High performance asymmetric V2O5-SnO2 nanopore battery by atomic layer deposition

Prelithiation Reagents and Strategies on High Energy Lithium-Ion Batteries

Lithium-ion batteries (LIBs) have been widely employed in energy-storage applications owing to the relatively higher energy density and longer cycling life. However, they still need further improvement especially on the energy density to satisfy the increasing demands on the market. In this respect, the irreversible capacity loss (ICL) in the initial cycle is a critical challenge due to the lithium loss during the formation of solid electrolyte interphase (SEI) layer on the anode surface. The strategy of prelithiation was then proposed to compensate for the ICL in the anode and recover the energy density. Here, various methods of the prelithiation are summarized and classified according to the basic working mechanism. Further, considering the critical importance and promising progress of prelithiation in both fundamental research and real applications, this Review article is intended to discuss the considerations involved in the selection of prelithiation reagents/strategies and the electrochemical performance in full-cells. Moreover, insights are provided regarding the practical application prospects and the challenges that still need to be addressed.

Reconfiguring Organosulfur Cathode by Over-Lithiation to Enable Ultrathick Lithium Metal Anode toward Practical Lithium-Sulfur Batteries

An ultrathick lithium metal anode (LMA) is a prerequisite for developing practical lithium-sulfur (Li-S) batteries that simultaneously meet the requirements of high areal capacity, lean electrolyte, and limited excess Li. Inspired by the electrochemical process for an organosulfur cathode, herein, we reconfigure such a sulfur cathode by using an overlithiation strategy to enable the formation of a high performance LMA. Specifically, an applicable ultrathick LMA is successfully constructed by overlithiating a well-known organosulfur cathode material, sulfurized polyacrylonitrile (SPAN). SPAN contains a polymeric pyridine structure with an outstanding lithium-ion affinity, so that it can act as a lithiophilic matrix. More importantly, a Li2S-rich solid electrolyte interphase (SEI) can be generated on the surface of SPAN during the overlithiation process. The synergistic effect of the lithiophilic matrix and a robust SEI leads to a dense deposition of lithium, which enables one to form an ultrathick LMA (159 μm, 30 mAh cm-2) with high Coulombic efficiency (99.7%). Such an LMA paired with a sulfur cathode of high areal capacity (up to 16 mAh cm-2) shows stable cycling under practical conditions of a lean electrolyte (2.2 μL mgS-1) and a negative-to-positive capacity (N/P) ratio as low as 1.3. The applicability of the ultrathick LMA was further verified with Li-S pouch cells, indicating a highly prospective route toward realization of practical Li-S batteries.

Atomic Layer Deposition of SnO2-Coated Anodic One-Dimensional TiO2 Nanotube Layers for Low Concentration NO2 Sensing

The continuous emission of nitrous oxides contributes to the overall air pollution and deterioration of air quality. In particular, an effective NO₂ sensor capable of low concentration detection for continuous monitoring is demanded for safety, health, and wellbeing. The sensing performance of a metal oxide-based sensor is predominantly influenced by the availability of surface area for O₂ adsorption and desorption, efficient charge transport, and size or thickness of the sensing layer. In this study, we utilized anodic one-dimensional (1D) TiO₂ nanotube layers of 5 μm thick which offer large surface area and unidirectional electron transport pathway as a platform to accommodate thin SnO₂ coatings as a sensing layer. Conformal and homogeneous SnO₂ coatings across the entire inner and outer TiO₂ nanotubes were achieved by atomic layer deposition with a controlled thickness of 4, 8, and 16 nm. The SnO₂-coated TiO₂ nanotube layers attained a higher sensing response than a reference Figaro SnO₂ sensor. Specifically, the 8 nm SnO₂-coated TiO₂ nanotube layer has recorded up to ten-fold enhancement in response as compared to the blank nanotubes for the detection of 1 ppm NO₂ at an operating temperature of 300 °C with 0.5 V applied bias. This is attributed to the SnO₂/TiO₂ heterojunction effect and controlled SnO₂ thickness within the range of the Debye length. We demonstrated in this work, a tailored large surface area platform based on 1D nanotubes with thin active coatings as an efficient approach for sensing applications and beyond.

A Novel Biosensor Based on Molybdenum Disulfide (MoS2 ) Modified Porous Anodic Aluminum Oxide Nanochannels for Ultrasensitive microRNA-155 Detection

Artificial photoresponsive nanochannels have attracted widespread attention because of their capacity to achieve ion transport through light modulation. Herein, a biosensor for ultrasensitive miRNA-155 detection is devised based on molybdenum disulfide (MoS₂ ) modified porous anodic aluminum oxide (AAO) photoresponsive nanochannels by atomic layer deposition (ALD). According to the optimized experimental results, when the cycles of ALD, the wavelength, and the power of the excitation laser are 70 cycles, 450 nm, and 80 mW, respectively, the most supreme photocurrent performance of these photoresponsive nanochannels are obtained. AAO nanochannels modified with MoS₂ can work as a photoelectrochemical (PEC) biosensor by generating photoexcitation current; what is more, the high channel density in AAO can magnify the ion current signal response effectively by aggrandizing the flux of electroactive species. By using AAO photoresponsive nanochannels with an average diameter of 150 nm as PEC biosensor, an ultrasensitive detection record ranging from 0.01 fM to 0.01 nM with a detection limit of 3 aM can be achieved. This work not only proposes a simple method for manufacturing semiconductor photoresponsive nanochannels, but also exhibits great potential in the ultrasensitive detection of biomolecules.

Growth of lithium hydride thin films from solutions: Towards solution atomic layer deposition of lithiated films

Lithiated thin films are necessary for the fabrication of novel solid-state batteries, including the electrodes and solid electrolytes. Physical vapour deposition and chemical vapour deposition can be used to deposit lithiated films. However, the issue of conformality on non-planar substrates with large surface area makes them impractical for nanobatteries the capacity of which scales with surface area. Atomic layer deposition (ALD) avoids these issues and is able to deposit conformal films on 3D substrates. However, ALD is limited in the range of chemical reactions, due to the required volatility of the precursors. Moreover, relatively high temperatures are necessary (above 100 °C), which can be detrimental to electrode layers and substrates, for example to silicon into which the lithium can easily diffuse. In addition, several highly reactive precursors, such as Grignard reagents or n-butyllithium (BuLi) are only usable in solution. In theory, it is possible to use BuLi and water in solution to produce thin films of LiH. This theoretical reaction is self-saturating and, therefore, follows the principles of solution atomic layer deposition (sALD). Therefore, in this work the sALD technique and principles have been employed to experimentally prove the possibility of LiH deposition. The formation of homogeneous air-sensitive thin films, characterized by using ellipsometry, grazing incidence X-ray diffraction (GIXRD), in situ quartz crystal microbalance, and scanning electron microscopy, was observed. Lithium hydride diffraction peaks have been observed in as-deposited films by GIXRD. X-ray photoelectron spectroscopy and Auger spectroscopy analysis show the chemical identity of the decomposing air-sensitive films. Despite the air sensitivity of BuLi and LiH, making many standard measurements difficult, this work establishes the use of sALD to deposit LiH, a material inaccessible to conventional ALD, from precursors and at temperatures not suitable for conventional ALD.