Oxygen-Tolerant ATRP Depolymerization Enabled by an External Radical Source

Although the chemical recycling of polymers synthesized by controlled radical polymerization enables the recovery of pristine monomer at low temperatures, it operates efficiently under strictly anaerobic conditions. Instead, oxygen-tolerant depolymerizations are scarce, and are either restricted to the use of a boiling co-solvent or are performed in closed vessels, often suffering from low conversions. Here, an open-vessel, oxygen-tolerant depolymerization of atom transfer radical polymerization (ATRP)-synthesized polymers is introduced, leading to high percentages of monomer regeneration (>90% depolymerization efficiency). Dissolved oxygen is eliminated by either utilizing high catalyst loadings, or lower catalyst loadings combined with a radical initiator. Notably, the methodology is compatible with various solvents (i.e., anisole, 1,2,4-trichlorobenzene (TCB), 1,2-dichlorobenzene (DCB), etc.) and a range of commercially available ligands including tris 2-(dimethylamino)ethylamine (Me6TREN) and tris(2-pyridylmethyl)amine (TPMA), as well as more inexpensive alternatives such as tris(2-aminoethyl)amine (TREN) and N,N,N',N'',N''-pentamethyldiethylenetriamine (PMDETA).

Open-Air Chemical Recycling: Fully Oxygen-Tolerant ATRP Depolymerization

While oxygen-tolerant strategies have been overwhelmingly developed for controlled radical polymerizations, the low radical concentrations typically required for high monomer recovery render oxygen-tolerant solution depolymerizations particularly challenging. Here, an open-air atom transfer radical polymerization (ATRP) depolymerization is presented, whereby a small amount of a volatile cosolvent is introduced as a means to thoroughly remove oxygen. Ultrafast depolymerization (i.e., 2 min) could efficiently proceed in an open vessel, allowing a very high monomer retrieval to be achieved (i.e., ∼91% depolymerization efficiency), on par with that of the fully deoxygenated analogue. Oxygen probe studies combined with detailed depolymerization kinetics revealed the importance of the low-boiling point cosolvent in removing oxygen prior to the reaction, thus facilitating effective open-air depolymerization. The versatility of the methodology was demonstrated by performing reactions with a range of different ligands and at high polymer loadings (1 M monomer repeat unit concentration) without significantly compromising the yield. This approach provides a fully oxygen-tolerant, facile, and efficient route to chemically recycle ATRP-synthesized polymers, enabling exciting new applications.

Nucleic Acid-Binding Dyes as Versatile Photocatalysts for Atom-Transfer Radical Polymerization

Nucleic acid-binding dyes (NuABDs) are fluorogenic probes that light up after binding to nucleic acids. Taking advantage of their fluorogenicity, NuABDs have been widely utilized in the fields of nanotechnology and biotechnology for diagnostic and analytical applications. We demonstrate the potential of NuABDs together with an appropriate nucleic acid scaffold as an intriguing photocatalyst for precisely controlled atom-transfer radical polymerization (ATRP). Additionally, we systematically investigated the thermodynamic and electrochemical properties of the dyes, providing insights into the mechanism that drives the photopolymerization. The versatility of the NuABD-based platform was also demonstrated through successful polymerizations using several NuABDs in conjunction with diverse nucleic acid scaffolds, such as G-quadruplex DNA or DNA nanoflowers. This study not only extends the horizons of controlled photopolymerization but also broadens opportunities for nucleic acid-based materials and technologies, including nucleic acid-polymer biohybrids and stimuli-responsive ATRP platforms.

Temporal Regulation of PET-RAFT Controlled Radical Depolymerization

A photocatalytic RAFT-controlled radical depolymerization method is introduced for precisely conferring temporal control under visible light irradiation. By regulating the deactivation of the depropagating chains and suppressing thermal initiation, an excellent temporal control was enabled, exemplified by several consecutive "on" and "off" cycles. Minimal, if any, depolymerization could be observed during the dark periods while the polymer chain-ends could be efficiently re-activated and continue to depropagate upon re-exposure to light. Notably, favoring deactivation resulted in the gradual unzipping of polymer chains and a stepwise decrease in molecular weight over time. This synthetic approach constitutes a simple methodology to modulate temporal control during the chemical recycling of RAFT-synthesized polymers while offering invaluable mechanistic insights.

