Structure formation and coarsening kinetics of phase-separated spin-coated ethylcellulose/hydroxypropylcellulose films

Tuning pore size and density of rigid polylactic acid foams through thermally induced phase separation and optimization using response surface methodology

Rigid polylactic acid (PLA) foams fabricated via thermally induced phase separation (TIPS) utilizing a ternary solution of PLA, Tetrahydrofuran (THF), and water. The PLA gels were stabilized mechanically by the substituting of the THF/water solvent mixture with ethanol as non-solvent and subsequently vacuum dried. A comprehensive characterization of PLA foams was achieved by Scanning Electron Microscopy (SEM), X-ray Diffractometry (XRD) and Brunauer-Emmett-Teller (BET) analyses. The BET area obtained in the PLA foam is up to 18.76 m2/g. The Response Surface Methodology (RSM) was utilized to assess the impacts of four independent variables (polymer concentration, solvent composition, quench temperature, and aging time) on the pore size and density of PLA foam. The experimental findings demonstrated that the fabrication parameters could be fine-tuned to govern the morphology of the pores, comprising their size and density. The optimal values of parameters for cell size were identified by RSM to be 8.96 (wt%), 91.60 (w/w), 5.50 °C, and 3.86 h for the optimum cell size of 37.96 µm (37.78 by Genetic Algorithm). Optimum density by RSM 88.88 mgr/cm3 (88.38 mgr/cm3 by Genetic Algorithm) was obtained at 5.00 (wt%), 89.33 (w/w), 14.40 °C and 2.65 h.

Structuring gelatin methacryloyl - dextran hydrogels and microgels under shear

Gelatin methacryloyl (GelMA) is a widely used semi-synthetic polymer for a variety of bioapplications. However, the development of versatile GelMA hydrogels requires tuning of their microstructure. Herein, we report the possibility of preparing hydrogels with various microstructures under shear from an aqueous two-phase system (ATPS) consisting of GelMA and dextran. The influence of an applied preshear on dextran/GelMA droplets and bicontinuous systems is investigated by rheology that allows the application of a constant shear and is immediately followed by in situ UV-curing of the GelMA-rich phase. The microstructure of the resulting hydrogels is examined by confocal laser scanning microscopy (CLSM). The results show that the GelMA string phase and GelMA hydrogels with aligned bands can be formed depending on the concentration of dextran and the applied preshear. The influence of the pH of the ATPS is investigated and demonstrates the formation of multiple emulsions upon decreasing the charge density of GelMA. The preshearing of multiple emulsions, following gelation, leads to the formation of porous GelMA microgels. The diversity of the formed structures highlights the application potential of preshearing ATPS in the development of functional soft materials.

Controlling the structure of spin-coated multilayer ethylcellulose/hydroxypropylcellulose films for drug release

Porous phase-separated ethylcellulose/hydroxypropylcellulose (EC/HPC) films are used to control drug transport out of pharmaceutical pellets. Water-soluble HPC leaches out and forms a porous structure that controls the drug transport. Industrially, the pellets are coated using a fluidized bed spraying device, and a layered film exhibiting varying porosity and structure after leaching is obtained. A detailed understanding of the formation of the multilayered, phase-separated structure during production is lacking. Here, we have investigated multilayered EC/HPC films produced by sequential spin-coating, which was used to mimic the industrial process. The effects of EC/HPC ratio and spin speed on the multilayer film formation and structure were investigated using advanced microscopy techniques and image analysis. Cahn-Hilliard simulations were performed to analyze the mixing behavior. A gradient with larger structures close to the substrate surface and smaller structures close to the air surface was formed due to coarsening of the layers already coated during successive deposition cycles. The porosity of the multilayer film was found to vary with both EC/HPC ratio and spin speed. Simulation of the mixing behavior and in situ characterization of the structure evolution showed that the origin of the discontinuities and multilayer structure can be explained by the non-mixing of the layers.

Cross-sectional structure evolution of phase-separated spin-coated ethylcellulose/hydroxypropylcellulose films during solvent quenching

Porous phase-separated ethylcellulose/hydroxypropylcellulose (EC/HPC) films are used to control drug transport out of pharmaceutical pellets. The films are applied on the pellets using fluidized bed spraying. The drug transport rate is determined by the structure of the porous films that are formed as the water-soluble HPC leaches out. However, a detailed understanding of the evolution of the phase-separated structure during production is lacking. Here, we have investigated EC/HPC films produced by spin-coating, which mimics the industrial manufacturing process. This work aimed to understand the structure formation and film shrinkage during solvent evaporation. The cross-sectional structure evolution was characterized using confocal laser scanning microscopy (CLSM), profilometry and image analysis. The effect of the EC/HPC ratio on the cross-sectional structure evolution was investigated. During shrinkage of the film, the phase-separated structure undergoes a transition from 3D to nearly 2D structure evolution along the surface. This transition appears when the typical length scale of the phase-separated structure is on the order of the thickness of the film. This was particularly pronounced for the bicontinuous systems. The shrinkage rate was found to be independent of the EC/HPC ratio, while the initial and final film thickness increased with increasing HPC fraction. A new method to estimate part of the binodal curve in the ternary phase diagram for EC/HPC in ethanol has been developed. The findings of this work provide a good understanding of the mechanisms responsible for the morphology development and allow tailoring of thin EC/HPC films structure for controlled drug release.

The EC/HPC/EtOH phase diagram could be estimated from the CLSM monitoring of the cross-sectional in situ phase separation. The findings of this work provide a good understanding of the structure evolution.