the pH value is 2, which is far superior to RP nanosheets (207.8 mg/g) and PPy (294.9 mg/g). The improved q_m can be ascribe to the good dispersion and increased specific surface area of PPy-RP adsorbent. Encouragingly, PPy-RP adsorbent still exhibits excellent stability after 7 cycles tests without a significant decline in removal efficiency, and remain above 81.4%. Based on the fittings of adsorption isotherms and kinetics, the process conforms to the pseudo-first-order kinetic model and the single-layer adsorption of the Langmuir model with an R² value of 0.98533. The adsorption process is chemical and monolayer. The experimental result demonstrates that the PPy-RP can efficient removal Cr(VI) by electrostatic attraction and complexation reaction (formation of N-Cr(VI) bond) through the PPy on the surface. The results of this study indicate that PPy-RP is a promising adsorbent to remove the Cr(IV).

Adsorption and Desorption Study of Reusable Magnetic Iron Oxide Nanoparticles Modified with Justicia adhatoda Leaf Extract for the Removal of Textile Dye and Antibiotic

The release of tetracycline hydrochloride (TCH) and methylene blue (MB) dye into the aquatic system uncontrollably caused major environmental and health problems; hence, their prevention required serious attention. Adsorption process is now being researched in order to increase adsorption efficiency and reprocess to alleviate environmental issues. The use of magnetic nanoparticle as an adsorbent for wastewater treatment has a lot of prospective. A magnetic iron oxide nanoparticle surface modified by Vasaka (Justicia adhatoda) leaf extract (JA-MIONs) is used to give a fast removal approach for MB dye and TCH antibiotics. Dynamic light scattering, UV-Vis and band gap measurement, powder X-ray diffraction, Fourier-transform infrared spectroscopy, and transmission electron microscopy were operated to analyse the formation and size of these magnetic nanoparticles. The impacts of different factors such as contact time (30-150 min), adsorbate concentration (10-50 mg/L), pH (4-10), and adsorbent dose (2-10 mg) were explored. Adsorption kinetics and isotherms show that it follows the pseudo-first-order kinetic and the Freundlich isotherm, with maximum adsorption capacities of 76.92 mg/g for MB and 200 mg/g for TCH at 298 K. The reusability of the JA-MIONs eventually exhibited a decline in the adsorption percentage of MB and TCH after five and four times respectively. After the desorption-adsorption cycles, this adsorbent continued to exhibit significant adsorption capacity. This investigation furnished the significant reference data for the synthesis of JA-MIONs as a novel and auspicious adsorbent for the industrial clean-up of toxic dyes and heavily used antibiotics from water.

“Gamma Irradiation Synthesis of Carboxymethyl Chitosan-Nanoclay Hydrogel for the Removal of Cr(VI) and Pb(II) from Aqueous Media”

Hydrogel composites comprised of N,O carboxymethyl chitosan crosslinked with different weight ratios of acrylic acid and fabricated with nanoclay particle were prepared via gamma irradiation at 25 kGy irradiation dose. The prepared composites were coded as CsAA1Cl, CsAA2Cl and CsAA3Cl based on the weight ratio of acrylic acid to the chitosan derivative. The claimed hydrogels were characterized by FTIR, TGA and XRD. The TGA data implied that the incorporation of clay nanoparticles enhanced the thermal stability of the composites; the decomposition temperature increased up to 500 °C for CsAA3Cl. Three AFM outcomes were used to compare the surface features of the samples; topography, height and surface roughness. The topography data reveals that the nanoclay particles incorporated in CsAA3Cl are intercalated and exfoliated. Then, the optimized sorbent (CsAA3Cl) was investigated as green sorbents for chromium (VI) and lead (II). The data revealed that CsAA3Cl displayed maximum removal performance towards both lead and chromium with removal efficiencies 125 mg/g and 205 mg/g respectively at the optimum application conditions within 90 min only. Also, it was found that the optimum pH value was 9 for chromium and 8 for lead. The data proved that the adsorption of both cations followed pseudo-first order kinetic model. The prepared composites showed acceptable metal uptake capacity at three successive cycles.