Photocatalytic ATRP Depolymerization: Temporal Control at Low ppm of Catalyst Concentration

A photocatalytic ATRP depolymerization is introduced that significantly suppresses the reaction temperature from 170 to 100 °C while enabling temporal regulation. In the presence of low-toxicity iron-based catalysts and under visible light irradiation, near-quantitative monomer recovery could be achieved (up to 90%), albeit with minimal temporal control. By employing ppm concentrations of either FeCl2 or FeCl3, the depolymerization during the dark periods could be completely eliminated, thus enabling temporal control and the possibility to modulate the rate by simply turning the light "on" and "off". Notably, our approach allowed preservation of the end-group fidelity throughout the reaction, could be carried out at high polymer loadings (up to 2M), and was compatible with various polymers and light sources. This methodology provides a facile, environmentally friendly, and temporally regulated route to chemically recycle ATRP-synthesized polymers, thus opening the door for further opportunities.

Synthesis of Multifunctional Protein-Polymer Conjugates via Oxygen-tolerant, Aqueous Copper-Mediated Polymerization, and Bioorthogonal Click Chemistry

Oxygen-tolerant, aqueous copper-mediated polymerization approaches are combined with click chemistry in either a sequential or a simultaneous manner, to enable the synthesis of multifunctional protein-polymer conjugates. Propargyl acrylate (PgA) and propargyl methacrylate (PgMA) grafting from a bovine serum albumin (BSA) macroinitiator is thoroughly optimized to synthesize chemically addressable BSA-poly(propargyl acrylate) and BSA-poly(propargyl methacrylate) respectively. The produced multifunctional bioconjugates bear pendant terminal 1-alkynes which can be readily post-functionalized via both [3+2] Huisgen cycloaddition and thiol-yne click chemistry under mild reaction conditions. Simultaneous oxygen-tolerant, aqueous copper-catalyzed polymerization, and click chemistry mediate the in situ multiple chemical tailoring of biomacromolecules in excellent yields.

Comparison of Mechano- and PhotoATRP with ZnO Nanocrystals

Zinc oxide (ZnO) was previously reported as an excellent cocatalyst for mechanically controlled atom transfer radical polymerization (mechanoATRP), but its photocatalytic properties in photoinduced ATRP (photoATRP) have been much less explored. Herein, well-defined ZnO nanocrystals were prepared via microwave-assisted synthesis and applied as a heterogeneous cocatalyst in mechano- and photoATRP. Both techniques yielded polymers with outstanding control over the molecular weight, but ZnO-cocatalyzed photoATRP was much faster than analogous mechanoATRP (conversion of 91% in 1 h vs 54% in 5 h). The kinetics of photoATRP was tuned by loadings of ZnO nanocrystals. PhotoATRP with ZnO did not require any excess of ligand versus Cu, in contrast to mechanoATRP, requiring an excess of ligand, acting as a reducing agent. ZnO-cocatalyzed photoATRP proceeded controllably without prior deoxygenation, since ZnO was involved in a cascade of reactions, leading to the rapid elimination of oxygen. The versatility and robustness of the technique were demonstrated for various (meth)acrylate monomers with good temporal control and preservation of end-group functionality, illustrated by the formation of tailored block copolymers.

Fully Oxygen-Tolerant Visible-Light-Induced ATRP of Acrylates in Water: Toward Synthesis of Protein-Polymer Hybrids

