Development of an analytical platform that combines a lab-on-gel device with hydrogel layer-based deproteinization/sensing functions and a compact fluorescence imager

An analytical platform was developed using agarose gel to overcome the issues of device miniaturization and interference effects caused by foreign proteins, which are challenges for field analysis-oriented measurement technology. The lab-on-gel (LoG) device integrates sample preparation, reaction, and detection on a chip, with an agarose gel for separation that preferentially allows only small molecules to pass through due to the size exclusion effect, and an agarose gel for sensing that contains glucose dehydrogenase and substrates. Measurements can be performed simply by dropping in a diluted serum sample and then placing the device in a custom-made compact Raspberry Pi-based fluorescence imager. This analytical approach was demonstrated by glucose measurement. The detection limit for glucose was estimated to be 21 μM (3σ). The method was also able to quantify glucose in serum at a lower dilution than the conventional method using well plates. This suggests that agarose gel works effectively for the pretreatment and sensing of biosensors. The developed method is expected to be useful for rapid and labor-saving medical diagnostics in town clinics and at the bedside.

A highly sensitive ion-selective chemiresistive sensor for online monitoring of lead ions in water

Dissolved lead is a serious but common health hazard in drinking water, yet there is still no practical way to monitor its levels continuously in the distribution system or at the point of use. Here we propose using a lead-selective membrane on top of a chemiresistive device to continuously measure Pb2+ ion concentrations in real time. The detection limit was lowered by stabilizing the surface of the resistive film with sodium hydroxide and 15-crown-5 ether and optimizing the sensor geometry to maximize the effective surface area. The detection mechanism is based on the complexation of the Pb2+ ions by the lead ionophores within the membrane, thus modulating the interactions between the ionophores and the chemiresistive film. The limit of detection of the fabricated devices was reliably below 2 μg L-1, with concentrations up to 3 mg L-1 routinely quantifiable over several measurement cycles. The chemiresistive sensors can thus achieve lower detection limits than potentiometric devices while being more robust and simpler to fabricate by omitting the reference electrode. Ion-selective membrane-covered chemiresistors can therefore be deployed to continuously monitor drinking water sources and detect harmful levels of lead in real time.

Visual Gustation via Regulable Elastic Photonic Crystals

The unique structural sensitivity of photonic crystals (PCs) endows them with stretchable or elastic tunability for light propagation and spontaneous emission modulation. Hydrogel PCs have been demonstrated to have biocompatibility and flexibility for potential human health detection and environmental security monitoring. However, current elastic PCs still possess a fixed elastic modulus and uncontrollable structural colors based on a tunable elastic modulus, posing considerable challenges for in situ detection, particularly in wearable or portable sensing devices. In this work, we introduced a novel chemo-mechanical transduction mechanism embedded within a photonic crystal nanomatrix, leading to the creation of structural colors and giving rise to a visual gustation sensing experience. By utilizing the captivating structural colors generated by the hydrogel PC, we employ abundant optical information to identify various analytes. The finite element analysis proved the electric field distribution in the PC matrix during stretch operations. The elastic-optical behaviors with various chemical cosolvents, including cations, anions, saccharides, or organic acids, were investigated. The mechanism of the Hofmeister effect regulating the elasticity of hydrogels was demonstrated with the network nanostructure of the hydrogels. The hydrogel PC matrix demonstrates remarkable capability in efficiently distinguishing a wide range of cations, anions, saccharides, and organic acids across various concentrations, mixtures, and even real food samples, such as tastes and soups. Through comprehensive research, a precise relationship between the structural colors and the elastic modulus of hydrogel PCs has been established, contributing to the biomatching elastic-optics platform for wearable devices, a dynamic environment, and clinical or health monitoring auxiliary.

Near-Infrared Fluoride Sensing Nano-Optodes and Distance-Based Hydrogels Containing Aluminum-Phthalocyanine