Graphical Abstract

Controlled synthesis of trimetallic nitrogen-incorporated CoNiFe layered double hydroxide electrocatalysts for boosting the oxygen evolution reaction

The development of non-precious trimetallic electrocatalysts exhibiting high activity and stability is a promising strategy for fabricating efficient electrocatalysts for the oxygen evolution reaction (OER). In this study, trimetallic nitrogen-incorporated CoNiFe (N–CoNiFe) was produced to solve the low OER efficiency using a facile co-precipitation method in the presence of ethanolamine (EA) ligands. A series of CoNiFe catalysts at different EA concentrations were also investigated to determine the effects of the ligand in the co-precipitation of a trimetallic system. The introduction of an optimized EA concentration (20 mM) improved the electrocatalytic performance of N–CoNiFe dramatically, with an overpotential of 318 mV at 10 mA cm⁻² in 1.0 M KOH and a Tafel slope of 72.2 mV dec⁻¹. In addition, N–CoNiFe shows high durability in the OER process with little change in the overpotential (ca. 16.0 mV) at 10 mA cm⁻² after 2000 cycles, which was smaller than that for commercial Ir/C (38.0 mV).

A trimetallic nitrogen-incorporated CoNiFe exhibited good catalytic properties toward the oxygen evolution reaction, e.g., high stability and low overpotential (318 mV at 10 mA cm⁻²).

Chromium(VI) Removal from Water by Lanthanum Hybrid Modified Activated Carbon Produced from Coconut Shells

Cr(VI) is considered to be the most hazardous and toxic oxidation state of chromium and hence the development of effective removal technologies, able to provide water with Cr(VI) below the drinking water limits (US EPA 100 μg/L, European Commission 50 μg/L, which will be reduced to 25 by 2036) is a very important issue in water treatment. This study aimed at examining the performance of activated carbon produced from coconut shells, modified by lanthanum chloride, for Cr(VI) removal from waters. The structure of the formed material (COC-AC-La) was characterized by the application of BET, FTIR and SEM techniques. The effect of the adsorbent's dosage, pH value, contact time, initial Cr(VI) concentration and water matrix was examined with respect to Cr(VI) removal. The results indicated that the maximum Cr(VI) removal was observed at pH 5; 4 h contact time and 0.2 g/L of adsorbent's dosage was adequate to reduce Cr(VI) from 100 μg/L to below 25 μg/L. Freundlich isotherm and pseudo-second order kinetic models fitted the experimental data sufficiently. The maximum adsorption capacity achieved was 6.3 μg/g at pH 5. At this pH value, the removal percentage of Cr(VI) reached 95% for an initial Cr(VI) concertation of 30 μg/L. At pH 7 the corresponding efficiency was roughly 60%, resulting in residual Cr(VI) concentrations below the anticipated drinking water limit of 25 μg/L of total chromium, when the initial Cr(VI) concentration was 50 μg/L. Consecutive adsorption and regeneration studies were conducted using 0.01 M of NaOH as an eluent to evaluate the reusability of the adsorbents, Results showed 20% decrease of adsorption capacity after 5 regeneration cycles of operation.

Investigating the selectivity and interference behavior for detoxification of Cr(VI) using lanthanum phosphate polyaniline nanocomposite via adsorption-reduction mechanism

A novel Lanthanum phosphate polyaniline (LaPO₄-PANI) nanocomposite was synthesized by the simple sol-gel technique. The nanocomposite prepared at 1:1 ratio provided the highest ion exchange capacity and selective adsorption of Cr(VI). The phase composition and particle morphology of the as-prepared material was evaluated by XRD, FESEM and TEM analyses. The FTIR, Raman, and TGA data inferred the definite chemical interaction between the organic and inorganic counterparts in the formation of LaPO₄-PANI. The selective adsorption of Cr(VI) was estimated by evaluating the distribution coefficient, electrical double layer theory as well as valency and Pauling's ionic radii of interfering ions (phosphate, iodide, sulfate, chloride, sulfide). The high tolerance capability of LaPO₄-PANI against the interfering ions made it appropriate for selective and efficient removal of Cr(VI) ions from solutions. The nanocomposite showed the highest removal percentage of 98.6% towards Cr(VI) in a wide pH range of 2-6 at room temperature, as compared to sole lanthanum phosphate (56%) and polyaniline (75%). The XPS analysis revealed the adsorption mechanism due to the combined effect of both adsorption and reduction. Cr(VI) is adsorbed through electrostatic interactions while the = N-/-NH- group facilitated the in situ chemical reduction. The procured results make the LaPO₄-PANI nanocomposite a promising adsorbent for the removal of Cr(VI).