Over the last decade, photoinduced ATRP techniques have been developed to harness the energy of light to generate radicals. Most of these methods require the use of UV light to initiate polymerization. However, UV light has several disadvantages: it can degrade proteins, damage DNA, cause undesirable side reactions, and has low penetration depth in reaction media. Recently, we demonstrated green-light-induced ATRP with dual catalysis, where eosin Y (EYH2) was used as an organic photoredox catalyst in conjunction with a copper complex. This dual catalysis proved to be highly efficient, allowing rapid and well-controlled aqueous polymerization of oligo(ethylene oxide) methyl ether methacrylate without the need for deoxygenation. Herein, we expanded this system to synthesize polyacrylates under biologically relevant conditions using CuII/Me6TREN (Me6TREN = tris[2-(dimethylamino)ethyl]amine) and EYH2 at ppm levels. Water-soluble oligo(ethylene oxide) methyl ether acrylate (average M n = 480, OEOA480) was polymerized in open reaction vessels under green light irradiation (520 nm). Despite continuous oxygen diffusion, high monomer conversions were achieved within 40 min, yielding polymers with narrow molecular weight distributions (1.17 ≤ D̵ ≤ 1.23) for a wide targeted DP range (50-800). In situ chain extension and block copolymerization confirmed the preserved chain end functionality. In addition, polymerization was triggered/halted by turning on/off a green light, showing temporal control. The optimized conditions also enabled controlled polymerization of various hydrophilic acrylate monomers, such as 2-hydroxyethyl acrylate, 2-(methylsulfinyl)ethyl acrylate), and zwitterionic carboxy betaine acrylate. Notably, the method allowed the synthesis of well-defined acrylate-based protein-polymer hybrids using a straightforward reaction setup without rigorous deoxygenation.

Open-air green-light-driven ATRP enabled by dual photoredox/copper catalysis

Photoinduced atom transfer radical polymerization (photo-ATRP) has risen to the forefront of modern polymer chemistry as a powerful tool giving access to well-defined materials with complex architecture. However, most photo-ATRP systems can only generate radicals under biocidal UV light and are oxygen-sensitive, hindering their practical use in the synthesis of polymer biohybrids. Herein, inspired by the photoinduced electron transfer-reversible addition-fragmentation chain transfer (PET-RAFT) polymerization, we demonstrate a dual photoredox/copper catalysis that allows open-air ATRP under green light irradiation. Eosin Y was used as an organic photoredox catalyst (PC) in combination with a copper complex (X-CuII/L). The role of PC was to trigger and drive the polymerization, while X-CuII/L acted as a deactivator, providing a well-controlled polymerization. The excited PC was oxidatively quenched by X-CuII/L, generating CuI/L activator and PC˙+. The ATRP ligand (L) used in excess then reduced the PC˙+, closing the photocatalytic cycle. The continuous reduction of X-CuII/L back to CuI/L by excited PC provided high oxygen tolerance. As a result, a well-controlled and rapid ATRP could proceed even in an open vessel despite continuous oxygen diffusion. This method allowed the synthesis of polymers with narrow molecular weight distributions and controlled molecular weights using Cu catalyst and PC at ppm levels in both aqueous and organic media. A detailed comparison of photo-ATRP with PET-RAFT polymerization revealed the superiority of dual photoredox/copper catalysis under biologically relevant conditions. The kinetic studies and fluorescence measurements indicated that in the absence of the X-CuII/L complex, green light irradiation caused faster photobleaching of eosin Y, leading to inhibition of PET-RAFT polymerization. Importantly, PET-RAFT polymerizations showed significantly higher dispersity values (1.14 ≤ Đ ≤ 4.01) in contrast to photo-ATRP (1.15 ≤ Đ ≤ 1.22) under identical conditions.

Rapid Oxygen-Tolerant Synthesis of Protein-Polymer Bioconjugates via Aqueous Copper-Mediated Polymerization

The synthesis of protein-polymer conjugates usually requires extensive and costly deoxygenation procedures, thus limiting their availability and potential applications. In this work, we report the ultrafast synthesis of polymer-protein bioconjugates in the absence of any external deoxygenation via an aqueous copper-mediated methodology. Within 10 min and in the absence of any external stimulus such as light (which may limit the monomer scope and/or disrupt the secondary structure of the protein), a range of hydrophobic and hydrophilic monomers could be successfully grafted from a BSA macroinitiator, yielding well-defined polymer-protein bioconjugates at quantitative yields. Our approach is compatible with a wide range of monomer classes such as (meth) acrylates, styrene, and acrylamides as well as multiple macroinitiators including BSA, BSA nanoparticles, and beta-galactosidase from Aspergillus oryzae. Notably, the synthesis of challenging protein-polymer-polymer triblock copolymers was also demonstrated, thus significantly expanding the scope of our strategy. Importantly, both lower and higher scale polymerizations (from 0.2 to 35 mL) were possible without compromising the overall efficiency and the final yields. This simple methodology paves the way for a plethora of applications in aqueous solutions without the need of external stimuli or tedious deoxygenation.