Fluoride ions are highly relevant in environmental and biological sciences, and there is a very limited number of established fluoride chemical sensors. Previous fluoride-selective optodes were demonstrated with metal-porphyrin as the ionophore and required a chromoionophore for optical signal transduction. We demonstrate here novel optical fluoride sensing with nano-optodes containing an aluminum-phthalocyanine complex (AlClPc) as the single active sensing component, simplifying the conventional ion-selective optodes approach. The fluoride nano-optodes were interrogated in the absorbance and fluorescence modes in the near-infrared region, with absorption around 725 nm and emission peaks at 720 and 800 nm, respectively. The nano-optodes exhibited a lower detection limit around 0.1 μM and good selectivity over a range of common anions including ClO4-, Cl-, Br-, I-, SO42-, NO3-, and AcO-. Furthermore, the nano-optodes were physically entrapped in agarose hydrogels to allow distance-based point-of-care testing (POCT) applications. The 3D networks of the agarose hydrogel were able to filter off large particulates in the samples without stopping fluoride ions to reach the nano-optodes. The fluoride concentrations in real samples including river water, mineral water, and groundwater were successfully determined with the distance-based sensing hydrogel, and the results agreed well with those from commercial fluoride electrodes. Therefore, the results in this work lay the groundwork for the optical detection of fluoride in environmental samples without very sophisticated sample manipulation.

Optical Detection of Heparin in Whole Blood Samples Using Nanosensors Embedded in an Agarose Hydrogel

Point-of-care quantification of the anticoagulant heparin still remains a significant clinical challenge as the reference method (colorimetric anti-factor Xa assay) cannot be performed in whole blood. Our group recently put forth the novel optical nanosensing principle using an ionic solvatochromic dye as a signal transducer. These nanosensors demonstrated significantly improved selectivity and sensitivity compared to ion-exchange-type polyion nanosensors and enabled protamine/heparin quantification in blood plasma samples. However, because the readout is absorbance-based, they are still not suitable for whole blood measurements. To overcome the background absorbance of blood, the nanosensors were here embedded in an agarose hydrogel capable of filtering out red blood cells while allowing plasma components to diffuse into the gel. Calibration curves for both protamine and heparin were successfully obtained in buffer, undiluted plasma, and undiluted whole blood using different colorimetric image analysis methods and a simple experimental setup.

Fluorescence Anisotropy as a Self-Referencing Readout for Ion-Selective Sensing and Imaging Using Homo-FRET between Chromoionophores

Fluorescence anisotropy has been widely used in developing biosensors and immunoassays, by virtue of the self-reference and environment-sensitive properties. However, fluorescence anisotropic chemical sensors on inorganic ions are limited by the total anisotropy change. To this end, we demonstrate here fluorescence anisotropic ion-selective optodes based on the homo-FRET (Förster resonance energy transfer) of the crowded chromoionophores. The conventional fluorescence on-off mode is transformed into the anisotropic mode. Variation of the target ion concentration changes the inter-chromoionophore distance in the organic sensing phase, leading to different extents of homo-FRET and steady-state anisotropy. A theoretical model is developed by coupling homo-FRET and anisotropy. Anisotropic detections of pH, K⁺, and Na⁺ are demonstrated as examples based on the different ionophores for H⁺, K⁺, and Na⁺, respectively. Further, fluorescence imaging of the nano-optodes, plasticized poly(vinyl chloride) sensing films, and live cells are demonstrated using a homemade fluorescence anisotropic imaging platform. The results form the basis of an ion-selective analytical method operating in the fluorescence anisotropic mode, which could potentially be applied to other fluorescence on-off probes based on homo-FRET.

Perspective on fluorescence cell imaging with ionophore-based ion-selective nano-optodes

Inorganic ions are ubiquitous in all kinds of cells with highly dynamic spatial and temporal distribution. Taking advantage of different types of fluorescent probes, fluorescence microscopic imaging and quantitative analysis of ion concentrations in cells have rapidly advanced. A family of fluorescent nanoprobes based on ionophores has emerged in recent years with the potential to establish a unique platform for the analysis of common biological ions including Na+, K+, Ca2+, Cl-, and so on. This article aims at providing a retrospect and outlook of ionophore-based ion-selective nanoprobes and the applications in cell imaging.

Portable point-of-care diagnostic devices: an updated review

The global pandemic caused by the SARS-CoV-2 (COVID) virus indiscriminately impacted people worldwide with unquantifiable and severe impacts on all aspects of our lives, regardless of socioeconomic status. The pandemic brought to light the very real possibility of pathogens changing and shaping the way we live, and our lack of preparedness to deal with viral/bacterial outbreaks. Importantly, the quick detection of pathogens can help prevent and control the spread of disease, making the importance of diagnostic techniques undeniable. Point-of-care diagnostics started as a supplement to standard lab-based diagnostics, and are gradually becoming mainstream. Because of this, and their importance in detecting pathogens (especially in the developing world), their development has accelerated at an unprecedented rate. In this review, we highlight some important and recent examples of point-of-care diagnostics for detecting nucleic acids, proteins, bacteria, and other biomarkers, with the intent of making apparent their positive impact on society and human health.

