Assembly with copper(ii) ions and D–π–A molecules on a graphene surface for ultra-fast acetic acid sensing at room temperature

Quartz Crystal Microbalance Coated with a Polyvinylpyrrolidone Microfiber Active Layer as a High-Performance Acetic Acid Gas Sensor

Acetic acid is among the most common and damaging airborne contaminants. Exposure to acetic acid gas can irritate the nose and throat, which may harm human health. In light of the increasing use of acetic acid in industry, there is a critical need for an acetic acid detection device that can operate in real time with excellent performance. This study developed an acetic acid gas sensor using a quartz crystal microbalance (QCM) deposited with polyvinylpyrrolidone (PVP) microfiber by a well-recognized electrospinning method. Scanning electron microscopy (SEM) and Fourier-transform infrared (FTIR) spectroscopy were employed to observe the morphology and chemical composition of the fabricated microfibers. The obtained sensor has a high sensitivity of (4.144 ± 0.039) Hz·ppm-1 with a low detection limit and rapid response and recovery times of 75 and 66 s, respectively. In addition, the fabricated sensor also exhibits good performance as well as repeatability and long-term stability. Selectivity tests were also conducted for various analytes and exhibited excellent selectivity toward acetic acid. These advancements demonstrate that the PVP microfiber active layers not only address the challenges of detection by enhancing sensitivity but also provide unique mechanism selectivity for acetic acid molecules. However, advanced future research must still be conducted to improve the sensor reversibility, making the sensor more suitable for applications in a real environment.

Recent Advances in Copper-Based Materials for Sustainable Environmental Applications

In recent years, copper-based nanomaterials have gained significant attention for their practical applications due to their cost-effectiveness, thermal stability, selectivity, high activity, and wide availability. This review focuses on the synthesis and extensive applications of copper nanomaterials in environmental catalysis, addressing knowledge gaps in pollution management. It highlights recent advancements in using copper-based nanomaterials for the remediation of heavy metals, organic pollutants, pharmaceuticals, and other contaminants. Also, it will be helpful to young researchers in improving the suitability of implementing copper-based nanomaterials correctly to establish and achieve sustainable goals for environmental remediation.

Highly Sensitive Sub-ppm CH3COOH Detection by Improved Assembly of Sn3O4-RGO Nanocomposite

Detection of sub-ppm acetic acid (CH₃COOH) is in demand for environmental gas monitoring. In this article, we propose a CH₃COOH gas sensor based on Sn₃O₄ and reduced graphene oxide (RGO), where the assembly of Sn₃O₄-RGO nanocomposites is dependent on the synthesis method. Three nanocomposites prepared by three different synthesis methods are investigated. The optimum assembly is by hydrothermal reactions of Sn⁴⁺ salts and pre-reduced RGO (designated as RS nanocomposite). Raman spectra verified the fingerprint of RGO in the synthesized RS nanocomposite. The Sn₃O₄ planes of (111), (210), (130), (13¯2) are observed from the X-ray diffractogram, and its average crystallite size is 3.94 nm. X-ray photoelectron spectroscopy on Sn3d and O1s spectra confirm the stoichiometry of Sn₃O₄ with Sn:O ratio = 0.76. Sn₃O₄-RGO-RS exhibits the highest response of 74% and 4% at 2 and 0.3 ppm, respectively. The sensitivity within sub-ppm CH₃COOH is 64%/ppm. Its superior sensing performance is owing to the embedded and uniformly wrapped Sn₃O₄ nanoparticles on RGO sheets. This allows a massive relative change in electron concentration at the Sn₃O₄-RGO heterojunction during the on/off exposure of CH₃COOH. Additionally, the operation is performed at room temperature, possesses good repeatability, and consumes only ~4 µW, and is a step closer to the development of a commercial CH₃COOH sensor.