Atom Transfer Radical Polymerization: A Mechanistic Perspective

Since its inception, atom transfer radical polymerization (ATRP) has seen continuous evolution in terms of the design of the catalyst and reaction conditions; today, it is one of the most useful techniques to prepare well-defined polymers as well as one of the most notable examples of catalysis in polymer chemistry. This Perspective highlights fundamental advances in the design of ATRP reactions and catalysts, focusing on the crucial role that mechanistic studies play in understanding, rationalizing, and predicting polymerization outcomes. A critical summary of traditional ATRP systems is provided first; we then focus on the most recent developments to improve catalyst selectivity, control polymerizations via external stimuli, and employ new photochemical or dual catalytic systems with an outlook to future research directions and open challenges.

Photoinduced Controlled/Living Polymerizations

The application of photochemistry in polymer synthesis is of interest due to the unique possibilities offered compared to thermochemistry, including topological and temporal control, rapid polymerization, sustainable low-energy processes, and environmentally benign features leading to established and emerging applications in adhesives, coatings, adaptive manufacturing, etc. In particular, the utilization of photochemistry in controlled/living polymerizations often offers the capability for precise control over the macromolecular structure and chain length in addition to the associated advantages of photochemistry. Herein, the latest developments in photocontrolled living radical and cationic polymerizations and their combinations for application in polymer syntheses are discussed. This Review summarizes and highlights recent studies in the emerging area of photoinduced controlled/living polymerizations. A discussion of mechanistic details highlights differences as well as parallels between different systems for different polymerization methods and monomer applicability.

Ultrafast Visible-Light-Induced ATRP in Aqueous Media with Carbon Quantum Dots as the Catalyst and Its Application for 3D Printing

Photoinduced atom transfer radical polymerization (ATRP) has been proved to be a versatile technique for polymer network formation. However, the slow polymerization rates of typical ATRP limited its application in the field of additive manufacturing (3D printing). In this work, we introduced carbon quantum dots (CQDs) for the first time to the ATRP in aqueous media and developed an ultrafast visible-light-induced polymerization system. After optimization, the polymerization could achieve a high monomer conversion (>90%) within 1 min, and the polydispersity index (PDI) of the polymer was lower than 1.25. This system was then applied as the first example of ATRP for the 3D printing of hydrogel through digital light processing (DLP), and the printed object exhibited good dimensional accuracy. Additionally, the excellent and stable optical properties of CQDs also provided interesting photoluminescence capabilities to the printed objects. We deduce this ATRP mediated 3D printing process would provide a new platform for the preparation of functional and stimuli-responsive hydrogel materials.

Oxygen Tolerance in Surface-Initiated Reversible Deactivation Radical Polymerizations: Are Polymer Brushes Turning into Technology?

Over the past three decades, the development of reversible deactivation radical polymerizations (RDRP), and advancements toward more user-friendly and accessible experimental setups have opened the door for nonexperts to design complex macromolecules with well-defined properties. External mediation, improved tolerance to oxygen, and increased reaction volumes for higher synthetic output are some of the many noteworthy technical improvements. The development of RDRPs in solution was paralleled by their application on solid substrates to synthesize surface-grafted "polymer brushes" via surface-initiated RDRP (SI-RDRP). This Viewpoint paper provides a current perspective on recent developments in SI-RDRP methods that are tolerant to oxygen, especially highlighting those that could potentially enable scaling up of the synthesis of brushes for the functionalization of technologically relevant materials.

Red-Light-Induced, Copper-Catalyzed Atom Transfer Radical Polymerization

Despite advances in photochemical atom transfer radical polymerization (photoATRP), these systems often rely on the use of UV light for the activation/generation of the copper-based catalytic species. To circumvent the problems associated with the UV light, we developed a dual photoredox catalytic system to mediate photoinduced ATRP under red-light irradiation. The catalytic system is comprised of a Cu catalyst to control the polymerization via ATRP equilibrium and a photocatalyst, such as zinc(II) tetraphenylporphine or zinc(II) phthalocyanine, to generate the activator Cu^I species under red-light irradiation. In addition, this system showed oxygen tolerance due to the consumption of oxygen in the photoredox reactions, yielding well-controlled polymerizations without the need for deoxygenation processes.