Ion-Induced Phase Transfer of Cationic Dyes for Fluorescence-Based Electrolyte Sensing in Droplet Microfluidics

Fluorescence-based sensing in droplet microfluidics requires small sample volumes, allows for high-throughput assays, and does not suffer from photobleaching as each flowing sensor is only scanned one time. In this paper, we report a selective and sensitive fluorescence-based ion-sensing methodology in droplet microfluidics using a T-junction PDMS chip. The oil stream is doped with sensor ingredients including an ionophore, a cation exchanger, and a permanently cationic fluorophore as the optical reporter. Electrolyte cations from the aqueous sample are extracted into oil segments and displace the cationic dyes into aqueous droplets. Laser-induced fluorescence of the two immiscible phases is collected alternately, which is in clear contrast to most other ion-selective optode configurations such as nanoparticle suspensions that rely on mixed optical signals of two phases. The cation exchanger, tetrakis[3,5-bis(trifluoromethyl)phenyl]borate, is found to dramatically enhance the dye emission in the nonpolar sensing oil by preventing ion-pairing interactions and aggregations of the dye molecules, providing new insights into the mechanism of cationic dye-based ion sensors. The high dye brightness allows us to use low concentrations of sensing chemicals (e.g., 10 μM) in the oil and attain high sensitivity for detection of ions in an equal volume of sample. Using valinomycin as the ionophore and methylene blue as the dye, K⁺ is detected with a response time of ∼11 s, a logarithmic linear range of 10^-5 to 10^-2 M, a 20-fold total fluorescence response, >1000-fold selectivity against other electrolyte cations, and negligible cross-sensitivity toward the sample pH. The K⁺ concentration in untreated and undiluted whole blood and sweat samples is successfully determined by this microfluidic sensing method without optical interference from the droplet sample to the sensing oil. Detection of other ionic analytes can be achieved using the corresponding ionophores.

Integration of organic and inorganic photothermal probes for enhanced photothermometric sensing of silver ions

A new signal-amplified photothermometric sensor of Ag⁺ was explored based on a simple yet effective integration of inorganic and organic photothermal probes, mainly depending on the successful exploitation of a dual-signal transduction channel originating from the inherent photothermal property and the peroxidase-like activity of Prussian blue nanocubes (PB NCs).

Hydrogel-Based Optical Ion Sensors: Principles and Challenges for Point-of-Care Testing and Environmental Monitoring

Hydrogel is a unique family of biocompatible materials with growing applications in chemical and biological sensors. During the past few decades, various hydrogel-based optical ion sensors have been developed aiming at point-of-care testing and environmental monitoring. In this Perspective, we provide an overview of the research field including topics such as photonic crystals, DNAzyme cross-linked hydrogels, ionophore-based ion sensing hydrogels, and fluoroionophore-based optodes. As the different sensing principles are summarized, each strategy offers its advantages and limitations. In a nutshell, developing optical ion sensing hydrogels is still in the early stage with many opportunities lying ahead, especially with challenges in selectivity, assay time, detection limit, and usability.

Hydrogel-Based Stamping Technology for Solution-Free Blood Cell Staining

An accurate microscopical analysis of blood smears requires a reproducible and convenient method of staining. Solution-based staining procedures can be cumbersome. Especially in low- and middle-income countries, the lack of skilled technicians and adequate laboratory facilities, as well as insufficient water and reagent quality, often become confounding factors. To overcome these obstacles, we developed a new cell staining method based on sequential stamping of agarose gel patches that contain eosin, methylene blue/oxidized methylene blue, Azure B, and buffer, respectively. Our method, termed "hydrogel staining", provides a simple, reproducible, solution-free, and inexpensive approach to stain blood cells. We have optimized incubation times to achieve the optimal transfer of dyes to fixed blood cells on a glass slide, with outcomes comparable to conventional solution-based methods for white blood cells and malaria-infected red blood cells. This hydrogel staining method does not require special skills to produce excellent quality stained blood film slides. The new method could enhance the accuracy of microscopical examination of blood smears, especially in resource-limited settings.