Chemico-nanotreatment methods for the removal of persistent organic pollutants and xenobiotics in water - A review

While the technologies available today can generate high-quality water from wastewater, the majority of the wastewater treatment plants are not intended to eliminate emerging xenobiotic pollutants, pharmaceutical and personal care items. Most endocrine disrupting compounds (EDCs) and personal care products (PPCPs) are more arctic than most regulated pollutants, and several of them have acid or critical functional groups. Together with the trace occurrence, EDCs and PPCPs create specific challenges for removal and subsequent improvements of wastewater treatment plants. Various technologies have been investigated extensively because they are highly persistent which leads to bioaccumulation. Researchers are increasingly addressing the human health hazards of xenobiotics and their removal. The emphasis of this review was on the promising methods available, especially nanotechnology, for the treatment of xenobiotic compounds that are accidentally released into the setting. In terms of xenobiotic elimination, nanotechnology provides better treatment than chemical treatments and their degradation mechanisms are addressed.

Adsorption of Lead Ion from Wastewater Using Non-Crystal Hydrated Calcium Silicate Gel

In order to obtain low-cost and excellent adsorption materials, this paper used calcium acetate and water glass as raw materials to synthesis hydrated calcium silicate gel by precipitation method. The performance and structure of hydrated calcium silicate gel were systematically studied by X-ray photoelectron spectroscopy, fourier transform infrared spectroscopy, specific surface area analyzer and scanning electron microscope. Studies have shown that, non-crystal hydrated calcium silicate gel (CSH) were successfully prepared, and the removal rate of lead ion using CSH reached more than 90%. The adsorption process is consistent with the pseudo-second-order kinetic model and Langmuir adsorption isotherm model, and the limit adsorption capacity reaches 263.17 mg·g-1. The acid treatment experiment proved that the adsorption capacity of lead ion using CSH was satisfactory, and the adsorption rate remained at >60% after 5 cycles. The research may provide a low-cost, high-efficiency and high stability adsorbent.

O3 oxidation excited by yellow phosphorus emulsion coupling with red mud absorption for denitration

Directing to unwieldiness NOx emitted by the industry, the removal of NOx was implemented using yellow phosphorus (P₄) emulsion and red mud slurry as composite absorbent. Where yellow phosphorus is considered to stimulate formation of the ecological ozone (O₃) from O₂, the oxidation of insoluble NO into water-soluble NOx species by O₃, and the red mud as a pH buffer can be used to maintain the pH of the absorption liquid in a range that better absorbs NOx. NO is finally converted into NO₂^- and NO₃^-, whereas the yellow phosphorus is mainly PO₄^3-. Single-factor influencing on the efficiency of denitration include the concentration of yellow phosphorus, reaction temperature, stirring intensity, gas flow rate, O₂ content, and red mud solid-liquid ratio were investigated. Response surface methodology (RSM) was used to optimize the process parameters. It was indicated that the removal rate of NOx can reach 99.3% under the optimal conditions. Moreover, the possible denitration reaction mechanism was also discussed.

Calcium oxide modification of activated sludge as a low-cost adsorbent: Preparation and application in Cd(II) removal

In this study, a simple to produce, low-cost and environment-friendly sludge based adsorbent, prepared from municipal dewatered sludge and modified by calcium oxide (CaO), is described. The enhancement effect of CaO modification on the adsorption capacity and mechanical strength of sludge based adsorbents (CaO-SA), and the modification mechanism of CaO on activated sludge are discussed. Also, the Cd(II) adsorption conditions are optimized using surface optimization experiment. The results indicated that CaO had a good effect on improving the adsorption capacity and mechanical strength of the sludge-based adsorbent. The CaO-SA adsorbent showed best performance with respect to the mechanical strength and Cd(II) adsorption capacity when prepared under 5% CaO dosage and 60 °C drying temperature. CaO modification can increase the specific surface area and calcium ion content of the sludge-based adsorbent and remove the proton of the carboxylic acid in the sludge. The Box-Behnken experimental design results revealed that the importance of operating conditions for CaO-SA adsorption of Cd(II) can be arranged in the order of adsorption time > dosage> pH> temperature. The results also indicated that the interactions between adsorption time and CaO-SA dosage, adsorption time and pH, adsorption time and temperature are all important factors affecting the Cd(II) adsorption. The optimal conditions (adsorption time of 90 min, CaO-SA dosage of 1 g/L, pH of 5 and adsorption temperature of 40 °C) for CaO-SA to adsorb Cd(II) were obtained by surface optimization, at which the Cd(II) adsorption rate could reach a value of 99.74%.

Design of 3D alumina-doped magnesium oxide aerogels with a high efficiency removal of uranium(vi) from wastewater

3D alumina-doped magnesium oxide (Al₂O₃/MgO) aerogels with remarkable adsorption properties for U(vi) were prepared via a simple lyophilization–calcination method.

Preparation of a porous carbon material by hydrothermal activation of itaconic acid fermentation waste liquid and its efficient adsorption of Cr(vi)

Recycling organic waste liquid to treat chromium-containing wastewater to achieve the purpose of treating waste with waste.