Wavelength-Resolved PhotoATRP

The careful mapping of photoinduced reversible-deactivation radical polymerizations (RDRP) is a prerequisite for their applications in soft matter materials design. Here, we probe the wavelength-dependent behavior of photochemically induced atom transfer radical polymerization (ATRP) using nanosecond pulsed-laser polymerization (PLP). The photochemical reactivities at identical photon fluxes of methyl acrylate in terms of conversion, number-average molecular weight, and dispersity of the resulting polymers are mapped against the absorption spectrum of the copper(II) catalyst in the range of 305-550 nm. We observe a red shift of the action spectrum relative to the absorption spectrum of the copper(II) catalyst. Both the number-average molecular weight and the dispersity show a wavelength dependence, while the molecular weight and conversion remain linearly correlated. The reported data allow the judicious selection of optimum wavelengths for photoATRP.

Functional pH-responsive polymers containing dynamic enaminone linkages for the release of active organic amines

Dynamic covalent bonds have attracted attention for the development of pH-responsive polymers, however, studies using acid-cleavable enaminone linkages as a means of controlled drug release have been limited. Herein, we...

Fluorescence enables high throughput screening of polyelectrolyte–protein binding affinities

Förster resonance energy transfer (FRET) in combination with high throughput controlled radical polymerisation allows quick identification of polymers that can bind strongly to enzymes such as glucose oxidase.

Shape-Controlled Nanoparticles from a Low-Energy Nanoemulsion

Nanoemulsion technology enables the production of uniform nanoparticles for a wide range of applications. However, existing nanoemulsion strategies are limited to the production of spherical nanoparticles. Here, we describe a low-energy nanoemulsion method to produce nanoparticles with various morphologies. By selecting a macro-RAFT agent (poly(di(ethylene glycol) ethyl ether methacrylate-co-N-(2-hydroxypropyl) methacrylamide) (P(DEGMA-co-HPMA))) that dramatically lowers the interfacial tension between monomer droplets and water, we can easily produce nanoemulsions at room temperature by manual shaking for a few seconds. With the addition of a common ionic surfactant (SDS), these nanoscale droplets are robustly stabilized at both the formation and elevated temperatures. Upon polymerization, we produce well-defined block copolymers forming nanoparticles with a wide range of controlled morphologies, including spheres, worm balls, worms, and vesicles. Our nanoemulsion polymerization is robust and well-controlled even without stirring or external deoxygenation. This method significantly expands the toolbox and availability of nanoemulsions and their tailor-made polymeric nanomaterials.

Making ATRP More Practical: Oxygen Tolerance

Atom-transfer radical polymerization (ATRP) is a well-known technique for the controlled polymerization of vinyl monomers under mild conditions. However, as with any other radical polymerization, ATRP typically requires rigorous oxygen exclusion, making it time-consuming and challenging to use by nonexperts. In this Account, we discuss various approaches to achieving oxygen tolerance in ATRP, presenting the overall progress in the field.Copper-mediated ATRP, which we first discovered in the late 1990s, uses a Cu^I/L activator that reversibly reacts with the dormant C(sp³)-X polymer chain end, forming a X-Cu^II/L deactivator and a propagating radical. Oxygen interferes with activation and chain propagation by quenching the radicals and oxidizing the activator. At ATRP equilibrium, the activator is present at a much higher concentration than the propagating radicals. Thus, oxidation of the activator is the dominant inhibition pathway. In conventional ATRP, this reaction is irreversible, so oxygen must be strictly excluded to achieve good results.Over the last two decades, our group has developed several ATRP techniques based on the concept of regenerating the activator. When the oxidized activator is continuously converted back to its active reduced form, then the catalytic system itself can act as an oxygen scavenger. Regeneration can be accomplished by reducing agents and photo-, electro-, and mechanochemical stimuli. This family of methods offers a degree of oxygen tolerance, but most of them can tolerate only a limited amount of oxygen and do not allow polymerization in an open vessel.More recently, we discovered that enzymes can be used in auxiliary catalytic systems that directly deoxygenate the reaction medium and protect the polymerization process. We developed a method that uses glucose oxidase (GOx), glucose, and sodium pyruvate to very effectively scavenge oxygen and enable open-vessel ATRP. By adding a second enzyme, horseradish peroxidase (HPR), we managed to extend the role of the auxiliary enzymatic system to generating carbon-based radicals and changed ATRP from an oxygen-sensitive to an oxygen-fueled reaction.While performing control experiments for the enzymatic methods, we noticed that using sodium pyruvate under UV irradiation triggers polymerization without the presence of GOx. This serendipitous discovery allowed us to develop the first oxygen-proof, small-molecule-based, photoinduced ATRP system. It has oxygen tolerance similar to that of the enzymatic methods, exhibits superior compatibility with both aqueous media and organic solvents, and avoids problems associated with purifying polymers from enzymes. The system was able to rapidly polymerize N-isopropylacrylamide, a challenging monomer, with a high degree of control.These contributions have substantially simplified the use of ATRP, making it more practical and accessible to everyone.