Colorimetric ratiometry with ion optodes for spatially resolved concentration analysis

The deprotonation degree of the lipophilic pH indicator dye (chromoionophore) in ionophore-based ion optodes (so-called bulk optodes) has traditionally been measured spectrophotometrically. This makes it difficult to obtain spatially resolved concentration information, for example in the study of heterogenous systems. This article reports on a new colorimetric method that relies on a ratiometric image analysis. The acquision of image data allows one to map the deprotonation degree in two dimensions, which in turn is used to obtain the spatially-resolved ion concentration of the image. Using the detection of potassium as an example, the deprotonation degree data calculated on the basis of image analysis correlate quantitatively with those from spectrophotometry. They showed no dependence on the type of camera used in spite of their different gamma correction values and spectral sensitivities, as expected from theory. As an example, the method is successfully applied to the pixel level analysis of an ensemble of pictures acquired at different times to spatially and temporally observe potassium ion diffusion into an agarose gel containing a potassium-selective optical sensor microemulsion.

Ionophore-Based Ion-Selective Nanospheres Based on Monomer-Dimer Conversion in the Near-Infrared Region

Here, we report ion-selective nanospheres with readout in the near-infrared (NIR) region in both fluorescence and absorbance modes. The nanospheres rely on an ionophore-mediated monomer-dimer conversion of an NIR transducer, DTTC. The DTTC monomer in the nanospheres emits fluorescence around 820 nm, while the dimer in the aqueous environment generates strong blue-shifted emission around 660 nm. With a lead ionophore, an unprecedented lower detection limit of 3 pM for Pb²⁺ was achieved, allowing us to determine Pb²⁺ levels in river water without diluting the sample. Also, the Cu²⁺-selective nanospheres showed a detection limit of 5 nM. Taking advantage of the biologically desired NIR window, blood potassium concentrations were also determined without a complicated sample pretreatment. The sensing process was explained with a theoretical model. The detection range was found finely adjustable by the amount of nanospheres used. Therefore, the nanospheres formed a highly selective, sensitive, versatile, and rapid analytical platform for metal-ion sensing.

Novel phthalocyanine-based micelles/PNIPAM composite hydrogels: spatially/temporally controlled drug release triggered by NIR laser irradiation

Near-infrared (NIR) light-responsive hydrogels hold significant potential for biomedical application, especially in the remote-controlled release of anticancer drugs.

Molecularly-ordered hydrogels with controllable, anisotropic stimulus response

Hydrogels which morph between programmed shapes in response to aqueous stimuli are of significant interest for biosensors and artificial muscles, among other applications. However, programming hydrogel shape change at small size scales is a significant challenge. Here we use the inherent ordering capabilities of liquid crystals to create a mechanically anisotropic hydrogel; when coupled with responsive comonomers, the mechanical anisotropy in the network guides shape change in response to the desired aqueous condition. Our synthetic strategy hinges on the use of a methacrylic chromonic liquid crystal monomer which can be combined with a non-polymerizable chromonic of similar structure to vary the magnitude of shape change while retaining liquid crystalline order. This shape change is directional due to the mechanical anisotropy of the gel, which is up to 50% stiffer along the chromonic stack direction than perpendicular. Additionally, we show that the type of stimulus to which these anisotropic gels respond can be switched by incorporating responsive, hydrophilic comonomers without destroying the nematic phase or alignment. The utility of these properties is demonstrated in polymerized microstructures which exhibit Gaussian curvature in response to high pH due to emergent ordering in a micron-sized capillary.

Distance and Color Change Based Hydrogel Sensor for Visual Quantitative Determination of Buffer Concentrations

We present here an innovative platform for the determination of pH buffer capacity based on FITC-dextran loaded hydrogels. Optical signals from the pH-sensitive hydrogels were analyzed by simple parameters including distance and color change. The methodology was validated on five different buffer systems and exhibited wide linearity (0.1 to 100 mM), good batch-to-batch reproducibility, high versatility, and resistance to background ionic strength changes. Experimental results also fit well with a theoretical model based on numerical simulation. Preliminary application in carbonate alkalinity determination of seawater proved very successful. This hydrogel buffer concentration sensor is fundamentally different from conventional acid-base titrations, brings minimum perturbation to samples, and shows great potential in real applications.

Rhodamine dye transfer from hydrogel to nanospheres for the chemical detection of potassium ions

Smart hydrogels incorporating various functional nanomaterials are becoming popular tools for chemical sensing.