Field analysis of Cr(vi) in water samples by using a smartphone-based ultralong absorption path reflection colorimetric device

Hexavalent chromium is highly toxic and regarded as one of the main pollutants in the environment. A multiple reflection colorimetric cell is designed to improve the sensitivity in field analysis for Cr(vi).

Facile synthesis of poly o-toluidine modified lanthanum phosphate nanocomposite as a superior adsorbent for selective fluoride removal: A mechanistic and kinetic study

This work reports the synthesis of a new adsorbent material (LaP-POT), synthesised by sol-gel polymerisation method from lanthanum phosphate (LaP) and poly o-toluidine (POT). The sustainability and selectivity of the material as a potential adsorbent is evaluated for the removal of fluoride from aqueous as well as real water samples using batch experimental techniques. FESEM and TEM images showed the successful incorporation of rod-shaped lanthanum phosphate into the poly o-toluidine polymer matrix. The increased degradation temperature of LaP-POT from TGA curve inferred a definite interaction between two. XPS study revealed the successful binding of fluoride onto LaP-POT. The selectivity of fluoride ion onto LaP-POT material was ascertained by the distribution coefficient value. The co-anions showed little effect on fluoride removal. Kinetic study suggested that intraparticle diffusion is not the only rate controlling step; the external mass transfer or chemical interaction also impacts the fluoride adsorption. The maximum adsorption was observed at room temperature with a maximum Langmuir uptake capacity of 10.94 mg g^-1. The reusability of the material is tested up to 5 successive cycles for a workable commercial application purpose. The results showed that LaP-POT provides more active sites, thus making it a promising adsorbent for the removal of fluoride.

Kendu (Diospyros melanoxylon Roxb) fruit peel activated carbon-an efficient bioadsorbent for methylene blue dye: equilibrium, kinetic, and thermodynamic study

In this work, activated carbon was synthesized by the carbonization of kendu fruit peel followed by chemical activation using ammonium carbonate as an activating agent to get modified kendu fruit peel (MKFP). The SEM and FESEM images of the biomaterial illustrated a highly porous honeycomb-like structure, further supported by the N₂ sorption isotherm analysis. The FTIR spectra specified the presence of oxygen-containing functional groups such as carboxyl, carbonyl, and hydroxyl on the adsorbent surface. Batch experiments were performed for the optimization of methylene blue (MB) dye removal. The adsorption process followed pseudo-second-order kinetic model and Langmuir isotherm model with a maximum adsorption capacity of 144.9 mg g^-1. No desorption was found because the adsorbent surface was bonded with the chromophoric group of the MB dye by means of strong chemical interaction evident from the high adsorption energy (E = 10.42 kJ mol^-1) and enthalpy change (∆H = 42.7 kJ mol^-1). Hence, the MKFP has the potential to act as an efficient bioadsorbent for MB dye removal. Graphical abstract.

Adsorptive removal of tetracycline by sustainable ceramsite substrate from bentonite/red mud/pine sawdust

In this study, a novel, sustainable and efficient ceramsite substrate of constructed wetlands (CWs) were prepared for tetracycline (TC) removal by employing bentonite (Ben) and red mud (Rm) as the main materials and pine sawdust (Ps) as the additive. The optimal parameters for Ben/Rm/Ps ceramsite preparation were obtained via orthogonal and one-factor experimental designs, and the optimal parameters were presented as follows: mass ratio of Ben: Rm: Ps = 4:1:0.9, preheating temperature = 240 °C, preheating time = 20 min, calcining temperature = 1150 °C, and calcining time = 14 min. The properties of Ben/Rm/Ps-op ceramsite (obtained at the optimal condition) were first analyzed, including XRD and SEM, and demonstrated a microporous structure with some crystal strength components. Neutral condition and higher temperature were indicated conducive to improve the TC removal efficiency, while coexisting ions (Na⁺ or Ca²⁺) showed adverse effect for TC adsorption by Ben/Rm/Ps-op. In addition, adsorption kinetics and isotherm could be well described by the second-order kinetics and linear isothermal model, respectively, which suggested chemisorption and multilayer adsorption thickness increased infinitely. The theoretical maximum TC adsorption capacity of Ben/Rm/Ps-op at 20 °C reached up to 2.5602 mg/g. In addition, Ben/Rm/Ps-op could effectively remove TC as the CWs substrate under a dynamic flow condition. Further, Ben/Rm/Ps-op exhibited high reusability capability and stability for TC removal, and the adsorption amount still remained for 2.13 mg/g (C₀ = 80 mg/L) after three consecutive cycles.