Oxygen tolerant, photoinduced controlled radical polymerization approach for the synthesis of giant amphiphiles

New families of amphiphilic protein–polymer bioconjugates readily synthesized via an oxygen tolerant, photoinduced RDRP approach.

How does the single unit monomer insertion technique promote kinetic analysis of activation and initiation in photo-RAFT processes?

The single unit monomer insertion technique provides a simple platform for the kinetic investigation of early stage of photo-RAFT process that comprises photo-activation of initial RAFT agents and addition of RAFT leaving radicals to the monomers.

A Schiff base ligand for photoinduced atom transfer radical polymerization

A claw-type Schiff base, tris[N-(2-pyridylmethyl)-2-iminoethyl]amine (Py₃Tren), is used as an active ligand for photoinduced atom transfer radical polymerization (Photo-ATRP).

Fully oxygen-tolerant atom transfer radical polymerization triggered by sodium pyruvate

ATRP (atom transfer radical polymerization) is one of the most robust reversible deactivation radical polymerization (RDRP) systems. However, the limited oxygen tolerance of conventional ATRP impedes its practical use in an ambient atmosphere. In this work, we developed a fully oxygen-tolerant PICAR (photoinduced initiators for continuous activator regeneration) ATRP process occurring in both water and organic solvents in an open reaction vessel. Continuous regeneration of the oxidized form of the copper catalyst with sodium pyruvate through UV excitation allowed the chemical removal of oxygen from the reaction mixture while maintaining a well-controlled polymerization of N-isopropylacrylamide (NIPAM) or methyl acrylate (MA) monomers. The polymerizations of NIPAM were conducted with 250 ppm (with respect to the monomer) or lower concentrations of CuBr2 and a tris[2-(dimethylamino)ethyl]amine ligand. The polymers were synthesized to nearly quantitative monomer conversions (>99%), high molecular weights (M n > 270 000), and low dispersities (1.16 < Đ < 1.44) in less than 30 min under biologically relevant conditions. The reported method provided a well-controlled ATRP (Đ = 1.16) of MA in dimethyl sulfoxide despite oxygen diffusion from the atmosphere into the reaction system.

Automatic peak assignment and visualisation of copolymer mass spectrometry data using the 'genetic algorithm'

Copolymer analysis is vitally important as the materials have a wide variety of applications due to their tunable properties. Processing mass spectrometry data for copolymer samples can be very complex due to the increase in the number of species when the polymer chains are formed by two or more monomeric units. In this paper, we describe the use of the genetic algorithm for automated peak assignment of copolymers synthesised by a variety of polymerisation methods. We find that in using this method we are able to easily assign copolymer spectra in a few minutes and visualise them into heat maps. These heat maps allow us to look qualitatively at the distribution of the chains, by showing how they alter with different polymerisation techniques, and by changing the initial copolymer composition. This methodology is simple to use and requires little user input, which makes it well suited for use by less expert users. The data outputted by the automatic assignment may also allow for more complex data processing in the future.