Synthesis of Graphene-Based Nanocomposites for Environmental Remediation Applications: A Review

The term graphene was coined using the prefix "graph" taken from graphite and the suffix "-ene" for the C=C bond, by Boehm et al. in 1986. The synthesis of graphene can be done using various methods. The synthesized graphene was further oxidized to graphene oxide (GO) using different methods, to enhance its multitude of applications. Graphene oxide (GO) is the oxidized analogy of graphene, familiar as the only intermediate or precursor for obtaining the latter at a large scale. Graphene oxide has recently obtained enormous popularity in the energy, environment, sensor, and biomedical fields and has been handsomely exploited for water purification membranes. GO is a unique class of mechanically robust, ultrathin, high flux, high-selectivity, and fouling-resistant separation membranes that provide opportunities to advance water desalination technologies. The facile synthesis of GO membranes opens the doors for ideal next-generation membranes as cost-effective and sustainable alternative to long existing thin-film composite membranes for water purification applications. Many types of GO-metal oxide nanocomposites have been used to eradicate the problem of metal ions, halomethanes, other organic pollutants, and different colors from water bodies, making water fit for further use. Furthermore, to enhance the applications of GO/metal oxide nanocomposites, they were deposited on polymeric membranes for water purification due to their relatively low-cost, clear pore-forming mechanism and higher flexibility compared to inorganic membranes. Along with other applications, using these nanocomposites in the preparation of membranes not only resulted in excellent fouling resistance but also could be a possible solution to overcome the trade-off between water permeability and solute selectivity. Hence, a GO/metal oxide nanocomposite could improve overall performance, including antibacterial properties, strength, roughness, pore size, and the surface hydrophilicity of the membrane. In this review, we highlight the structure and synthesis of graphene, as well as graphene oxide, and its decoration with a polymeric membrane for further applications.

Charge transfer driven by redox dye molecules on graphene nanosheets for room-temperature gas sensing

Special functional groups to modify the surface of graphene have received much attention since they enable the charge transfer enhancement, thus realizing gas-sensing at room temperature. In this work, three typical redox dye molecules, methylene blue (MB), indigo carmine (IC) and anthraquinone-2-sulfonate (AQS), were selected to be supramolecularly assembled with reduced graphene oxide (rGO), respectively. Remarkably, three graphene-based materials AQS-rGO (response = 3.2, response time = 400 s), IC-rGO (response = 4.3, response time = 300 s) and MB-rGO (response = 7.1, response time = 100 s) exhibited excellent sensitivity and short response time toward 10 ppm NO₂ at room temperature. The corresponding NO₂ sensing mechanism of the obtained materials was further investigated by cyclic voltammetry (CV) measurements. CV was conducted to measure the anodic peak potential (E_pa) of three redox dyes. Interestingly, it is obvious that the E_pa values were positively correlated with the gas sensitivity and response time of the three materials. To explore the mechanism, UV-vis spectroscopy was adopted to analyze the lowest unoccupied molecular orbitals (LUMOs) of three redox dye molecules. The results show that the oxidation abilities of three redox dyes were also positively correlated with the gas sensitivity and response time of three corresponding graphene-based materials.

All-Dry Transferred ReS2 Nanosheets for Ultrasensitive Room-Temperature NO2 Sensing under Visible Light Illumination

For gas sensing applications, most of the reported two-dimensional (2D) materials are suffering from relatively low sensitivity and high limit of detection (LOD) at room temperature. In this work, we selected rhenium disulfide (ReS₂) nanosheets to fabricate ReS₂ transistor-based gas sensors (RTGSs) with ultrahigh sensitivity and low LOD toward nitrogen dioxide (NO₂). The ReS₂ nanosheets with different thicknesses were prepared via mechanical exfoliation and all-dry transfer method. Under 405 nm light illumination at room temperature (25 °C), the fabricated gas sensors showed a significant enhancement of the response with full reversibility toward ppb level NO₂ (response of 9.07 at 500 ppb, a LOD of 50 ppb). In particular, the total response and recovery time of the RTGS was revealed to be less than 4 minutes (55 and 180 s, respectively), which is one of the top three shortest response and recovery times toward ppb level NO₂ of the reported 2D material-based room-temperature gas sensors so far. Via Raman spectrometry, Kelvin probe force microscopy (KPFM), and X-ray photoelectron spectrometry (XPS), the structure and gas sensing mechanism of the materials were systematically investigated. It was confirmed that the electrons transfer from the ReS₂ surface to NO₂ molecules, inducing the hole doping of ReS₂, which consequently increased the sensor resistance. Moreover, the concentration of the photogenerated carriers in ReS₂ would accordingly be promoted by light illumination, which accounts for the substantial light enhancement of the gas sensing performance of RTGSs.