Enlightening advances in polymer bioconjugate chemistry: light-based techniques for grafting to and from biomacromolecules

Photochemistry has revolutionized the field of polymer-biomacromolecule conjugation. Ligation reactions necessitate biologically benign conditions, and photons have a significant energy advantage over what is available thermally at ambient temperature, allowing for rapid and unique reactivity. Photochemical reactions also afford many degrees of control, specifically, spatio-temporal control, light source tunability, and increased oxygen tolerance. Light-initiated polymerizations, in particular photo-atom-transfer radical polymerization (photo-ATRP) and photoinduced electron/energy transfer reversible addition-fragmentation chain transfer polymerization (PET-RAFT), have been used for grafting from proteins, DNA, and cells. Additionally, the spatio-temporal control inherent to light-mediated chemistry has been utilized for grafting biomolecules to hydrogel networks for many applications, such as 3-D cell culture. While photopolymerization has clear advantages, there are factors that require careful consideration in order to obtain optimal control. These factors include the photocatalyst system, light intensity, and wavelength. This Perspective aims to discuss recent advances of photochemistry for polymer biomacromolecule conjugation and potential considerations while tailoring these systems.

Rapidly self-deoxygenating controlled radical polymerization in water via in situ disproportionation of Cu(i)

Rapidly self-deoxygenating Cu-RDRP in aqueous media is investigated. The disproportionation of Cu(i)/Me6Tren in water towards Cu(ii) and highly reactive Cu(0) leads to O2-free reaction environments within the first seconds of the reaction, even when the reaction takes place in the open-air. By leveraging this significantly fast O2-reducing activity of the disproportionation reaction, a range of well-defined water-soluble polymers with narrow dispersity are attained in a few minutes or less. This methodology provides the ability to prepare block copolymers via sequential monomer addition with little evidence for chain termination over the lifetime of the polymerization and allows for the synthesis of star-shaped polymers with the use of multi-functional initiators. The mechanism of self-deoxygenation is elucidated with the use of various characterization tools, and the species that participate in the rapid oxygen consumption is identified and discussed in detail.

Protein-polymer bioconjugates via a versatile oxygen tolerant photoinduced controlled radical polymerization approach

The immense application potential of amphiphilic protein-polymer conjugates remains largely unexplored, as established "grafting from" synthetic protocols involve time-consuming, harsh and disruptive deoxygenation methods, while "grafting to" approaches result in low yields. Here we report an oxygen tolerant, photoinduced CRP approach which readily affords quantitative yields of protein-polymer conjugates within 2 h, avoiding damage to the secondary structure of the protein and providing easily accessible means to produce biomacromolecular assemblies. Importantly, our methodology is compatible with multiple proteins (e.g. BSA, HSA, GOx, beta-galactosidase) and monomer classes including acrylates, methacrylates, styrenics and acrylamides. The polymerizations are conveniently conducted in plastic syringes and in the absence of any additives or external deoxygenation procedures using low-organic content media and ppm levels of copper. The robustness of the protocol is further exemplified by its implementation under UV, blue light or even sunlight irradiation as well as in buffer, nanopure, tap or even sea water.

Mass spectrometry as a tool to advance polymer science

In contrast to natural polymers, which have existed for billions of years, the first well-understood synthetic polymers date back to just over one century ago. Nevertheless, this relatively short period has seen vast progress in synthetic polymer chemistry, which can now afford diverse macromolecules with varying structural complexities. To keep pace with this synthetic progress, there have been commensurate developments in analytical chemistry, where mass spectrometry has emerged as the pre-eminent technique for polymer analysis. This Perspective describes present challenges associated with the mass-spectrometric analysis of synthetic polymers, in particular the desorption, ionization and structural interrogation of high-molar-mass macromolecules, as well as strategies to lower spectral complexity. We critically evaluate recent advances in technology in the context of these challenges and suggest how to push the field beyond its current limitations. In this context, the increasingly important role of high-resolution mass spectrometry is emphasized because of its unrivalled ability to describe unique species within polymer ensembles, rather than to report the average properties of the ensemble.

Aqueous copper-mediated reversible deactivation radical polymerization (RDRP) utilizing polyetheramine derived initiators

Polyetheramines (Jeffamines™) are used in Copper-mediated reversible deactivation radical polymeriation (Cu-RDRP) in water for the synthesis of temperature-responsive block copolymers.

Iodine-mediated photoATRP in aqueous media with oxygen tolerance

Iodine-mediated photoATRP was conducted in aqueous media enabling fast and well-controlled polymerizations under visible light without deoxygenation.

PCR-RAFT: rapid high throughput oxygen tolerant RAFT polymer synthesis in a biology laboratory

We performed high-throughput oxygen tolerant ultra-fast RAFT polymerisation producing complex polymer libraries utilising PCR thermocyclers. This now enables the preparation of these libraries in under 5 min without chemistry equipment.

Effect of Polymerization Components on Oxygen-Tolerant Photo-ATRP

Photo-ATRP has recently emerged as a powerful technique that allows for oxygen-tolerant polymerizations and the preparation of polymers with low dispersity and high end-group fidelity. However, the effect of various photo-ATRP components on oxygen consumption and polymerization remains elusive. Herein, we employ an in situ oxygen probe and UV-vis spectroscopy to elucidate the effects of ligand, initiator, monomer, and solvent on oxygen consumption. We found that the choice of photo-ATRP components significantly impacts the rate at which the oxygen is consumed and can subsequently affect both the polymerization time and the dispersity of the resulting polymer. Importantly, we discovered that using the inexpensive ligand TREN results in the fastest oxygen consumption and shortest polymerization time, even though no appreciable reduction of CuBr₂ is observed. This work provides insight into oxygen consumption in photo-ATRP and serves as a guideline to the judicious selection of photo-ATRP components for the preparation of well-defined polymers.

Tailoring polymer dispersity and shape of molecular weight distributions: methods and applications

The width and shape of molecular weight distributions can significantly affect the properties of polymeric materials and thus are key parameters to control. This mini-review aims to critically summarise recent approaches developed to tailor molecular weight distributions and highlights the strengths and limitations of each technique. Special emphasis will also be given to applications where tuning the molecular weight distribution has been used as a strategy to not only enhance polymer properties but also to increase the fundamental understanding behind complex mechanisms and phenomena.

An Oxygen Paradox: Catalytic Use of Oxygen in Radical Photopolymerization

A peculiar radical polymerization reaction is presented in which oxygen serves as a cocatalyst, alongside triethylamine, to provide activation with light in the far-red (690 nm, 3 mW cm^-2 ) of the PET-RAFT process in the presence of zinc(II) (2,3,7,8,12,13,17,18-octaethyl-5,10,15,20-tetraphenylporphyrin) as photocatalyst. Apart from the ability to exert temporal control by switching the light on or off, this system possesses the exciting capability of inducing temporal control by removal or reintroduction of oxygen. Furthermore, this multicomponent catalytic system was typified by controlled polymerizations of various acrylate and acrylamide monomers, which all resulted in well-defined polymers with low dispersity (<1.2). The process displayed excellent living characteristics that were demonstrated through chain extensions and a range of degrees of polymerization (200-1600).

Tuning Dispersity by Photoinduced Atom Transfer Radical Polymerisation: Monomodal Distributions with ppm Copper Concentration

Dispersity significantly affects the properties of polymers. However, current methods for controlling the polymer dispersity are limited to bimodal molecular weight distributions, adulterated polymer chains, or low end-group fidelity and rely on feeding reagents, flow-based, or multicomponent systems. To overcome these limitations, we report a simple batch system whereby photoinduced atom transfer radical polymerisation is exploited as a convenient and versatile technique to control dispersity of both homopolymers and block copolymers. By varying the concentration of the copper complex, a wide range of monomodal molecular weight distributions can be obtained (Đ=1.05-1.75). In all cases, high end-group fidelity was confirmed by MALDI-ToF-MS and exemplified by efficient block copolymer formation (monomodal, Đ=1.1-1.5). Importantly, our approach utilises ppm levels of copper (as low as 4 ppm), can be tolerant to oxygen and exhibits perfect temporal control, representing a major step forward in tuning polymer dispersity for various applications.

Bottom-up design of model network elastomers and hydrogels from precise star polymers

Well-defined high-molecular weight star polymers based on low-T_g water-soluble polymers enable bottom-up design of model network elastomers and functional hydrogels.

Microscale synthesis of multiblock copolymers using ultrafast RAFT polymerisation

We demonstrate that ultrafast RAFT in the presence of air can be scaled down to 2 μL with good control using microvolume insert vials as the polymerisation vessel.